Vertical emission profiles for Europe based on plume rise calculations

The vertical allocation of emissions has a major impact on results of Chemistry Transport Models. However, in Europe it is still common to use fixed vertical profiles based on rough estimates to determine the emission height of point sources. This publication introduces a set of new vertical profiles for the use in chemistry transport modeling that were created from hourly gridded emissions calculated by the SMOKE for Europe emission model. SMOKE uses plume rise calculations to determine effective emission heights. Out of more than 40 000 different vertical emission profiles 73 have been chosen by means of hierarchical cluster analysis. These profiles show large differences to those currently used in many emission models. Emissions from combustion processes are released in much lower altitudes while those from production processes are allocated to higher altitudes. The profiles have a high temporal and spatial variability which is not represented by currently used profiles.     

Dependence of the Wind Profile Power Law on Stability for Various Locations

Recent environmental regulations have increased the need for construction of meteorological towers at power generation facilities. Due to practical and economic considerations, tower heights are usually lower than effluent release heights. At heights where wind speed data are not available, the wind speed is usually estimated from the measured wind speed using the %th wind profile power law and assuming neutral stability conditions. This study examines published data for many locations and shows that the %th wind profile power law is often unrepresentative of actual conditions because the degree of variation of wind speed with height depends greatly on atmospheric stability. The frequency of neutral stability conditions also varies appreciably by site. These two considerations are especially important in dispersion models which extrapolate wind speed at stack height from low level wind speed data.     

An Efficient Gaussian-Plume Multiple-Source Air Quality Algorithm

The information presented in this paper is directed to air pollution scientists with an interest in applying air quality simulation models. RAM is the three letter designation for this efficient Gaussian-plume multiple-source air quality algorithm. RAM is a method of estimating short-term dispersion using the Gaussian steady-state model. This algorithm can be used for estimating air quality concentrations of relatively stable pollutants for averaging times from an hour to a day in urban areas from point and area sources. The algorithm is applicable for locations with level or gently rolling terrain where a single wind vector for each hour is a good approximation to the flow over the source area considered. Calculations are performed for each hour. Hourly meteorological data required are wind direction, wind speed, stability class, and mixing height. Emission information required of point sources consists of source coordinates, emission rate, physical height, stack gas volume flow and stack gas temperature. Emission information required of area sources consists of south-west corner coordinates, source area, total area emission rate and effective area source height. Computation time is kept to a minimum by the manner in which concentrations from area sources are estimated using a narrow plume hypothesis and using the area source squares as given rather than breaking down all sources to an area of uniform elements. Options are available to the user to allow use of three different types of receptor locations: 1 ) those whose coordinates are input by the user, 2) those whose coordinates are determined by thé model and are downwind óf significant point and area sources where maxima are likely to occur, and 3) those whose coordinates are determined by the model to give good area coverage of a specific portion of the region. Computation time is also decreased by keeping the number of receptors to a minimum.     

APCA Financial Statements for 1975-1976

Abstract

A wind tunnel study was completed to determine the effects the presence of a parapet and raised intake configurations have on the dilution of a pollutant between a rooftop stack and building intake. This study was the first to address the effects of building parapets and varying intake configurations. A study of this kind is desirable because it is common practice for architects to attempt to hide stacks with the use of a parapet in order to make industrial buildings more aesthetically pleasing. This is done with no thought to the effect it may have on the intended function of the stacks, which is dispersing gases away from the building to avoid contamination of ventilation air.

Three parapet configurations (no parapet and two different parapet heights) and two intake configurations (flush and raised) were investigated. The relative effects of the parapets and the raised intake configurations were also compared and contrasted for five stack heights, two stack locations, and four intake locations.

The parapets were found to produce a cavity zone that extends above the building's roof by as much as two times the physical height of the parapet; increasing stack height had little effect on dispersion until the stack extended beyond this cavity region. The independent use of the parapets and raised intake configuration decreased the number of dilutions occurring between stack and intake when compared to the no parapet and flush intake configurations in all cases. Also substantiated in this study is the widely accepted view that the effect of the parapet addition is to decrease the effective stack height by the parapet height itself.

The results of this investigation were then compared to existing wind tunnel-derived empirical models. The models tested were not able to predict the effects of varying stack height and of varying the relative distance between stack and intake on the dilution of a pollutant between stack and intake under the tested configurations.     

Atmospheric emission of polychlorinated biphenyls from multiple industrial thermal processes

In this study, field measurements were conducted to estimate and characterize the atmospheric emission levels and profiles of polychlorinated biphenyls (PCBs) from multiple industrial thermal processes. The emission levels and profiles of PCBs from five types of thermal processes at twenty-three plants were studied and compared with eight processes reported in our previous studies. Correlation analysis was preformed to identify a marker congener for emission of ΣPCB. A significant correlation was observed between congener CB-118 and ΣPCB (R² = 0.65 and p < 0.01), which suggests that CB-118 is a good marker congener for emission of ΣPCB. The profiles of PCBs emitted from the thirteen thermal processes were compared, and this information could be used for studying source–receptor relationships and identifying the specific sources of PCBs. To prioritize the sources for control, the concentrations of PCBs from thirteen industrial thermal sources were compared. The PCB concentrations from secondary zinc smelting and thermal wire reclamation were about one to three order magnitude higher than those of other sources, which suggests that these two sources be given priority in PCB source control. Finally, the atmospheric emission factors of PCBs from the thirteen industrial sources were summarized, and these data will be useful for developing an integrated emission inventory of PCBs.     

Spatial surrogates for the disaggregation of CORINAIR emission inventories

CORINAIR atmospheric emission inventories are frequently used input data for air quality models with a domain situated in Europe. In CORINAIR emission inventories, sources are broken down over 11 major source categories. This paper presents spatial surrogates for the disaggregation of CORINAIR atmospheric emission inventories for input of air pollutants and particulate matter to grid or polygon based air quality model domains inside Europe. The basis for the disaggregation model was the CLC2000 land cover data to which statistical weights were added. Weights were population census data for residential emissions, employment statistics for agricultural and industrial area emissions, livestock statistics for ammonia emissions and annual aircraft movements for emissions realized by air transport. Additional road and off-road network information was used to disaggregate emissions realized by traffic. A comparison of top down produced emission estimates with spatially resolved national emission data for The Netherlands and the United Kingdom gave confidence in the present spatial surrogates as a tool for the top down production of atmospheric emission maps. Explained variance at a spatial resolution of 5 km was >70% for CO, NMVOC and NO_x, >60% for PM10 and almost 50% for SO₂.     

The Stack Height Requirements Implicit In the Federal Standards of Performance For New Stationary Sources

The promulgation of Federal standards of performance for certain classes of new stationary sources requires that such sources have minimum stack heights to meet also the requirements of national air quality standards. The determination of minimum stack height is complicated by the fact that the performance and air quality standards are stated on different averaging time bases; that the extent of preemption of the assimilative capacity of the air by any individual source will vary among jurisdictions and, in some cases, among different geographic areas of a single jurisdiction; and that some new sources will be designed to emit appreciably less than the performance standard requirement. However, these complications can be resolved and equations and charts prepared from which minimum stack height can be selected.     

机动车污染排放模型研究综述

过去几十年,为了掌握机动车污染排放的规律和特征,向决策者提供科学有效的机动车污染控制措施,研究者们致力于研究机动车污染物排放的物化原理和影响机动车污染的主要因素,并据此建立多种尺度的机动车排放模型,以模拟城市区域或者街道的污染物排放.为了分析机动车的瞬态排放特征,目前的机动车排放模型研究正逐渐从宏观向微观发展,排放测试方法注重获取逐秒的排放数据,排放模型模拟的时间尺度和空间尺度逐步趋向微观.此外,机动车模型研究正趋向与交通模型进行耦合,从而揭示机动车在实际道路交通流中的排放特征.从机动车排放的主要影响因素、机动车排放测试、机动车排放因子模型及机动车排放清单等4个方面综述了国内外机动车排放研究现状和发展动向,对比并评价各种机动车排放模型方法的优缺点和适用范围,对我国的机动车排放模型发展方向进行了展望.     

Mesoscale modeling of wintertime particulate matter episodes in eastern Washington, USA

The Spokane, Washington area is classified as a non-attainment area for the 24-h PM₁₀ standard due to a history of high particulate matter concentrations. A Eulerian regional air quality model (CALMET/CALGRID) has been used to characterize the emission, transport and dispersion of PM₁₀ and PM_2.5 in Spokane. Observations from a residential site (Rockwood, RW) and an industrial site (Crown Zellerbach, CZ), spanning July 1994–August 1996 were used to evaluate the current emission inventory. Two major tasks were devised to conduct the objectives of this investigation. First, a simple and efficient urban dispersion model (WYNDValley) was used to simulate important episodes characterized by the highest PM₁₀ and PM_2.5 concentrations. The selected episodes included four days with wet conditions for which no roads would have been emitting and seven days with dry conditions for which roads would emit. In the second step, a single road-emitting event was selected from the previous predicted results for further analysis using the Eulerian regional air quality model to examine the emission inventory. The urban and regional models predicted the observed concentration distributions reasonably well for the source emissions inventoried in Spokane. The mass concentrations of PM₁₀ were well predicted for the roads emitting case examined by both models indicating that the emission inventory based primarily upon area sources including roads is reasonably well characterized, at least at the RW site. The area sources around CZ are less well characterized, so that the PM₁₀ concentrations are underpredicted at CZ. The models appear unable to reach an equilibrium mass balance status at the beginning of the simulation, and the urban model seems unable to properly resolve the nocturnal boundary layer.     

Portuguese inventory of dioxins and furans atmospheric emissions

This article presents the results of the most recent estimation of polychlorinated dibenzo-p-dioxins (PCDD) and dibenzofurans (PCDF) atmospheric emissions in Portugal, which has covered the period 2004–2009 and includes 27 emission sources types. The results are compared with previous emissions inventories published for Portugal. The main objective of this work is to provide relevant information about the amounts of the compounds that are released into the atmosphere in Portugal, and identify their major sources and trends.