Bioavailability of zinc in runoff water from roofing materials

Corrosion and runoff from zinc-coated materials and outdoor structures is an important source for the dispersion of zinc in the environment. Being part of a large inter-disciplinary research project, this study presents the bioavailability of zinc in runoff water immediately after release from the surface of 15 different commercially available zinc-based materials exposed to the urban environment of Stockholm, Sweden. Runoff water was analysed chemically and evaluated for its possible environmental impact, using both a biosensor test with the bacteria Alcaligenes eutrophus (Biomet^®) and the conventional 72 h growth inhibition test with the green alga Raphidocelis subcapitata. Chemical speciation modelling revealed that most zinc (94.3–99.9%) was present as the free Zn ion, the most bioavailable speciation form. These findings were confirmed by the results of the biosensor test (Biomet^®) which indicated that all zinc was indeed bioavailable. Analysis of the ecotoxicity data also suggested that the observed toxic effects were due to the presence of Zn²⁺ ions. Finally, regression analysis showed that, for this type of runoff samples, the rapid screening biosensor was capable of predicting (a) the total amount of zinc present in the runoff samples (R² of 0.93–0.98; p<0.05) and (b) the observed 72 h-EbC₅₀s (R² of 0.69–0.97; p<0.05).     

In vitro studies of copper release from powder particles in synthetic biological media

The aim of this paper is to provide quantitative data on copper release from powder particles of different copper materials, including artificial copper patina, Cu(2)O and metallic Cu, when exposed to different synthetic biological media to simulate an inhalation scenario and/or skin contact. Generated data may contribute in risk assessment of potential health effects following exposure to and handling of various copper materials. All tests were performed in vitro to determine total copper concentrations, release rates of total copper, and to elucidate its time-dependence. The copper release process was interpreted in terms of specific surface area, surface morphology-, and composition. All powder materials show a time-dependent release process with total copper release rates less than 3 microg/cm(2) per hour at steady state conditions, for all media investigated. The importance of using relevant test media when simulating different interstitial lung conditions and difficulties encountered when comparing powder particles of essentially different properties are thoroughly discussed.     

Speciation distribution and mass balance of copper and zinc in urban rain, sediments, and road runoff

Heavy metal pollution in road runoff had caused widespread concern since the last century. However, there are little references on metal speciation in multiple environmental media (e.g., rain, road sediments, and road runoff). Our research targeted the investigation of metal speciation in rain, road sediments, and runoff; the analysis of speciation variation and mass balance of metals among rain, road sediments, and runoff; the selection of main factors by principal component analysis (PCA); and the establishment of equation to evaluate the impact of rain and road sediments to metals in road runoff. Sequential extraction procedure contains five steps for the chemical fractionation of metals. Flame atomic absorption spectrometry (Shimadzu, AA-6800) was used to determine metal speciation concentration, as well as the total and dissolved fractions. The dissolved fractions for both Cu and Zn were dominant in rain. The speciation distribution of Zn was different from that of Cu in road sediments, while speciation distribution of Zn is similar to that of Cu in runoff. The bound to carbonates for both Cu and Zn in road sediments were prone to be dissolved by rain. The levels of Cu and Zn in runoff were not obviously influenced by rain, but significantly influenced by road sediments. The masses for both Cu and Zn among rain, road sediments, and road runoff approximately meet the mass balance equation for all rainfall patterns. Five principal factors were selected for metal regression equation based on PCA, including rainfall, average rainfall intensity, antecedent dry periods, total suspended particles, and temperature. The established regression equations could be used to predict the effect of road runoff on receiving environments.     

Incorporating bioavailability into management limits for copper in sediments contaminated by antifouling paint used in aquaculture

Although now well embedded within many risk-based sediment quality guideline (SQG) frameworks, contaminant bioavailability is still often overlooked in assessment and management of contaminated sediments. To optimise management limits for metal contaminated sediments, we assess the appropriateness of a range methods for modifying SQGs based on bioavailability considerations. The impairment of reproduction of the amphipod, Melita plumulosa, and harpacticoid copepod, Nitocra spinipes, was assessed for sediments contaminated with copper from antifouling paint, located below aquaculture cages. The measurement of dilute acid-extractable copper (AE-Cu) was found to provide the most useful means for monitoring the risks posed by sediment copper and setting management limits. Acid-volatile sulfide was found to be ineffective as a SQG-modifying factor as these organisms live mostly at the more oxidised sediment water interface. SQGs normalised to %-silt/organic carbon were effective, but the benefits gained were too small to justify this approach. The effectiveness of SQGs based on AE-Cu was attributed to a small portion of the total copper being present in potentially bioavailable forms (typically <10% of the total). Much of the non-bioavailable form of copper was likely present as paint flakes in the form of copper (I) oxide, the active ingredient of the antifoulant formulation. While the concentrations of paint-associated copper are very high in some sediments, as the transformation of this form of copper to AE-Cu appears slow, monitoring and management limits should assess the more bioavailable AE-Cu forms, and further efforts be made to limit the release of paint particles into the environment.     

Molecular study of concentrated copper pollutant with a compost

Humic substance in compost contains various organic functional groups that can sorb metal ions through ionic force. This study used thermal treatment technology to concentrate copper in the heated residues while destroying the humic substance of copper-sorbed kitchen compost. Scanning electron microscopy (SEM) results show that copper clusters were formed in the heated residues. Information from both X-ray diffraction (XRD) patterns and Cu K-edge X-ray absorption spectroscopy (XAS) spectrum indicates that about 30% of the doped Cu(II) was chemically reduced to Cu(I) and Cu(0) when the sample was heated at 500 and 900 degrees C for 2h. The XAS results indicate that after 500 degrees C thermal treatment, the loaded Cu(NO(3))(2) was transformed into CuO (ca. 54%), Cu (ca. 18%), Cu(OH)(2) (ca. 15%), and Cu(2)O (ca.13%). Heating at 900 degrees C caused more transformation into elemental Cu probably due to more release of oxygen.     

Impacts of pH and ammonia on the leaching of Cu(II) and Cd(II) from coal fly ash

Many coal-fired power plants are implementing ammonia-based technologies to reduce NO(x) emissions. Excess ammonia in the flue gas often deposits on the coal fly ash. Ammonia can form complexes with many heavy metals and change the leaching characteristics of these metals. This research tends to develop a fundamental understanding of the ammonia impact on the leaching of some heavy metals, exemplified by Cu(II) and Cd(II), under different pH conditions. Batch results indicated that the adsorption is the main mechanism controlling Cu(II) and Cd(II) leaching, and high concentrations of ammonia (>5,000 mg/l) can increase the release of Cu(II) and Cd(II) in the alkaline pH range. Based on the chemical reactions among fly ash, ammonia, and heavy metal ion, a mathematical model was developed to quantify effects of pH and ammonia on metal adsorption. The adsorption constants (logK) of Cu(2+), Cu(OH)(+), Cu(OH)(2), and Cu(NH(3))(m)(2+) for the fly ash under investigation were respectively 6.0, 7.7, 9.6, and 2.9. For Cd(II), these constants were respectively 4.3, 6.9, 8.8, and 2.6. Metal speciation calculations indicated that the formation of less adsorbable metal-ammonia complexes decreased metal adsorption, therefore enhanced metal leaching.     

Changes of copper speciation in maize rhizosphere soil

Chemical forms of copper in the rhizosphere and bulk soil of maize were investigated using rhizobox cultivation and sequential extraction techniques. The copper accumulations were also determined. The results demonstrated that there were continuous changes in copper fractionation within the maize rhizosphere. Initially, the amount of exchangeable copper increased before dropping below the initial level after 40 days or so. Carbonate associated copper followed a similar trend of change, but with a slower pace than the exchangeable copper. The increase in carbonate associated copper only become evident after 30 days, with the net loss occurring after 60 days. There were also initial increases in oxide bound copper as well as decreases in the organic matter associated copper, both followed by a turnover after 40-50 days. The accumulation of copper in the maize plant was found to be biomass dependent. The amount of accumulated copper absorbed in the plant material exceeded the initial quantity of the exchangeable copper in the soil, revealing a transformation from less bioavailable to more bioavailable fractions. During cultivation, decreases in redox potential and increases in pH, dissolved organic carbon (DOC), and microbial activity in the maize rhizosphere were observed. The change in copper speciation may result from root-induced changes in DOC, redox potential, and microbial activity in the rhizosphere.     

Circulation of copper in the biotic compartments of a freshwater dammed reservoir

This study concerns a chronic copper release in an aquatic ecosystem: Mirgenbach reservoir; which is characterized by high salinity, conductivity and hardness, a eutrophic state and a high temperature. To study the bioavailability of copper in the biotic compartments, the sampling covered the entire food chain (phyto- and zooplankton, macroalgae, aquatic plants, crustaceans, mollusks, and fish). Of the organisms present, the filter feeder Dreissena polymorpha, the detritivorous Bithynia tentaculata and Orconectes limosus were most contaminated by copper. The level of copper found in fish was the lowest. Body copper concentrations recorded in the present study show large variability between species even in some that are closely related. In most cases, however, the metal handling strategy, feeding habits, morphology and ecology can, at least partially, explain the metal content recorded. Pollution factors have been used to assess the state of contamination of the food chain. This study showed finally that the copper in the lake is bioavailable and bioaccumulated by organisms up to high levels and some effects of long-term toxicity of copper on benthic community and planktonic biomass were pointed out.     

Speciation of zinc in contaminated soils

The chemical speciation of zinc in soil solutions is critical to the understanding of its bioavailability and potential toxic effects. We studied the speciation of Zn in soil solution extracts from 66 contaminated soils representative of a wide range of field conditions in both North America and Europe. Within this dataset, we evaluated the links among the dissolved concentrations of zinc and the speciation of Zn(2+), soil solution pH, total soil Zn, dissolved organic matter (DOM), soil organic matter (SOM) and the concentrations of different inorganic anions. The solid-liquid partitioning coefficient (K(d)) for Zn ranged from 17 to 13,100Lkg(-1) soil. The fraction of dissolved Zn bound to DOM varied from 60% to 98% and the soil solution free Zn(2+) varied from 40% to 60% of the labile Zn. Multiple regression equations to predict free Zn(2+), dissolved Zn and the solid-liquid partitioning of Zn are given for potential use in environmental fate modeling and risk assessment. The multiple regressions also highlight some of the most important soil properties controlling the solubility and chemical speciation of zinc in contaminated soils.     

Assessment of zerovalent iron for stabilization of chromium, copper, and arsenic in soil

Stabilization of soil contaminated with trace elements is a remediation practice that does not reduce the total content of contaminants, but lowers the amounts of mobile and bioavailable fractions. This study evaluated the efficiency of Fe(0) to reduce the mobility and bioavailability of Cr, Cu, As and Zn in a chromated copper arsenate (CCA)-contaminated soil using chemical, biochemical and biotoxicity tests. Contaminated soil was stabilized with 1% iron grit. This treatment decreased As and Cr concentrations in leachates (by 98% and 45%, respectively), in soil pore water (by 99% and 94%, respectively) and in plant shoots (by 84% and 95%, respectively). The stabilization technique also restored most of analyzed soil enzyme activities and reduced microbial toxicity, as evaluated by the BioTox test. After stabilization, exchangeable and bioaccessible fractions of Cu remained high, causing some residual toxicity in the treated soil.     

Fractionation and bioavailability of Cu in soil remediated by EDTA leaching and processed by earthworms (<Emphasis Type="Italic">Lumbricus terrestris</Emphasis> L.)

Background, aim, and scope  

Soil remediation with ethylenediamine tetraacetic acid (EDTA) leaching is capable of removing only part of the total metal concentration in the soil, mostly the labile, bioavailable metal species (metal bioavailability stripping). However, reintroduction of remediated soil in the environment exposes the soil to various environmental factors, which could potentially shift nonlabile residual metals back to labile bioavailable forms. We studied the effect of autochthonous earthworm species as model biotic environmental factor on the fractionation and bioavailability of Cu residual in soil after remediation.     

Particulate copper in soils and surface runoff from contaminated sandy soils under citrus production

Soil contamination by copper (Cu) is a worldwide concern. Laboratory incubation and soil Cu characterization were conducted to examine the effects of external Cu loading and liming on Cu speciation in both bulk soil and particulates of an Alfisol and Spodosol under citrus production. Also, drainage water from the sites was evaluated for dissolved and particulate forms of Cu. Soil available Cu estimated by CaCl₂, NH₄OAc, or Mehlich-3 extraction significantly increased with external Cu loads and decreased with soil pH. Most increases in soil Cu occurred in the exchangeable and oxide-bound fractions. Organically bound Cu was the dominant fraction in both bulk soil and particulates, but more in particulates than bulk soil (P?≤?0.001). Organically bound Cu was highly correlated with total recoverable Cu (P?≤?0.01), increased significantly with external Cu loads (P?≤?0.001), and decreased with soil pH (P?≤?0.05). Lime addition converted part of Cu from available pools to more stable forms. Organically bound Cu complexes were found to dominate in soil solution or surface runoff. These results indicate that most Cu accumulated in the contaminated soils is highly mobile, and thus may impact citrus production and the environment.     

Fate and bioavailability of arsenic in organo-arsenical pesticide-applied soils. Part-I: incubation study

A laboratory incubation study was conducted to estimate geochemical speciation and in vitro bioavailability of arsenic as a function of soil properties. Two chemically-variant soil types were chosen, based on their potential differences with respect to arsenic reactivity: an acid sand with minimal arsenic retention capacity and a sandy loam with relatively high concentration of amorphous Fe/Al-oxides, considered a sink for arsenic. The soils were amended with dimethylarsenic acid (DMA) at three rates: 45, 225, and 450 mg/kg. A sequential extraction scheme was employed to identify the geochemical forms of arsenic in soils, which were correlated with the "in vitro" bioavailable fractions of arsenic to identify the most bioavailable species. Arsenic bioavailability and speciation studies were done at 0 time (immediately after spiking the soils with pesticide) and after four-months incubation. Results show that soil properties greatly impact geochemical speciation and bioavailability of DMA; soils with high concentrations of amorphous Fe/Al oxides retain more arsenic, thereby rendering them less bioavailable. Results also indicate that the use of organic arsenicals as pesticides in mineral soils may not be a safe practice from the viewpoint of human health risk.     

Characterization of adsorbent composition in co-removal of hexavalent chromium with copper precipitation

Mechanisms of hexavalent chromium co-removal with copper precipitation by dosing Na2CO3 were studied with a series of well-designed batch tests using solutions containing 150 mg l-1 Cu(II) and 60 mg l-1 Cr(VI). It was found that direct precipitation of chromium through formation of copper-chromium bearing precipitates (in the form of CuCrO4) was one of the main mechanisms contributing to chromium co-removal at pH close to 5.0, and adsorption of chromium at a higher pH by freshly formed copper-carbonate precipitates (adsorbent) contributed to further chromium co-removal. Since, according to solubility products, neither copper-carbonate nor copper-hydroxide precipitates can be produced at pH around 5.0 for a pure 150 mg l-1 copper precipitation, characterization of copper-carbonate precipitates (adsorbent) was carried out through developing pC-pH curves of the systems by both equilibrium calculations and MINEQL+ 4.5 (a chemical equilibrium modeling software), and also through laboratory determination of the precipitate composition, such as gravimetric analyses, inorganic carbon percentage and EDAX spectrum analyses. CuCO3.Cu(OH)2, or a combination of CuCO3.Cu(OH)2 (in majority) and Cu(OH)2 (in minority) were suggested to be the major constituent of the precipitates obtained from the copper solution with Na2CO3 dosing.     

Copper activity in soil solutions of calcareous soils

Copper partitioning was studied in seven calcareous soils at moisture content corresponding to 1.2 times the field moisture content (soil water potential 7.84 J kg(-1)). Copper retention was accompanied by the release in soil solution of Ca(2+), Mg(2+), Na(+), and H(+), and the total amount of these cations released was 0.8 to 1.09 times the amount of Cu sorbed (mol(c):mol(c)). The relationships between Cu activity and pH, and the balance of cations in soils correspond with the surface precipitation of CuCO(3) as the main mechanism of Cu retention. The values of ion activity product of surface precipitate were close for all studied soils with the average log(IAP(CuCO(3)))=-15.51. The relationship between copper activity in soil solutions and soil properties is well fit by a regression relating pCu (-log copper ion activity) with soil pH, total Cu, and carbonate content.     

Evaluation of copper availability to plants in copper-contaminated vineyard soils

The repeated use of copper (Cu) fungicides to control vine downy mildew has led to long-term accumulation of Cu in vineyard soils which now raises the issue of the potential bioavailability of Cu for various living organisms including plant species. The bioavailable Cu can be defined as the portion of soil Cu that can be taken up by roots, for a given plant species. In order to evaluate the bioavailability of Cu to plants, a pot experiment was conducted in glasshouse conditions with a crop species (maize) and 12 soils sampled in the upper horizon of 10 vineyard plots (total Cu ranging from 38 to 251 mg kg-1) and two woodland plots (control soils that had not received any Cu application; total Cu amounting to 20-26 mg kg-1). These soils were selected for their diverse physical (large range of particle size distribution) and chemical (from acid to calcareous soils) properties. After 35 days of growth, plant shoots were harvested for analysis. The roots were separated from soil particles for further analysis. The concentrations of Cu in the roots and aerial parts of the maize were then compared with the amounts of Cu extracted from the soil by a range of conventional extractants. Observed Cu concentrations in maize roots which have grown in contaminated vineyard soils were very high (between 90 and 600 mg kg-1), whereas Cu concentrations in the aerial parts varied only slightly and remained low (< 18 mg kg-1). Root Cu concentrations observed for maize increased with increasing total Cu content in the soil and with decreasing soil CEC. Cu accumulation in maize roots may be as high in calcareous soils as in acid soils, suggesting that soil pH had little influence. In the case of the vineyard soils studied, the lack of correlation found for maize between Cu concentrations in roots and in the aerial parts, suggests that an analysis of the aerial parts would not be a good indicator of plant Cu uptake, as it provides no insight into the real amount of Cu transferred from the soil to the plant. For maize, our results show that extraction with organic complexing agents (EDTA, DTPA) and extraction with ammonium acetate seem to provide a reasonably good estimate of root Cu concentration.     

Effect of copper on soil functional stability measured by relative soil stability index (RSSI) based on two enzyme activities

Copper can affect essential processes in soils, often for long periods. Enzyme activity is considered a sensitive indicator to evaluate soil health and the potential toxic impact of a soil contaminant. Nevertheless, there is heterogeneity in the responses from enzyme activity assays because of the influence of pH and other physicochemical parameters on both enzyme activity and metal speciation. This leads to complications when comparing soils and limits the validity of the results. To overcome these problems, this paper evaluates resistance and recovery, quantified by using a relative soil stability index (RSSI), of the beta-glucosidase and protease activities towards an additional heat disturbance (17 h at 60 degrees C) in soils where soil organic matter, pH and Cu content were modified in a factorial setup. Chemical analyses (dissolved Cu, pCu(2+), dissolved organic carbon, pH) were performed both before the heat-perturbation and after the enzyme activity monitoring period. Results show that soil pH did not interfere with the RSSI scores of both enzymes. beta-glucosidase RSSI scores were scarcely affected by copper, making it inappropriate for evaluating copper-induced stress to soils. Protease activity shows stimulations of up to 2.5 times the activity of the unperturbed control in uncontaminated samples only. Thus, the protease RSSI score seems a good indicator for soil health relative to copper contamination given that all samples were affected by the presence of copper and high correlations were observed between RSSI scores and the different copper forms.     

Copper bioavailability in the rhizosphere of maize (Zea mays L.) grown in two Italian soils

In this study, potentially bioavailable copper was estimated in two soils (a fungicide polluted and a natural soil) using a passive sampling technique, DGT. As plants can alter copper mobility and bioavailability in the soil, the rhizosphere properties of Zea mays L. were investigated using rhizoboxes.

Compared to the total concentration, the soluble and the potentially bioavailable copper concentration in the bulk soils were generally low (less than 0.20% and 0.06% respectively), with a sixfold increase in the rhizosphere of the polluted soil. Our results suggest that maize cultivation in a polluted vineyard soil could increase the potentially available fraction of copper. DGTs showed a good sensitivity to soil properties and to root-induced changes in the rhizosphere, but the potentially bioavailable copper could not be related to the copper concentration in the above ground parts of maize. The results suggest that DGT may be used to predict some effects of the cultivation of polluted soils, for example, metal mobility and increased availability, but they cannot mimic the uptake of a tolerant plant.

For both soils, dissolved organic carbon (DOC) concentrations were threefold higher in the rhizosphere than in the bulk soil, whilst bioaccumulation in leaves and roots was not significant. DOC production, usually effective in ion mobilization and assimilation, may help also in the reduction of Cu uptake at toxic concentrations. The sequestration of available Cu in soil and soil solution by DOC seems to contribute to maize tolerance.     

Removal of Cu(II) from aqueous solution in a fluidized-bed reactor

In this study, a fluidized-bed reactor (FBR) was employed to treat copper-containing wastewater by mean of copper precipitation on the surface of sand grains. The conditions for optimum copper removal efficiency were also investigated. This technology was controlled so as to keep supersaturation low to induce the nucleated precipitation of copper coating on the sand surface in an FBR. The effects of relevant parameters, such as the pH value, the molar ratio of [C(T)] to [Cu(2+)], hydraulic loading and the types of chemical reagents used, were examined. The experimental results indicated that 96% copper removal efficiency could be achieved when the influent copper concentration was 10mg l(-1). The optimum chemical reagent was Na(2)CO(3); the molar ratio of [C(T)]/[Cu(2+)] was 2, and the optimal hydraulic loading was not be more than 25m h(-1). In addition, preventing homogeneous nucleation in the FBR was an important operation parameter. Homogeneous nucleation and molecular growth would lead to undesirable microparticle formation in the effluent. A good mixture of carbonate and copper in the presence of sand grains could reduce the level of homogeneous nucleation in the bottom of the reactor. Energy dispersive analysis (EDS) of X-rays provided insight into the copper coating on the sand surface, and element analysis indicated the weight percentages of CuCO(3) and Cu(OH)(2) in precipitate.     

Long-term dispersion and availability of metals from submarine mine tailing disposal in a fjord in Arctic Norway

Mining of Cu took place in Kvalsund in the Arctic part of Norway in the 1970s, and mine tailings were discharged to the inner part of the fjord, Repparfjorden. Metal speciation analysis was used to assess the historical dispersion of metals as well as their potential bioavailability from the area of the mine tailing disposal. It was revealed that the dispersion of Ba, Cr, Ni, Pb and Zn from the mine tailings has been limited. Dispersion of Cu to the outer fjord has, however, occurred; the amounts released and dispersed from the mine tailing disposal area quantified to be 2.5–10 t, less than 5% of Cu in the original mine tailings. An estimated 80–390 t of Cu still remains in the disposal area from the surface to a depth of 16 cm. Metal partitioning showed that 56–95% of the Cu is bound in the potential bioavailable fractions (exchangeable, reducible and oxidisable) of the sediments, totalling approximately 70–340 t, with potential for continuous release to the pore water and re-precipitation in over- and underlying sediments. Surface sediments in the deposit area were affected by elevated Cu concentrations just above the probable effect level according to the Norwegian sediment quality criteria, with 50–80% Cu bound in the exchangeable, reducible and oxidisable fractions, potentially available for release to the water column and/or for uptake in benthic organisms.