Contents and sources of polycyclic aromatic hydrocarbons and organochlorine pesticides in vegetable soils of Guangzhou, China

We investigated contents, distribution and possible sources of PAHs and organochlorine pesticides (Ops) in 43 surface and subsurface soils around the urban Guangzhou where variable kinds of vegetables are grown. The results indicate that the contents of PAHs (16 US EPA priority PAHs) range from 42 to 3077 microg/kg and the pollution extent is classified as a moderate level in comparison with other investigations and soil quality standards. The ratios of methylphenanthrenes to phenanthrene(MP/P), anthracene to anthracene plus phenanthrene (An/178), benz[a]anthracene to benz[a]anthracene plus chrysene (BaA/228), indeno[1,2,3-cd]pyrene to indeno[1,2,3-cd]pyrene plus benzo[ghi]perylene (In/In+BP) suggest that the sources of PAHs in the soil samples are mixed with a dominant contribution from petroleum and combustion of fossil fuel. The correlation analysis shows that the PAHs contents are significantly related to total organic carbon contents (TOC) (R2=0.75) and black carbon contents (BC) (R2=0.62) in the soil samples. Dichlorodiphenyltrichloroethane and metabolites (DDTs) and hexachlorocyclohexanes and metabolites (HCHs) account largely for the contaminants of OPs. The concentrations of DDTs range from 3.58 to 831 microg/kg and the ratios for DDT/(DDD+DDE) are higher than 2 in some soil samples, suggesting that DDT contamination still exists and may be caused by its persistence in soils and/or impurity in the pesticide dicofol. The concentrations of HCHs are 0.19-42.3 microg/kg.     

Distribution of polycyclic aromatic hydrocarbons in thirty typical soil profiles in the Yangtze River Delta region, east China

Polycyclic aromatic hydrocarbons (PAHs) were quantified in 30 soil profiles from the Yangtze River Delta Region, in east China. Relative concentrations of PAH compounds with different benzene rings and ratios of fluoranthene to fluoranthene plus pyrene and benz(a)anthracene to benz(a)anthracene plus chrysene were used to identify the possible sources of soil PAHs. Total concentrations of 15 PAHs in topsoils ranged from 8.6 to 3881 microg kg(-1) with an average of 397 microg kg(-1). Half of the soil samples were considered to be contaminated with PAHs (>200 microg kg(-1)) and two sampling sites were heavily polluted by PAHs with concentrations >1000 microg kg(-1). Phenanthrene was found in soils below a depth of 100 cm in half of the sampling sites, but the detectable ratio of benzo(a)pyrene decreased sharply from 100% in topsoil to 0 in the 4th horizon.     

采油废水中多环芳烃的生态风险评价

先利用C-18固相萃取小柱富集大港油田港东联合处理站污水处理站的采油废水中16种多环芳烃(PAHs,即萘、苊烯、苊、芴、菲、蒽、荧蒽、芘、、苯并[a]蒽、苯并[b]荧蒽、苯并[k]荧蒽、苯并[a]芘、茚并[1,2,3-cd]芘、二苯并[a,h]蒽和苯并[g,h,i]苝),再用气相色谱/质谱(GC/MS)分析测定其浓度,以评价PAHs的去除率和生态风险。结果表明:(1)采油废水经处理后,COD、石油类去除率分别达到82.27%、91.06%;外排水COD、石油类达到《污水综合排放标准》(GB 8978—1996)一级标准要求,优于中国采油废水处理的一般水平。(2)采油废水主要以2、3环的PAHs为主,约占总量的93%以上。(3)苯并[a]芘超过《地表水环境质量标准》(GB 3838—2002)中限值。(4)处理前的采油废水中蒽、菲和苯并[a]芘具有一定的生态风险;处理后的外排水中萘、蒽、菲、荧蒽、苯并[a]芘的暴露浓度(PEC)/预测无效应浓度(PNEC)均小于1,目前尚未对环境造成威胁。但是8种PAHs(苊烯和苯并类PAHs除外)总和表现出较大的毒性,需要引起重视。     

GC/MS analysis of polynuclear aromatic hydrocarbons in sediment samples from the Niger Delta region

Thirteen sediment samples from different locations in the Niger Delta region of Nigeria were analyzed for the presence of 16 polynuclear aromatic hydrocarbons (PAHs) via gas chromatography/mass spectrometry. The specific target compounds for this study included naphthalene, acenaphthylene, acenaphthene, flourene, phenanthrene, anthracene, flouranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]flouranthene, benzo[a]pyrene, benzo[ghi]perylene, dibenz[a,h]anthracene, and indeno[1,2,3-cd]pyrene. Four isotopically labeled polynuclear aromatic hydrocarbons (acanaphthene-d10, phenanthrene-d10, chrysene-d12 and perylene-d12) were used for internal standardization. All 16 PAHs were found in most of the thirteen samples with concentration ranging from 0.1 microg/kg to 28 microg/kg. It was also found that the 5 and 6-ring PAHs were present in higher concentrations than all the other compounds, indicating their high resistance to microbial degradation.     

Leaves of Quercus ilex L. as biomonitors of PAHs in the air of Naples (Italy)

Polycyclic aromatic hydrocarbons (PAHs) were determined by the GC-MS chromatography in the leaves of Quercus ilex L., an evergreen Mediterranean oak, to monitor the degree of pollution in the urban area of Naples compared to remote areas. Leaf samples were collected in July 1998 from four urban parks, six roadsides and two sites in remote areas. The total PAH contents in Q. ilex leaves ranged from 106.6 in a control site to 4607.5 ng/g d.w. along a road with a high traffic flow. The mean concentration factors (urban/control) were 3.8 for the parks and 15 for the roads. The contribution of carcinogenic PAHs (benz[a]anthracene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, indeno[1,2,3-c,d]pyrene) was higher in urban area and differed according to the site, ranging from 6.7% to 21.3%. The total PAH burden in control sites was dominated by the low molecular weight PAHs, whilst along the urban roads fluoranthene, pyrene and benz[a]anthracene among the measured PAHs showed the highest values. PAHs were positively correlated (P<0.01) to trace metals measured in a previous study.     

Distribution,sources, and risk assessment of polycyclic aromatic hydrocarbons (PAHs) in surface water in industrial affected areas of the Three Gorges Reservoir,China

Water samples were collected from wastewater treatment plant (WWTP), drain water (DW), major tributaries (MT), and main course of the Yangtze River (MY) in areas of three industrial parks (IPs) in Chongqing city in the Three Gorges Reservoir (TGR). Sixteen EPA priority polycyclic aromatic hydrocarbon (PAH) pollutants were quantified to identify the effects of industrial activities on water quality of the TGR. The results showed that 11 individual PAHs were quantified and 5 PAHs (naphthalene (Nap), acenaphthylene (Acy), benzo[k]fluoranthene (BkF), indeno[1,2,3-cd]pyrene (InP), and benzo[g,h,i]perylene (BgP)) were under detection limits in all of the water samples. Three-ring and four-ring PAHs were the most detected PAHs. Concentrations of individual PAHs were in the range of not detected (nd) to 24.3 ng/L. Total PAH concentrations for each site ranged from nd to 42.9 ng/L and were lower compared to those in other studies. The mean PAH concentrations for sites WWTP, DW, MT, and MY showed as follows: DW (25.9 ng/L) > MY (15.5 ng/L) > MT (14.0 ng/L) > WWTP (9.3 ng/L), and DW contains the highest PAH concentrations. Source identification ratios showed that petroleum and combustion of biomass coal and petroleum were the main sources of PAHs. The results of potential ecosystem risk assessment indicated that, although PAH concentrations in MT and MY are likely harmless to ecosystem, contaminations of PAHs in DW were listed as middle levels and some management strategies and remediation actions, like strengthen clean production processes and banning illegal sewage discharging activities, etc., should be taken to lighten the ecosystem risk caused by PAHs especially risks caused by water discharging drains.     

Occurrence and assessment of polycyclic aromatic hydrocarbons in soils from vegetable fields of the Pearl River Delta, South China

Surface soil (0-20 cm) samples from nine representative vegetable fields located in Guangzhou, Shenzhen, Zengcheng and Huadu within the Pearl River Delta, South China were collected and analyzed for 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs) using gas chromatography coupled to mass spectrometry (GC-MS). Total concentrations of 16 PAHs (Sigma(PAHs)) ranged from 160 to 3700 microg kg(-1). Large variations were observed also between concentrations of individual PAHs from different vegetable fields and within the site as well. Acenapthylene, benzo[b]fluoranthene, fluoranthene, benzo[a]pyrene and benzo[k]fluoranthene were consistently the most prevalent individual PAHs. The values of PAH isomer ratios [anthracene/(anthracene+phenanthrene) and fluoranthene/(fluoranthene+pyrene)] indicate that combustion processes are the major sources of PAHs. Concentrations of PAHs were poorly correlated with organic carbon concentrations of soils, suggesting different sources and also indicating that the PAH pollution of this area is recent. The same outcome is confirmed by the predominance of PAHs with fewer rings (相似文献   

Polycyclic aromatic hydrocarbons in marine organisms from the Adriatic Sea, Italy

Polycyclic aromatic hydrocarbons (PAHs) were analyzed in bivalves (Mitylus galloprovincialis), cephalopods (Todarodes sagittatus), crustaceans (Nephrops norvegicus) and fish (Mullus barbatus, Scomber scombrus, Micromesistius poutassou, Merluccius merluccius) in several pools coming from the Central Adriatic Sea. These marine organisms were selected because of their multitude, wide distribution and common use in the Italian diet, they were sampled and analyzed during the year 2004. Acenaphthene, benzo(a)pyrene, dibenz(a,h)anthracene, benzo(ghi)perylene and indeno(1,2,3-cd)pyrene showed levels below the instrumental detection limit in all samples. Fluorene, phenanthrene, anthracene, fluoranthene, benz(a)anthracene, benzo(b)fluoranthene and benzo(k)fluoranthene were detected at different concentrations in analyzed samples. Chrysene was detected only in mussels with very low values (average 0.74ngg(-1) wet weight). PAHs composition pattern was dominated by the presence of PAHs with 3-rings (62%) followed from those with 4-rings (37%) and 5-rings (1%). Atlantic mackerel, European hake and blue whiting showed the highest PAH concentrations, ranging from 44.1 to 63.3ngg(-1) wet weight, the group of invertebrate organisms showed a level of contamination about three times lower than those of the vertebrate groups. Mediterranean mussels that did not present very high levels of contamination expressed as sum of PAHs showed one of the highest values of benzo(a)pyrene equivalents (BaPEs). Conversely the latter value was very low in Atlantic mackerel even if this species reported the highest total PAH concentrations. No significant correlation was observed between weight, length and trophic levels and total PAHs.     

Studies on polycyclic aromatic hydrocarbons in two sediment cores from the huaxi reservoir,china: Assessment of levels,sources, and ecological risk

This study investigated the levels, sources and ecological risks of 16 polycyclic aromatic hydrocarbons (PAHs) in two sediment cores that were collected along the Huaxi Reservoir. The spatial distributions and residue levels of the 16 priority PAHs in the sediments from the Huaxi Reservoir were analyzed for their potential ecological risk, source apportionment and contribution to the total PAH residue. The concentration level of the total PAHs (TPAHs) was in the range 1805 ng·g^?1 to 20023 ng·g^?1 based on dry weight, and the content of PAHs in the Huaxi Reservoir exhibited a gradual upward trend. The PAH congener ratios fluoranthene/(fluoranthene + pyrene) and indeno[1, 2, 3-cd]pyrene/(indeno[1, 2, 3-cd]pyrene + benzo[g, h, i]perylene) were used to identify the source. The main source of the low molecular weight PAHs was wood and coal combustion, whereas the high molecular weight PAHs were primarily from petroleum combustion sources. The results of an ecological risk assessment demonstrated that ACE poses a potential ecological risk, while FLU, NAP, ANT, BaP, DBA, PHEN and PYR can have serious ecological risks.     

Contamination of polycyclic aromatic hydrocarbons (PAHs) in microlayer and subsurface waters along Alexandria coast,Egypt

The residues of seven polycyclic aromatic hydrocarbons (PAHs) pollutants in microlayer and subsurface seawater samples collected from Alexandria coast, Egypt, were analyzed by gas chromatography–electron-impact mass spectrometry-selected ion monitoring mode (GC–MS-SIM). The pollutants studied were, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene and benzo[a]pyrene. Total PAH levels in microlayer ranged from 103 to 523 ng/l, while it ranged in subsurface samples from 13 to 120 ng/l. The Western Harbor location recorded the highest level of PAHs pollutant over all the other location for both subsurface and microlayer waters. The two major PAHs in microlayer water at the Western Harbor were fluorene and phenanthrene, making up 27% and 20% of the total PAHs, while the two major PAHs in subsurface water at the Eastern Harbor were phenanthrene and fluoranthene recording up 21% each of the total PAHs. The total PAH levels were generally in the nano-gram per liter for microlayer and subsurface seawater samples. The dominant PAHs in both subsurface and microlayer samples were fluoranthene, pyrene and benzo[a]pyrene. The microlayer enrichment factor at Alexandria’s Mediterranean coast was ranged from 29 for fluorene to 3 for phenanthrene and benzo[a]pyrene which showed PAHs concentration in the microlayer with an average of five times more than the total PAH in the subsurface samples.     

The effect of ryegrass (Lolium perenne) on decrease of PAH content in long term contaminated soil

The biodegradation of polycyclic aromatic hydrocarbons in microecosystems containing long-term contaminated soil was investigated. Soil was contaminated by different chemicals, including PAHs since World War II. Aging of the soil was expected to act as a principal factor limiting biodegradation. Half of the microecosystems contained ryegrass (Lolium perenne) and long-term selected natural soil microflora originally present in contaminated soil. The others contained contaminated soil with natural microflora only. Half of the microecosystems in each parallel experiment was fertilised with N-P-K fertiliser. Cultivation was carried out at 12 and 18 months in a greenhouse with a natural photoperiod and the ability to degrade 15 chosen PAH was investigated. For analysis, the soil from each pot was divided into three horizontal layers for mutual comparison among layers and each layer was further divided into four equal samples. Soil extracts were analysed using HPLC. After a one-year-cultivation period the content of the monitored PAHs declined to 50%. Mostly, there were no significant differences between the microecosystems. Best degraded were fluoranthene and pyrene, which were the major contaminants present in original soil. Also, other compounds were successfully degraded, even benzo[a]pyrene and benzo[ghi]perylene. Dibenz[a,h]anthracene and indeno[1,2,3-cd]pyrene were the only PAHs, examined that showed no significant degradation. Although some differences between the soil layers were detected, no conclusive trends could be found. However, significantly lower concentrations of PAHs were determined mostly in the bottom layer of the analysed profiles. In vegetated microecosystems the decline of PAHs concentrations was more remarkable after 18 months cultivation.     

The temporal variability of the profile of carcinogenic polycyclic aromatic hydrocarbons in urban air: a study in a medium traffic area in Rome, 1993–1998

The constancy, both temporal and spatial, of the profile of polycyclic aromatic hydrocarbons (PAHs) relative to benzo[a]pyrene (BaP) is a prerequisite to using the BaP-indicator approach in the carcinogenic risk assessment for PAHs. The principal aim of this study was to provide a contribution to validate this approach, by studying the variability of the profile at a typical urban site through a multi-year data set and by comparing the profiles available for different cities. Seven carcinogenic PAHs (benz[a]anthracene, benzo[b+j+k]fluoranthenes, BaP, indeno[1,2,3-cd]pyrene, dibenz[a,h]anthracene) were determined in PM₁₀ 24-h samples collected every third day at a road site; moreover, benzo[e]pyrene was determined as a reference PAH due to its stability. The profile was found stable from year to year. Besides, it was similar to those recently found in other European cities (observed differences within a factor of four) and to those elaborated from earlier (1970s–1980s) investigations. The substantial similarity of profiles, both temporal (on an annual basis) and spatial, supports the validity of the BaP-indicator approach. Large PAH-to-PAH differences were, however, found in the seasonal pattern of profile: they were explained by the different atmospheric degradability of PAHs, whose effect is enhanced under the meteoclimatic conditions typical of the European Mediterranean countries. PAH annual means showed a slight declining trend since 1994. In the last sampling year, mean concentration of BaP was 1.2 ng m⁻³. Within-year differences among monthly averaged PAH concentrations were observed, as large as up to 44-fold for BaP, underlining the need for whole-year monitoring.     

In vitro EROD induction equivalency factors for the 10 PAHs generally monitored in risk assessment studies in The Netherlands

The ethoxy resorufin dealkylase (EROD) inducing potency of 10 polycyclic aromatic hydrocarbons (PAHs) is measured in the H4IIE in vitro bioassay and the results are compared to those reported in literature. The selected PAHs varied considerably in their potency to induce EROD activity. Anthracene (Ant) and phenanthrene (Phe) showed consistently no response. Naphthalene (Nap) showed no or a very weak response on EROD activity. Fluoranthene (Fla) and benzo[g,h,i]perylene (BghiP) showed weak responses at the highest doses. The other PAHs, including indeno[1,2,3-cd]pyrene (IP), benz[a]anthracene (BaA), benzo[a]pyrene (BaP), chrysene (Chr) and benzo[k]fluoranthene (BkF), showed full bell shaped dose-response curves. BaP EROD induction equivalency factors (BaP-1EF) were calculated and increased in the order Ant approximately Phe < Fla < Nap < BghiP < IP < BaA < BaP < Chr < BkF. Comparison of BaP-IEFs based on 50% effect concentration (EC50) or lowest effect concentration (LEC), yielded a significant relationship between both methods described by the equation log(BaPIEF(EC50) = 0.55 x log(BaPIEF(LEC)) + 0.07 (r2 = 0.913). BaP-IEFs as derived from our measurements and as reported in literature and measured in other in vitro assays deviated up to a factor of 17 among the different studies, but the potency rankings were comparable. For the PAH mixture as on average present in the human diet an overall tetrachlorodibenzo-p-dioxin (TCDD)-IEF of 1 x 10(-4) was estimated. The total PAH based TCDD induction equivalents (IEQ) intake then was calculated 300 pg/day, which is approximately 2 times higher then the PHAH based TCDD-EQ intake reported for humans.     

Profiles of PAH emission from steel and iron industries

In order to characterize the polycyclic aromatic hydrocarbons (PAHs) emission from steel and iron industries, this study measured the stack emission of twelve steel and iron plants in southern Taiwan to construct a set of source fingerprints. The study sampled the emissions by the USEPA's sampling method 5 with the modification of Graseby for the gas and particulate phase PAH and, then, used Hewlett-Packard 5890 gas chromatograph equipped with mass spectrometer detector to analyze the samples. The steel and iron industries are classified into three categories on the basis of auxiliary energy source: Category I uses coal as fuel, Category II uses heavy oil as fuel and Category III uses electric arc furnace. The pollution source profiles are obtained by averaging the ratios of individual PAH concentrations to the total concentration of 21 PAHs and total particulate matter measured in this study. Results of the study show that low molecular weight PAHs are predominant in gas plus particulate phase for all three categories. For particulate phase PAHs, however, the contribution of large molecular weight compounds increases. Two-ring PAHs account for the majority of the mass, varying from 84% to 92% with an average of 89%. The mass fractions of 3-, 4-, 5-, 6-ring PAHs in Category I are found to be more than those of the other two categories. The mass of Category III is dominated by 7-ring PAHs. Large (or heavy) molecular weight PAHs (HMW PAHs) are carcinogenic. Over all categories, these compounds are less than 1% of the total-PAH mass on the average. The indicatory PAHs are benz[a]anthracene, benzo[k]fluoranthene, benzo[ghi]perylene for Category I, benzo[a]pyrene, acenaphthene, acenaphthylene for Category II and coronene, pyrene, benzo[b]chrycene for Category III. The indicatory PAHs among categories are very different. Thus, dividing steel and iron industry into categories by auxiliary fuel is to increase the precision of estimation by a receptor model. Average total-PAH emission factors for coal, heavy oil and electric arc furnace were 4050 μg/kg-coal, 5750 μg/l-oil, 2620 μg/kW h, respectively. Carcinogenic benzo[a]pyrene for gas plus particulate phase was 2.0 g/kg-coal, 2.4 μg/l-oil and 1.4 μg/kW h for Category I, II and III, respectively.     

Chemical characterization and source identification of polycyclic aromatic hydrocarbons in aerosols originating from different sources

To obtain the characteristic factors or signatures of particulate polycyclic aromatic hydrocarbons (PAHs) to help identify the sources of particulate PAHs in the atmosphere, different carbonaceous aerosols were generated by burning different fossil fuels and biomass under different conditions in the laboratory, and the chemical characteristics of 14 PAHs were studied in detail. The results showed that (1) carbonaceous aerosols derived from domestic burning of coal, diesel fuel, and gasoline have much higher concentrations of PAHs than those derived from domestic burning of biomass; (2) carbonaceous aerosols derived from domestic burning of diesel fuel/gasoline have similar PAH components as those derived from high-temperature combustion of diesel fuel/gasoline, although the former have much higher concentrations of PAHs than the latter, suggesting that the burning temperature obviously affects the emitting amount of particulate PAHs, but only slightly influences the PAHs components; and (3) the ratios of benzo[b]fluoranthene/acenaphthylene, benzo[b]fluoranthene/fluorene, dibenzo[a,h]anthracene/acenaphthylene, dibenzo[a,h]anthracene/fluorine, and benzo[b]fluoranthene/benzo[k]fluoranthene in carbonaceous aerosols are sensitively dependent on their sources, indicating that these ratios are suitable for use as characteristic factors or signatures of particulate PAHs in the atmosphere.     

Successful Treatment of Low PAH-Contaminated Sewage Sludge in Aerobic Bioreactors (7 pp) *

Background, Aims and Scope Polycyclic Aromatic Hydrocarbons (PAHs) are known for their adverse and cumulative effects at low concentration. In particular, the PAHs accumulate in sewage sludge during wastewater treatment, and may thereafter contaminate agricultural soils by spreading sludge on land. Therefore, sludge treatment processes constitute the unique opportunity of PAH removal before their release in the environment. In this study, the ability of aerobic microorganisms to degrade light and heavy PAHs was investigated in continuous bioreactors treating trace-level PAH-contaminated sludge. Methods Several aerobic reactors were operated under continuous and perfectly mixed conditions to simulate actual aerobic sludge digesters. Three sterile control reactors were performed at 35°C, 45°C or 55°C to assess PAH abiotic losses under mesophilic and thermophilic conditions. Three biological reactors were also operated at 35°C, 45°C or 55°C. Furthermore, 250 mM methanol were added in an additional mesophilic reactor (35°C). All reactors were fed with long-term PAH-contaminated sewage sludge, and PAH removal was assessed by inlet/outlet mass balance. In this study, PAH compounds ranged from 2 to 5-unsubstituted aromatic rings, i.e. respectively from Fluorene to Indeno(123cd)pyrene. Results and Discussion Significant abiotic losses were observed for the lightest PAHs (fluorene, phenanthrene and anthracene), while biodegradation occurred for all PAHs. More than 80% of the lightest PAHs were removed. Biodegradation rates inversely correlated with the increasing molecular weight, and seemed limited by the low bioavailability of the heaviest PAHs (only 50% of removal). The enhancement of PAH bioavailability by increasing the process temperature or adding methanol was tested. A temperature increase from 35°C to 45°C and then to 55°C significantly enhanced the biodegradation of the heaviest PAHs from 50% to 80%. However, high abiotic losses were observed for all PAHs at 55°C, which was attributed to volatilization. Optimal conditions were found at 45°C considering the low abiotic losses and the high PAH biodegradation rates. Similar performances were achieved by addition of methanol in the sludge. It was concluded that increasing temperatures or addition of methanol favored PAH diffusion from solids to an aqueous compartment, and enhanced their bioavailability to PAH-degrading microorganisms. Conclusion In this study, the use of long-term acclimated aerobic ecosystems showed the high potential of aerobic microorganisms to degrade a wide range of PAHs at trace levels. However, PAH biodegradation was likely controlled by their low bioavailability. Two aerobic processes have been finally proposed to achieve efficient decontamination of sewage sludge, at 45°C or in the presence of methanol. The PAH concentrations in reactor outlet were lower than the French requirements, and allow the treated sludge to be spread on agricultural land. Recommendations and Outlook The two proposed aerobic processes used physical or chemical diffusing agents. The global ecological impact of using the latter agents for treating trace level contamination must be considered. Since methanol was completely removed during the process, no additional harm is expected after treatment. However, an increase of temperature to 45°C could drastically increase the energy demand in full-scale plants, and therefore the ecological impact of the process. Moreover, since bioavailability controls PAH biodegradation, efficiency of the processes could also be influenced by the hydraulic parameters, such as mixing and aeration rates. Further experimentations in a pilot scale are therefore recommended, as well as a final assessment of the global environmental benefit of using such aerobic processes in the bioremediation of trace level compounds. - Abbreviations (PAHs): Ant – anthracene; B(a)A – benzo(a)anthracene ; B(b)F – benzo(b)fluoranthene; B(k)F – benzo(k)fluoranthene; B(ghi)P – benzo(g,h,i)perylene; B(a)P – benzo(a)pyrene; Chrys – chrysene; DB – dibenzo(a,h)anthracene; Fluor – fluoranthene; Fluo - fluorene; Ind – indeno(1,2,3-c,d)pyrene; Phe - phenanthrene; Pyr – pyrene - * The basis of this peer-reviewed paper is a presentation at the 9th FECS Conference on 'Chemistry and Environment', 29 August to 1 September 2004, Bordeaux, France.     

Benzo[b]fluoranthene,a Potential Alternative to Benzo[a]pyrene as an Indicator of Exposure to Airborne PAHs in the Vicinity of Söderberg Aluminum Smelters

ABSTRACT

Benzo[b]fluoranthene (B[b]F) was used in relative abundance ratios (RARs), a parameter obtained by dividing the concentration of individual polycyclic aromatic hydrocarbons (PAHs) found in a given sample by the concentration of B[b]F in the same sample. The B[b]F RARs were derived for PAH concentrations measured at stacks and sampling stations in the vicinity of two Söderberg aluminum horizontal stud smelters (HSSs). The samples collected were analyzed by high-performance liquid chromatography using UV and fluorescence detection. A total of 15 PAHs were analyzed, but, due to the inefficiency of the sampling method used in collecting gaseous PAHs, only particulate PAHs were considered. Comparisons between the B[b]F RARs obtained simultaneously at the source (stack) and those obtained at sampling stations at the two smelters showed that B[b]F degrades more slowly than or at the same rate as most other particulate PAHs monitored. Twenty-three months of urban sampling in the vicinity of one of the aluminum HSSs are also presented, and the results indicate that B[b]F is more stable than all other particulate PAHs investigated. Sampling conducted during a smelter shutdown period confirmed that B[b]F was a much better marker of this source than was benzo[a]pyrene (B[a]P), the usual indicator. The remarkable stability of the benzo[k]fluoranthene (B[k]F)/B[b]F ratio is also discussed.     

Bioaccumulation of cyclopenta[cd]pyrene and benzo[ghi]fluoranthene by mussels transplanted in a coastal lagoon

The bioaccumulation of two isomeric non-alternant non-priority polycyclic aromatic hydrocarbons (PAHs), namely cyclopenta[cd]pyrene and benzo[ghi]fluoranthene, was investigated in caged mussels (Mytilus galloprovincialis) exposed for 30 days in three sites of a coastal lagoon (Pialassa Baiona, Ravenna, Italy) contaminated by pyrogenic PAHs. The concentration of cyclopenta[cd]pyrene and benzo[ghi]fluoranthene increased from undetectable levels in reference mussels withdrawn from the Adriatic sea to 10-30 ng g(-1) dry weight in transplanted mussels. Other contaminants bioaccumulated by caged mussels included pyrene, fluoranthene and mercury. Whilst the isomer concentration ratio pyrene/fluoranthene in biota was comparable to that observed in sediments, the cyclopenta[cd]pyrene/benzo[ghi]fluoranthene ratio was much lower in mussels than in sediments. The lower sediment biota accumulation factor of cyclopenta[cd]pyrene with respect to that of benzo[ghi]fluoranthene was tentatively attributed to the greater biological activity of the former compound, which contains a reactive olefinic bond in the cyclopenta fused ring moiety. Given the higher mutagenic activity of cyclopenta[cd]pyrene with respect to other priority PAHs, its bioaccumulation from contaminated sediments may rise considerably the overall toxicity of PAH residues in exposed biota.     

Polycyclic aromatic hydrocarbons in the sediments of the South China Sea

Sixteen sediment samples, collected from the South China Sea, were analyzed for 11 parent polycyclic aromatic hydrocarbons (PAHs) using gas chromatography and gas chromatography-mass spectrometry. Total concentrations of the 11 PAHs studied in the sediments ranged from 24.7 to 275.4 ng/g with a mean of 145.9 ng/g dry sediment. PAH concentrations displayed a consistent distribution trend with the sediment organic carbon content. The linear regression analysis showed that the total concentration of PAHs in the sediment was significantly correlated to the sediment organic carbon content with a correlation coefficient of 0.735 (n=16). Special PAH compound ratios, such as phenanthrene/anthracene and fluoranthene/pyrene, were calculated to evaluate the relative importance of different origins. The collected data showed that pyrolytic input from anthropogenic combustion processes was predominant at almost all the stations investigated. Only one station, located in the proximity of oil wells, appeared to be contaminated predominantly by petrogenic input. Three anthropogenic PAHs, i.e. pyrene, benzo[a]pyrene and benzo[e]pyrene, exhibited similar distribution patterns in the studied area, implying that these compounds possess identical sources. However, perylene did not entirely follow the distribution trend of the three PAHs, suggesting that the sediment perylene probably derived from other sources such as in situ biogenic origins. Dibenzothiophene, a sulfur heterocyclic aromatic compound, was also measured in this study.     

Hydrocarbon deposition and soil microflora as affected by highway traffic.

The proximity of a busy highway (90,000 vehicles/day) increased the amount of polycyclic aromatic hydrocarbons (PAHs) in soil at the depth of 5-15 cm from 106 ng/g as a grassland background to 3095 ng/g dry soil at the highway verge (a sum of 10 PAH species). The PAH concentration was related to the distance from the source and exhibited a biphasic character, which is interpreted in terms of bimodal distribution of the exhaust microparticles with different rates of deposition. Similarly, the tendency of benz(a)anthracene, chrysene, benzo(b)fluoranthene, benzo(k)fluoranthene, and indeno(1,2,3-cd)pyrene to decrease their proportion with distance from the highway, in contrast to phenanthrene, fluoranthene, pyrene, benzo(a)pyrene, and benzo(g,h,i)perylene, was attributed to their prevalent localisation on the heavier particle fraction. The abundance of bacteria (8.33 x background) and fungi (3.17 x background) close to the highway is thought to be a consequence of hydrocarbon deposition from the traffic that serves as a significant energetic input into the soil. The elevated concentrations of hydrocarbon substrates, as indicated by PAHs, increased both the absolute and relative numbers of the microbial degraders of diesel fuel, biphenyl, naphthalene, and pyrene. Their maximum numbers at 0.5-1.5 m from the pavement reached 1.3 x 10(4), 1.2 x 10(5), 1.1 x 10(4), and 6.6 x 10(3) colony-forming units (CFU) or infection units per gramme dry soil, respectively. On the other hand, the number of anthracene degraders (1.1 x 10(3) CFU per g dry soil) remained close to the detection limit of the enumeration technique used (0.1-0.2 x 10(3) per g dry soil), consistently with the absence of anthracene and higher linear PAHs in the investigated soil samples. The amounts of persisting PAHs justify artificial inoculation with effective degrader strains in the vicinity of motorways.