利用白云石回收污泥厌氧消化液中的磷

为经济有效地从污泥厌氧消化液中回收磷,构建了以白云石提供钙镁源的磷回收方法,探讨了磷回收的工艺条件与效果。通过盐酸酸化厌氧消化液以降低其碳酸盐含量,同时利用白云石溶于冷稀盐酸的特性使其钙镁缓慢释放到酸化的厌氧消化液中形成第一步磷回收体系,考察体系酸化pH、白云石与厌氧消化液的固液比以及反应pH对白云石的钙镁释放和磷回收效果的影响;第一步磷回收后的上清液为第二步厌氧消化液磷回收提供钙镁源,研究投加钙磷摩尔比对磷回收效果的影响。实验结果表明,当固液比为5.0时,在酸化pH为4.0～4.5且酸化溶出时间为10 h以及反应pH为9.0的条件下,第一步磷回收产物以磷酸钙盐沉淀为主,厌氧消化液磷回收率及回收产物含磷率（以P2O5计）分别达到99.43%和38.49%;第一步磷回收后的上清液按一定的钙磷摩尔比投加到酸化后的厌氧消化液中进行第二步磷回收,当投加钙磷摩尔比为0.20时,在反应pH为9.0的条件下,回收产物同时含有磷酸钙盐和磷酸铵镁,厌氧消化液中氮、磷回收率分别达到13.19%和90.90%,回收产物氮、磷含量（以P2O5计）分别为0.26%和39.58%;经XRD、XRF、ICP及SEM等分析表征,2步磷回收的产物以磷酸钙盐和磷酸铵镁为主要成分,杂质少。研究表明,利用白云石为钙镁源,通过分别构建不同的磷回收体系可以分步从污泥厌氧消化液中经济有效地回收磷,且磷回收率和回收产物含磷率高。     

酸性条件下剩余污泥中Ca2＋和Mg2＋溶出对磷回收的影响

为了在酸性条件下实现剩余污泥中磷的高效回收，对pH=3时剩余污泥水解酸化过程中氨氮、正磷酸盐和钙镁离子的溶出现象以及磷回收进行了研究分析。结果表明：当pH=3时，所溶出的氨氮、镁离子和钙离子与磷酸盐的摩尔比均大于1，能满足采用鸟粪石沉淀法或者羟磷灰石沉淀法回收磷的要求；但所溶出的钙镁离子的摩尔比大于1，会对鸟粪石沉淀法回收磷的顺利进行有较大影响；有无外加镁剂对磷回收率影响不大。采用改型后的镁型强酸性阳离子交换树脂进行离子交换可以得到较高纯度的鸟粪石沉淀产品，通过XRD检测其纯度为95％以上。     

酸性条件下剩余污泥中Ca2+和Mg22++溶出对磷回收的影响

为了在酸性条件下实现剩余污泥中磷的高效回收，对pH=3时剩余污泥水解酸化过程中氨氮、正磷酸盐和钙镁离子的溶出现象以及磷回收进行了研究分析。结果表明：当pH=3时，所溶出的氨氮、镁离子和钙离子与磷酸盐的摩尔比均大于1，能满足采用鸟粪石沉淀法或者羟磷灰石沉淀法回收磷的要求；但所溶出的钙镁离子的摩尔比大于1，会对鸟粪石沉淀法回收磷的顺利进行有较大影响；有无外加镁剂对磷回收率影响不大。采用改型后的镁型强酸性阳离子交换树脂进行离子交换可以得到较高纯度的鸟粪石沉淀产品，通过XRD检测其纯度为95%以上。     

酸-碱处理对剩余污泥水解酸化的影响

剩余污泥中富含有机质和营养元素可回收利用物质,污泥水解酸化液中的有机酸在去除或回收利用氨和磷后可作为进水化学需氧量(COD)不足的污水处理厂的补充碳源。通过控制pH,对比分析了不同处理方式(单独碱处理、酸-碱处理和碱-酸处理)对污泥水解酸化的影响。结果表明,单独碱处理的溶解性化学需氧量(SCOD)溶出量比酸碱联合处理要大16%左右,预处理第8天,达到5 406.1 mg/L。采用先酸(pH 4.0,4 d)后碱(pH 10.0,4 d)预处理,乙酸产量达到74.4 mg COD/g VSS,占总SCFAs的60.5%,产量及其占总短链脂肪酸(SCFAs)百分比含量均高于其他预处理方式。且酸-碱处理方式下NO4+-N和PO34--P溶出要优于其他处理方式。而单独碱处理方式下污泥减量效果最好,VSS去除率为36.6%。     

不同pH控制策略下剩余污泥中NH_4~+-N、PO_4~(3-)-P、COD溶出研究

污水处理厂的剩余污泥中富含氮、磷、COD,在其水解酸化过程中对pH条件进行控制,使污泥中的氮、磷、COD溶出到上清液中并进行回收利用是可行的。在22～25℃的温度条件下,1#反应器中剩余污泥先调节为酸性(pH=3),在实验第8 d氨氮、磷酸盐溶出量最多后调节为碱性(pH=10);3#反应器中剩余污泥先调节为碱性(pH=10),在实验第8 dCOD溶出量最多后调节为酸性(pH=3);2#反应器为对照实验,pH不进行调节。结果表明:若要以回收污泥中的氨氮、磷酸盐为主,剩余污泥由碱性(pH=10)调节为酸性(pH=3)优于由酸性(pH=3)调节为碱性(pH=10);若要回收污泥上清液中的COD为主,剩余污泥由酸性(pH=3)调节为碱性(pH=10)优于由碱性(pH=10)调节为酸性(pH=3)。     

不同pH控制策略下剩余污泥中NH+4-N、PO3-4-P、COD溶出研究

污水处理厂的剩余污泥中富含氮、磷、COD，在其水解酸化过程中对pH条件进行控制，使污泥中的氮、磷、COD溶出到上清液中并进行回收利用是可行的。在22~25℃的温度条件下,1#反应器中剩余污泥先调节为酸性（pH=3），在实验第8 d氨氮、磷酸盐溶出量最多后调节为碱性（pH=10）；3#反应器中剩余污泥先调节为碱性（pH=10），在实验第8 d COD溶出量最多后调节为酸性(pH=3)； 2#反应器为对照实验，pH不进行调节。结果表明：若要以回收污泥中的氨氮、磷酸盐为主，剩余污泥由碱性（pH=10）调节为酸性（pH=3）优于由酸性（pH=3）调节为碱性（pH=10）；若要回收污泥上清液中的COD为主，剩余污泥由酸性（pH=3）调节为碱性（pH=10）优于由碱性（pH=10）调节为酸性（pH=3）。     

不同pH控制策略下剩余污泥中NH4^＋-N、PO4^3--P、COD溶出研究

污水处理厂的剩余污泥中富含氮、磷、COD,在其水解酸化过程中对pH条件进行控制,使污泥中的氮、磷、COD溶出到上清液中并进行回收利用是可行的。在22～25℃的温度条件下,1#反应器中剩余污泥先调节为酸性（pH=3）,在实验第8 d氨氮、磷酸盐溶出量最多后调节为碱性（pH=10）;3#反应器中剩余污泥先调节为碱性（pH=10）,在实验第8 dCOD溶出量最多后调节为酸性（pH=3）;2#反应器为对照实验,pH不进行调节。结果表明：若要以回收污泥中的氨氮、磷酸盐为主,剩余污泥由碱性（pH=10）调节为酸性（pH=3）优于由酸性（pH=3）调节为碱性（pH=10）;若要回收污泥上清液中的COD为主,剩余污泥由酸性（pH=3）调节为碱性（pH=10）优于由碱性（pH=10）调节为酸性（pH=3）。     

污泥厌氧消化液中碳酸盐对回收磷的影响

为探讨污泥厌氧消化液中碳酸盐对以磷酸钙盐形式回收磷的影响,以粉煤灰浸出液为钙源,考察了消化液中的碳酸盐对磷回收过程和磷回收产物性质的影响。实验结果表明,在反应pH为10、反应钙磷摩尔比为1.67、反应时间为10 m in的条件下,消化液碳酸盐浓度为2 400 mg/L(以CaCO3计)时,磷的回收率为78.53%,回收产物中磷含量(以P2O5计)为28.93%;对消化液进行盐酸预酸化使pH达到4及以下时,磷回收率接近100%,回收产物中磷含量(以P2O5计)达到43.08%。消化液中碳酸盐的存在易形成碳酸钙沉淀,从而降低了磷回收率、回收产物中磷含量以及回收产品的纯度;预酸化能够有效地去除消化液中的碳酸盐并降低了其对磷回收的不利影响。     

剩余污泥超声预处理后水解酸化特性

为探讨剩余污泥超声预处理后的水解酸化特性,考察了0.6 W/mL、5 min和1 W/mL、5 min 2种超声预处理条件下污泥水解酸化过程有机质、氮、磷的释放情况。实验结果表明,2种超声预处理均可促进污泥水解酸化,并且0.6 W/mL比1 W/mL的超声预处理更有利于SCOD的释放、VFAs的产生以及氮和磷的释放;水解酸化初期,超声预处理比未经超声预处理的污泥在有机质、氮、磷释放率上差异非常明显,随着水解酸化的进行,有机质和氮释放率差异仍很明显,而磷释放程度逐渐接近;经0.6 W/mL超声预处理,污泥水解酸化3 d后,SCOD释放率、VFAs浓度、TN释放率和NH4+-N释放率分别是未经处理污泥的1.85、2.63、1.85和1.41倍,而TP和PO43--P释放率较未经处理污泥仅分别多2.44和1.23个百分点。研究表明,控制适宜的声能密度、超声时间和水解酸化进程是超声预处理强化剩余污泥水解酸化效果的关键。     

pH对混合污泥水解酸化的影响

pH对剩余污泥和初沉污泥水解酸化的影响已有报道,但pH对混合污泥水解酸化的影响尚鲜见报道。为此对厌氧环境,(20±1)℃,pH=4～11以及不控制pH条件下混合污泥的水解酸化特征进行了研究。研究发现:对pH调控有利于污泥SCOD的溶出,在较强的碱性条件下污泥溶出的SCOD要大于其他条件下的,特别是pH=10和11条件下污泥溶出的SCOD要远高于其他条件下。碱性环境和酸性环境以及中性环境相比更有利于混合污泥产酸,最佳产酸pH条件为pH=10。在酸性和极端碱性条件下均有利于混合污泥中氨氮和磷的释放。碱性环境利于挥发性悬浮固体(VSS)的去除,但不利于总悬浮固体(TSS)的去除。在不同pH条件下将混合污泥的发酵特征和剩余污泥和初沉污泥发酵特征比较,发现3种污泥水解和产酸均在碱性条件下最好,且在20～22℃的条件下,产酸量均在pH=10的条件下达到最大。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.