Decomposition of gas phase 1,3-butadiene by ultraviolet/ozone process

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne 1,3-butadiene (BD) via ozonation (O3) and ultraviolet (UV)/O3 technologies. Governing factors, such as the initial molar ratio of ozone to BD, UV volumetric electric input power, and moisture content in the influent airstream, were investigated. Experiments were conducted at an influent BD concentration of approximately 50 ppm, an ambient temperature of 26 degrees C, and a gas retention time of 85 sec. Results show that an initial molar ratio of ozone to BD of 3.5 and 2 sufficed to obtain BD decompositions of >90% for ozonation and UV/O3, respectively. The UV irradiance did not directly promote the decomposition of BD, rather, it played a role in promoting the production of secondary oxidants, such as hydroxyl radicals. Kinetic analyses indicate that both types of BD decomposition are peudo-first-order with respect to BD concentrations. Moisture content (relative humidity = 40-99%) and UV volumetric electric input power (0.147 and 0.294 W/L) are both factors that weakly affect the rate of BD decomposition. Economic evaluation factors, including both energy of ozone production and UV electric input power, were also estimated.     

Degradation of gas-phase propylene glycol monomethyl ether acetate by ultraviolet/ozone process: A kinetic study

A pilot-scale plug-flow reactor was built to investigate its performance in treating airborne propylene glycol monomethyl ether acetate (PGMEA) via ozonation, ultraviolet (UV) photolysis and UV/O3 technologies. Governing factors, such as the initial molar ratio of ozone (O3) to PG-MEA, UV volumetric electric power input, and moisture content in the influent airstream, were investigated. A 1-L batch reactor was used to investigate some photodegradation characteristics of PGMEA in advance. Experiments were conducted at a fixed influent PGMEA concentration of approximately 50 ppm and an ambient temperature of 26 degrees C. A gas space time of 85 sec in the plug-flow reactor was kept for either ozonation or photolysis reaction, whereas a gas space time of 170 sec was used for the UV/O3 degradation. Results show that an initial molar ratio of O3 to PGMEA of >2.91 and an UV volumetric electric input power of 0.294 W/L(-1) sufficed to obtain PGMEA decompositions of >90% by UV/O3. Kinetic analyses indicate that all types of PGMEA decomposition are pseudo-first order with respect to its concentration. Moisture content (relative humidity = 15-99%) and UV volumetric electric input power (0.147 and 0.294 W/L(-1)) were major factors that strongly affect the PGMEA degradation rate.     

SMX degradation by ozonation and UV radiation: a kinetic study

The rate constants of sulfamethoxazole (SMX) degradation by ozonation and UV₂₅₄ radiation were investigated under various parameters including influent ozone gas concentration, initial SMX concentration, UV light intensity, ionic strength, water quality in terms of varying anions (bicarbonate, sulfate and nitrate), humic acid (HA) and pH. The results indicated that the removal of SMX by ozonation and UV₂₅₄ radiation fitted well to a pseudo first-order kinetic model and the rate constants were in the range of (0.9-9.8) × 10⁻³ and (1.7-18.9) × 10⁻³ s⁻¹, respectively. The second-order rate constants of SMX with ozone (k_O3), under varying operational parameters, were also determined and varied in the range of (0.60-3.38) ± 0.13 × 10⁵ M⁻¹ s⁻¹. In addition, SMX degradation through UV pretreatment followed by ozonation in the presence of HA was proved to be an effective method which can remove SMX with a low ozone dose. The results suggested that ozonation of SMX was more affected by concentration of influent ozone gas, alkalinity, and HA, while incident UV light intensity, pH, and HA were the dominant factors influencing UV degradation of SMX.     

Photocatalytic ozonation of terephthalic acid: a by-product-oriented decomposition study

Terephthalic acid (TA) is considered as a refractory model compound. For this reason, the TA degradation usually requires a prolonged reaction time to achieve mineralization. In this study, vanadium oxide (V_xO_y) supported on titanium oxide (TiO₂) served as a photocatalyst in the ozonation of the TA with light-emitting diodes (LEDs), having a bandwidth centered at 452 nm. The modified catalyst (V_xO_y/TiO₂) in combination with ozone and LEDs improved the TA degradation and its by-products. The results obtained by this system were compared with photolysis, single ozonation, catalytic ozonation, and photocatalytic ozonation of V_xO_y/TiO₂ with UV lamp. The LED-based photocatalytic ozonation showed almost the same decomposition efficiency of the TA, but it was better in comparison with the use of UV lamp. The oxalic acid accumulation, as the final product of the TA decomposition, was directly influenced by either the presence of V_xO_y or/and the LED irradiation. Several by-products formed during the TA degradation, such as muconic, fumaric, and oxalic acids, were identified. Besides, two unidentified by-products were completely removed during the observed time (60 min). It was proposed that the TA elimination in the presence of V_xO_y/TiO₂ as catalyst was carried out by the combination of different mechanisms: molecular ozone reaction, indirect mechanism conducted by ·OH, and the surface complex formation.     

Atrazine removal by ozonation processes in surface waters

Abstract

Atrazine (6‐chloro‐N‐ethyl‐N'‐isopropyl‐1,3,5‐triazinedyl‐2,4‐diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O₃/H₂O₂ process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O₃/H₂O₂ and O₃/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Comparison of various advanced oxidation processes for the degradation of phenylurea herbicides

Various types of advanced oxidation processes (AOPs), such as UV photolysis, ozonation, heterogeneous photocatalysis and their combinations were comparatively examined at the same energy input in a home-made reactor. The oxidative transformations of the phenylurea herbicides fenuron, monuron and diuron were investigated. The initial rates of transformation demonstrated that UV photolysis was highly efficient in the cases of diuron and monuron. Ozonation proved to be much more effective in the transformation of fenuron than in those of the chlorine containing monuron and diuron. In heterogeneous photocatalysis, the rate of decomposition decreased with increase of the number of chlorine atoms in the target molecule. Addition of ozone to UV-irradiated solutions and/or TiO₂-containing suspensions markedly increased the initial rates of degradation. Dehalogenation of monuron and diuron showed that each of these procedures is suitable for the simultaneous removal of chlorinated pesticides and their chlorinated intermediates. Heterogeneous photocatalysis was found to be effective in the mineralization.     

Ozonation as an advanced oxidant in treatment of bamboo industry wastewater

The present study employed ozonation process to treat the bamboo industry wastewater (BIWW). The impact of ozone dosage and initial organic concentration on color, COD and TOC removal rates were studied along with characterization of the major organics in raw and treated wastewater. The results suggested the ozone dosage of 3.15 g h⁻¹ (concentration 52.5 mg L⁻¹) was suitable for the treatment. After 25 min ozonation of 1 L raw wastewater, the color, COD and TOC removal efficiencies were 95%, 56% and 40%, respectively, with an influent COD concentration of 835 mg L⁻¹. The ratio of kg O₃ kg⁻¹ COD at 3.15 g h⁻¹ was 2.8 (<3), revealing that ozonation was a cost effective process for tertiary treatment of BIWW. Longer oxidization time was required to achieve similar results for raw wastewater with higher COD concentration. The chromatogram from gel permeation chromatography revealed that ozonation resulted in the breakdown of high molecular weight compounds into lower molecular weight components but could not completely mineralize the organic matter. The majority of these compounds were identified in both raw and ozonated samples via GC-MS analysis. In addition to ester derivatives as the main intermediates of ozonation, 1-chloroctadecane, methyl stearate, benzophenone and α-cyperone were identified as the by-products of ozonation.     

Degradation of atrazine by catalytic ozonation in the presence of iron scraps: performance,transformation pathway,and acute toxicity

Degradation of atrazine by catalytic ozonation in the presence of iron scraps (ZVI/O₃) was carried out. The key operational parameters (i.e., initial pH, ZVI dosage, and ozone dosage) were optimized by the batch experiments, respectively. This ZVI/O₃ system exhibited much higher degradation efficiency of atrazine than the single ozonation, ZVI, and traditional ZVI/O₂ systems. The result shows that the pseudo-first-order constant (0.0927?min^?1) and TOC removal rate (86.6%) obtained by the ZVI/O₃ process were much higher than those of the three control experiments. In addition, X-ray diffraction (XRD) analysis indicates that slight of γ-FeOOH and Fe₂O₃ were formed on the surface of iron scrap after ZVI/O₃ treatment. These corrosion products exhibit high catalytic ability for ozone decomposition, which could generate more hydroxyl radical (HO^?) to degrade atrazine. Six transformation intermediates were identified by liquid chromatography-mass spectrometry (LC-MS) analysis in ZVI/O₃ system, and the degradation pathway of atrazine was proposed. Toxicity tests based on the inhibition of the luminescence emitted by Photobacterium phosphoreum and Vibrio fischeri indicate the detoxification of atrazine by ZVI/O₃ system. Finally, reused experiments indicate the approving recyclability of iron scraps. Consequently, the ZVI/O₃ system could be as an effective and promising technology for pesticide wastewater treatment.     

污泥基活性炭催化臭氧氧化对氯苯甲酸效能

以城市污水处理厂剩余污泥和玉米芯为原料,用氯化锌活化法制备出污泥基活性炭(SCAC),研究了其催化臭氧氧化去除水中对氯苯甲酸(p-CBA)的效能和机理,同时,考察了臭氧浓度、SCAC投量、p-CBA初始浓度以及自由基抑制剂叔丁醇的加入对SCAC催化活性的影响。实验结果表明,SCAC的加入可以显著提高臭氧对p-CBA的氧化去除效果,在反应初期尤为明显,反应1.0 min时p-CBA的去除率由单独臭氧氧化的26.1%提高到SCAC催化臭氧氧化的60.2%。SCAC催化臭氧氧化对p-CBA的去除率随臭氧浓度的增加和p-CBA初始浓度的减小而增加。此外,在一定范围内增加催化剂的投量可以增加p-CBA的去除率。叔丁醇的加入显著减弱了SCAC催化臭氧氧化降解p-CBA的效能,表明SCAC催化臭氧氧化反应的主要活性物种为羟基自由基(·OH)。     

A new approach to quantify the degradation kinetics of linuron with UV, ozonation and UV/O3 processes

The degradation of linuron, one of phenylurea herbicides, was investigated for its reaction kinetics by different treatment processes including ultraviolet irradiation (UV), ozonation (O₃), and UV/O₃. The decay rate of linuron by UV/O₃ process was found to be around 3.5 times and 2.5 times faster than sole-UV and ozone-alone, respectively. Experimental results also indicate overall rate constants increased exponentially with pH above 9.0 while the increase of rate constants with pH below 9 is insignificant in O₃ system. All dominant parameters involved in the three processes were determined in the assistant of proposed linear models in this study. The approach was found useful in predicting the process performances through the quantification of quantum yield (rate constant for the formation of free radical HOO⁻ from ozone decomposition at high pH), rate constant of linuron with ozone (k_O3,LNR), rate constant of linuron with hydroxyl radical (k_OH,LNR), and α (the ratio of the production rate of OH and the decay rate of ozone in UV/O₃ system).     

Heterogeneous Oxidation by Ozone of Naphthalene Adsorbed at the Air-Water Interface of Micron-Size Water Droplets

Abstract

The mass transfer of naphthalene vapor to water droplets in air was studied in the presence of ozone (O₃) in the gas phase. A falling droplet reactor with water droplets of diameters 55, 91, and 182 μm was used for the study. O₃ reacted with naphthalene at the air-water interface, thereby decreasing the mass transfer resistance and increasing the rate of uptake of naphthalene into the droplet. A Langmuir-Hinshelwood reaction mechanism at the air-water interface satisfactorily described the surface reaction. The first-order surface reaction rate constant, k_s, increased with decreasing droplet size. Three organic intermediates were identified in the aqueous phase as a result of ozonation of naphthalene at the surface of the droplet indicating both peroxidic and nonperoxidic routes for ozonation. The presence of an organic carbon surrogate (fulvic acid) increased both the partition constant of naphthalene and the surface reaction rate of O₃. The heterogeneous oxidation of naphthalene by O₃ on the droplet was 15 times faster than the homogeneous oxidation by O₃ in the bulk air phase, whereas it was only 0.08 times the homogeneous gas-phase oxidation by hydroxyl radicals under atmospheric conditions.     

臭氧/紫外联合降解甲醛的试验研究

在臭氧单独作用、紫外光单独作用和UV/O₃ 3种条件下分别对甲醛进行降解试验，研究表明,臭氧和紫外在降解甲醛的试验中存在明显的协同促进作用。单独臭氧对甲醛降解效果并不显著。紫外单独作用时，对甲醛几乎没有降解作用。在UV/O₃条件下，甲醛的降解率大大提高，特别是在高浓度臭氧条件下，降解率高达63％。臭氧浓度增大，降解率增大；紫外光强度增大，降解效果提高；气体流量增大，降解率下降；湿度增大，降解率提高。对甲醛降解试验进行动力学研究，结果表明，光照强度和臭氧浓度增大，一级反应速率增大，提高臭氧浓度要比加强紫外强度更能促进甲醛的降解。     

Air Quality Modeling in the South Coast Air Basin of California: What Do the Numbers Really Mean?

Abstract

This study evaluates air quality model sensitivity to input and to model components. Simulations are performed using the California Institute of Technology (CIT) airshed model. Results show the impacts on ozone (O₃) concentration in the South Coast Air Basin (SCAB) of California because of changes in: (1) input data, including meteorological conditions (temperature, UV radiation, mixing height, and wind speed), boundary conditions, and initial conditions (ICs); and (2) model components, including advection solver and chemical mechanism. O₃ concentrations are strongly affected by meteorological conditions and, in particular, by temperature. ICs also affect O₃ concentrations, especially in the first 2 days of simulation. On the other hand, boundary conditions do not significantly affect the absolute peak O₃ concentration, although they do affect concentrations near the inflow boundaries. Moreover, predicted O₃ concentrations are impacted considerably by the chemical mechanism. In addition, dispersion of pollutants is affected by the advection routine used to calculate its transport. Comparison among CIT, California Photochemical Grid Model (CALGRID), and Urban Airshed Model air quality models suggests that differences in O₃ predictions are mainly caused by the different chemical mechanisms used. Additionally, advection solvers contribute to the differences observed among model predictions. Uncertainty in predicted peak O₃ concentration suggests that air quality evaluation should not be based solely on this single value but also on trends predicted by air quality models using a number of chemical mechanisms and with an advection solver that is mass conservative.     

低温等离子体氧化氨气影响因素及动力学研究

采用电晕放电低温等离子体处理模拟氨气恶臭气体,考察了输入功率、初始浓度、气体湿度、停留时间等因素对降解效果和能量效率的影响,同时对反应过程进行了动力学研究。研究表明,输入功率以及停留时间对氨气降解的影响是积极的,但能量效率随着两者的增加先增大后减小。氨气的降解率随着初始浓度的增加而降低,而能量效率随着输入功率的增加而增加。氨气降解率和能量效率均随着气体湿度的增加而增加,当气体湿度为45%时达到最大值,然而随着气体湿度的进一步增加,其降解率和能量效率反而降低。反应尾气中臭氧浓度随着输入功率的增加而不断升高,而氨气的存在却使臭氧浓度有不同程度的降低。对电晕放电低温等离子体处理NH3的反应动力学进行了分析,得到NH3的反应速率常数为kNH3=0.0707 m3/(W·h)。     

Degradation of diuron in aqueous solution by ozonation

Degradation of diuron [3-(3,4-dichlorophenyl)-1,1-dimethylurea] in aqueous solution and the proposed degradation mechanism of diuron by ozonation were investigated. The factors that affect the degradation efficiency of diuron were examined. The generated inorganic ions and organic acids during the ozonation process were detected. Total organic carbon removal rate and the amount of the released Cl^? increased with increasing ozonation time, but only 80.0% of the maximum theoretical concentration of Cl^? at total mineralization was detected when initial diuron concentration was 13.8 mg L^?1. For N species, the final concentrations of NO₃ ^? and NH₄ ⁺ after 60 min of reaction time were 0.28 and 0.19 mg L^?1, respectively. The generated acetic acid, formic acid and oxalic acid were detected during the reaction process. The main degradation pathway of diuron by ozonation involved a series of dechlorination-hydroxylation, dealkylation and oxidative opening of the aromatic ring processes, leading to small organic species and inorganic species. The degradation efficiency of diuron increased with decreasing initial diuron concentration. Higher pH value, more ozone dosage, additive Na₂CO₃, additive NaHCO₃ and additive H₂O₂ were all advantageous to improve the degradation efficiency of diuron.     

Effect of ozonization in degradation of trifluralin residues in aqueous and food matrices

Abstract

This study investigates the oxidation of trifluralin residues during ozonation in aqueous and food matrices (tomato). Domestic ozonation equipment with average production of 23.9?mg O₃ L^?1 h^?1 was used in the tests. Modern chromatographic systems (SPME-GC-IT/MS/MS and QuEChERS-GC-IT/MS/MS) were applied for extraction and detection of trifluralin residue in fortified samples of ultrapure water, tap water, superficial water and tomato fruit. The samples were submitted to the ozonation process during 0, 5, 10 and 20?min. Treatment at 5?min was able to degrade 71.5% of herbicide trifluralin in surface water. The removal (%) in ultrapure water reached 83.4% after 20?min of ozonation. The degradation of trifluralin in fortified tomato samples (0.025–0.1?mg kg^?1) were conducted with ozonation at 20?min, and it ranged from 84.4 to 92.7%. After treatment, levels of trifluralin in tomato remained within the established MRLs to EU, USEPA and ANVISA (Brazil). The data provided evidence that ozone is effective for removing trace trifluralin from water and foods.     

A Re-Examination of Ambient Air Ozone Monitor Interferences

Abstract

Attaining the National Ambient Air Quality Standard (NAAQS) for ozone (O₃) could cost billions of dollars nationwide. Attainment of the NAAQS is judged on O₃ measurements made by the Federal Reference Method (FRM), ethylene chemiluminescence, or a Federal Equivalent Method (FEM), predominantly ultraviolet (UV) absorption. Starting in the 1980s, FRM monitors were replaced by FEMs so that today virtually all monitoring in the United States uses the UV methodology. This report summarizes a laboratory and collocated ambient air monitoring study of interferences in O₃ monitors. Potential interferences examined in the laboratory included water vapor, mercury, o-nitrophenol, naphthalene, p-tolualdehyde, and mixed reaction products from smog chamber simulations of urban atmospheric photochemistry. UV absorption O₃ monitors modi?ed for humidity equilibration were also collocated with UV FEM O₃ monitors at six sites in Houston, TX, during the 2007 summer O₃ season. The results suggest that humidity and interfering species can positively bias (overestimate) O₃ measured by FEM monitors used to determine compliance with the O₃ standards. The results also suggest that humidity equilibration can mitigate this bias.     

Ozone facilitated degradation of caffeine using Ce-TiO2 catalyst

The ozone initiated oxidation of 1,3,7-trimethylxanthine (caffeine), commonly found in wastewaters as model compound is reported using cerium (Ce)/titanium dioxide (TiO₂) as catalyst. The effect of pH and loading of ceria on titania were investigated. Effect of reaction conditions on degradation of caffeine based on their pseudo first-order rate constants were compared. The combination of catalyst Ce-TiO₂ and ozone aeration significantly enhanced the degradation of caffeine compared to uncatalysed ozonation. The oxidation of caffeine ensued via the free radical mechanism, through enhanced ozone decomposition into OH radicals. Ce/TiO₂(0.5?wt%) showed good activity in degradation of caffeine at pH 6, in both natural stream and river water samples showing about 60% total organic carbon removal in 2?h ozonation period. Using liquid chromatography-mass spectroscopy, degradation products were analysed. A reaction intermediate and one final product were positively identified. Nano-catalysts with different loadings of Ce on TiO₂ synthesized by sol-gel route were characterized by scanning electron microscope, transmission electron microscopy, BET and powder X-ray diffraction spectrum techniques. The results showed that the material retained a highly ordered mesoporous structure and possessed large surface area.     

Ecotoxicologial evaluation of wastewater ozonation based on detritus-detritivore interactions

Advanced oxidation technologies such as ozonation have been proposed to improve removal efficiency of micropollutants during wastewater treatment. In a meta-analysis of peer-reviewed literature, we found no ecotoxicological effects of wastewater ozonation on invertebrates (n = 82), but significant adverse effects on bacteria (n = 24) and fish (n = 5). As information on functional endpoints or trophic interactions is lacking, we applied a bioassay relating to leaf litter decomposition to fill this gap. Leaf discs exposed to ozone-treated wastewater with a high (1.04 mg O₃ (mg DOC)⁻¹, n = 49) ozone concentration were significantly preferred by an aquatic detritivore, Gammarus fossarum, over discs conditioned in wastewater not treated with ozone. This effect might have been mediated by reduced bacterial and elevated fungal biomass, and appears to be the first demonstration of wastewater ozonation impacts on invertebrates and an associated ecosystem process. In accordance with the food-choice trials, chemical analyses revealed significantly decreased concentrations of organic micropollutants in wastewater treated with ozone at high concentrations. Thus, food-choice trials as applied here hold promise to assess environmental effects of advanced oxidation technologies in wastewater treatment and appear to be a valuable complement to the ecotoxicological toolbox in general.