催化超临界水氧化对氨基苯酚

采用CuO／γ-Al2O3和MnO2/γ-Al2O3为催化剂、H2O2为氧化剂，在一连续流固定床反应器中进行了超临界水氧化对氨基苯酚实验。实验结果表明，CuO和MnO2催化剂对于对氨基苯酚的氧化降解具有显著的促进作用。对氨基苯酚的去除率随反应温度和压力的升高、停留时间的延长而提高，在24～26MPa和400～450℃条件下，数秒钟内COD去除率可达到99％以上，催化剂CuO／γ-Al2O3的催化效果优于MnO2／γ-Al2O3。证明了催化超临界水氧化技术的高效性。     

催化超临界水氧化偏二甲肼动力学研究

采用CuO/γ-Al2O3和MnO2/γ-Al2O3为催化剂、H2O2为氧化剂,在一连续流固定床反应器中进行了催化超临界水氧化偏二甲肼实验,得到了COD去除宏观动力学方程.在24 MPa、400～450℃和H2O2过量的情况下,反应对COD分别为1.11级(CuO)和1.26级(MnO2),对氧气分别为0.10级(CuO)和0.12级(MnO2).反应的活化能分别为35.75 kJ/mol(CuO)和37.79 kJ/mol(MnO2),前置因子A分别为9.35×102(CuO)和3.45 ×103(MnO2).     

常温常压催化湿式氧化降解偶氮染料废水的研究

以过渡金属Fe、Mn、Cu和Zn的硝酸盐为活性组分的前驱物,以γ-Al2O3为载体,制备了负载型催化剂Fe2O3/γ-Al2O3、MnO/γ-Al2O3、CuO/γ-Al2O3和ZnO/γ-Al2O3,并分别以H2O2和NaClO为氧化剂,对比了在常温常压条件下催化湿式氧化工艺处理甲基橙模拟废水的效果.结果表明,Fe2...     

Mn2O3/γ-Al2O3在超临界水氧化中催化活性的研究

采用浸渍法制备了Mn2O3/γ-Al2O3催化剂,在超临界水中催化氧化降解1,5-萘二磺酸,探索了催化剂Mn2O3活性组分负载量、催化剂空速和反应溶液pH对Mn2O3/γ-Al2O3催化剂活性的影响。结果表明：Mn2O3/γ-Al2O3的催化活性在一定范围内随Mn2O3活性组分负载量的增加而提高;在一定范围内,Mn2O3/γ-Al2O3空速越小,模拟废水的COD去除率越高;Mn2O3/γ-Al2O3催化活性在反应溶液呈酸性情况下比碱性时高。     

沸石载体催化剂研制及其催化臭氧氧化染料废水的研究

以沸石为载体负载不同金属氧化物来制备催化剂,通过试验分析该催化剂催化臭氧氧化染料废水的效果及其影响因素。结果表明:(1)沸石对染料废水的吸附作用很小,总有机碳(TOC)去除率基本维持在3.2%左右,对于后期的试验可以忽略其影响。(2)以沸石作为载体制得的MnO2、Fe2O3、ZnO、CuO负载型催化剂(分别简写为MnO2/沸石、Fe2O3/沸石、ZnO/沸石、CuO/沸石),对臭氧氧化反应均有催化作用,其催化效果依次为MnO2/沸石Fe2O3/沸石ZnO/沸石CuO/沸石。同时,MnO2/沸石的重复使用率高。(3)MnO2/沸石催化臭氧氧化效率及重复使用率均优于以活性炭为载体的MnO2负载型催化剂。(4)臭氧氧化和MnO2/沸石催化臭氧氧化对染料的脱色率基本一致。MnO2/沸石催化臭氧氧化的TOC去除率比臭氧氧化提高较多,对染料废水有很好的处理效果。(5)以沸石为载体制得的负载型催化剂催化臭氧氧化实际染料废水的处理效果较好,具有较高的实用价值。     

Mn203/γ-Al2O3在超临界水氧化中催化活性的研究

采用浸渍法制备了Mn2O3/γ-Al2O3催化剂,在超临界水中催化氯化降解1,5-萘二磺酸,探索了催化剂Mn2O3活性组分负载量、催化剂空速和反应溶液pH对Mn2O3/γ-Al2O3催化剂活性的影响.结果表明:Mn2O3/γ-Al2O3的催化活性在一定范围内随Mn2O3活性组分负载量的增加而提高;在一定范围内,Mn2O3/γ-Al2O3空速越小,模拟废水的COD去除率越高;Mn2O3/γ-Al2O3催化活性在反应溶液呈酸性情况下比碱性时高.     

催化湿式氧化中负载型催化剂的稳定性与应用

催化剂在应用过程中必须具有良好的催化活性和稳定性.优化制备的CuO/γ-Al2O3催化剂用于处理高浓度难降解的乳化液废水时具有良好的催化活性,在200℃时反应2 h,TOC去除率为81.3%,比未加催化剂的湿式氧化提高了14.9%.该催化剂对分散兰废水具有更高的活性和稳定性:在220℃反应1.5 h后,COD和TOC去除率分别为68.8%和56.5%,比非催化氧化分别提高了18.7%和18.9%.     

CuO/γ-Al_2O_3负载型催化剂催化燃烧处理油烟

采用等体积漫渍法制备不同CuO负载量的CuO/γ-Al2O3负载型催化剂,用X射线衍射仪、扫描电镜对该催化剂负载层活性组分的表面形态、晶相结构和颗粒大小进行表征,考察了该催化荆催化燃烧处理油烟的催化活性(以油烟净化效率表征).结果显示,催化活性随CuO负载量的增加.反应温度的升高而提高,但随烟气流量的增大而降低;在CuO负载量为20%(质量分数)、反应温度为350℃.烟气流量为5 L/min的最佳实验条件下,CuO/γ-Al2O3负载型催化剂的油烟净化效率最高.可达88.6%.该催化剂对油烟的催化燃烧具有较高的催化活性.     

扬水曝气强化催化氧化去除水中有机微污染物

以γ-Al2O3为载体,采用浸渍焙烧法制备了负载型催化剂RuO2-CeO2/γ-Al2O3、Fe2O3-CeO2/γ-Al2O3、Fe2O3/γ-Al2O3。在扬水曝气条件下,以西安某水源水库水为原水,考察了各催化剂对有机微污染物的净化效果,实验发现,催化剂反复多次使用并无明显失活现象,连续使用20 d以消除单纯吸附的影响后,仍然可在7 d内使UV254、CODMn、DOC的去除率分别达到38%、28%和27%。离子溶出实验表明,Fe2O3/γ-Al2O3有很好的稳定性。综合考虑处理效果、制备工艺以及制备成本,选择Fe2O3/γ-Al2O3为最佳催化剂。为了使催化剂Fe2O3/γ-Al2O3具有最佳活性,分别考察了焙烧时间、焙烧温度、浸渍液浓度、浸渍时间等,并对其制备工艺进行了优化。然后反应前后水样的分子量测定结果表明,反应后大分子比例下降,而小分子比例提高,说明催化氧化将一定量的大分子降解成为小分子。     

CuO/γ-Al_2O_3的制备及其湿式催化氧化性能研究

针对常温常压的废水双氧水催化氧化,采用浸渍法制备CuO/γ-Al2O3催化剂,利用比表面积、XRD手段表征了制备工艺对催化剂的影响,以模拟苯酚废水为研究对象考察催化剂的催化性能.研究表明,焙烧温度和活性组分含量等显著影响催化剂的性能,催化剂对双氧水催化氧化苯酚溶液具有较高的催化活性.     

Radionuclides and trace elements in fish collected upstream and downstream of Los Alamos national laboratory and the doses to humans from the consumption of muscle and bone

Abstract

The purpose of this study was to determine radionuclide and trace element concentrations in bottom‐feeding fish (catfish, carp, and suckers) collected from the confluences of some of the major canyons that cross Los Alamos National Laboratory (LANL) lands with the Rio Grande (RG) and the potential radiological doses from the ingestion of these fish. Samples of muscle and bone (and viscera in some cases) were analyzed for ³H, ⁹⁰Sr, ¹³⁷Cs, ^totU, ²³⁸Pu, ^239,240Pu, and ²⁴¹Am and Ag, As, Ba, Be, Cr, Cd, Cu, Hg, Ni, Pb, Sb, Se, and Tl. Most radionuclides, with the exception of ⁹⁰Sr, in the muscle plus bone portions of fish collected from LANL canyons/RG were not significantly (p<0.05) higher from fish collected upstream (San Ildefonso/background) of LANL. Strontium‐90 in fish muscle plus bone tissue significantly (p<0.05) increases in concentration starting from Los Alamos Canyon, the most upstream confluence (fish contained 3.4E‐02 pCi g^‐1 [126E‐02 Bq kg^‐1]), to Frijoles Canyon, the most downstream confluence (fish contained 14E‐02 pCi g^‐1 [518E‐02 Bq kg^‐1]). The differences in ⁹⁰Sr concentrations in fish collected downstream and upstream (background) of LANL, however, were very small. Based on the average concentrations (±2SD) of radionuclides in fish tissue from the four LANL confluences, the committed effective dose equivalent from the ingestion of 46 lb (21 kg) (maximum ingestion rate per person per year) of fish muscle plus bone, after the subtraction of background, was 0.1 ± 0.1 mrem y^‐1 (1.0 ± 1.0 μSv y^‐1), and was far below the International Commission on Radiological Protection (all pathway) permissible dose limit of 100 mrem y^‐1 (1000 μSv y^‐1). Of the trace elements that were found above the limits of detection (Ba, Cu, and Hg) in fish muscle collected from the confluences of canyons that cross LANL and the RG, none were in significantly higher (p<0.05) concentrations than in muscle of fish collected from background locations.     

Radionuclides in deer and elk from Los Alamos national laboratory and the doses to humans from the ingestion of muscle and bone

Abstract

This paper summarizes radionuclide concentrations (³H, ⁹⁰Sr, ¹³⁷Cs, ²³⁸Pu, ^239,240Pu, ²⁴¹Am, and ^totU) in muscle and bone tissue of mule deer (Odocoileus hemionus) and Rocky Mountain elk (Cervus elaphus) collected from Los Alamos National Laboratory (LANL), Los Alamos, New Mexico, lands from 1991 through 1998. Also, the committed effective dose equivalent (CEDE) and the risk of excess cancer fatalities (RECF) to people who ingest muscle and bone from deer and elk collected from LANL lands were estimated. Most radionuclide concentrations in muscle and bone from individual deer (n = 11) and elk (n = 22) collected from LANL lands were either at less than detectable quantities (where the analytical result was smaller than two counting uncertainties) and/or within upper (95%) level background (BG) concentrations. As a group, most radionuclides in muscle and bone of deer and elk from LANL lands were not significantly higher (p<0.10) than in similar tissues from deer (n = 3) and elk (n = 7) collected from BG locations. Also, elk that had been radio collared and tracked for two years and spent an average time of 50% on LANL lands were not significantly different in most radionuclides from road kill elk that have been collected as part of the environmental surveillance program. Overall, the upper (95%) level net CEDEs (the CEDE plus two sigma for each radioisotope minus background) at the most conservative ingestion rate (50 lbs of muscle and 13 lbs of bone) were as follows: deer muscle = 0.22 mrem y^‐1 (2.2 μSv y^‐1), deer bone = 3.8 mrem y^‐1 (38 μSv y^‐1), elk muscle = 0.12 mrem y^‐1 (1.2 μSv y^‐1), and elk bone = 1.7 mrem y^‐1 (17 μSv y^‐1). All CEDEs were far below the International Commission on Radiological Protection guideline of 100 mrem y^‐1 (1000 μSv y^‐1), and the highest muscle plus bone net CEDE corresponded to a RECF of 2E‐06, which is far below the Environmental Protection Agency upper level guideline of 1E‐04.     

Leaching of seven pesticides currently used in cotton crop in Mato Grosso State—Brazil

This study aimed to evaluate the leaching of pesticides and the applicability of the Attenuation Factor (AF) Model to predict their leaching. The leaching of carbofuran, carbendazim, diuron, metolachlor, α and β endosulfan and chlorpyrifos was studied in an Oxisol using a field experiment lysimeter located in Dom Aquino – Mato Grosso. The samples of percolated water were collected by rain event and analyzed. Chemical and physical soil attributes were determined before pesticide application to the plots. The results showed that carbofuran was the pesticide that presented a higher leaching rate in the studied soil, so was the one representing the highest contamination potential. From the total carbofuran applied in the soil surface, around 6 % leached below 50 cm. The other pesticides showed lower mobility in the studied soil. The calculated values to AF were 7.06E-12 (carbendazim), 5.08E-03 (carbofuran), 3.12E-17 (diuron), 6.66E-345 (α-endosulfan), 1.47E-162 (β-endosulfan), 1.50E-06 (metolachlor), 3.51E-155 (chlorpyrifos). AF Model was useful to classify the pesticides' potential for contamination; however, that model underestimated pesticide leaching.     

Endosulfan in China 2—emissions and residues

Background, aim, and scope  Endosulfan is one of the organochlorine pesticides (OCPs) and also a candidate to be included in a group of new persistent organic pollutants (UNEP 2007). The first national endosulfan usage inventories in China with 1/4° longitude by 1/6° latitude resolution has been reported in an accompanying paper. In the second part of the paper, we compiled the gridded historical emissions and soil residues of endosulfan in China from the usage inventories. Based on the residue/emission data, gridded concentrations of endosulfan in Chinese soil and air have been calculated. These inventories will provide valuable data for the further study of endosulfan. Methods  Emission and residue of endosulfan were calculated from endosulfan usage by using a simplified gridded pesticide emission and residue model—SGPERM, which is an integrated modeling system combining mathematical model, database management system, and geographic information system. By using the emission and residue inventories, annual air and soil concentrations of endosulfan in each cell were determined. Results and discussion  Historical gridded emission and residue inventories of α- and β-endosulfan in agricultural soil in China with 1/4° longitude by 1/6° latitude resolution have been created. Total emissions were around 10,800 t, with α-endosulfan at 7,400 t and β-endosulfan at 3,400 t from 1994 to 2004. The highest residues were 140 t for α-endosulfan and 390 t for β-endosulfan, and the lowest residues were 0.7 t for α-endosulfan and 170 t for β-endosulfan in 2004 in Chinese agricultural soil where endosulfan was applied. Based on the emission and residue inventories, concentrations of α- and β-endosulfan in Chinese air and agricultural surface soil were also calculated for each grid cell. We have estimated annual averaged air concentrations and the annual minimum and maximum soil concentrations across China. The real concentrations will be different from season to season. Although our model does not consider the transport of the insecticide in the atmosphere, which could be very important in some areas during some special time, the estimated concentrations of endosulfan in Chinese air and soil derived from the endosulfan emission and residue inventories are in general consistent with the published monitoring data. Conclusions  To our knowledge, this work is the first inventory of this kind for endosulfan published on a national scale. Concentrations of the chemical in Chinese air and agricultural surface soil were calculated for each grid cell. Results show that the estimated concentrations of endosulfan in Chinese air and soil agree reasonably well with the monitoring data in general. Recommendations and perspectives  The gridded endosulfan emission/residue inventories and also the air and soil concentration inventories created in this study will be updated upon availability of new information, including usage and monitoring data. The establishment of these inventories for the OCP is important for both scientific communities and policy makers.     

Impact of spiked concentrations of Cd,Pb, As and Zn in growth medium on elemental uptake of Nasturtium officinale (Watercress)

This study is aimed at investigating the impact of water quality on the uptake and distribution of three non-essential and toxic elements, namely, As, Cd and Pb in the watercress plant to assess for metal toxicity. The plant was hydroponically cultivated under greenhouse conditions, with the growth medium being spiked with varying concentrations of As, Cd and Pb. Plants that were harvested weekly for elemental analysis showed physiological and morphological symptoms of toxicity on exposure to high concentrations of Cd and Pb. Plants exposed to high concentrations of As did not survive and the threshold for As uptake in watercress was established at 5 ppm. Translocation factors were low in all cases as the toxic elements accumulated more in the roots of the plant than the edible leaves. The impact of Zn on the uptake of toxic elements was also evaluated and Zn was found to have an antagonistic effect on uptake of both Cd and Pb with no notable effect on uptake of As. The findings indicate that phytotoxicity or death of the watercress plant would prevent it from being a route of human exposure to high concentrations of As, Cd and Pb in the environment.     

Butyltin compounds in sediment and fish from the Polish Coast of the Baltic Sea

Concentrations of mono- (MBT), di- (DBT), and tri-(TBT) butyltin compounds were measured in eggs, liver, and muscle of nine species of fish from four regions of the Baltic Sea - the Firth of Vistula, the Gulf of Gdańsk, Puck Bay, and the mouth of the Vistula River. The overall concentration ranges among all the fish sampled from the four sites were: < 7 to 79 ng/g for MBT, 6 to 1100 ng/g for DBT, 7 to 3600 ng/g for TBT, and 16 to 4800 ng/g for total BTs, on a wet wt basis. The highest concentration of total BTs was found in herring liver from the Firth of Vistula (4800 ng/g, wet wt) and in roach muscle from Puck Bay (3300 ng/g, wet wt), while the least concentration was found in burbot eggs and liver from the Vistula River (39 and 32 ng/g, wet wt, respectively). TBT was the major form of BTs present in most samples analyzed. Sediment samples collected from shipyards in the Gulf of Gdańsk contained butyltin concentrations ranging from 1.2 to 46 μg/g (dry wt) for MBT, 2.0 to 42 μg/g for DBT, and 2.6 to 40 μg/g for TBT. As with the fish, the majority of the BTs in sediment were present as TBT, which suggested recent exposure of the aquatic environment of the region to TBT.     

Malathion-induced sublethal toxicity on the hematology of cricket frog (Fejervarya limnocharis)

The effect of malathion [diethyl(dimethoxythiophosphorylthio)succinate] at sublethal concentration (0.006 ppm) on hematological parameters of the cricket frog (Fejervarya limnocharis) was studied for 24 hrs to 240 hrs of exposure and remarkable hematological alterations were observed. The study on hematological parameters revealed a highly significant decrease (P < 0.01) in the total erythrocytes count in malathion-exposed animals from 24 hours to 96 hrs of exposure as compared to control. Significant decreases (P < 0.01) of hemoglobin and packed cell volume were also observed from 48 hrs to 240 hrs. A significant increase (P < 0.01) in leucocytes count was noted throughout the exposure period. Elevated numbers of lymphocytes and eosinophils as found in the present study revealed lymphocytosis as well as eosinophilia, suggesting that this was a result of direct stimulation of the immunological defense due to the presence of a toxic substance or may be associated with tissue damage. The cytomorphological and cytopathological study of erythrocytes and leucocytes in malathion-exposed frogs at 0.006 ppm concentration revealed various cytotoxic effects at different exposure times. It was noted that the size and the shape of the erythrocytes were subjected to variation in different blood disorders.     

Relation between forest vegetation, atmospheric deposition and site conditions at regional and European scales

Several monitoring programs have been set up to assess effects of atmospheric deposition on forest ecosystems. The aim of the present study was to evaluate effects on the understorey vegetation, based on the first round of a regional (the Netherlands) and a European forest monitoring program. A multivariate statistical analysis showed surprisingly similar results for both data sets; the vegetation appeared to be largely determined by the ‘traditional’ factors soil, climate, and tree species, but there was a small but statistically significant effect of atmospheric deposition. The effects of deposition include a slight shift towards nitrophytic species at high N deposition in the European network, and towards acidophytic species at high S-deposition in the Dutch network. The relatively small effect of atmospheric deposition is understandable in view of the very large natural variation in environmental conditions. Time series of both vegetation and environment are needed to assess deposition effects in detail.     

Influence of crop residues on trifluralin mineralization in a silty clay loam soil

Trifluralin is typically applied onto crop residues (trash, stubble) at the soil surface, or onto the bare soil surface after the incorporation of crop residues into the soil. The objective of this study was to quantify the effect of the type and amount of crop residues in soil on trifluralin mineralization in a Wellwood silty clay loam soil. Leaves and stubble of Potato (Solanum tuberosum) (P); Canola (Brassica napus) (C), Wheat (Triticum aestivum) (W), Oats (Avena sativa), (O), and Alfalfa (Medicago sativa) (A) were added to soil microcosms at rates of 2%, 4%, 8% and 16% of the total soil weight (25 g). The type and amount of crop residues in soil had little influence on the trifluralin first-order mineralization rate constant, which ranged from 3.57E-03 day^?1 in soil with 16% A to 2.89E-02 day^?1 in soil with 8% W. The cumulative trifluralin mineralization at 113 days ranged from 1.15% in soil with 16% P to 3.21% in soil with 4% C, again demonstrating that the observed differences across the treatments are not of agronomic or environmental importance.     

Concurrent nitrate and Fe(III) reduction during anaerobic biodegradation of phenols in a sandstone aquifer

The biodegradation of phenols (5, 60, 600 mg l⁻¹) under anaerobic conditions (nitrate enriched and unamended) was studied in laboratory microcosms with sandstone material and groundwater from within an anaerobic ammonium plume in an aquifer. The aqueous phase was sampled and analyzed for phenols and selected redox sensitive parameters on a regular basis. An experiment with sandstone material from specific depth intervals from a vertical profile across the ammonium plume was also conducted. The miniature microcosms used in this experiment were sacrificed for sampling for phenols and selected redox sensitive parameters at the end of the experiment. The sandstone material was characterized with respect to oxidation and reduction potential and Fe(II) and Fe(III) speciation prior to use for all microcosms and at the end of the experiments for selected microcosms.The redox conditions in the anaerobic microcosms were mixed nitrate and Fe(III) reducing. Nitrate and Fe(III) were apparently the dominant electron acceptors at high and low nitrate concentrations, respectively. When biomass growth is taken into account, nitrate and Fe(III) reduction constituted sufficient electron acceptor capacity for the mineralization of the phenols observed to be degraded even at an initial phenols concentration of 60 mg l⁻¹ (high) in an unamended microcosm, whereas nitrate reduction alone is unlikely to have provided sufficient electron acceptor capacity for the observed degradation of the phenols in the unamended microcosm.For microcosm systems, with solid aquifer materials, dissolution of organic substances from the solid material may occur. A quantitative determination of the speciation (mineral types and quantity) of electron acceptors associated with the solids, at levels relevant for degradation of specific organic compounds in aquifers, cannot always be obtained. Hence, complete mass balances of electron acceptor consumption for specific organic compounds degradation are difficult to confine. For aquifer materials with low initial Fe(II) content, Fe(II) determinations on solids and in aqueous phase samples may provide valuable information on Fe(III) reduction. However, in microcosms with natural sediments and where electron acceptors are associated with the sediments, complete mass-balances for substrates and electron acceptors are not likely to be obtained.