污水处理厂各工艺阶段多环芳烃变化规律研究

采用固相萃取-气相色谱/氢火焰离子化检测器联用技术(SPE-GC/FID),对西安市某污水处理厂不同工艺段水体中的16种多环芳烃(PAHs)含量进行了长期监测。结果表明,原水中有13种PAHs检出,按浓度从大到小排序分别为:萘、菲、芴、芘、艹屈、二氢苊、苊、蒽、苯并(a)蒽、荧蒽、苯并(b)荧蒽、苯并(k)荧蒽、苯并(a)芘;原水中PAHs的总量在477.1~3 067.7 ng/L之间,平均值为1 833.1 ng/L,同国内外报道的结果相比,可认为西安市生活污水中PAHs的含量处于中等水平;二级处理工艺对PAHs有较好的去除效果,平均去除率为79%,其中,生物处理单元的贡献最大,去除率达到68%。     

盐环境下降解菌群对芘的降解特性研究

以芘为多环芳烃(PAHs)的代表物,利用1.0%盐度的无机盐培养基从石油污染土壤中富集出高效嗜盐PAHs降解菌群。通过DNA测序鉴定,菌群中对芘起重要降解作用的是Rhodanobacter、Pseudomonas、Mycobacterium,3者碱基比例达到31.82%。14d内,萘、菲、荧蒽、芘、苯并[a]芘5种PAHs的挥发损耗均可忽略不计。筛选得到的菌群降解芘的最佳条件为:酵母粉质量浓度为120mg/L,盐度不超过1.0%,无需额外添加甲基-β-环糊精。筛选出的降解菌群对芘的最佳降解条件可用于降解萘、菲、荧蒽和苯并[a]芘等其他PAHs,但随着PAHs环数增加,分子量增大,降解率降低。在最佳条件下降解14d时,萘、菲、荧蒽、芘、苯并[a]芘5种PAHs的降解率可分别达100.00%、85.48%、51.92%、56.28%、50.45%。     

江苏盐城滩涂土壤中多环芳烃的测定

文中采用江苏盐城滩涂响水到滨海一带的滩涂土壤样品,利用索氏提取法提取、硅胶柱净化、高效液相色谱法分离检测土壤样品中的多环芳烃(PAHs),并用优化洗脱程序对滩涂土壤中PAHs的含量进行了测定。结果表明:11个滩涂土壤样品中检出萘、苊烯、菲、蒽、荧蒽、芘六种PAHs,其含量较低,说明该段滩涂土壤尚未受到多环芳烃的污染。     

一株多环芳烃降解菌的筛选及其降解特性

微生物修复是治理土壤多环芳烃(polycyclic aromatic hydrocarbons, PAHs)污染的主要方法,而高效降解菌筛选是微生物修复技术的重要基础。从北京焦化厂土壤中筛选分离得到一株PAHs降解菌Q3,通过生理生化和16S rDNA等分析手段鉴定其为Rhodococcus rhodochrous。结果表明:该菌株对芘的耐受能力较强,可降解初始浓度为200 mg·L~(-1)的芘;该菌株具有降解广谱性,可利用苯并[a]芘、苯并[b]荧蒽、二苯并[a,h]蒽、苯并[g,h,i]苝等9种PAHs为唯一碳源进行代谢,特别是对苯并[a]芘等高环PAHs具有较好的降解效果;此外,该菌株可有效降解模拟液中的混合PAHs,并且对野外被PAHs长期污染的土壤具有较好的强化修复效果。投加菌株处理后的处理组与对照组相比,土壤PAHs总去除率提高了24%。以上结果表明该菌株对环境中被PAHs污染的土壤具有较好的强化修复潜力,可为PAHs污染土壤的微生物修复技术提供技术参考。     

固废拆解场污染土壤中多环芳烃降解菌的筛选鉴定与降解特性

以腐植酸(HA)溶液为吸附剂、从受多环芳烃污染的土壤中分离出来的降解菌制成为生物修复剂,以多环芳烃(PAHs)萘、菲、芘、荧蒽、苯并蒽、苯并芘为土壤污染物,对PAHs污染土壤进行修复实验。目的是筛选与分离吸附于HA的PAHs降解菌,研究HA与降解菌的协同效应对PAHs的降解效率的影响。用经过HA吸附的PAHs富集分离培养出1株高效降解菌株,命名为Tzyx3,鉴定其为解脂耶氏酵母菌(Yarrowia lipolytica)。15 d后,土壤中萘、菲、芘、荧蒽、苯并蒽、苯并芘的降解率分别为90.7%、91.0%、74.7%、86.9%、84.7%和74.7%,表明Tzyx3和HA在PAHs污染土壤中存在协作关系,Tzyx3能够直接利用HA对土壤中的多环芳烃进行降解。     

不同浓度鼠李糖脂对土壤多环芳烃去除率及微生物群落结构的影响

研究了鼠李糖脂浓度对3种多环芳烃(PAHs)菲、荧蒽和芘去除率的影响,以及对土壤微生物群落结构的影响。结果表明,培养35d后,鼠李糖脂质量浓度为100～200mg/kg时,菲、荧蒽和芘的去除率相对最高,土壤中细菌16SrRNA基因和phnAc基因的丰度也达到最大。土壤中天然的PAHs降解菌群主要是假单胞菌属(Pseudomonas)、芽孢杆菌属(Bacillus)、鞘氨醇单胞菌属(Sphingomonas)、溶杆菌属(Lysobacter)和环脂酸芽孢杆菌属(Tumebacillus)等;加入鼠李糖脂后,赭黄嗜盐囊菌属(Haliangium)和土壤红杆菌属(Solirubrobacter)的丰度增加,促进了PAHs更高效的降解。     

某电子垃圾拆解园周边农田土壤中多环芳烃的污染特征及风险评估

研究了某电子垃圾拆解园周边151个农田土壤样品中16种多环芳烃(PAHs)的污染特征和环境风险。结果表明,125个表层土壤样品中PAHs总质量浓度在149.0~2.0×104μg/kg,均值为1 805.5μg/kg,随着剖面土壤深度增加,PAHs含量总体呈递减趋势。通过来源解析,电子拆解园周围土壤中PAHs污染主要由废弃的电子电器元件的粗放燃烧和汽车尾气排放共同引起。土壤风险评估表明,7种类二噁英毒性PAHs的毒性当量(TEQPAH)在6.000×10-5~0.689pg TEQ/g,平均值为0.015pg TEQ/g;苯并(a)芘、二苯并(a,h)蒽、苯并(a)蒽、苯并(b)荧蒽、茚并(1,2,3-cd)芘致癌风险率超出百万分之一的样本比例分别为20.53%、6.62%、1.99%、2.65%、2.65%,其中采样点1、68两个点位表层土壤的苯并(b)荧蒽致癌风险率超过了万分之一。     

类Fenton试剂氧化降解土壤中PAHs及其影响因素研究

使用类Fenton试剂可以有效降解土壤中的多环芳烃（PAHs）。选择4种PAHs菲、芘、苯并[a]芘、茚并（1,2,3-cd）芘作为考察对象,研究了类Fenton试剂对土壤中PAHs的降解条件。单因素降解实验结果表明,在H2O2浓度为0.5mol/L,Fe（NO3）3浓度为0.1 mol/L,水土比为3∶1,反应时间为...     

菌源对多环芳烃降解菌的筛选及降解性能的影响

高效降解菌的筛选对利用生物修复技术有效去除环境中的多环芳烃具有重要意义。分别以石油污染土壤和焦化废水活性污泥为菌源,分离出芘降解菌和混合PAHs(菲、荧蒽和芘)降解菌共14株并对其降解性能进行对比研究。结果表明,筛选得到的菌株分别属于9个菌属,其中2种菌源共有的菌属为Mycobacterium sp.、Ralstonia sp.和Shinella sp.。芘和PAHs的高效降解菌(CP16和CM32)均属于分支杆菌属(Mycobacterium),来源于焦化废水活性污泥;菌株CP16对芘(50mg/L)的7 d降解率为74.99%,CM32对PAHs(菲50 mg/L、荧蒽和芘各10 mg/L)的7 d降解率为100%。因此,以焦化废水活性污泥为菌源更有利于获得高效的多环芳烃降解菌。     

醇类淋洗剂淋洗修复多环芳烃污染土壤

异位土壤淋洗技术是一种有效的污染土壤修复技术。以菲和苯并[a]芘为目标污染物,选取醇类作为淋洗剂,考察了醇种类及浓度、淋洗剂用量、淋洗时间、淋洗温度、淋洗次数对污染土壤(菲和苯并[a]芘质量浓度分别为82.5、4.3mg/kg)淋洗效果的影响。结果表明:修复的最佳条件为正丙醇体积分数40%、淋洗剂用量20mL、淋洗温度20℃、淋洗时间60min、重复淋洗2次,此时菲和苯并[a]芘的去除率分别达到93.05%、86.85%。     

GC/MS analysis of polynuclear aromatic hydrocarbons in sediment samples from the Niger Delta region

Thirteen sediment samples from different locations in the Niger Delta region of Nigeria were analyzed for the presence of 16 polynuclear aromatic hydrocarbons (PAHs) via gas chromatography/mass spectrometry. The specific target compounds for this study included naphthalene, acenaphthylene, acenaphthene, flourene, phenanthrene, anthracene, flouranthene, pyrene, benz[a]anthracene, chrysene, benzo[b]fluoranthene, benzo[k]flouranthene, benzo[a]pyrene, benzo[ghi]perylene, dibenz[a,h]anthracene, and indeno[1,2,3-cd]pyrene. Four isotopically labeled polynuclear aromatic hydrocarbons (acanaphthene-d10, phenanthrene-d10, chrysene-d12 and perylene-d12) were used for internal standardization. All 16 PAHs were found in most of the thirteen samples with concentration ranging from 0.1 microg/kg to 28 microg/kg. It was also found that the 5 and 6-ring PAHs were present in higher concentrations than all the other compounds, indicating their high resistance to microbial degradation.     

Chemical characterization and source identification of polycyclic aromatic hydrocarbons in aerosols originating from different sources

To obtain the characteristic factors or signatures of particulate polycyclic aromatic hydrocarbons (PAHs) to help identify the sources of particulate PAHs in the atmosphere, different carbonaceous aerosols were generated by burning different fossil fuels and biomass under different conditions in the laboratory, and the chemical characteristics of 14 PAHs were studied in detail. The results showed that (1) carbonaceous aerosols derived from domestic burning of coal, diesel fuel, and gasoline have much higher concentrations of PAHs than those derived from domestic burning of biomass; (2) carbonaceous aerosols derived from domestic burning of diesel fuel/gasoline have similar PAH components as those derived from high-temperature combustion of diesel fuel/gasoline, although the former have much higher concentrations of PAHs than the latter, suggesting that the burning temperature obviously affects the emitting amount of particulate PAHs, but only slightly influences the PAHs components; and (3) the ratios of benzo[b]fluoranthene/acenaphthylene, benzo[b]fluoranthene/fluorene, dibenzo[a,h]anthracene/acenaphthylene, dibenzo[a,h]anthracene/fluorine, and benzo[b]fluoranthene/benzo[k]fluoranthene in carbonaceous aerosols are sensitively dependent on their sources, indicating that these ratios are suitable for use as characteristic factors or signatures of particulate PAHs in the atmosphere.     

PCDD/F, PAH and heavy metals in the sewage sludge from six wastewater treatment plants in Beijing, China

In order to better understand land application of sewage sludge, the characterization of heavy metals, PCDD/F and PAHs in sewage sludge was investigated from six different wastewater treatment plants (WWTP) in Beijing City, China. It was found that the total concentrations of Zn in Wujiacun (WJC) sewage sludge, and Cd and Hg in sewage sludge generated from all of the six different places are higher than Chinese regulation limit of pollutants for sludge to be used for agriculture (GB18918-2002). The levels of 16 PAHs that have been categorized as priority pollutants by US EPA in the sewage sludge samples varied from 2467 to 25923 microg/kg (dry weight), the highest values of 25923 microg/kg being found in WJC WWTP. The concentrations of Benzo[a]pyrene were as high as 6.1mg/kg dry weight in WJC sewage sludge, exceeding the maximum permitted content by GB18918-2002. Individual PAH content varies considerably with sewage samples. The ratios of anthracene to anthracene plus phenanthrene (An/178), benz[a]anthracene to benz[a]anthracene plus chrysene (BaA/228), indene[1,2,3-cd]pyrene to indene[1,2,3-cd]pyrene plus benzo[g,h,i]perylene (In/In+BP), and fluoranthene to fluoranthene plus pyrene (Fl/Fl+Py) suggest that petroleum and combustion of fossil fuel were the dominant contributions for the PAHs in sewage sludge. The concentrations of total PCDD/F in the sewage sludge ranged from 330 to 4245 pg/g d.w. The toxicity equivalent concentrations is between 3.47-88.24 pg I-TEQ according to NATO/CCMS, which is below Chinese legislation limit value proposed for land application. The PCDD/F congener/homologue profiles found in the Beijing samples indicated that the high chlorinated PCDD/F contamination might originate mainly from PCP-related source and depositional sources while the low chlorinated PCDD/F homologues could be originating from incineration or coal combustion. The major source of PCDD/Fs in Beijing sludge is still unclear.     

Contamination of polycyclic aromatic hydrocarbons (PAHs) in microlayer and subsurface waters along Alexandria coast,Egypt

The residues of seven polycyclic aromatic hydrocarbons (PAHs) pollutants in microlayer and subsurface seawater samples collected from Alexandria coast, Egypt, were analyzed by gas chromatography–electron-impact mass spectrometry-selected ion monitoring mode (GC–MS-SIM). The pollutants studied were, fluorene, phenanthrene, anthracene, fluoranthene, pyrene, chrysene and benzo[a]pyrene. Total PAH levels in microlayer ranged from 103 to 523 ng/l, while it ranged in subsurface samples from 13 to 120 ng/l. The Western Harbor location recorded the highest level of PAHs pollutant over all the other location for both subsurface and microlayer waters. The two major PAHs in microlayer water at the Western Harbor were fluorene and phenanthrene, making up 27% and 20% of the total PAHs, while the two major PAHs in subsurface water at the Eastern Harbor were phenanthrene and fluoranthene recording up 21% each of the total PAHs. The total PAH levels were generally in the nano-gram per liter for microlayer and subsurface seawater samples. The dominant PAHs in both subsurface and microlayer samples were fluoranthene, pyrene and benzo[a]pyrene. The microlayer enrichment factor at Alexandria’s Mediterranean coast was ranged from 29 for fluorene to 3 for phenanthrene and benzo[a]pyrene which showed PAHs concentration in the microlayer with an average of five times more than the total PAH in the subsurface samples.     

Occurrence and assessment of polycyclic aromatic hydrocarbons in soils from vegetable fields of the Pearl River Delta, South China

Surface soil (0-20 cm) samples from nine representative vegetable fields located in Guangzhou, Shenzhen, Zengcheng and Huadu within the Pearl River Delta, South China were collected and analyzed for 16 USEPA priority polycyclic aromatic hydrocarbons (PAHs) using gas chromatography coupled to mass spectrometry (GC-MS). Total concentrations of 16 PAHs (Sigma(PAHs)) ranged from 160 to 3700 microg kg(-1). Large variations were observed also between concentrations of individual PAHs from different vegetable fields and within the site as well. Acenapthylene, benzo[b]fluoranthene, fluoranthene, benzo[a]pyrene and benzo[k]fluoranthene were consistently the most prevalent individual PAHs. The values of PAH isomer ratios [anthracene/(anthracene+phenanthrene) and fluoranthene/(fluoranthene+pyrene)] indicate that combustion processes are the major sources of PAHs. Concentrations of PAHs were poorly correlated with organic carbon concentrations of soils, suggesting different sources and also indicating that the PAH pollution of this area is recent. The same outcome is confirmed by the predominance of PAHs with fewer rings (相似文献   

Leaves of Quercus ilex L. as biomonitors of PAHs in the air of Naples (Italy)

Polycyclic aromatic hydrocarbons (PAHs) were determined by the GC-MS chromatography in the leaves of Quercus ilex L., an evergreen Mediterranean oak, to monitor the degree of pollution in the urban area of Naples compared to remote areas. Leaf samples were collected in July 1998 from four urban parks, six roadsides and two sites in remote areas. The total PAH contents in Q. ilex leaves ranged from 106.6 in a control site to 4607.5 ng/g d.w. along a road with a high traffic flow. The mean concentration factors (urban/control) were 3.8 for the parks and 15 for the roads. The contribution of carcinogenic PAHs (benz[a]anthracene, benzo[b]fluoranthene, benzo[k]fluoranthene, benzo[a]pyrene, dibenz[a,h]anthracene, indeno[1,2,3-c,d]pyrene) was higher in urban area and differed according to the site, ranging from 6.7% to 21.3%. The total PAH burden in control sites was dominated by the low molecular weight PAHs, whilst along the urban roads fluoranthene, pyrene and benz[a]anthracene among the measured PAHs showed the highest values. PAHs were positively correlated (P<0.01) to trace metals measured in a previous study.     

Studies on polycyclic aromatic hydrocarbons in two sediment cores from the huaxi reservoir,china: Assessment of levels,sources, and ecological risk

This study investigated the levels, sources and ecological risks of 16 polycyclic aromatic hydrocarbons (PAHs) in two sediment cores that were collected along the Huaxi Reservoir. The spatial distributions and residue levels of the 16 priority PAHs in the sediments from the Huaxi Reservoir were analyzed for their potential ecological risk, source apportionment and contribution to the total PAH residue. The concentration level of the total PAHs (TPAHs) was in the range 1805 ng·g^?1 to 20023 ng·g^?1 based on dry weight, and the content of PAHs in the Huaxi Reservoir exhibited a gradual upward trend. The PAH congener ratios fluoranthene/(fluoranthene + pyrene) and indeno[1, 2, 3-cd]pyrene/(indeno[1, 2, 3-cd]pyrene + benzo[g, h, i]perylene) were used to identify the source. The main source of the low molecular weight PAHs was wood and coal combustion, whereas the high molecular weight PAHs were primarily from petroleum combustion sources. The results of an ecological risk assessment demonstrated that ACE poses a potential ecological risk, while FLU, NAP, ANT, BaP, DBA, PHEN and PYR can have serious ecological risks.     

Bioaccumulation of cyclopenta[cd]pyrene and benzo[ghi]fluoranthene by mussels transplanted in a coastal lagoon

The bioaccumulation of two isomeric non-alternant non-priority polycyclic aromatic hydrocarbons (PAHs), namely cyclopenta[cd]pyrene and benzo[ghi]fluoranthene, was investigated in caged mussels (Mytilus galloprovincialis) exposed for 30 days in three sites of a coastal lagoon (Pialassa Baiona, Ravenna, Italy) contaminated by pyrogenic PAHs. The concentration of cyclopenta[cd]pyrene and benzo[ghi]fluoranthene increased from undetectable levels in reference mussels withdrawn from the Adriatic sea to 10-30 ng g(-1) dry weight in transplanted mussels. Other contaminants bioaccumulated by caged mussels included pyrene, fluoranthene and mercury. Whilst the isomer concentration ratio pyrene/fluoranthene in biota was comparable to that observed in sediments, the cyclopenta[cd]pyrene/benzo[ghi]fluoranthene ratio was much lower in mussels than in sediments. The lower sediment biota accumulation factor of cyclopenta[cd]pyrene with respect to that of benzo[ghi]fluoranthene was tentatively attributed to the greater biological activity of the former compound, which contains a reactive olefinic bond in the cyclopenta fused ring moiety. Given the higher mutagenic activity of cyclopenta[cd]pyrene with respect to other priority PAHs, its bioaccumulation from contaminated sediments may rise considerably the overall toxicity of PAH residues in exposed biota.     

Quantification and characterization of vehicle-based polycyclic aromatic hydrocarbons (PAHs) in street dust from the Tamale metropolis,Ghana

Objective

Concentrations of polycyclic aromatic hydrocarbons (PAHs) in street dust in the Tamale metropolis, Ghana, have been measured in this study.

Results

The concentrations of the various types of PAHs identified in street dust samples from high vehicular traffic density in the metropolis are as follows: naphthalene, 10,000 μg/kg; acenaphthylene, 13,000 μg/kg; acenaphthene, 76,000 μg/kg; fluorene, 18,900 μg/kg; phenanthrene, 40,000 μg/kg; anthracene, 21,000 μg/kg; fluoranthene, 35,200 μg/kg; pyrene, 119,000 μg/kg; benzo[a]anthracene, 17,700 μg/kg; chrysene, 10,600 μg/kg; benzo[k]fluoranthene, 18,700 μg/kg; benzo[a]pyrene, 10,900 μg/kg and benzo[g, h, i]perylene, 21,000 μg/kg. Calculation of the phenanthrene/anthracene ratio indicated that the PAHs identified in this study were from vehicular fallout as the ratio was less than 10.

Conclusion

It is clear from the results of the study that road users in the Tamale metropolis, especially hawkers, are exposed to the harmful effects of PAHs, and this suggests the need for the establishment of mitigation measures by the regulatory agencies.

     

Profiles of PAH emission from steel and iron industries

In order to characterize the polycyclic aromatic hydrocarbons (PAHs) emission from steel and iron industries, this study measured the stack emission of twelve steel and iron plants in southern Taiwan to construct a set of source fingerprints. The study sampled the emissions by the USEPA's sampling method 5 with the modification of Graseby for the gas and particulate phase PAH and, then, used Hewlett-Packard 5890 gas chromatograph equipped with mass spectrometer detector to analyze the samples. The steel and iron industries are classified into three categories on the basis of auxiliary energy source: Category I uses coal as fuel, Category II uses heavy oil as fuel and Category III uses electric arc furnace. The pollution source profiles are obtained by averaging the ratios of individual PAH concentrations to the total concentration of 21 PAHs and total particulate matter measured in this study. Results of the study show that low molecular weight PAHs are predominant in gas plus particulate phase for all three categories. For particulate phase PAHs, however, the contribution of large molecular weight compounds increases. Two-ring PAHs account for the majority of the mass, varying from 84% to 92% with an average of 89%. The mass fractions of 3-, 4-, 5-, 6-ring PAHs in Category I are found to be more than those of the other two categories. The mass of Category III is dominated by 7-ring PAHs. Large (or heavy) molecular weight PAHs (HMW PAHs) are carcinogenic. Over all categories, these compounds are less than 1% of the total-PAH mass on the average. The indicatory PAHs are benz[a]anthracene, benzo[k]fluoranthene, benzo[ghi]perylene for Category I, benzo[a]pyrene, acenaphthene, acenaphthylene for Category II and coronene, pyrene, benzo[b]chrycene for Category III. The indicatory PAHs among categories are very different. Thus, dividing steel and iron industry into categories by auxiliary fuel is to increase the precision of estimation by a receptor model. Average total-PAH emission factors for coal, heavy oil and electric arc furnace were 4050 μg/kg-coal, 5750 μg/l-oil, 2620 μg/kW h, respectively. Carcinogenic benzo[a]pyrene for gas plus particulate phase was 2.0 g/kg-coal, 2.4 μg/l-oil and 1.4 μg/kW h for Category I, II and III, respectively.