Screening 31 endocrine-disrupting pesticides in water and surface sediment samples from Beijing Guanting reservoir

For screening 31 potential or suspected endocrine-disrupting pesticides in water and surface sediments, a multiresidue analysis method based on gas chromatography with electron capture detection (GC/ECD) was developed. Solid phase extraction (SPE) technology with Oasis^® HLB cartridge was also applied in sample extraction. The relevant mean recoveries were 70–103% and 71–103% for water and sediment, respectively. Relative standard deviations (RSD) are 2.0–7.0%, 4.0–8.0% for water and sediment, respectively. Thirty one pesticides (-HCH, β-HCH, γ-HCH, δ-HCH, hexachlorobenzene (HCB), aldrin, heptachlor, endosulfan I & II, p,p′-DDD, o,p′-DDT, p,p′-DDT, p,p′-DDE, endrin aldehyde, endosulfan sulphate, methoxychlor, hepachlor epoxide, -chlordane, γ-chlordane, dieldrin, endrin, dicofol, acetochlor, alachlor, metolachlor, chlorpyriphos, nitrofen, trifluralin, cypermethrin, fenvalerate, deltamethrin) in water and surface sediment samples from Beijing Guanting reservoir were analyzed. Concentrations of pesticides ranged from 7.59 to 36.0 ng g⁻¹ on a dry wt. basis for sediment samples, from 279.3 to 2740 ng l⁻¹ for pore waters and from 48.8 to 890 ng l⁻¹ for water samples, respectively, with a mean concentration of 10.7 ng g⁻¹ in sediment, 735 ng l⁻¹ in pore water and 295 ng l⁻¹ in water, respectively. The data obtained provides information on the levels and sources of endocrine-disrupting pesticides in Guanting reservoir. These results underscore the need to improved environmental protection measures in order to reduce the exposure of the population and aquatic biota to these endocrine-disrupting compounds.     

Development of QSARs to investigate the bacterial toxicity and biotransformation potential of aromatic heterocylic compounds

A series of aromatic heterocyclic and hydrocarbon compounds were tested for toxicity and biotransformation potential against two contrasting lux-marked whole-cell microbial biosensors. Toxicity was determined by inhibition of light output of a Pseudomonas fluorescens construct that expresses lux constitutively. Biotransformation was tested by increase in light output of P. fluorescens HK44 (pUTK21), which expresses lux when in the presence of a metabolic intermediate (salicylate). The data were then modelled against physical/chemical properties of the compounds tested to see if quantitative structure–activity relationships (QSARs) could be derived. Toxicity was found to be accurately predicted by log K_ow (R²=0.95, Q²=0.88), with the basic (pyridine-ring containing) heterocycles modelled separately. The biotransformation data were best modelled using lowest unoccupied molecular orbital (LUMO) energies (R²=0.90, Q²=0.87).     

Organochlorine pesticides accumulation and degradation products in vegetation samples of a contaminated area in Galicia (NW Spain)

The content of 21 organochlorine pesticides were studied in vegetation samples of a highly contaminated area by isomers of hexachlorocyclohexane (HCH) located close to a former industrial area in Galicia (NW Spain). Five species of plants were collected at different points of the contaminated area and the different parts of the plants were separated in order to study differences in accumulation capabilities. Samples were extracted employing microwave energy followed by a clean-up step using solid phase extraction and finally determined by GC–ECD. The results obtained show that the most abundant pesticides are HCHs isomers, being the main isomers β-HCH and -HCH in all samples whereas δ-HCH and γ-HCH were at lower levels. Some other pesticides such as p,p′-DDT, p,p′-DDD and p,p′-DDE were also present in much lower amount in some of the samples. Several degradation products of HCH were also identified in some samples by GC–MS.     

Comparisons of coarse and fine versions of two carbons for reducing the bioavailabilities of sediment-bound hydrophobic organic contaminants

Coarse (whole) and finely ground Ambersorb 1500 and coarse and fine coconut charcoal were compared as to their efficiencies in scavenging organic contaminants desorbed from sediment. Aqueous slurries of a test sediment spiked (1 ppm) with p,p^′-DDE (DDE), 2,2^′,5,5^′-tetrachlorobiphenyl (TCB), naphthalene (NAP), or phenanthrene (PHEN), and containing 1% levels of the test carbons were treated by shaking at 35 °C while exposed to clusters of low-density polyethylene membrane (detox spiders). Controls consisted of spiked sediments and detox spiders but no added carbon of any kind and thus represented unimpeded bioavailabilities (to the spiders). After the treatments––agitation periods from 2.5 to 60 h, depending on contaminant hydrophobicity––the exposed detox spiders were analyzed. The fine carbon of either type was more effective than its coarser variant in obstructing contaminant bioavailabilities. The finer variants of both carbons obstructed the bioavailabilities of NAP and PHEN equally well as did the coarser variants of both. Whole Ambersorb 1500 and coarse coconut charcoal were similarly ineffective in intercepting TCB and DDE. Ground Ambersorb 1500 obstructed virtually all bioavailability of all four contaminants and was far more effective than fine coconut charcoal in intercepting DDE and TCB. An additional experiment compared the effectiveness of ground Ambersorb 1500 and fine coconut charcoal in obstructing the bioavailabilities from sediment of a broad array of spiked organochlorine pesticides. The performance of ground Ambersorb 1500 was again found to be superior; the bioavailable levels of each of the 27 pesticides were markedly lower in the presence of ground Ambersorb 1500 than in the presence of fine coconut charcoal.     

The enhancement of photodegradation efficiency using Pt-TiO2 catalyst

The residues from the extraction of lead/zinc (Pb/Zn) ores of most Pb/Zn mines are permanently stored in tailings ponds, which require revegetation to reduce their environmental impact. This can only be done if the main constraints on plant establishment are evaluated. This can readily be done by field and greenhouse studies.

To test this, the properties of different tailings from Lechang Pb/Zn mine located at the north of Guangdong Province in southern China have been studied. Physical and chemical properties including concentrations of metals (Pb, Zn, Cd and Cu) in the tailings and soils collected from different sites have been measured. The results showed that tailings contain low nitrogen (0.016–0.075%), low-organic matter (0.58–1.78%), high salt (3.55–13.85 dS/m), and high total and diethylene–tetramine–pentaacetic acid (DTPA)-extractable metal concentrations (total: 1019–1642 μg g⁻¹ Pb, 3078–6773 μg g⁻¹ Zn, 8–23 μg g⁻¹ Cd, and 85–192 μg g⁻¹ Cu; DTPA-extractable: 59–178 μg g⁻¹ Pb, 21–200 μg g⁻¹ Zn, 0.30–1.5 μg g⁻¹ Cd, and 4.3–12 μg g⁻¹ Cu). Aqueous extracts of tailings/soils (10%, 20% and 30%, w/v) from different sites were prepared for testing their effects on seed germination and root elongation of a vegetable crop Brassica chinensis and a grass species Cynodon dactylon. It was found that root elongation provided a better evaluation of toxicity than seed germination. The ranking of toxicity using root elongation was: high-sulfur tailings>tailingdam>sparsely vegetated tailings>densely vegetated tailings>mountain soil for both plants. This order was consistent with DTPA-extractable Pb contents in the tailings and soils. B. chinensis seedlings were then grown in the mixtures of different proportions of tailings and farm soil for 4 weeks, and the results (dry weights of seedlings) were in line with the root elongation test. All these demonstrated that heavy metal toxicity, especially available Pb, low content of nutrient, and poor physical structure were major constraints on plant establishment and colonization on the Pb/Zn mine tailings.     

Organochlorinated pesticides in sediments from the Lake Albufera of Valencia (Spain)

Bottom sediment samples from 121 sites of the Lake Albufera of Valencia were analyzed. Dieldrin, endrin, heptachlor and op′-DDT were not detected (<0.01 ng g⁻¹) in 88–93% of the sites. Aldrin and HCB concentration ranges were between <0.01 and 0.1 ng g⁻¹ in 86% and 94% of the sites, respectively. Heptachlor-epoxide and lindane 95% confidence intervals were 0.2–0.5 and 0.06–0.12, respectively. The greatest average concentration corresponds to pp′-DDE, pp′-DDD and pp′-DDT. The sum of six isomers and derivatives of the DDT average concentration reaches 2.1 ng g⁻¹, as opposed to 2.7 ng g⁻¹ for the sum of 13 pesticides considered. In the site with a major contamination, 27.0 ng g⁻¹ of pp′-DDD and 12.8 ng g⁻¹ of pp′-DDT were accumulated. The DDE:DDT proportion average was 0.37, indicating an aged DDT contamination. Concentrations of pesticides in sediments were compared to three sediment quality guidelines, and indicated that a low biological effects level can be expected in either sediments or aquatic organisms.     

Impacts of some meteorological parameters on SO2 and TSP concentrations in Erzurum, Turkey

The air pollution is the one of the most important environmental problems in Erzurum, situated in the eastern of Turkey, during winter periods. The unfavorable climate as well as the city’s topography, and inappropriate urbanization cause serious air pollution problems. The air pollutant concentrations in a city have a close relationship with its meteorological parameters. In the present study, the relationship between daily average total suspended particulate (TSP) and sulphur dioxide (SO₂) concentrations with meteorological factors, such as wind speed, temperature, relative humidity, pressure and precipitation, in 1995–2002 winter seasons was statistically analyzed using the stepwise multiple linear regression analysis. According to the results obtained through analysis, higher TSP and SO₂ concentrations are strongly related to colder temperatures, lower wind speed, higher pressure system and weakly lower precipitation and higher relative humidity. The statistical models of SO₂ and TSP including meteorological parameters gave R² of 0.74 and 0.88, respectively. Furthermore, the correlation between the previous day’s SO₂, TSP concentrations and actual concentrations of these pollutants on that day was investigated and found as 0.84 and 0.53, respectively. In order to develop this model, previous day’s SO₂ and TSP concentrations were added to the equations. The new model for SO₂ enhanced considerably (R² = 0.92), but for TSP new model was not enhanced (R² = 0.89).     

Impacts of simulated acid rain on cation leaching from the Latosol in south China

Acid rain is a problem of increasing agricultural, environmental, and ecological concerns worldwide. This study investigated impacts of simulated acid rain (SAR) on cation leaching from the Latosol in south China. Latosol is an acidic red soil and occurs in the tropical rainforest biome. Laboratory experiments were performed by leaching the soil columns with the SAR at a pH range from 2.5 to 7.0 over a 21-day period. A linear increase in effluent K⁺ concentration was found at the SAR pH 3.0, whereas an exponential decrease in effluent Na⁺ concentration was observed at all levels of the SAR pH. In general, leaching of Ca²⁺ and Mg²⁺ from the Latosol increased as the SAR pH decreased. There was a very good nonlinear correlation between the removal of soil K⁺ and the SAR pH (R² = 0.91), a good nonlinear correlation between the removal of soil Mg⁺² and the SAR pH (R² = 0.83), a fairly good nonlinear correlation between the removal of soil Ca⁺² and the SAR pH (R² = 0.56), and no correlation between the removal of soil Na⁺ and the SAR pH (R² = 0.06). Our study further revealed that the removal of soil cations such as K⁺, Ca⁺², and Mg⁺² can be quantified by the quadratic polynomial equations. In addition, impacts of the SAR on cation leaching depended not only on the SAR pH but also on the original soil pH.     

An investigation of adsorption at the air-water and soil-water interfaces for non-micellizing ethylene oxide-propylene oxide surfactants

Adsorption at the air–water interface and soil sorption from aqueous solution have been investigated for a group of ethylene oxide (EO)–propylene oxide (PO) block copolymeric surfactants. The group which have a common structural formula of EO_m PO_n EO_m is distinguished by the fact that they have large critical micelle concentration (CMC) values and therefore do not readily form micelles at common environmental concentrations and temperatures. Adsorption at the air–water interface is readily shown to be driven by the size of the hydrophobic PO block. The size of the reduction in surface tension produced by a common concentration of 10⁻⁵ mol dm⁻³ linearly increases with the size of the PO block as does the efficiency of adsorption at the air–water interface as measured by pC₂₀ – the negative logarithm of the surfactant concentration that produces a reduction in surface tension of 20 mN m⁻¹. Soil sorption data have also been captured for these compounds and the data are readily fitted to the Freundlich adsorption isotherm. However soil sorption is shown to be inversely related to the molecular mass of the molecules and appears to be related to the size of the hydrophilic EO blocks in the molecule.     

Kinetic studies of adsorption of thiocyanate onto ZnCl2 activated carbon from coir pith, an agricultural solid waste

The adsorption of thiocyanate onto ZnCl₂ activated carbon developed from coir pith was investigated to assess the possible use of this adsorbent. The influence of various parameters such as agitation time, thiocyanate concentration, adsorbent dose, pH and temperature has been studied. Adsorption followed second-order rate kinetics. Two theoretical adsorption isotherms, namely, Langmuir and Freundlich were used to describe the experimental results. The Langmuir adsorption capacity (Q₀) was found to be 16.2 mg g⁻¹ of the adsorbent. The per cent adsorption was maximum in the pH range 3.0–7.0. pH effect and desorption studies showed that ion exchange and chemisorption mechanism are involved in the adsorption process. Thermodynamic parameters such as ΔG⁰, ΔH⁰ and ΔS⁰ for the adsorption were evaluated. The negative values of ΔH⁰ confirm the exothermic nature of adsorption. Effects of foreign ions on the adsorption of thiocyanate have been investigated. Removal of thiocyanate from ground water was also tested.     

Characterizing As(III,V) adsorption by soils surrounding ash disposal facilities

Leachate derived from unlined coal ash disposal facilities is a potential anthropogenic source of arsenic to the environment. To establish a theoretical framework for predicting attenuation of arsenic by soils subject to ash landfill leachate, which is typically enriched in calcium and sulfate, the adsorption of As(V) and As(III) was characterized from 1 mM CaSO₄ for 18 soils obtained down-gradient from three ash landfill sites and representing a wide range in soil properties. As(V) consistently exhibited an order of magnitude greater adsorption than As(III). As(V) adsorption was best described by coupling pH with 15 s DCB-Fe (R² = 0.851,  = 0.001), although pH coupled to clay, DCB-Fe, or DCB-Al also generated strong correlations. For As(III), pH coupled to Ox–Fe (R² = 0.725,  = 0.001) or Ox–Fe/Al (R² = 0.771,  = 0.001) provided the best predictive relationships. Ca²⁺ induced increases in As(V) adsorption whereas sulfate suppressed both As(V) and As(III) adsorption. Attenuation of arsenic from ash leachate agreed well with adsorption measured from 1 mM CaSO₄ suggesting that the use of 1 mM CaSO₄ in laboratory adsorption tests is a reasonable approach for estimating arsenic behavior in soils surrounding ash landfills. We also showed that the impact of leachate-induced changes in soil pH over time may not be significant for As(V) adsorption at pH < 7; however, As(III) adsorption may be impacted over a wider pH range especially if phyllosilicate clays contribute significantly to adsorption. The benefits and limitations of predicting arsenic mobility using linearized adsorption coefficients estimated from nonlinear adsorption isotherms or from the relationships generated in this study are also discussed.     

The toxicity of copper,cadmium and zinc to four different Hydra (Cnidaria: Hydrozoa)

An acute toxicity study of three metals to Hydra species carried out using two different assessment methods, (i) determination of the LC50 and (ii) measurement of progressive morphological changes, demonstrated that relative toxicity decreased from copper to cadmium with zinc the least toxic for all species. The latter method revealed more details of the effect on Hydra in terms of physical damage to the polyp but both methods indicated that H. viridissima was more sensitive to copper and cadmium than H. vulgaris¹ (Zurich strain, male clone), H. vulgaris² (a dioecious strain reproducing sexually and asexually) and H. oligactis (dioecious, reproducing sexually and asexually). The responses to zinc were similar for all Hydra. The possible role of metabolic interactions between H. viridissima and its symbiotic green algae in contributing to the greater sensitivity of this polyp is discussed.     

Distribution of pesticides and heavy metals in trophic chain

Determination of triazines herbicides (atrazine and simazine) by high performance liquid chromatography (HPLC) in samples of trophic chain were worked out. Determination limits of 0.5 μg g⁻¹ for atrazine, 0.8 μg g⁻¹ for simazine with pesticides recovery of 70–77% in trophic chain samples were obtained. The content of simazine in soils was in range 1.72–57.89 μg g⁻¹, in grass 5–88 μg g⁻¹, in milk 2.32–15.29 μg g⁻¹, in cereals 10.98–387 μg g⁻¹, in eggs 30.14–59.48 μg g⁻¹, for fruits: 2.45–6.19 μg g⁻¹. The content of atrazine in soils was in range 0.69–19.59 μg g⁻¹, in grass 7.85–23.85 μg g⁻¹, in cereals 1.88–43.08 μg g⁻¹. Cadmium, lead and zinc were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES) in the same samples as atrazine and simazine. Determination limits for cadmium 5 × 10⁻³ μg g⁻¹, for lead 1 × 10⁻² μg g⁻¹, and for zinc 0.2 × 10⁻³ μg g⁻¹, were obtained. The content of cadmium in soil was in range 0.13–5.89 μg g⁻¹, in grass 114–627.72 × 10⁻³ μg g⁻¹, in milk 8.88–61.88 × 10⁻³ μg g⁻¹, in cereals 0.20–0.31 μg g⁻¹, in eggs 0.11–0.15 μg g⁻¹, in fruits 0.23–0.59 μg g⁻¹. The content of lead in soils was in range 0.57–151.50 μg g⁻¹, in grass 0.16–136.57 μg g⁻¹, in milk 1.16–3.74 μg g⁻¹, in cereals 1.05–5.47 μg g⁻¹, in eggs 5.79–55.87 μg g⁻¹, in fruits 21.00–87.36 μg g⁻¹. Zinc content in soil was in range 9.15–424.5 μg g⁻¹, in grass 35.20–55.87 μg g⁻¹, in milk 20.00–34.38 μg g⁻¹, in cereals 14.94–28.78 μg g⁻¹, in eggs 15.67–32.01 μg g⁻¹, in fruits 14.94–18.88 μg g⁻¹.

Described below extraction and mineralization methods for particular trophic chains allowed to determine of atrazine, simazine, cadmium, lead and zinc with good repeatability and precision. Emphasis was focused on liquid–liquid extraction and solid-phase extraction of atrazine and simazine from analysed materials, as well as, on monitoring the content of herbicides and metals in soil and along trophic chain. Higher concentration of pesticides in samples from west region of Poland in comparison to that of east region is likely related to common applying them in Western Europe in relation to East Europe. The content of metals strongly depends on samples origin (industry area, vicinity of motorways).     

Biosorption of cadmium by Myriophyllum spicatum L. and Myriophyllum triphyllum orchard

The aim of this study was to characterize the biological treatment of heavy metal-contaminated water employing Myriophyllum species, namely M. spicatum L. and M. triphyllum. Both species were found to be capable of removing cadmium (Cd) from water; the latter significantly outperformed. Myriophyllum species were treated with 0, 2, 4, 6, 8, 16 mg l⁻¹ cadmium solutions for 24, 48, 72, 96 h, respectively. Cd uptake of both species was the lowest at 2 mg l⁻¹ and the highest at 16 mg l⁻¹. Concentration related cadmium stress on both species exhibit significant difference on pigment levels (8–16 mg l⁻¹). These findings contribute to the fact that submerged aquatic plants can be used for the removal of heavy metals.     

Cold season CH4, CO2 and N2O fluxes from freshwater marshes in northeast China

Cold season (winter and thaw) CH₄, CO₂ and N₂O fluxes from freshwater marshes (47°35′N, 133°31′E, Northeast China) were measured, using the static chamber method. The mean CH₄ and CO₂ fluxes from Carex lasiocarpa (Cl) were 0.5 ± 0.19 and 6.23 ± 1.36 mg C m⁻² h⁻¹, respectively, and those from Deyeuxia angustifoli (Da) were 0.18 ± 0.15 and 5.22 ± 2.48 mg C m⁻² h⁻¹, respectively in winter. There was no significant difference between Cl and Da (p > 0.05). The contributions of winter CH₄ fluxes were about 5.5% and 3% in the Cl and Da, respectively. Marshes are an important potential N₂O sink in winter season in northeast China. During thaw, the CH₄ and CO₂ emissions rapidly increased, 4.5–6 times of winter emissions. Wetland became a source of N₂O. Cold season gases flux from northern wetlands play an important role in the seasonal gas exchange.     

Climate simulations using the GCRC 2-D zonally averaged statistical dynamical climate model

The two-dimensional statistical dynamical climate model, recently developed at the Global Change Research Center (GCRC 2D climate model) is presented and discussed. The model solves the 2-D primitive equations in finite difference form (mass continuity, Newton's second law, and the first law of thermodynamics) for the prognostic variables zonal mean density, zonal mean zonal velocity, zonal mean meridional velocity, and zonal mean temperature on a grid that has 18 nodes in latitude and 9 vertical nodes (plus the surface). The equation of state, p = ρRT and an assumed hydrostatic atmosphere, δp = −ρgδz, are used to diagnostically calculate the zonal mean pressure and vertical velocity for each grid node, and the moisture balance equation is used to estimate the precipitation rate.

The performance of the model at simulating the two-dimensional temperature, zonal winds, and mass stream function is discussed here. The strengths and weaknesses of the model are highlighted and plans for future model experiments and improvements are given. The parameterization of the transient eddy fluxes of heat and momentum developed by Stone and Yao (1987 and 1990) are used with small modifications. These modifications are shown to improve the performance of the model at simulating the observed climate system as well as increase the model's computational stability.     

Runoff rates,chemical speciation and bioavailability of copper released from naturally patinated copper

The release of copper, induced by atmospheric corrosion, from naturally patinated copper of varying age (0 and 30 years) has been investigated together with its potential ecotoxic effect. Results were generated in an interdisciplinary research effort in which corrosion science and ecotoxicology aspects were combined. The aim of the investigation was to elucidate the situation when copper-containing rainwater leaves a roof in terms of runoff rate, chemical speciation, bioavailability and ecotoxicity effects. Data have been collected during a three-year field exposure conducted in the urban environment of Stockholm, Sweden. The potential environmental effects have been evaluated using a combination of a copper specific biosensor test with the bacterium Alcaligenes eutrophus and the conventional 72-h growth inhibition test with the green alga Raphidocelis subcapitata. The results show annual runoff rates between 1.0 and 1.5 g/m2 year for naturally patinated copper of varying age. The runoff rate increased slightly with patina age, which mainly is attributed to the enhanced first flush effect observed on thicker patina layers. The total copper concentration in investigated runoff samplings ranged from 0.9 to 9.7 mg/l. Both computer modeling and experimental studies revealed that the majority (60-100%) of released copper was present as the free hydrated cupric ion, Cu(H2O)6(2+), the most bioavailable copper species. However, other copper species in the runoff water, such as, e.g. Cu(OH)+ and Cu2(OH)2(2+), were also bioavailable. The copper-containing runoff water, sampled directly after release from the roof, caused significant reduction in growth rate of the green alga. It should be emphasized that the results describe the runoff situation immediately after release from the copper roof and not the real environmental ecotoxicity. Therefore the data should only be used as an initial assessment of the potential environmental effect of copper runoff from building applications. Future risk assessments should also consider dilution effects of copper, changes in its chemical speciation and bioavailability during environmental entry, and type and sensitivity of the receiving ecosystem.     

Effect of some heavy metals and soil humic substances on the phytochelatin production in wild plants from silver mine areas of Guanajuato, Mexico

Phytochelatins (PCs) were determined in the wild plants, focusing on their relationship with the levels of heavy metals and humic substances (HS) in soil. Ricinus communis and Tithonia diversifolia were collected from several sites in Guanajuato city (Mexico), which had long been the silver and gold mining center. The analysis of PCs in root extracts was carried out by liquid chromatography (derivatization with monobromobimane). Total Ag, Cd, Cu and Pb in plant roots and in soil samples, as well as soil HS were determined. The association of metals with HS in soils was evaluated by size exclusion chromatography (SEC) with UV and ICP-MS detection. The results obtained revealed the induction of PCs in R. communis but not in T. diversifolia. The levels of Cd and Pb in plant roots presented strong positive correlation with PC-2 (r = 0.9395, p = 0.005; r = 0.9573, p = 0.003, respectively), indicating that these two metals promote PCs induction in R. communis. On the other hand, the inverse correlation was found between soil HS and metal levels in roots of R. communis (Cu > Pb > Cd > Ag), in agreement with the decreasing affinity of these metals to HS. Importantly, the inverse correlation between soil HS and plant PC-2 was observed (r = −0.7825, p = 0.066). These results suggest that metals strongly bound to HS could be less bioavailable to plants, which in turn would limit their role in the induction of PCs. Indeed, the SEC elution profiles showed Pb but not Cd association with HS and the correlation between metal in soil and PC-2 in plant was statistically significant only for Cd (r = 0.7857, p = 0.064). Based on these results it is proposed that the role of heavy metals in PCs induction would depend on their uptake by R. communis, which apparently is controlled by the association of metals with soil HS. This work provides further evidence on the role of environmental conditions in the accumulation of heavy metals and phytochelatin production in plants.     

Study on the fluorescence characteristics of bromadiolone in aqueous and organized media and application in analysis

The fluorescence spectroscopic behavior of bromadiolone (anticoagulant rodenticide), a substituted 4-hydroxycoumarin derivative, was investigated in water and in organized media like micelles and cyclodextrins. A detailed study on various photophysical parameters like fluorescence intensity (I_F), quantum yield (), lifetime (τ) and steady state fluorescence anisotropy (r) of bromadiolone in aqueous and in organized media was carried out. Bromadiolone in aqueous solution was observed to be in an aggregated state, thereby showing weak emission due to self-quenching. Marked enhancement of fluorescence intensity was observed in organized media like micelles and β-cyclodextrin. A preliminary investigation has been done to find out whether this enhancement of fluorescence can be used to develop a sensitive analytical method for determination of bromadialone in aqueous media. A linear relationship between the fluorescence intensity and concentration of bromadiolone was observed in the range of 0.15–7.9 μg ml⁻¹ in cetyltrimethylammonium bromide (CTAB) and 0.5–26.4 μg ml⁻¹ in β-cyclodextrin medium. The lower detection limit was found to be 37 ng ml⁻¹ in presence of CTAB and 23 ng ml⁻¹ in β-cyclodextrin. Comparison with 4-hydroxycoumarin, an unsubstituted analogue, was made.     

Copper complexation by tannic acid in aqueous solution

The speciation of titrated copper in a dissolved tannic acid (TA) solution with an initial concentration of 4 mmol organic carbon (OC)/l was investigated in a nine-step titration experiment (Cu/OC molar ratio = 0.0030–0.0567). We differentiated between soluble and insoluble Cu species by 0.45 μm filtration. Measurements with a copper ion selective electrode (ISE) and diffusive gradients in thin films (DGT) were conducted to quantify unbound Cu(II) cations (‘free’ Cu) and labile soluble Cu complexes. For the DGT measurements, we used an APA hydrogel and a Chelex 100 chelating resin (Na form). Insoluble organic Cu complexes (>0.45 μm) was the dominant Cu species for Cu/OC = 0.0030–0.0567 with a maximum fraction of 0.96 of total Cu. At Cu/OC > 0.0100, Cu-catalysed degradation of aggregate structures resulted in a strong increase of free Cu and (labile) soluble Cu complexes with a maximum fraction of 0.28 and 0.32 of total Cu, respectively. Labile (i.e. DGT-detectable) soluble Cu complexes had a relatively high averaged diffusion coefficient (D) in the APA hydrogel (3.50 × 10⁻⁶– 5.58 × 10⁻⁶ cm² s⁻¹).