Regional transport and urban contributions to fine particle concentrations in southeastern Canada

The impact of various atmospheric transport directions on ambient fine particle (PM2.5) concentrations at several sites in southeastern Canada was estimated (for May-September) using back-trajectory analysis. Three-day back trajectories (four per day) were paired with 6-hr average PM2.5 mass concentrations measured using tapered element oscillating microbalances (TEOM). PM2.5 concentrations at rural locations in the region were affected by nonlocal sources originating in both Canada and the United States. Comparison of sites revealed that, on average, the local contribution to total PM2.5 in the greater Toronto area (GTA) is approximately 30-35%. At each location, average PM2.5 concentrations under south/southwesterly flow conditions were 2-4 times higher than under the corresponding northerly flow conditions. The chemical composition of both urban and rural PM2.5 was determined during two separate 2-week spring/summer measurement campaigns. Components identified included SO4(2-) NO3-, NH4+, black carbon and organic carbon (OC), and trace elements. Higher particle mass at the urban Toronto site was composed of a higher proportion of all components. However, black carbon, NO3-, NaCl, and trace elements were found to be the most enriched over the rural/regional background levels.     

The Influences of Ambient Particle Composition and Size on Particle Infiltration in Los Angeles,CA, Residences

Abstract

Particle infiltration is a key determinant of the indoor concentrations of ambient particles. Few studies have examined the influence of particle composition on infiltration, particularly in areas with high concentrations of volatile particles, such as ammonium nitrate (NH₄NO₃). A comprehensive indoor monitoring study was conducted in 17 Los Angeles–area homes. As part of this study, indoor/outdoor concentration ratios during overnight (nonindoor source) periods were used to estimate the fraction of ambient particles remaining airborne indoors, or the particle infiltration factor (F_INF), for fine particles (PM_2.5), its nonvolatile (i.e., black carbon [BC]) and volatile (i.e., nitrate [NO₃ ^?]) components, and particle sizes ranging between 0.02 and 10 μm. F_INF was highest for BC (median = 0.84) and lowest for NO₃ ^? (median = 0.18). The low F_INF for NO₃ ^? was likely because of volatilization of NO₃ ^? particles once indoors, in addition to depositional losses upon building entry. The F_INF for PM_2.5 (median = 0.48) fell between those for BC and NO₃ ^?, reflecting the contributions of both particle components to PM_2.5. F_INF varied with particle size, air-exchange rate, and outdoor NO₃ ^? concentrations. The F_INF for particles between 0.7 and 2 μm in size was considerably lower during periods of high as compared with low outdoor NO₃ ^? concentrations, suggesting that outdoor NO₃ ^? particles were of this size. This study demonstrates that infiltration of PM_2.5 varies by particle component and is lowest for volatile species, such as NH₄NO₃. Our results suggest that volatile particle components may influence the ability for outdoor PM concentrations to represent indoor and, thus, personal exposures to particles of ambient origin, because volatilization of these particles causes the composition of PM_2.5 to differ indoors and outdoors. Consequently, particle composition likely influences observed epidemiologic relationships based on outdoor PM concentrations, especially in areas with high concentrations of NH₄NO₃ and other volatile particles.     

Characterization of Major Chemical Components of Fine Particulate Matter in North Carolina

Abstract

This paper presents measurements of daily sampling of fine particulate matter (PM_2.5) and its major chemical components at three urban and one rural locations in North Carolina during 2002. At both urban and rural sites, the major insoluble component of PM_2.5 is organic matter, and the major soluble components are sulfate (SO₄ ^2?), ammonium (NH₄ ⁺), and nitrate (NO₃ ^?). NH₄ ⁺ is neutralized mainly by SO₄ ^2? rather than by NO₃ ^?, except in winter when SO₄ ^2? concentration is relatively low, whereas NO₃ ^? concentration is high. The equivalent ratio of NH₄ ⁺ to the sum of SO₄ ^2? and NO₃ ^? is <1, suggesting that SO₄ ^2?and NO₃ ^?are not completely neutralized by NH₄ ⁺. At both rural and urban sites, SO₄ ^2?concentration displays a maximum in summer and a minimum in winter, whereas NO₃ ^?displays an opposite seasonal trend. Mass ratio of NO₃ ^? to SO₄ ^2?is consistently <1 at all sites, suggesting that stationary source emissions may play an important role in PM_2.5 formation in those areas. Organic carbon and elemental carbon are well correlated at three urban sites although they are poorly correlated at the agriculture site. Other than the daily samples, hourly samples were measured at one urban site. PM_2.5 mass concen trations display a peak in early morning, and a second peak in late afternoon. Back trajectory analysis shows that air masses with lower PM_2.5 mass content mainly originate from the marine environment or from a continental environment but with a strong subsidence from the upper troposphere. Air masses with high PM_2.5 mass concentrations are largely from continental sources. Our study of fine particulate matter and its chemical composition in North Carolina provides crucial information that may be used to determine the efficacy of the new National Ambient Air Quality Standard (NAAQS) for PM fine. Moreover, the gas-to-particle conversion processes provide improved prediction of long-range transport of pollutants and air quality.     

Determination of sources of fine particles in different ambient atmospheres in South Korea using a chemical mass balance model

Abstract

To determine the sources of particulate matter less than 2.5?μm (PM_2.5 in different ambient atmospheres (urban, roadside, industrial, and rural sites), the chemical components of PM_2.5 such as ions (Cl^-, NO₃^-, SO₄^2-, NH₄⁺, Na⁺, K⁺, Ca²⁺, and Mg²⁺), carbonaceous species, and elements (Al, As, Ba, Cd, Cu, Fe, Mn, Ni, Pb, Se, V, and Zn) were measured. The average mass concentrations of PM_2.5 at the urban, roadside, industrial, and rural sites were 31.5?±?14.8, 31.6?±?22.3, 31.4?±?16.0, and 25.8?±?12.4?μg/m³, respectively. Except for secondary ammonium sulfate and ammonium nitrate, the model results showed that the traffic source (i.e., the sum of gasoline and diesel vehicle sources) was the most dominant source of PM_2.5 (17.1%) followed by biomass burning (13.8%) at the urban site. The major primary sources of PM_2.5 were consistent with the site characteristics (diesel vehicle source at the roadside site, coal-fired plants at the industrial site, and biomass burning at the rural site). Seasonal data from the urban site suggested that ammonium sulfate and ammonium nitrate were the most dominant sources of PM_2.5 during all seasons. Further, the contribution of road dust source to PM_2.5 increased during spring and fall seasons. We conclude that the determination of the major PM_2.5 sources is useful for establishing efficient control strategies for PM_2.5 in different regions and seasons.     

A European aerosol phenomenology – 3: Physical and chemical characteristics of particulate matter from 60 rural,urban, and kerbside sites across Europe

This paper synthesizes data on aerosol (particulate matter, PM) physical and chemical characteristics, which were obtained over the past decade in aerosol research and monitoring activities at more than 60 natural background, rural, near-city, urban, and kerbside sites across Europe. The data include simultaneously measured PM₁₀ and/or PM_2.5 mass on the one hand, and aerosol particle number concentrations or PM chemistry on the other hand. The aerosol data presented in our previous works (Van Dingenen et al., 2004, Putaud et al., 2004) were updated and merged to those collected in the framework of the EU supported European Cooperation in the field of Scientific and Technical action COST633 (Particulate matter: Properties related to health effects). A number of conclusions from our previous studies were confirmed. There is no single ratio between PM_2.5 and PM₁₀ mass concentrations valid for all sites, although fairly constant ratios ranging from 0.5 to 0.9 are observed at most individual sites. There is no general correlation between PM mass and particle number concentrations, although particle number concentrations increase with PM_2.5 levels at most sites. The main constituents of both PM₁₀ and PM_2.5 are generally organic matter, sulfate and nitrate. Mineral dust can also be a major constituent of PM₁₀ at kerbside sites and in Southern Europe. There is a clear decreasing gradient in SO₄^2? and NO₃^? contribution to PM₁₀ when moving from rural to urban to kerbside sites. In contrast, the total carbon/PM₁₀ ratio increases from rural to kerbside sites. Some new conclusions were also drawn from this work: the ratio between ultrafine particle and total particle number concentration decreases with PM_2.5 concentration at all sites but one, and significant gradients in PM chemistry are observed when moving from Northwestern, to Southern to Central Europe. Compiling an even larger number of data sets would have further increased the significance of our conclusions, but collecting all the aerosol data sets obtained also through research projects remains a tedious task.     

Characterization of the major chemical species in PM2.5 in the Kaohsiung City,Taiwan

The concentrations and characteristics of the major components in ambient fine particles in the urban city of Kaohsiung, Taiwan were measured and evaluated. PM_2.5 samples were collected using a dichotomous sampler from November 1998 to April 1999 and analyzed for water-soluble ion species using ion chromatography and for carbonaceous species using an elemental analyzer. It was found that SO₄²⁻, NO₃⁻, and NH₄⁺ dominated the identifiable components, and occupied 42.2% and 90.0% of PM_2.5 mass and total dissolved ionic concentrations. Carbonaceous species (organic and elemental carbon) accounted for 20.8% of PM_2.5. The secondary aerosol formed through the NO₂/SO₂ gas-to-particle conversion was estimated based on the sulfur/nitrogen oxidation ratio (SOR/NOR), i.e., sulfate sulfur/nitrate nitrogen to total sulfur/total nitrogen. The average SOR and NOR values were 0.25 and 0.07 for PM_2.5. The high SOR and NOR values obtained in this study suggested that there existed a secondary formation of SO₄²⁻ from SO₂ along with NO₃⁻ from NO₂ in the atmosphere. The secondary organic carbon formed through the volatile organic compound gas-to-particle conversion was estimated from the minimum ratio between organic and elemental carbon obtained in this study, and was found to constitute 40.0% of the total organic carbon for PM_2.5 (6.6% of the particle mass). The results obtained in this study suggest that the formation of secondary aerosols due to conversion from gaseous precursors is significant and important in urban locations.     

Study on ambient concentrations of PM10, PM10–2.5, PM2.5 and gaseous pollutants. Trace elements and chemical speciation of atmospheric particulates

This study provides the first comprehensive report on mass concentrations of particulate matter of various sizes, inorganic and organic gas concentrations monitored at three sampling sites in the city of Palermo (Sicily, Italy). It also provides information on the water-soluble species and trace elements. A total of 2054 PM₁₀ (1333) and PM_2.5 (721) daily measurements were collected from November 2006 to February 2008. The highest mass concentrations were observed at the urban stations, average values being about two times higher than those at the suburban (control) site. Time variations in PM₁₀ and also PM_10–2.5 were observed at the urban stations, the highest concentrations being measured in autumn and winter. CO, NOx, NO₂, benzene, toluene and o-xylene concentrations peaked in autumn and winter, a pattern similar to those recorded for PM₁₀ and PM_10–2.5 mass levels, indicating the importance of traffic emissions in urban air pollution. 91% and 51% of the benzene measurements exceeded the limit of 5 μg m^?3 at the two urban monitoring sites. Trace elements (As, Ba, Cr, Cu, Mo, Pb, Sb) suspected of being introduced into the atmosphere mainly by anthropogenic activities, were highly enriched with respect to local soil. Results indicate that a large fraction of PM₁₀ (31–47% in weight) and PM_2.5 (29% in weight) is made up of water-soluble ions. Ammonium sulphate and nitrate particles accounted for 14–29 wt% of particulate matter mass concentrations. Crustal and marine components, combined, account for 41% and 49% in PM_2.5 and PM₁₀, respectively. The calculated deficits in Cl^- and NH₄⁺ ions suggest that a proportion of these ions are lost, via the formation of gaseous NH₄Cl or HCl and NH₃.     

Observations and Interpretations from the Canadian Fine Particle Monitoring Program

ABSTRACT

Canadian particle monitoring programs examining PM10, PM2.5, and particle composition have been in operation for over 10 years. Until recently, the measurements were manual/filter-based with 24-hr sample collection varying in frequency from daily to every sixth day, using GrasebyAnderson dichotomous samplers. In the past few years, these monitoring activities have been expanded to include hourly measurements using tapered element oscillating microbalances (TEOMs). This continuous monitoring program started operation focusing on PM_10, but now emphasizes PM_2.5 through the addition of more TEOMs and switching of the inlets of some of the existing units. The data from all of these measurement activities show that there are broad geographical differences and also local- to regional-scale spatial differences in mass and composition of PM2.5. Due to variations in sources, significantly different PM2.5 concentrations are not uncommon within the same city. Comparison of nearby urban and rural sites indicates that 30 and 40% of the PM_2.5 is from local urban sources in Montreal and Toronto, respectively. Hourly PM_2.5 measurements in Toronto suggest that vehicular emissions are an important contributor to urban PM_2.5. There has been a decreasing trend in urban PM_2.5, with annual average concentrations between the 1987–1990 and 1993–1995 periods decreasing by 11 to 39%, depending upon the site. The largest declines were in Montreal and Halifax, and the smallest decline was in Toronto. Comparison of 24-hr TEOM and manual dichotomous sampler PM_2.5 measurements from a site in Toronto indicates that the TEOM results in lower concentrations. The magnitude of this difference is relatively small in the warmer months, averaging about 12%. During the colder months the difference averages about 23%, but can be as large as 50%.     

Particulate matter emissions from on-road vehicles in a freeway tunnel study

Particulate matter, including coarse particles (PM_2.5–10, aerodynamic diameter of particle between 2.5 and 10 μm) and fine particles (PM_2.5, aerodynamic diameter of particle lower than 2.5 μm) and their compositions, including elemental carbon, organic carbon, and 11 water-soluble ionic species, and elements, were measured in a tunnel study. A comparison of the six-hour average of light-duty vehicle (LDV) flow of the two sampling periods showed that the peak hours over the weekend were higher than those on weekdays. However, the flow of heavy-duty vehicles (HDVs) on the weekdays was significant higher than that during the weekend in this study. EC and OC content were 49% for PM_2.5–10 and 47% for PM_2.5 in the tunnel center. EC content was higher than OC content in PM_2.5–10, but EC was about 2.3 times OC for PM_2.5. Sulfate, nitrate, ammonium were the main species for PM_2.5–10 and PM_2.5. The element contents of Na, Al, Ca, Fe and K were over 0.8 μg m^?3 in PM_2.5–10 and PM_2.5. In addition, the concentrations of S, Ba, Pb, and Zn were higher than 0.1 μg m^?3 for PM_2.5–10 and PM_2.5. The emission factors of PM_2.5–10 and PM_2.5 were 18 ± 6.5 and 39 ± 11 mg km^?1-vehicle, respectively. The emission factors of EC/OC were 3.6/2.7 mg km^?1-vehicle for PM_2.5–10 and 15/4.7 mg km^?1-vehicle for PM_2.5 Furthermore, the emission factors of water-soluble ions were 0.028(Mg²⁺)–0.81(SO₄^2?) and 0.027(NO₂^?)–0.97(SO₄^2?) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively. Elemental emission factors were 0.003(V)–1.6(Fe) and 0.001(Cd)–1.05(Na) mg km^?1-vehicle for PM_2.5–10 and PM_2.5, respectively.     

Modeling an air pollution episode in northwestern United States: Identifying the effect of nitrogen oxide and volatile organic compound emission changes on air pollutants formation using direct sensitivity analysis

Air quality impacts of volatile organic compound (VOC) and nitrogen oxide (NO_x) emissions from major sources over the northwestern United States are simulated. The comprehensive nested modeling system comprises three models: Community Multiscale Air Quality (CMAQ), Weather Research and Forecasting (WRF), and Sparse Matrix Operator Kernel Emissions (SMOKE). In addition, the decoupled direct method in three dimensions (DDM-3D) is used to determine the sensitivities of pollutant concentrations to changes in precursor emissions during a severe smog episode in July of 2006. The average simulated 8-hr daily maximum O₃ concentration is 48.9 ppb, with 1-hr O₃ maxima up to 106 ppb (40 km southeast of Seattle). The average simulated PM_2.5 (particulate matter with an aerodynamic diameter <2.5 μm) concentration at the measurement sites is 9.06 μg m^?3, which is in good agreement with the observed concentration (8.06 μg m^?3). In urban areas (i.e., Seattle, Vancouver, etc.), the model predicts that, on average, a reduction of NO_x emissions is simulated to lead to an increase in average 8-hr daily maximum O₃ concentrations, and will be most prominent in Seattle (where the greatest sensitivity is??0.2 ppb per % change of mobile sources). On the other hand, decreasing NO_x emissions is simulated to decrease the 8-hr maximum O₃ concentrations in remote and forested areas. Decreased NO_x emissions are simulated to slightly increase PM_2.5 in major urban areas. In urban areas, a decrease in VOC emissions will result in a decrease of 8-hr maximum O₃ concentrations. The impact of decreased VOC emissions from biogenic, mobile, nonroad, and area sources on average 8-hr daily maximum O₃ concentrations is up to 0.05 ppb decrease per % of emission change, each. Decreased emissions of VOCs decrease average PM_2.5 concentrations in the entire modeling domain. In major cities, PM_2.5 concentrations are more sensitive to emissions of VOCs from biogenic sources than other sources of VOCs. These results can be used to interpret the effectiveness of VOC or NO_x controls over pollutant concentrations, especially for localities that may exceed National Ambient Air Quality Standards (NAAQS).

Implications: The effect of NO_x and VOC controls on ozone and PM_2.5 concentrations in the northwestern United States is examined using the decoupled direct method in three dimensions (DDM-3D) in a state-of-the-art three-dimensional chemical transport model (CMAQ). NO_x controls are predicted to increase PM_2.5 and ozone in major urban areas and decrease ozone in more remote and forested areas. VOC reductions are helpful in reducing ozone and PM_2.5 concentrations in urban areas. Biogenic VOC sources have the largest impact on O₃ and PM_2.5 concentrations.     

Particulate Matter in California: Part 2—Spatial,Temporal, and Compositional Patterns of PM2.5, PM10–2.5, and PM10

Abstract

Geographic and temporal variations in the concentration and composition of particulate matter (PM) provide important insights into particle sources, atmospheric processes that influence particle formation, and PM management strategies. In the nonurban areas of California, annual-average PM_2.5 and PM₁₀ concentrations range from 3 to 10 [H9262]g/m³ and from 5 to 18 µg/m³, respectively. In the urban areas of California, annual-averages for PM_2.5 range from 7 to 30 [H9262]g/m³, with observed 24-hr peaks reaching levels as high as 160 [H9262]g/m³. Within each air basin, exceedances are a mixture of isolated events as well as periods of elevated PM_2.5 concentrations that are more prolonged and regional in nature. PM_2.5 concentrations are generally highest during the winter months. The exception is the South Coast Air Basin, where fairly high values occur throughout the year. Annual-average PM_2.5 mass, as well as the concentrations of major components, declined from 1988 to 2000. The declines are especially pronounced for the sulfate (SO₄ ^2?) and nitrate (NO₃ ^?) components of PM_2.5 and PM₁₀ and correlate with reductions in ambient levels of oxides of sulfur (SO_x) and oxides of nitrogen (NO_x). Annual averages for PM_10–2.5 and PM₁₀ exhibited similar downwind trends from 1994 to 1999, with a slightly less pronounced decrease in the coarse fraction.     

Fine particulate speciation profile and emission factor of municipal solid waste incinerator established by dilution sampling method

In this study, fine particulate matter (PM_2.5) emitted from a municipal solid waste incinerator (MSWI) was collected using dilution sampling method. Chemical compositions of the collected PM_2.5 samples, including carbon content, metal elements, and water-soluble ions, were analyzed. Traditional in-stack hot sampling was simultaneously conducted to compare the influences of dilution on PM_2.5 emissions and the characteristics of the bonded chemical species. The results, established by a dilution sampling method, show that PM_2.5 and total particulate matter (TPM) emission factors were 61.6 ± 4.52 and 66.1 ± 5.27 g ton-waste^?1, respectively. The average ratio of PM_2.5/TPM is 0.93, indicating that more than 90% of PM emission from the MSWI was fine particulate. The major chemical species in PM_2.5 included organic carbon (OC), Cl^?, NH₄⁺, elemental carbon (EC) and Si, which account for 69.7% of PM_2.5 mass. OC was from the unburned carbon in the exhaust, which adsorbed onto the particulate during the cooling process. High Cl^? emission is primarily attributable to wastes containing plastic bags made of polyvinyl chloride, salt in kitchen refuse and waste biomass, and so on. Minor species that account for 0.01–1% of PM_2.5 mass included SO₄^2-, K⁺, Na, K, NO₃^?, Al, Ca²⁺, Zn, Ca, Cu, Fe, Pb, and Mg. The mean ratio of dilution method/in-stack hot method was 0.454. The contents of water-soluble ions (Cl^?, SO₄^2-, NO₃^?) were significantly enriched in PM_2.5 via gas-to-particle conversion in the dilution process. Results indicate that in-stack hot sampling would underestimate levels of these species in PM_2.5.

Implications: PM_2.5 samples from a municipal solid waste incinerator (MSWI) were collected simultaneously by a dilution sampling technique and a traditional in-stack method. PM_2.5 emission factors and chemical speciation profiles were established. Dilution sampling provides more reliable data than in-stack hot sampling. The results can be applied to estimate the PM_2.5 emission inventories of MSWI, and the source profile can be used for contribution estimate of chemical mass balance modeling.     

Application and Evaluation of Two Air Quality Models for Particulate Matter for a Southeastern U.S. Episode

Abstract

The Models-3 Community Multiscale Air Quality (CMAQ) Modeling System and the Particulate Matter Comprehensive Air Quality Model with extensions (PMCAMx) were applied to simulate the period June 29–July 10, 1999, of the Southern Oxidants Study episode with two nested horizontal grid sizes: a coarse resolution of 32 km and a fine resolution of 8 km. The predicted spatial variations of ozone (O₃), particulate matter with an aerodynamic diameter less than or equal to 2.5 μm (PM_2.5), and particulate matter with an aerodynamic diameter less than or equal to 10 μm (PM₁₀) by both models are similar in rural areas but differ from one another significantly over some urban/suburban areas in the eastern and southern United States, where PMCAMx tends to predict higher values of O₃ and PM than CMAQ. Both models tend to predict O₃ values that are higher than those observed. For observed O₃ values above 60 ppb, O₃ performance meets the U.S. Environmental Protection Agency's criteria for CMAQ with both grids and for PMCAMx with the fine grid only. It becomes unsatisfactory for PMCAMx and marginally satisfactory for CMAQ for observed O₃ values above 40 ppb.

Both models predict similar amounts of sulfate (SO₄ ^2?) and organic matter, and both predict SO₄ ^2? to be the largest contributor to PM_2.5. PMCAMx generally predicts higher amounts of ammonium (NH₄ ⁺), nitrate (NO₃ ^?), and black carbon (BC) than does CMAQ. PM performance for CMAQ is generally consistent with that of other PM models, whereas PMCAMx predicts higher concentrations of NO₃ ^?,NH₄ ⁺, and BC than observed, which degrades its performance. For PM₁₀ and PM_2.5 predictions over the southeastern U.S. domain, the ranges of mean normalized gross errors (MNGEs) and mean normalized bias are 37–43% and –33–4% for CMAQ and 50–59% and 7–30% for PMCAMx. Both models predict the largest MNGEs for NO₃ ^? (98–104% for CMAQ, 138–338% for PMCAMx). The inaccurate NO₃ ^? predictions by both models may be caused by the inaccuracies in the ammonia emission inventory and the uncertainties in the gas/particle partitioning under some conditions. In addition to these uncertainties, the significant PM overpredictions by PMCAMx may be attributed to the lack of wet removal for PM and a likely underprediction in the vertical mixing during the daytime.     

Air Quality Measurements from the Fresno Supersite

ABSTRACT

The Fresno Supersite intends to 1) evaluate non-routine monitoring methods, establishing their comparability with existing methods and their applicability to air quality planning, exposure assessment, and health effects studies; 2) provide a better understanding of aerosol characteristics, behavior, and sources to assist regulatory agencies in developing standards and strategies that protect public health; and 3) support studies that evaluate relationships between aerosol properties, co-factors, and observed health end-points. Supersite observables include in-situ, continuous, short-duration measurements of 1) PM_2.5, PM₁₀, and coarse (PM₁₀ minus PM_2.5) mass; 2) PM_2.5 SO₄ ^-2, NO₃ ^-, carbon, light absorption, and light extinction; 3) numbers of particles in discrete size bins ranging from 0.01 to ~10μm; 4) criteria pollutant gases (O₃, CO, NO_x); 5) reactive gases (NO₂, NO_y, HNO₃, peroxyacetyl nitrate [PAN], NH₃); and 6) single particle characterization by time-of-flight mass spectrometry. Field sampling and laboratory analysis are applied for gaseous and particulate organic compounds (light hydrocarbons, heavy hydrocarbons, carbonyls, polycyclic aromatic hydrocarbons [PAH], and other semi-volatiles), and PM_2.5 mass, elements, ions, and carbon. Observables common to other Supersites are 1) daily PM_2.5 24-hr average mass with Federal Reference Method (FRM) samplers; 2) continuous hourly and 5-min average PM_2.5 and PM₁₀ mass with beta attenuation monitors (BAM) and tapered element oscillating microbalances (TEOM); 3) PM_2.5 chemical specia-tion with a U.S. Environmental Protection Agency (EPA) speciation monitor and protocol; 4) coarse particle mass by dichotomous sampler and difference between PM₁₀ and PM_2.5 BAM and TEOM measurements; 5) coarse particle chemical composition; and 6) high sensitivity and time resolution scalar and vector wind speed, wind direction, temperature, relative humidity, barometric pressure, and solar radiation. The Fresno Supersite is coordinated with health and toxicological studies that will use these data in establishing relationships with asthma, other respiratory disease, and cardiovascular changes in human and animal subjects.     

Rapid Nitrate Loss from PM10 Filters

The Monterrey Metropolitan Area (MMA) has shown a high concentration of PM_2.5 in its atmosphere since 2003. The contribution of possible sources of primary PM_2.5 and its precursors is not known. In this paper we present the results of analyzing the chemical composition of sixty 24-hr samples of PM_2.5 to determine possible sources of PM_2.5 in the MMA. The samples were collected at the northeast and southeast of the MMA between November 22 and December 12, 2007, using low-volume devices. Teflon and quartz filters were used to collect the samples. The concentrations of 16 airborne trace elements were determined using x-ray fluorescence (XRF). Anions and cations were determined using ion chromatography. Organic carbon (OC) and elemental carbon (EC) were determined by thermal optical analysis. The results show that Ca had the maximum mean concentration of all elements studied, followed by S. Enrichment factors above 50 were calculated for S, Cl, Cu, Zn, Br, and Pb. This indicates that these elements may come from anthropogenic sources. Overall, the major average components of PM_2.5 were OC (41.7%), SO₄ ^2? (22.9%), EC (7.4%), crustal material (11.4%), and NO₃ ^? (12.6%), which altogether accounted for 96% of the mass. Statistically, we did not find any difference in SO₄ ^2? concentrations between the two sites. The fraction of secondary organic carbon was between 24% and 34%. The results of the factor analysis performed over 10 metals and OC and EC show that there are three main sources of PM_2.5: crustal material and vehicle exhaust; industrial activity; and fuel oil burning. The results show that SO₄ ^2?, OC, and crustal material are important components of PM_2.5 in MMA. Further work is necessary to evaluate the proportion of secondary inorganic and organic aerosol in order to have a better understanding of the sources and precursors of aerosols in the MMA.

Implications: The MMA has become one of the most air polluted areas in Mexico. High levels of PM_2.5 have been measured and effective actions need to be taken to reduce air pollution and the associated health risks. Several sources of primary PM_2.5 and precursors of secondary particles exist in the MMA. This study provides valuable information for the local environmental authorities to identify possible sources of primary PM_2.5 and its precursors. The effectiveness of the actions taken to improve air quality will lead to health benefits for the population, reducing their associated costs.     

Chemical characterization of particles in winter-night smog in Tokyo

Continuous measurement of PM₁₀, PM_2.5 and carbon (organic, elemental composition) concentrations, and samples of PM₁₀ and PM_2.5 collected on a polycarbonate membrane filter (Nuclepore^®, pore size: 0.8 μm), were carried out during a period from December 1998 to January 1999 at Shinjuku in Tokyo in order to investigate the chemical characterization of particles in winter-night smog within a large area of the Japan Kanto Plain including the Tokyo Metropolitan area. These were measured using an ambient particulate monitor (tapered element oscillating microbalance—TEOM) and a carbon particulate monitor. Elemental compositions in the filter samples of PM₁₀ and PM_2.5 were determined by means of particle-induced X-ray emission (PIXE) analysis. Ionic species (anion: F⁻, Cl⁻, NO₃⁻, SO₄²⁻ and C₂O₄²⁻; cation: Na⁺, NH₄⁺, K⁺, Ca²⁺ and Mg²⁺) in the filter samples were analyzed by ion chromatography. The temporal variation patterns of PM_2.5 were similar to those of PM₁₀ and carbon. PM_2.5 made up 90% of the PM₁₀ at a high concentration, and 70% at a low concentration. Concentrations of 22 elements in both the PM₁₀ and PM_2.5 samples were consistently determined by PIXE, and Na, Mg, Al, Si, S, Cl, K, Ca, Fe, Zn and Pb were found to be the major components. Among these S and Cl were the most dominant elements of the PM_2.5 and PM₁₀ at high concentrations. Ionic species were mainly composed of Cl⁻, NO₃⁻, SO₄²⁻ and NH₄⁺. The component proportion of carbon, the other elements (total amount of measured elements other than S and Cl) and secondary-formed particles of PM_2.5 was similar to that of PM₁₀. The major component was carbon particles at a low concentration and secondary-formed particles at a high concentration. The proportion of NH₄NO₃ and NH₄Cl plus HCl in secondary-formed particles at a high concentration, in particular, was as high as 90%.     

Reduction of atmospheric fine particle level by restricting the idling vehicles around a sensitive area

Atmospheric particles are a major problem that could lead to harmful effects on human health, especially in densely populated urban areas. Chiayi is a typical city with very high population and traffic density, as well as being located at the downwind side of several pollution sources. Multiple contributors for PM_2.5 (particulate matter with an aerodynamic diameter ≥2.5 μm) and ultrafine particles cause complicated air quality problems. This study focused on the inhibition of local emission sources by restricting the idling vehicles around a school area and evaluating the changes in surrounding atmospheric PM conditions. Two stationary sites were monitored, including a background site on the upwind side of the school and a campus site inside the school, to monitor the exposure level, before and after the idling prohibition. In the base condition, the PM_2.5 mass concentrations were found to increase 15% from the background, whereas the nitrate (NO₃^?) content had a significant increase at the campus site. The anthropogenic metal contents in PM_2.5 were higher at the campus site than the background site. Mobile emissions were found to be the most likely contributor to the school hot spot area by chemical mass balance modeling (CMB8.2). On the other hand, the PM_2.5 in the school campus fell to only 2% after idling vehicle control, when the mobile source contribution reduced from 42.8% to 36.7%. The mobile monitoring also showed significant reductions in atmospheric PM_2.5, PM_0.1, polycyclic aromatic hydrocarbons (PAHs), and black carbon (BC) levels by 16.5%, 33.3%, 48.0%, and 11.5%, respectively. Consequently, the restriction of local idling emission was proven to significantly reduce PM and harmful pollutants in the hot spots around the school environment.

Implications: The emission of idling vehicles strongly affects the levels of particles and relative pollutants in near-ground air around a school area. The PM_2.5 mass concentration at a campus site increased from the background site by 15%, whereas NO₃^? and anthropogenic metals also significantly increased. Meanwhile, the PM_2.5 contribution from mobile source in the campus increased 6.6% from the upwind site. An idling prohibition took place and showed impressive results. Reductions of PM_2.5, ionic component, and non-natural metal contents were found after the idling prohibition. The mobile monitoring also pointed out a significant improvement with the spatial analysis of PM_2.5, PM_0.1, PAH, and black carbon concentrations. These findings are very useful to effectively improve the local air quality of a densely city during the rush hour.     

Temporal and spatial relationships in fine particle strong acidity, sulphate, PM1O, and PM2.5 across multiple canadian locations

The Canadian Acid Aerosol Measurement Program (CAAMP) was established in 1992 to gain a better understanding of the atmospheric behaviour of fine particle strong acidity (“acid aerosols”) and to facilitate an assessment of the potential health risks associated with acid aerosols and particles in general. During 1992. 1993 and 1994, annular denuder and filter measurements were taken at four sites in Ontario, two in Quebec, three in the Atlantic Provinces and one in the greater Vancouver area. Mean fine particle sulphate concentrations (SO₄²⁻) were highest in southern Ontario (annual average ranged from 40–70 nmol m⁻³), lowest at a site in the Vancouver area (average = 16 nmol m⁻³) and second lowest in rural Nova Scotia. However, mean fine particle strong acid concentrations (H⁺) were geographically different. The highest mean concentrations were at the east coast sites (annual average of up to 30 nmol m⁻³). Acidities were lower in areas where the fine particle acidity experienced greater neutralization from reaction with ammonia. This included the major urban centres (i.e. Toronto and Montréal) and areas with greater amounts of agricultural activity, as in rural southern Ontario. On average, ambient concentrations of fine and coarse particle mass were larger in the urban areas and also in areas where SO₄²⁻ levels were higher. All the particle components were episodic. However, compared to SO₄²⁻ and fine particles (PM_2.5 or PM_2.1, depending upon inlet design), episodes of H⁺ tended to be less frequent and of shorter duration, particularly in Ontario. Saint John, New Brunswick, had the highest mean annual H⁺ concentration, which was 30 nmol m⁻³. H⁺ episodes (24 h concentration > 100 nmol m⁻³) were also the most frequent at this location. The high levels in Saint John were partially due to local sulphur dioxide sources and heterogeneous chemistry occurring in fog, which, on average, led to a 50% enhancement in sulphate, relative to upwind conditions.There was a substantial amount of intersite correlation in the day to day variations in H⁺, SO₄²⁻ , PM_2.5 and PM₁₀ (fine + coarse particles) concentrations, which is due to the influence of synoptic-scale meteorology and the relatively long atmospheric lifetime of fine particles. Sulphate was the most regionally homogenous species. Pearson correlation coefficients comparing SO₄²⁻ between sites ranged from 0.6 to 0.9, depending on site separation and lag time. In many cases, particle episodes were observed to move across the entire eastern portion of Canada with about a two-day lag between the SO₄²⁻ levels in southern Ontario and in southern Nova Scotia.     

Spatial differences in ambient coarse and fine particles in the Monterrey metropolitan area,Mexico: Implications for source contribution

The ambient air of the Monterrey Metropolitan Area (MMA) in Mexico frequently exhibits high levels of PM₁₀ and PM_2.5. However, no information exists on the chemical composition of coarse particles (PM_c = PM₁₀ – PM_2.5). A monitoring campaign was conducted during the summer of 2015, during which 24-hr average PM₁₀ and PM_2.5 samples were collected using high-volume filter-based instruments to chemically characterize the fine and coarse fractions of the PM. The collected samples were analyzed for anions (Cl^–, NO₃^–, SO₄^2–), cations (Na⁺, NH₄⁺, K⁺), organic carbon (OC), elemental carbon (EC), and 35 trace elements (Al to Pb). During the campaign, the average PM_2.5 concentrations did not showed significance differences among sampling sites, whereas the average PM_c concentrations did. In addition, the PM_c accounted for 75% to 90% of the PM₁₀ across the MMA. The average contribution of the main chemical species to the total mass indicated that geological material including Ca, Fe, Si, and Al (45%) and sulfates (11%) were the principal components of PM_c, whereas sulfates (54%) and organic matter (30%) were the principal components of PM_2.5. The OC-to-EC ratio for PM_c ranged from 4.4 to 13, whereas that for PM_2.5 ranged from 3.97 to 6.08. The estimated contribution of Secondary Organic Aerosol (SOA) to the total mass of organic aerosol in PM_2.5 was estimated to be around 70–80%; for PM_c, the contribution was lower (20–50%). The enrichment factors (EF) for most of the trace elements exhibited high values for PM_2.5 (EF: 10–1000) and low values for PM_c (EF: 1–10). Given the high contribution of crustal elements and the high values of EFs, PM_c is heavily influenced by soil resuspension and PM_2.5 by anthropogenic sources. Finally, the airborne particles found in the eastern region of the MMA were chemically distinguishable from those in its western region.

Implications: Concentration and chemical composition patterns of fine and coarse particles can vary significantly across the MMA. Public policy solutions have to be built based on these observations. There is clear evidence that the spatial variations in the MMA’s coarse fractions are influenced by clearly recognizable primary emission sources, while fine particles exhibit a homogeneous concentration field and a clear spatial pattern of increasing secondary contributions. Important reductions in the coarse fraction can come from primary particles’ emission controls; for fine particles, control of gaseous precursors—particularly sulfur-containing species and organic compounds—should be considered.     

Characterization of PM2.5-bound polycyclic aromatic hydrocarbons in Atlanta—Seasonal variations at urban,suburban, and rural ambient air monitoring sites

Twenty-eight polycyclic aromatic hydrocarbons (PAH) and methylated PAHs (Me-PAH) were measured in daily PM_2.5 samples collected at an urban site, a suburban site, and a rural site in and near Atlanta during 2004 (5 samples/month/site). The suburban site, located near a major highway, had higher PM_2.5-bound PAH concentrations than did the urban site, and the rural site had the lowest PAH levels. Monthly variations are described for concentrations of total PAHs (∑PAHs) and individual PAHs. PAH concentrations were much higher in cold months than in warm months, with average monthly ∑PAH concentrations at the urban and suburban-highway monitoring sites ranging from 2.12 to 6.85 ng m^?3 during January–February and November–December 2004, compared to 0.38–0.98 ng m^?3 during May–September 2004. ∑PAH concentrations were found to be well correlated with PM_2.5 and organic carbon (OC) within seasons, and the fractions of PAHs in PM_2.5 and OC were higher in winter than in summer. Methyl phenanthrenes were present at higher levels than their un-substituted homologue (phenanthrene), suggesting a petrogenic (unburned petroleum products) input. Retene, a proposed tracer for biomass burning, peaked in March, the month with the highest acreage and frequency of prescribed burning and unplanned fires, and in December, during the high residential wood-burning season, indicating that retene might be a good marker for burning of all biomass materials. In contrast, potassium peaked only in December, indicating that it might be a more specific tracer for wood-burning.