双转盘反应器光催化处理罗丹明B

采用溶胶—凝胶法制备的TiO2/Ti电极为光阳极,Cu、Fe、Zn或C为阴极,组成双转盘反应器,以罗丹明B(RhB)为目标污染物,考察了反应条件对光催化效率的影响.结果表明,最佳反应条件:阴极材料为Cu;转盘转速为70 r/min;初始pH为2.5；Na2SO4质量浓度为1.0 g/L; RhB初始质量浓度为20 mg/L.在最佳反应条件下,处理RhB模拟废水30 min的脱色率可达到99.9％.双转盘反应器处理不同浓度的RhB时,其脱色率是单转盘的1.12～2.33倍,且倍数随着RhB浓度增大而增加,表明双转盘反应器可高效地光催化处理高浓度染料废水.     

TiO2/Ti转盘液膜反应器光电催化处理罗丹明B

采用溶胶-凝胶法制备了TiO2/Ti电极,X射线衍射(XRD)分析表明,TiO2主要为锐钛矿,晶粒尺寸约为46 nm.以TiO2/Ti电极作阳极,Cu电极作阴极,组装成转盘液膜反应器,考察了其光电催化处理染料罗丹明B(RhB)的影响因素(转盘转速、偏压、溶液初始pH、RhB初始浓度和电解质浓度).得到最佳处理条件为:转盘转速90 r/min,偏压0.4V,溶液初始pH2.5,电解质(硫酸钠)质量浓度0.5 g/L.在最佳处理条件下,处理20 mg/L RhB染料废水90 min的脱色率和总有机碳(TOC)去除率分别达到97.2％和72.7％.结果表明,由于同时强化了激发光源的利用率和溶液的传质效率,TiO2/Ti转盘液膜反应器可高效光电催化处理染料废水.     

改性钛白石膏对阳离子染料罗丹明B的吸附性能

通过不同温度煅烧改性实验比较,选择用800℃煅烧的钛白石膏作为吸附剂,研究其对阳离子染料罗丹明B(Rhodamine B,RhB)的吸附特性。利用XRD,SEM,BET对改性钛白石膏进行表征,考察了溶液pH,温度,接触时间,投加量对吸附的影响。结果表明,当RhB溶液质量浓度为9.58 mg/L,pH值为7.0,吸附剂投加量为2 g/L,吸附时间为150 min时,改性钛白石膏对RhB的最大吸附量为2.3 mg/g,较原土提高了140.1%左右。溶液温度和吸附剂投加量对钛白石膏吸附RhB吸附有很大的影响。利用准一阶,准二阶动力学模型对吸附数据进行模拟,发现该吸附过程更符合准二阶动力学模型,Langmuir和Freundlich两种吸附等温模型都能较好地描述改性钛白石膏吸附RhB的过程。通过热力学计算,得到△H0为18.5kJ/mol,△G00,表明该吸附反应为自发进行的吸热反应。     

硫酸活化市政污泥吸附Pb2+

以城市污水厂脱水剩余污泥为原材料,采用硫酸活化法制备活化剩余污泥,讨论了溶液初始pH、铅离子的浓度、接触时间和吸附剂投加量等因素对处理含铅废水效能影响,探讨了其吸附动力学特征.结果表明,活化剩余污泥对铅离子有较好吸附效果,10 min内吸附率达到75％,45 min内吸附基本达到平衡,在偏酸性或中性条件下,吸附容量随着初始pH增大而增大.采用4种动力学方程(准一级吸附动力学方程、准二级吸附动力学方程、颗粒扩散吸附动力学方程、Elov-ich动力学方程)对其吸附数据进行吸附动力学拟合,通过分析得出,准二级吸附动力学方程能较好地反映该吸附过程,其相关系数R2均达到0.999以上.     

纳米铁催化分解高氯酸盐废水的反应动力学

通过实验考察了酸性条件下纳米铁催化分解高氯酸盐过程中的影响因素,对其分解的动力学进行了研究,并对纳米铁催化剂结构及微观形貌进行SEM、EDS和XRD表征分析。利用阿仑尼乌斯方程和幂指数方程拟合反应动力学方程,获得了高氯酸盐分解动力学方程Ct=C0exp{-0.03773exp(-201.65/T)[H]0.191t},理论的计算值与实验值吻合较好,误差在15%以内。     

电化学转盘/电凝聚法处理模拟活性染料废水的研究

采用一种新的电化学方法--电化学转盘/电凝聚法来处理模拟活性翠蓝KN-G废水,考察了电压、转速、pH、反应时间对色度、TOC去除率的影响,并确定了最佳反应条件.在最佳反应条件(电压12 V,转速70 r/min,pH为4～5,反应时间为60 min)下,色度和TOC去除率可分别达到95.3%和73.5%.并初步探讨了活性翠蓝KN-G的降解机理.     

好氧氨氧化菌混培物的氨氧化动力学研究

采用批式呼吸法求得好氧氨氧化菌产率系数为0.2119 mg COD/mg NH4 -NOD(或者0.7268 mg COD/mg NH4 -N)和氨氧化菌最大氨氮降解速率为0.1 mg NOD/(mg COD·h)(或者0.0292 mg N/(mg COD·h)).用间歇式批试验法,加入24 μmol/L NaN3抑制NO2--N氧化,建立氨氧化反应动力学方程,得到氨氮半饱和系数为18.38 mg NOD/L(或者5.36 mg NH4 -N/L),DO半饱和系数为0.494 mg/L.对比参数值表明,用一步硝化动力学来描述氨氧化反应动力学模型是错误的.     

铁铜内电解处理二步湿法腈纶聚合单元废水

采用铁铜内电解法处理二步湿法腈纶聚合单元废水,考察了不同反应条件对COD去除率的影响.实验结果表明:最优条件为pH 3、搅拌转速600r/min、铁量为300g、硫酸铜的量为10 g、反应时间90 min.在此情况下,COD去除率达到70%,出水B/C值由0.2提高到0.57.降解反应符合四级反应动力学方程.在有机物去...     

臭氧气泡大小对分散染料废水氧化处理效果的影响

采用臭氧氧化法处理实际分散染料废水,研究了初始pH、臭氧投加量、反应时间、臭氧气泡大小(气体洗瓶和自制的砂芯鼓泡反应柱分别作反应器)对处理效果的影响,采用动态显微高速摄影仪对反应器内的臭氧气泡进行了表征.结果表明,反应体系的初始pH、臭氧投加量越高,反应速率越快,染料废水的脱色及矿化效果越好；染料废水的臭氧氧化处理过程符合拟二级动力学方程；自制的砂芯鼓泡反应柱改善了臭氧分散效果,缩小了气泡直径,提高了臭氧传质速率和效率,强化了臭氧氧化能力.     

氨基修饰增强的Fe/Cu-MOF对罗丹明B的光催化降解性能及相关机理

利用溶剂热合成法合成了氨基修饰的Fe/Cu-MOF-NH2,分别采用XRD、SEM、N2吸附-脱附、UV-vis、EA等检测方法进行了表征分析,并将其用于RhB的光催化降解,考察了 RhB的初始质量浓度、催化剂质量浓度和pH对光催化降解的影响.结果表明,氨基的引入显著提升了催化剂的可见光响应性能;在合成Fe/Cu-MO...     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.