生物膜电极反应器降解苯胺的研究

生物膜电极反应器是结合生物膜法和电催化技术而发展的新型废水处理技术.研究了生物膜电极上的苯胺降解,对电流强度、温度、葡萄糖协同作用等因素的影响进行了观察.结果表明,生物膜电极反应器最高的电流强度为5 mA,运行的最适温度为36 ℃.葡萄糖对苯胺的生物膜电极降解的协同作用在进水COD为2 000 mg/L后达到最大.色谱/质谱联用检测苯胺降解中间产物为4-羟基-α-氨基戊酸.生物膜电极上的苯胺降解在阴极发生,降解开环途径与常规降解途径不同.     

微波辅助光催化降解氯酚类污染物的研究

研究了溶液中4-氯酚(4CP)、2-氯酚(2CP)、4-氯-3-甲基酚(4C3MP)、2,4-二氯酚(2,4-DCP)、2,4,6-三氯酚(2,4,6-TCP)和五氯酚(PCP)的微波辅助光催化降解(MW/PCO).结果表明,6种氯酚(CPs)光降解速率与分子中Cl原子取代的数目、位置等分子结构性质有关,单氯酚比多取代氯酚易光解.MW/PCO降解4CP的主要中间产物为苯酚、氯苯、对苯醌、对苯二酚等,降解PCP的主要中间产物为2,3,5,6-四氯对苯醌、2,3,4,6-四氯对苯二酚、四氯酚.CPs降解的机制是紫外光降解和羟基自由基 (·OH)亲电子加成脱氯过程.     

氯苯类化合物的生物降解

氯苯类生物降解机制可分为三类:氧化脱氯、还原脱氯和共代谢.氯苯类的氯化脱氯机制基本遵循一个相似的降解途径,即首先在双氯化酶攻击下形成二醇,此二醇脱氢形成氯代邻二酚.邻二酚开环产物是相应的氯化粘康酸,脱氯过程发生在此粘康酸内酯化过程中和内酯开环后;还原脱氯需要多种微生物共同参与,脱氯途径很不一样,这与不同微生物种群和不同的环境条件有关;共代谢作用降低了氯苯类化合物的生物毒性,使其更易为别的微生物同化.     

氯苯类化合物的生物降解

氯苯类生物降解机制可分为三类;氧化脱氯、还原脱氯和共代谢。氯苯类的氯化脱氯机制基本遵循一个相似的降解途径,即首先在双氧化酶攻击焉基层一醇,此二脱氯形成氯代邻二酚,邻二酚开环产物是相应的氯化粘康酸,脱氯过程发生在此粘康酸内酯化过程中和内酯开环后;还原脱氯需要多种微生物共同参与,脱氯途径很不一样,这与不同微生物种群和不同的环境条件有关,共代谢作用降低了氯苯类化合物的生物毒性,使其更易为别的微生物同化。     

钒基催化剂降解氯苯的原位红外分析

V_2O_5-WO_3/TiO_2催化剂被广泛应用于脱硝,且由于V_2O_5抗氯中毒能力强,对于氯代挥发性有机物(CVOCs)的催化降解也具有较好效果。通过浸渍法制备了不同V_2O_5和WO_3含量的负载型催化剂,采用氯苯作为CVOCs的模型化合物,对催化剂进行了活性评价和原位红外实验研究,在分子层面明确V_2O_5和WO_3在氯苯催化氧化过程中的作用。结果表明:增加V_2O_5含量是提高催化剂活性和稳定性的关键;氯苯在不同活性组分上的降解途径类似,均为苯环逐渐氧化开环及后续中间产物的氧化过程;V_2O_5对氯苯具有较强的氧化能力,在100℃即可观察到大量中间产物,且随着温度的升高,中间产物可迅速被氧化分解。相对而言,WO_3的氧化性能很差,仅在温度达到300℃才可明显观察到中间产物,但V_2O_5和WO_3之间存在协同作用。以上分子层面的反应机制研究,有助于明确催化剂各组分的具体作用,进一步指导开发性能更好的钒基催化剂,用于CVOCs的催化氧化。     

超声波-光催化氧化降解邻氯苯酚的研究

对超声波-光催化氧化降解邻氯苯酚(2-cp)进行了研究,探讨了溶液初始pH值、TiO2投加量、H2O2投加量和溶液初始浓度对邻氯苯酚降解率的影响.并对几种不同处理方法降解邻氯苯酚的结果进行了对比.结果表明,超声波和紫外光的协同效果明显,在相同的反应时间内,超声波能够明显提高光催化降解邻氯苯酚的降解率.超声波和紫外光连用,具有良好的工业应用前景.     

球形红细菌好氧降解氯代苯研究

采用光合细菌球形红细菌在好氧条件下对氯代苯进行生物降解.结果表明,氯代苯不能作为球形红细菌生长的惟一碳源和能源,球形红细菌好氧降解氯代苯是在适宜碳源存在下以共代谢的方式进行;根据分析细胞提取液中双加氧酶活性和代谢中间产物,推断出其降解机制为邻位裂解途径,按先开环再脱氯过程进行,邻苯二酚1,2-双加氧酶的活性可以通过氯代...     

1，4-二氯苯降解菌的分离及其降解特性研究

从某污水处理曝气池的活性污泥中分离出一株能够以1，4-二氯苯为唯一碳源和能源生长的菌株DEB-1，通过形态特征和生理生化试验初步鉴定为黄杆菌属（Flavobacterium sp.）。实验结果表明，该菌株最适降解温度为32℃、最适降解pH为7.8，24 h对100 mg/L的1，4-二氯苯的降解率达94.5%。菌株DEB-1的降解谱较广，对5种氯苯类物质具有较高的降解率。并进一步研究了DEB-1的1，4-二氯苯降解酶粗酶液的性质，其最适反应温度和pH分别为30℃和8.5。对处理含氯代芳香化合物的有机废水具有一定的意义。     

超声波降解水中的氯苯

考察了用超声波降解水中氯苯的可行性、动力学、产物和TOC变化。在 2 0kHz和 4 0W的超声波作用下 ,氯苯的一级降解常数为 0 0 5 /min。随着所加超声功率的增高 ,氯苯降解常数呈线性增加。 30min内超声脱氯效率达到 6 6 % ,TOC去除达到 4 3%。     

超声波降解水中的氯苯

考察了用超声波降解水中氯苯的可行性、动力学、产物和TOC变化。在20kHz和40w的超声波作用下，氯苯的一级降解常数为0．05／min。随着所加超声功率的增高，氯苯降解常数呈线性增加。30min内超声脱氯效率达到66％,TOC去除达到43％。     

Liquid chromatographic aqueous product characterization of high-energy electron beam irradiated 2-chlorobiphenyl solutions

Polychlorinated biphenyls (PCBs) are of environmental concern due to their toxic nature. Ionizing radiation has been suggested as a means to remediate PCB-contaminated samples in complex matrices. A set of experiments was performed to qualitatively and quantitatively determine the aromatic degradation products of 2-monochlorobiphenyl (2-MCB) in an aqueous system exposed to ionizing radiation. The degradation of 2-MCB was observed in aqueous samples that were exposed to radiation from a linear accelerator electron beam source. Analytical measurements performed by liquid chromatography (LC) equipped with an ultraviolet (UV) detector revealed that biphenyl, o-hydroxybiphenyl, p-hydroxybiphenyl, phenol, chlorobenzene, and other unidentified products were created after 2-MCB irradiation. These results suggest that sensitive and selective analytical methods will be required to account for all degradation products during ionizing radiation of aqueous PCB-contaminated samples.     

Chemical identification and acute biotoxicity assessment of gaseous chlorobenzene photodegradation products

In order to evaluate the ecological safety and feasibility of UV photodegradation processes for the treatment of halogenated aromatic hydrocarbons, the chemical composition and acute biotoxicity of gaseous chlorobenzene photodegradation products were investigated. Results showed that the main products of chlorobenzene photodegradation included hydrochloric acid, acetic acid, formic acid, phenol and chlorophenol. Roughly 64% of the removed chlorobenzene was converted into phenol, making it the most significant product formed. The types of byproducts suggested that two distinct reaction pathways might compete during the photodegradation process. Interestingly, it appeared that one of these pathways did not involve the direct photocatalytic oxidation of chlorobenzene. An acute biotoxicity assay measuring the inhibition of bioluminescence indicated that gaseous exhaust with overall higher toxicity was emitted after UV irradiation. The acute toxicity of the UV reactor exhaust gas was as high as EC(50)=13.5mg-Zn(2+)m(-3-)-gas. The increased toxicity mainly resulted from the conversion of chlorobenzene to more soluble toxic products and ozone production during the photodegradation process.     

Toxicity and biodegradability of sulfonamides and products of their photocatalytic degradation in aqueous solutions

The photocatalytic degradation of sulfacetamide, sulfathiazole, sulfamethoxazole and sulfadiazine in water solutions during their illumination of UV radiation (lambda(max) 366 nm) with TiO2 catalyst was examined. The growth-inhibition effect of sulfonamides and intermediate products theirs photodegradation was investigated in aqueous solution with the green alga Chlorella vulgaris. The biodegradability of the investigated compounds was determined in the illuminated solutions and is expressed as Biochemical Oxygen Demand. It was found that all of the investigated sulfonamides in the initial solutions were resistant to biodegradation and were toxic relative to C. vulgaris. The toxicity (EC50 values) relative to C. vulgaris increased in the following order sulfacetamide, sulfathiazole, sulfamethoxazole, sulfadiazine. All of the investigated sulfonamides undergo photocatalytic degradation. The toxicity of intermediate products of the sulfonamides degradation was significantly lower than the toxicity of sulfonamides in the initial solutions and was dependent on illumination time and degradation rate. The intermediate products of photocatalysis in contrast to the initial sulfonamides, might be mineralized using biological methods.     

超声波及其联用技术降解废水中的氯苯

研究了在降解含氯苯废水的过程中，超声波分别与H2O2、O2、空气联用对氯苯降解效率的影响。结果表明，超声波分别与H2O2、O2、空气联用比单独使用超声波降解效率分别提高40、30、18个百分点。并且随H2O2用量的增加，降解效率明显升高。对于O2、空气，当气体流量小于0．3754mL／s时，降解效率随O2、空气流量的增大而明显升高。     

Degradation of polychlorinated dibenzo-p-dioxins in aqueous solution by Fe(II)/H2O2/UV system

The photodegradation of polychlorinated dibenzo-p-dioxins (PCDDs), which include tetra- to octa-CDDs (TeCDD, PeCDD, HxCDD, HpCDD and OCDD), was carried out in the presence of Fe(II) and H2O2 mixed reagent. The degradation efficiency was strongly influenced by UV irradiation, and the initial concentrations of H2O2 and Fe(II). An initial TeCDD concentration of 10 ng l(-1) was completely degraded within 20 min under the optimum conditions. All PCDDs tested were successfully degraded by Fe(II)/H2O2/UV treatment and complete degradation of TeCDD, PeCDD and HxCDD was achieved within 120 min. PCDD photodegradation rates decreased with the number of chlorine atoms. The degradation process of TeCDD by this system seems to be initiated by an oxidative reaction (OH* radical attack) because less chlorinated DDs as intermediate products were not detected. From the Frontier electron density calculation, the first OH* radical attack positions on TeCDD were found to be four C atoms neighboring two O atoms. The decomposition of TeCDD gave 4,5-dichlorocatechol as an intermediate product. A TeCDD degradation scheme was proposed based on the identified intermediate and the values of Frontier electron density. Based on these results, Fe(II)/H2O2/UV system could be useful technology for the treatment of wastewater containing persistent pollutants such as dioxins and polychlorinated biphenyls.     

Reaction pathways of dimethyl phthalate degradation in TiO2-UV-O2 and TiO2-UV-Fe(VI) systems

The photocatalytic degradation of dimethyl phthalate (DMP) in aqueous TiO₂ suspension under UV illumination has been investigated using oxygen (O₂) and ferrate (Fe(VI)) as electron acceptors. The experiments demonstrated that Fe(VI) was a more effective electron acceptor than O₂ for scavenging the conduction band electrons from the surface of the catalyst. Some major intermediate products from DMP degradation were identified by HPLC and GC/MS analyses. The analytical results identified dimethyl 3-hydroxyphthalate and dimethyl 2-hydroxyphthalate as the two main intermediate products from the DMP degradation in the TiO₂–UV–O₂ system, while in contrast phthalic acid was found to be the main intermediate product in the TiO₂–UV–Fe(VI) system. These findings indicate that DMP degradation in the TiO₂–UV–O₂ and TiO₂–UV–Fe(VI) systems followed different reaction pathways. An electron spin resonance analysis confirmed that hydroxyl radicals existed in the TiO₂–UV–O₂ reaction system and an unknown radical species (most likely an iron–oxo species) is suspected to exist in the TiO₂–UV–Fe(VI) reaction system. Two pathway schemes of DMP degradation in the TiO₂–UV–O₂ and TiO₂–UV–Fe(VI) reaction systems are proposed. It is believed that the radicals formed in the TiO₂–UV–O₂ reaction system preferably attack the aromatic ring of the DMP, while in contrast the radicals formed in the TiO₂–UV–Fe(VI) reaction systems attack the alkyl chain of DMP.     

Relationship between the ATP content of subsurface material and the rate of biodegradation of alkylbenzenes and chlorobenzene

The rate of biotransformation of toluene in unconsolidated subsurface material from sites at Lula, Oklahoma, and Conroe, Texas, was compared to the ATP (adenosine triphosphate) content of these materials. The rate of toluene degradation decreased with decreasing ATP content. When ATP contents were at or less than 0.05 ng g⁻¹, biotransformation of toluene could not be detected (less than 1% of the initial concentration was degraded per week). At intermediate concentrations of ATP, 0.37 and 0.16 ngvg⁻¹, the rates of toluene degradation were 18 ± 4.5% and 25 ± 10% of the initial concentration per week. At ATP concentrations above 1 ng g⁻¹, the rates of toluene degradation exceeded 90% of the initial concentration per week. There was no simple relationship between ATP content and chlorobenzene degradation. Subsurface material that had been exposed to creosote wastes, and which degraded toluene rapidly, also degraded benzene, o-xylene, and m-xylene.     

Experimental study on the thermal oxidation of 2-chlorophenol in air over the temperature range 450-900 degrees C

The thermal oxidation of 2-chlorophenol (2-CP) in air was investigated using a perfectly stirred reactor at 1 atm over the temperature range 450–900 °C. The relative concentration of 2-CP was 1000 ppmV (equivalence ratio Φ = 0.03). About fifty organic products were identified as trace species. The concentration profiles of 2-CP, carbon oxides as well as those of seventeen major organic intermediates and six non-to-lower chlorinated dioxins and furans were presented as a function of temperature for a residence time of 2 s. The most abundant intermediate products were carbon monoxide, 2 H-pyran-2-one, chlorobenzene, 4-cyclopenten-1,3-dione, phenol, benzofuran, 2-chlorohydroquinone and 2-indanone. These concentration profiles have revealed that temperatures of at least 900 °C were needed to completely oxidize 2-CP, CO and all other organic byproducts to carbon dioxide. Reaction pathways accounting for the formation of most observed products are proposed.