Partitioning gas tracer tests for measurement of water in municipal solid waste

A key component in the operation of almost all bioreactor landfills is the addition of water to maintain optimal moisture conditions. To determine how much water is needed and where to add it, in situ methods are required to measure water within solid waste. Existing technologies often result in measurements of unknown accuracy, because of the variability of solid waste materials and time-dependent changes in packing density, both of which influence most measurement methods. To overcome these problems, a new technology recently developed by hydrologists for measuring water in the vadose zone--the partitioning gas tracer test--was tested. In this technology, the transport behavior of two gas tracers within solid waste is used to measure the fraction of the void space filled with water. One tracer is conservative and does not react with solids or liquids, while a second tracer partitions into the water and is separated from the conservative tracer during transport. This technology was tested in four different solid waste packings and was capable of determining the volumetric water content to within 48% of actual values, with most measurement errors less than 15%. This technology and the factors that affect its applicability to landfills are discussed in this paper.     

Effect of biogas generation on radon emissions from landfills receiving radium-bearing waste from shale gas development

Dramatic increases in the development of oil and natural gas from shale formations will result in large quantities of drill cuttings, flowback water, and produced water. These organic-rich shale gas formations often contain elevated concentrations of naturally occurring radioactive materials (NORM), such as uranium, thorium, and radium. Production of oil and gas from these formations will also lead to the development of technologically enhanced NORM (TENORM) in production equipment. Disposal of these potentially radium-bearing materials in municipal solid waste (MSW) landfills could release radon to the atmosphere. Risk analyses of disposal of radium-bearing TENORM in MSW landfills sponsored by the Department of Energy did not consider the effect of landfill gas (LFG) generation or LFG control systems on radon emissions. Simulation of radon emissions from landfills with LFG generation indicates that LFG generation can significantly increase radon emissions relative to emissions without LFG generation, where the radon emissions are largely controlled by vapor-phase diffusion. Although the operation of LFG control systems at landfills with radon source materials can result in point-source atmospheric radon plumes, the LFG control systems tend to reduce overall radon emissions by reducing advective gas flow through the landfill surface, and increasing the radon residence time in the subsurface, thus allowing more time for radon to decay. In some of the disposal scenarios considered, the radon flux from the landfill and off-site atmospheric activities exceed levels that would be allowed for radon emissions from uranium mill tailings.

Implications: Increased development of hydrocarbons from organic-rich shale formations has raised public concern that wastes from these activities containing naturally occurring radioactive materials, particularly radium, may be disposed in municipal solid waste landfills and endanger public health by releasing radon to the atmosphere. This paper analyses the processes by which radon may be emitted from a landfill to the atmosphere. The analyses indicate that landfill gas generation can significantly increase radon emissions, but that the actual level of radon emissions depend on the place of the waste, construction of the landfill cover, and nature of the landfill gas control system.     

Polymers as Solid Waste in Municipal Landfills

Abstract

Synthetic polymers reach municipal landfills as components of products such as waste household paints, packaging films, storage containers, carpet fibers, and absorbent sanitary products. Some polymers in consumer products that reach landfills are designed to photodegrade or biodegrade. This article examines the significance of degradable polymers in management of solid waste in municipal landfills. Most landfills are not designed to photodegrade or biodegrade solid waste. Landfill disposal of stable polymers such as polyacrylics and polyethylenes is not associated with significant polymer degradation or mobility. Stability to photodegradation and biodegradation is an advantage when municipal landfills are used for disposal of polymer products as solid waste. Use of landfill disposal can be a responsible means to manage polymer waste and can be part of an overall waste management plan which includes source reduction, recycling, reuse, composting, and waste-to-energy incineration.     

Sewage Sludge to Landfill: Some Pertinent Engineering Properties

Abstract

More stringent controls on the quality of wastewater discharges have given rise to increasing volumes of sewage sludge for disposal, principally to land, using either land-spreading or sludge-to-landfill operations. Current sludge-to-landfill methods generally involve mixing the concentrated sludge with other solid waste in municipal landfills. However, stricter waste disposal legislation and higher landfill taxes are forcing the water industry to look for more efficient disposal strategies. Landfill operators are also increasingly reluctant to accept sludge material in the slurry state because of construction difficulties and the potential for instability of the landfill slopes. The engineering and drying properties of a municipal sewage sludge are presented and applied, in particular, to the design, construction, and performance of sewage sludge monofills. Sludge handling and landfill construction are most effectively conducted within the water content range of 85% water content, the optimum water content for standard proctor compaction, and 95% water content, the sticky limit of the sludge material. Standard proctor compaction of the sludge within this water content range also achieves the maximum dry density of ～0.56 tonne/m³, which maximizes the storage capacity and, hence, the operational life of the landfill site. Undrained shear strength-water content data (pertinent to the stability of the landfill body during construction) and effective stress-strength parameters, which take into account the landfill age and the effects of ongoing sludge digestion, are presented. Landfill subsidence, which occurs principally because of creep and decomposition of the solid organic particles, is significant and continues indefinitely but at progressively slower rates.     

Analysis of Long-Term Settlement of Municipal Solid Waste Landfills as Determined by Various Settlement Estimation Methods

Abstract

In this study, several existing municipal solid waste (MSW) settlement estimation methods are reviewed and applied to analyze the settlement data of nine MSW land-fills. Because a biodegradation-related settlement contributes differently to a long-term total settlement depending on the age of landfills, the actual MSW landfill sites are classified into three groups to specifically address the validity of each method in its prediction of a long-term settlement for each age category. Results demonstrate that there are considerable decreases in predicted settlement potentials as fill age increases. Comparisons indicate that the individual estimation methods display a considerable variation in predicting settlements in the fresh MSW landfills. On the other hand, for the old refuse landfills, all of the estimation methods, except the extended soil model, predict low settlement potentials.     

Greenhouse gas emissions from the waste sector in Argentina in business-as-usual and mitigation scenarios

The objective of this work was the application of 2006 Intergovernmental Panel on Climate Change (IPCC) Guidelines for the estimation of methane and nitrous oxide emissions from the waste sector in Argentina as a preliminary exercise for greenhouse gas (GHG) inventory development and to compare with previous inventories based on 1996 IPCC Guidelines. Emissions projections to 2030 were evaluated under two scenarios—business as usual (BAU), and mitigation—and the calculations were done by using the ad hoc developed IPCC software. According to local activity data, in the business-as-usual scenario, methane emissions from solid waste disposal will increase by 73% by 2030 with respect to the emissions of year 2000. In the mitigation scenario, based on the recorded trend of methane captured in landfills, a decrease of 50% from the BAU scenario should be achieved by 2030. In the BAU scenario, GHG emissions from domestic wastewater will increase 63% from 2000 to 2030. Methane emissions from industrial wastewater, calculated from activity data of dairy, swine, slaughterhouse, citric, sugar, and wine sectors, will increase by 58% from 2000 to 2030 while methane emissions from domestic will increase 74% in the same period. Results show that GHG emissions calculated from 2006 IPCC Guidelines resulted in lower levels than those reported in previous national inventories for solid waste disposal and domestic wastewater categories, while levels were 18% higher for industrial wastewater.

Implications: The implementation of the 2006 IPCC Guidelines for National Greenhouse Inventories is now considering by the UNFCCC for non-Annex I countries in order to enhance the compilation of inventories based on comparable good practice methods. This work constitutes the first GHG emissions estimation from the waste sector of Argentina applying the 2006 IPCC Guidelines and the ad doc developed software. It will contribute to identifying the main differences between the models applied in the estimation of methane emissions on the key categories of waste emission sources and to comparing results with previous inventories based on 1996 IPCC Guidelines.     

非规范生活垃圾填埋场填埋气横向迁移规律及控制

我国城市中尚有大量非规范生活垃圾填埋场存在,对其进行污染整治消除填埋气导致的环境安全隐患刻不容缓.以重庆某垃圾填埋场为例,研究重庆市主城区的非规范生活垃圾填埋场填埋气的横向迁移问题,在垃圾场周边区域布设36个监测井,对监测井中的填埋气进行分析监测,以填埋气特征组分CH4气体的体积浓度变化研究填埋气的横向迁移规律.结果表明,监测井到填埋场边界的距离为监测井中CH4气体浓度的主要影响因素;垃圾场周边距离填埋场场界50 m以外的区域,填埋气的横向迁移已经相当微弱;但是距离填埋场边界50 m以内区域的填埋气的横向迁移明显,需要在距离填埋场边界50 m范围内采取措施与场内填埋气的导排措施配合,进行填埋气的污染控制.     

Methane Emissions from Domestic Waste Management Facilities in Jordan—Applicability of IPCC Methodology

ABSTRACT

In this paper, methane emissions from municipal wastewater treatment plants and municipal solid waste (MSW) landfills in Jordan for 1994 have been estimated using the methodology developed by the Intergovernmental Panel on Climate Change (IPCC). For this purpose, the 14 domestic wastewater treatment plants in the country were surveyed. Generation rates and characterization of MSW components as well as dumping and landfilling practices were surveyed in order to estimate 1994 CH₄ emissions from these sites. Locally available waste statistics were used in cases where those of the IPCC guidelines were not representative of Jordan's statistics.

Methane emissions from domestic wastewater in Jordan were estimated at 4.66 gigagrams (Gg). Total 1994 CH₄ emissions from MSW management facilities in Jordan are estimated at 371.76 Gg—351.12 Gg (94.45%) from sanitary landfills, 19.83 Gg (5.33%) from MSW open dumps, and 0.81 Gg (0.22%) from raw sewage-water dumping ponds. Uncertainties associated with these estimations are presented.     

Permeability test and slope stability analysis of municipal solid waste in Jiangcungou Landfill,Shaanxi, China

With the rapid increase of city waste, landfills have become a major method to deals with municipal solid waste. Thus, the safety of landfills has become a valuable research topic. In this paper, Jiangcungou Landfill, located in Shaanxi, China, was investigated and its slope stability was analyzed. Laboratory tests were used to obtain permeability coefficients of municipal solid waste. Based on the results, the distribution of leachate and stability in the landfill was computed and analyzed. These results showed: the range of permeability coefficient was from 1.0 × 10^–7 cm sec^–1 to 6.0 × 10^–3 cm sec^–1 on basis of laboratory test and some parameters of similar landfills. Owing to the existence of intermediate cover layers in the landfill, the perched water level appeared in the landfill with heavy rain. Moreover, the waste was filled with leachate in the top layer, and the range of leachate level was from 2 m to 5 m in depth under the waste surface in other layers. The closer it gets to the surface of landfill, the higher the perched water level of leachate. It is indicated that the minimum safety factors were 1.516 and 0.958 for winter and summer, respectively. Additionally, the slope failure may occur in summer.

Implications: The research of seepage and stability in landfills may provide a less costly way to reduce accidents. Landslides often occur in the Jiangcungou Landfill because of the high leachate level. Some measures should be implemented to reduce the leachate level. This paper investigated seepage and slope stability of landfills by numerical methods. These results may provide the basis for increasing stability of landfills.     

Non-controlled biogenic emissions to the atmosphere from Lazareto landfill, Tenerife, Canary Islands

GOAL, SCOPE AND BACKGROUND: [corrected] Historically, landfills have been the simplest form of eliminating urban solid waste with the minimum cost. They have been the most usual method for discarding solid waste. However, landfills are considered authentic biochemical reactors that introduce large amounts of contaminants into the environment in the form of gas and leachates. The dynamics of generation and the movement of gas in landfills depend on the input and output parameters, as well as on the structure of the landfill and the kind of waste. The input parameters include water introduced through natural or artificial processes, the characteristics of the urban solid waste, and the input of atmospheric air. The main output parameters for these biochemical reactors include the gases and the leachates that are potentially pollutants for the environment. Control systems are designed and installed to minimize the impact on the environment. However, these systems are not perfect and a significant amount of landfill gas could be released to the atmosphere through the surface in a diffuse form, also known as Non-controlled emission. In this paper, the results of the Non-controlled biogenic gas emissions from the Lazareto landfill in Tenerife, Canary Islands, are presented. The purpose of this study was to evaluate the concentration of CH4 and CO2 in the soil gas of the landfill cover, the CH4 and CO2 efflux from the surface of the landfill and, finally, to compare these parameters with other similar landfills. In this way, a better understanding of the process that controls biogenic gas emissions in landfills is expected. METHODS: A Non-controlled biogenic gas emission survey of 281 sampling sites was carried out during February and March, 2002. The sampling sites were selected in order to obtain a well-distributed sampling grid. Surface landfill CO2 efflux measurements were carried out at each sampling site on the surface landfill together with soil gas collection and ground temperatures at a depth of 30-40 cm.The CH4 efflux was computed from CO2 efflux and from the ratio CH4/CO2 in the soil gas. Soil gas samples were collected at a depth of 30-40 cm using a metallic probe and 20 cc hypodermic syringes, and later stored in evacuated 10 cc vacutainers for laboratory analysis of bulk composition. The gas sample was introduced in a vacutainer filled with deionized water and displacing the water until the vacutainer was filled with the gas sample in order to avoid air contamination from entering. The surface landfill temperature of the landfill was measured at a depth of 40 cm using a digital thermometer type OMEGA 871A. Landfill gases, CO2 and CH4, were analyzed within 24 hours using a double channel VARIAN micro-GC QUAD CP-2002P, with a 10 meter PORAPLOT-Q column, a TCD detector, and He as a carrier gas. The analysis temperature was 40 degrees C and the injection time was 10 msec. Surface landfill CO2 efflux measurements were performed using a portable NDIR spectrophotometer Licor-800 according to the accumulation chamber method (Chiodini et al. 1996). The data treatment, aimed at drawing the flux map and computing the total gas output, was based on the application of stochastic simulation algorithms provided by the GSLIB program (Deutsch and Journel 1998). RESULTS: Diffuse CH4 and CO2 efflux values range from negligible values up to 7,148 and 30,573 g m(-2) d(-1), respectively. The spatial distribution of the concentration and efflux of CO2, CH4 and soil temperature, show three areas of maximum activity in the landfill, suggesting a non-uniform pattern of diffuse degassing. This correlation between high emissions and concentration of CO2, CH4 and soil temperatures suggests that the areas of higher microbial activity and exothermic reactions are releasing CO2 and CH4 to the atmosphere from the landfill. Taking into consideration the spatial distribution of the CO2 and CH4 efflux values as well as the extension of the landfill, the Non-controlled emission of CO2 and CH4 to the atmosphere by the Lazareto's landfill are of 167 +/- 13.3 and 16 +/- 2.5 t d(-1), respectively. DISCUSSION: The patterns of gas flow within the landfill seem to be affected by boundary materials at the sides. The basalt layers have a low permeability and the gas flow in these areas is extensive. In this area, where a basalt layer does not exist, the flow gas diffuses toward the sea and the flux emissions at the landfill surface are lower. This behavior reflects the possible dissolution of gases into water and the deflection of gases towards the surface at the basalt boundary. The proximity to the sea, the installation of a palm tree garden and, as a result, the contribution of water coming from the watering of this garden has reactivated the system. The introduction of sea water into the landfill and the type of boundary could be defining the superficial gas discharges. CONCLUSIONS: Results from this study indicate that the spatial distribution of Non-controlled emission of CO2 and CH4 at the Lazareto's landfill shows a non-uniform pattern of diffuse degassing. The northeast, central and northwest areas of the Lazareto's landfill are the three areas of high emissions and concentration of CO2 and CH4, and high temperatures. The correlation between high emissions and the concentration of CO2, CH4, and the high temperatures suggest that the areas of higher microbial activity and exothermic reactions are releasing more CO2 and CH4 to the atmosphere from the landfill. A high concentration of CO2 is probably due to the presence of methanotrophic bacteria in the soil atmosphere of the landfill. Patterns of gas flow within the landfill seem to be affected by boundary materials (basalt layers) of low permeability, and side boundaries of the flux emissions at the surface are higher. At the sides of seawater and sediment boundaries, flux emissions at the landfill surface are lower. This behavior reflects a possible dissolution of gases into the water and the deflection of gases towards the surface at the basalt boundary. With this study, we can compare the data obtained in this landfill with other landfills and observe the different levels of emission. The proximity to the sea and the installation of the palm tree garden palms and, as a result, the contribution of water coming from the watering of this garden has reactivated the system. Many landfills worldwide located in similar settings could experience similar gas production processes. RECOMMENDATIONS AND PERSPECTIVES: The need for investigating and monitoring sea water and sediment quality in these landfills is advisable. Concentrations and fluxes of contaminants and their impact in the area should be assessed. With this study we can compare the data obtained in these landfills with other landfills and observe the different levels of emission.     

软土地基上生活垃圾卫生填埋场的岩土工程问题与对策

生活垃圾卫生填埋场是处理固体废弃物的有效方法之一.尽管国内外学者对与垃圾填埋场相关的许多问题已经做了大量的研究工作,但是对软土地基上填埋场可能引起的一些岩土工程问题研究不多.针对软土地基上的填埋场,分析了填埋场在建设与运营过程将会遇到的若干岩土工程问题.针对填埋场的沉降、稳定性等问题,提出了将垃圾荷载看作变量对地基沉降进行计算和设计.考虑垃圾体的稳定性,分析由于地基破坏而引起的整体稳定性问题和变形引起的衬里系统的内部稳定性问题,研究地基处理的可行性和适应性,并加强填埋过程中的岩土工程监测工作.     

Advantages and Possibilities of Solid Recovered Fuel Cocombustion in the European Energy Sector

Abstract

The 1999/31 Elemental Carbon Directive sets strict rules on the disposal of untreated municipal solid waste in the European Union countries and forces a reduction of the biodegradable quantities disposed off to landfills up to 35% of the amount produced in 1995 in the coming decade. More environmentally friendly waste management options shall be promoted under the framework of the Community Waste Strategy ([96] 399 Final). In this context, the production and thermal use of solid recovered fuels (SRFs), derived from nonhazardous bioresidues and mixed- and mono-waste streams, could be a key element in a future waste management system. Within the scope of the European Demonstration Project, RECO-FUEL, SRF cocombustion was demonstrated in two large-scale lignite-fired coal boilers at RWE power station in Weisweiler, Germany. As a consequence of the high biogenic share of the cocombusted material, this approach can be considered beneficial following European Directive 2001/77/EC on electricity from renewable energy sources (directive). During the experimental campaign, the share of SRF in the overall thermal input was adjusted to approximately 2%, resulting into a feeding rate of approximately 25 t/hr. The measurement campaign included boiler measurements in different locations, fuel and ash sampling, and its characterization. The corrosion rates were monitored by dedicated corrosion probes. The overall results showed no significant influence of SRF cocombustion on boiler operation, emissions behavior, and residues quality for the thermal shares applied. Also, no effect of the increased chlorine concentration of the recovered fuel was observed in the flue gas path after the desulfurization unit.     

Greenhouse gas emission potential of the municipal solid waste disposal sites in Thailand

Open dumping and landfilling are the prevalent solid waste disposal practices in Thailand. Surveys on the disposal sites revealed the presence of 95 landfills and 330 open dumps. Methane emission potential at these sites was estimated by three methods. Results of the Intergovernmental Panel on Climate Change (IPCC) method, Landfill Gas Emission model (LandGEM), and closed flux chamber technique were compared. The methane emission potential of 366 Gg/yr using the IPCC method was higher than the estimations of the LandGEM and closed flux chamber method of 115 Gg/yr and 103 Gg/yr, respectively. An understanding of the methane emission potential initiated the analysis of upgrading the open dumps into landfills, adding landfills to meet the future needs and utilization of landfill gases. Upgrading the open dumps to landfills increased the methane emission rates and their utilization potential. Approximately 20 additional landfills may be required to meet future demands. Landfill gas (LFG) utilization appears to be feasible in the large-scale landfills.     

Comparing estimates of fugitive landfill methane emissions using inverse plume modeling obtained with Surface Emission Monitoring (SEM), Drone Emission Monitoring (DEM), and Downwind Plume Emission Monitoring (DWPEM)

ABSTRACT

As part of the global effort to quantify and manage anthropogenic greenhouse gas emissions, there is considerable interest in quantifying methane emissions in municipal solid waste landfills. A variety of analytical and experimental methods are currently in use for this task. In this paper, an optimization-based estimation method is employed to assess fugitive landfill methane emissions. The method combines inverse plume modeling with ambient air methane concentration measurements. Three different measurement approaches are tested and compared. The method is combined with surface emission monitoring (SEM), above ground drone emission monitoring (DEM), and downwind plume emission monitoring (DWPEM). The methodology is first trialed and validated using synthetic datasets in a hand-generated case study. A field study is also presented where SEM, DEM and DWPEM are tested and compared. Methane flux during two-days measurement campaign was estimated to be between 228 and 350 g/s depending on the type of measurements used. Compared to SEM, using unmanned aerial systems (UAS) allows for a rapid and comprehensive coverage of the site. However, as showed through this work, advancement of DEM-based methane sampling is governed by the advances that could be made in UAS-compatible measurement instrumentations. Downwind plume emission monitoring led to a smaller estimated flux compared with SEM and DEM without information about positions of major leak points in the landfill. Even though, the method is simple and rapid for landfill methane screening. Finally, the optimization-based methodology originally developed for SEM, shows promising results when it is combined with the drone-based collected data and downwind concentration measurements. The studied cases also discovered the limitations of the studied sampling strategies which is exploited to identify improvement strategies and recommendations for a more efficient assessment of fugitive landfill methane emissions.

Implications: Fugitive landfill methane emission estimation is tackled in the present study. An optimization-based method combined with inverse plume modeling is employed to treat data from surface emission monitoring, drone-based emission monitoring and downwind plume emission monitoring. The study helped revealing the advantages and the limitations of the studied sampling strategies. Recommendations for an efficient assessment of landfill methane emissions are formulated. The method trialed in this study for fugitive landfill methane emission could also be appropriate for rapid screening of analogous greenhouse gas emission hotspots.     

固体废物在固定床式热解炉内热解产气特性的实验研究

垃圾热解技术以其较低的污染排放和较高的能源回收率在固体废弃物处理领域里占有重要地位。利用小型外热型热解炉对城市垃圾、生物质及有害固体废弃物进行热解实验 ,分析发现 ,物料的挥发分、加热方式以及热解终温等对产气影响大 ,随温度的增加产气中H2 含量逐渐增多 ,C2 H4和C2 H6 的含量逐渐下降 ,气体热值有一个最大值。     

Comparison of Aerobic and Anaerobic Biotreatment of Municipal Solid Waste

Abstract

To increase the operating lifetime of landfills and to lower leachate treatment costs, an increasing number of municipal solid waste (MSW) landfills are being managed as either aerobic or anaerobic bioreactors. Landfill gas composition, respiration rates, and subsidence were measured for 400 days in 200-L tanks filled with fresh waste materials to compare the relative effectiveness of the two treatments. Tanks were prepared to provide the following conditions: (1) air injection and leachate recirculation (aerobic), (2) leachate recirculation (anaerobic), and (3) no treatment (anaerobic). Respiration tests on the aerobic wet tank showed a steady decrease in oxygen consumption rates from 1.3 mol/day at 20 days to 0.1 mol/day at 400 days. Aerobic wet tanks produced, on average, 6 mol of carbon dioxide (CO₂)/kg of MSW as compared with anaerobic wet tanks, which produced 2.2 mol methane/kg of MSW and 2.0 mol CO₂/kg methane. Over the test period, the aerobic tanks settled on average 35%, anaerobic tanks settled 21.7%, and the no-treatment tank settled 7.5%, equivalent to overall mass loss in the corresponding reactors. Aerobic tanks reduced stabilization time and produced negligible odor compared with anaerobic tanks, possibly because of the 2 orders of magnitude lower leachate ammonia levels in the aerobic tank. Both treatment regimes provide the opportunity for disposal and remediation of liquid waste.     

Remedial Strategies for Municipal Solid Waste Management in China

ABSTRACT

The purpose of this investigation is to evaluate the current status and to identify the problems of municipal solid waste (MSW) management in China to determine appropriate remedial strategies. This is the second of two papers proposed on this topic. Major problems or difficulties identified in MSW management in China include MSW land, air, and water pollution, commingled collection, poor administration, shortage of funds, lack of facilities, and problems of training and public awareness.

In order to solve these problems and to improve MSW management in China, remedial strategies in three areas are recommended: institutional reform, technology development, and legislation and administrative improvement. The primary principle involved in institutional reform is unifying legislative responsibilities into one body and developing a market mechanism for handling MSW. Composting, landfills, and incineration should be equally developed in accordance with China's needs. The feasibility of developing technology to handle MSW in China is discussed. Also recommended is the establishment of sound regulatory systems, including a service fee system, a source separation system, and a training program. China is presently undergoing economic and institutional reform at the national and local levels. Results of this study will provide useful information on MSW management in China.     

An Evaluation of Flare Combustion Efficiency Using Open-Path Fourier Transform Infrared Technology

ABSTRACT

Open-path Fourier transform infrared (OP-FTIR) technology was used to evaluate the combustion efficiency of a flare for comparison to several combustion models. Most flares have been considered an effective method for destroying organic compounds and anything that burns. As the Btu content of the flare gas is reduced, the combustion efficiency may also be reduced. Recent studies have suggested that lower Btu flares may have efficiencies as low as 65%. In addition, models have been developed to predict the effect of wind speed and stack discharge velocity on the combustion efficiency. This study was conducted on a low-Btu flare gas that is primarily CO. While the models would predict efficiencies as low as 30%, the sampling using OP-FTIR showed most combustion efficiencies well above 90%. Three methods were used to track combustion efficiency: monitoring the ratio of CO to CO₂, monitoring the ratio of CO to tracer gas, and dispersion modeling. This study was complicated by the presence of two flare stacks, thus two tracer gases were used—SF₆ and CF₄. A method was developed for distinguishing between the two stacks and quantifying the efficiency in each stack.     

Geochemical characterization of acid mine drainage from a waste rock pile, Mine Doyon, Québec, Canada

Water quality in the unsaturated and saturated zones of a waste rock pile containing sulphides was investigated. The main objectives of the project were (1) the evaluation of geochemical trends including the acid mine drainage (AMD)-buffering mechanism and the role of secondary minerals, and (2) the investigation of the use of stable isotopes for the interpretation of physical and geochemical processes in waste rock. Pore water in unsaturated zone was sampled from suction lysimeters and with piezometers in underlying saturated rocks. The investigation revealed strong temporal (dry period vs. recharge period), and spatial (slope vs. central region of pile) variability in the formation of acid mine drainage. The main secondary minerals observed were gypsum and jarosite. There was a higher concentration of gypsum in solid phase at Site TBT than at Site 6, suggesting that part of the gypsum formed at Site 6 in the early stage of AMD has been already dissolved. Formation of secondary minerals contributed to the formation of AMD by opening of foliation planes in waste rock, thus increasing the access of oxidants like O2 and Fe3+ to previously encapsulated pyrite. The behavior of several dissolved species such as Mg, Al, and Fe2+ can be considered as conservative in the leachate. Stable isotopes, deuterium and 18O, indicated internal evaporation within the pile, and were used to trace recharge pulses from snowmelt. Isotope trends for 34S and 18O(SO4) indicated a lack of sulfate reduction and zones of active oxidation of pyrite, respectively. Results of numerical modeling of pyrite oxidation and gas and water transport were consistent with geochemical and isotopic trends and confirmed zones of high evaporation rate within the rock pile close to the slope. The results indicate that physical and chemical processes within the pile are strongly coupled and cannot be considered separately when oxidation rates are high and influence gas transport as a result of heat generation.     

Analysis of long-term settlement of municipal solid waste landfills as determined by various settlement estimation methods

In this study, several existing municipal solid waste (MSW) settlement estimation methods are reviewed and applied to analyze the settlement data of nine MSW landfills. Because a biodegradation-related settlement contributes differently to a long-term total settlement depending on the age of landfills, the actual MSW landfill sites are classified into three groups to specifically address the validity of each method in its prediction of a long-term settlement for each age category. Results demonstrate that there are considerable decreases in predicted settlement potentials as fill age increases. Comparisons indicate that the individual estimation methods display a considerable variation in predicting settlements in the fresh MSW landfills. On the other hand, for the old refuse landfills, all of the estimation methods, except the extended soil model, predict low settlement potentials.