Screening 31 endocrine-disrupting pesticides in water and surface sediment samples from Beijing Guanting reservoir

For screening 31 potential or suspected endocrine-disrupting pesticides in water and surface sediments, a multiresidue analysis method based on gas chromatography with electron capture detection (GC/ECD) was developed. Solid phase extraction (SPE) technology with Oasis^® HLB cartridge was also applied in sample extraction. The relevant mean recoveries were 70–103% and 71–103% for water and sediment, respectively. Relative standard deviations (RSD) are 2.0–7.0%, 4.0–8.0% for water and sediment, respectively. Thirty one pesticides (-HCH, β-HCH, γ-HCH, δ-HCH, hexachlorobenzene (HCB), aldrin, heptachlor, endosulfan I & II, p,p′-DDD, o,p′-DDT, p,p′-DDT, p,p′-DDE, endrin aldehyde, endosulfan sulphate, methoxychlor, hepachlor epoxide, -chlordane, γ-chlordane, dieldrin, endrin, dicofol, acetochlor, alachlor, metolachlor, chlorpyriphos, nitrofen, trifluralin, cypermethrin, fenvalerate, deltamethrin) in water and surface sediment samples from Beijing Guanting reservoir were analyzed. Concentrations of pesticides ranged from 7.59 to 36.0 ng g⁻¹ on a dry wt. basis for sediment samples, from 279.3 to 2740 ng l⁻¹ for pore waters and from 48.8 to 890 ng l⁻¹ for water samples, respectively, with a mean concentration of 10.7 ng g⁻¹ in sediment, 735 ng l⁻¹ in pore water and 295 ng l⁻¹ in water, respectively. The data obtained provides information on the levels and sources of endocrine-disrupting pesticides in Guanting reservoir. These results underscore the need to improved environmental protection measures in order to reduce the exposure of the population and aquatic biota to these endocrine-disrupting compounds.     

Organochlorinated pesticides in sediments from the Lake Albufera of Valencia (Spain)

Bottom sediment samples from 121 sites of the Lake Albufera of Valencia were analyzed. Dieldrin, endrin, heptachlor and op′-DDT were not detected (<0.01 ng g⁻¹) in 88–93% of the sites. Aldrin and HCB concentration ranges were between <0.01 and 0.1 ng g⁻¹ in 86% and 94% of the sites, respectively. Heptachlor-epoxide and lindane 95% confidence intervals were 0.2–0.5 and 0.06–0.12, respectively. The greatest average concentration corresponds to pp′-DDE, pp′-DDD and pp′-DDT. The sum of six isomers and derivatives of the DDT average concentration reaches 2.1 ng g⁻¹, as opposed to 2.7 ng g⁻¹ for the sum of 13 pesticides considered. In the site with a major contamination, 27.0 ng g⁻¹ of pp′-DDD and 12.8 ng g⁻¹ of pp′-DDT were accumulated. The DDE:DDT proportion average was 0.37, indicating an aged DDT contamination. Concentrations of pesticides in sediments were compared to three sediment quality guidelines, and indicated that a low biological effects level can be expected in either sediments or aquatic organisms.     

Organochlorine pesticides accumulation and degradation products in vegetation samples of a contaminated area in Galicia (NW Spain)

The content of 21 organochlorine pesticides were studied in vegetation samples of a highly contaminated area by isomers of hexachlorocyclohexane (HCH) located close to a former industrial area in Galicia (NW Spain). Five species of plants were collected at different points of the contaminated area and the different parts of the plants were separated in order to study differences in accumulation capabilities. Samples were extracted employing microwave energy followed by a clean-up step using solid phase extraction and finally determined by GC–ECD. The results obtained show that the most abundant pesticides are HCHs isomers, being the main isomers β-HCH and -HCH in all samples whereas δ-HCH and γ-HCH were at lower levels. Some other pesticides such as p,p′-DDT, p,p′-DDD and p,p′-DDE were also present in much lower amount in some of the samples. Several degradation products of HCH were also identified in some samples by GC–MS.     

Mechanochemical removal of organo-chlorinated compounds by inorganic components of soil

The purpose of this work is to evaluate the catalytic efficiency of two metal oxides, ferrihydrite and birnessite and of a ferruginous smectite, towards organic molecules such as 4-chloroaniline (4-CA), pentachlorophenol (PCP), and five polychlorinated biphenyls (PCBs) characterised by different number and position of chlorine atoms. Mechanochemical dry contacts with light grinding between catalytic surfaces and pollutants have been carried out.

The efficiency of the mechanochemical removal was compared with batch experiments for the soluble compounds (PCP and 4-CA). The removal of 4-CA and PCP by the mechanochemical procedure resulted more effective than by batch contact in the presence of birnessite and ferrihydrite, particularly at higher pH (100% removal of 4-CA by birnessite in 30 min at pH 8.6 after the mechanochemical contact compared to 20% removal using the batch interaction at the same pH).

The mechanochemical contact of PCBs and birnessite produced a removal of pollutant that was a function of the number of chlorine atoms (complete removal of 2,2^′-dichlorobiphenyl in 10 days and a removal of 30% and 20% of 2^′,3,4-trichlorobiphenyl and 3,3^′,4,4^′-tetrachlorobiphenyl, respectively in 90 days) and of the position of chlorine atoms about the biphenyl rings (100% of 2,2^′-dichlorobiphenyl in 10 days, 84% of 3,3^′-dichlorobiphenyl in 15 days and 40% of 4,4^′-dichlorobiphenyl in 27 days).     

Analysis of Ah receptor pathway activation by brominated flame retardants

Brominated flame-retardants (BFRs) are used as additives in plastics to decrease the rate of combustion of these materials, leading to greater consumer safety. As the use of plastics has increased, the production and use of flame-retardants has also grown. Many BFRs are persistent and have been detected in environmental samples, raising concerns about the biological/toxicological risk associated with their use. Most BFRs appear to be non-toxic, however there is still some concern that these compounds, or possible contaminants in BFRs mixtures could interact with cellular receptors. In this study we have examined the interaction of decabromodiphenyl ether, Firemaster BP4A (tetrabromobisphenol A), Firemaster PHT4 (tetrabromophthalic anhydride), hexabromobenzene, pentabromotoluene, decabromobiphenyl, Firemaster BP-6 (2,2^′,4,4^′,5,5^′-hexabromobiphenyl) and possible contaminants of BFR mixtures with the Ah receptor. Receptor binding and activation was examined using the Gel Retardation Assay and increased expression of dioxin responsive genes was detected using the reporter gene based CALUX assay. The results demonstrate the ability of BFRs to activate the AhR signal transduction pathway at moderate to high concentrations as assessed using both assays. AhR-dependent activation by BFRs may be due in part to contaminants present in commercial/technical mixtures. This was suggested by our comparative analysis of Firemaster BP-6 versus its primary component 2,2^′,4,4^′,5,5^′-hexabromobiphenyl. Some technical mixtures of brominated flame-retardants contain brominated biphenyls, dioxins or dibenzofurans as contaminants. When tested in the CALUX assay these compounds were found to be equivalent to, or more active than their chlorinated analogues. Relative effective potency values were determined from dose response curves for these brominated HAHs.     

Detoxification of hexachlorobenzene by dechlorination with potassium-sodium alloy

Dechlorination of hexachlorobenzene (HCB) was achieved by a liquid potassium–sodium (K–Na)-alloy. HCB in a cyclohexane/benzene solution (22 mmol/l, 4.67 g/l as chlorine) was dechlorinated by almost 100% after a 30-min reaction, indicating high reactivity of K–Na alloy and high proton donating power of cyclohexane. Decreasing orders of chlorobenzenes identified after a 15-min reaction, by amount were 1,2,3,4- > 1,2,3,5- > 1,2,4,5- for tetrachlorobenzenes, 1,2,4- > 1,2,3- > 1,3,5- for trichlorobenzenes, and 1,4- > 1,3- > 1,2- for dichlorobenzenes. It was hypothesized that once one chlorine atom in HCB was replaced with a proton, the adjacent chlorine atom to the proton tended to be replaced with another hydrogen atom. A total of 63 PCBs formed via the Wurtz–Fittig reaction were identified as by-products in the sample after a 15-min reaction. Among PCBs found, 2,3^′,4^′,5-tetrachlorobiphenyl, which was a product from 1,2,4-trichlorobenzene formed via the Wurtz–Fittig reaction, was detected in relatively high concentration (48.9 nmol/ml). The sample obtained from a reaction mixture after 30 min contained only 14 PCBs in trace amounts, indicating that the PCBs formed were also further dechlorinated by K–Na alloy. Non-chlorinated compounds––such as methylbenzene, dimethylbenzene, dimer of tetrahydrofuran, and dicyclohexyl (dimer of cyclohexane)––were also identified in the samples. A method using K–Na alloy developed in the present study dechlorinated satisfactorily HCB at room temperature.     

Trace metals and organochlorines in sediments near a major ocean outfall on a high energy continental margin (Sydney, Australia)

Sewage effluent from a large ocean outfall south of Sydney, southeastern Australia, is efficiently dispersed on this high energy continental margin. An enrichment of Ag, Cu, Pb and Zn is only detectable in the fine fraction (<62.5 microm) of sediment. Ag, Co, Cu, Ni, Pb and Zn in the bulk sample correlate strongly with the mud content of surficial sediment, making an identification of the anthropogenic trace metal source difficult using total sediment analyses. The concentrations of HCB and DDE in the total sediment are also slightly elevated near the outfall. In the vicinity of the outfall, the estimated sewage component in the fine fraction of sediment, using Ag, Cu and Zn in a conservative, two-endmember physical mixing model, is <5% and is <0.25% of the total sediment. A greater anthropogenic Pb component in the fine fraction (mean: 24.8%) of surficial sediment compared to Ag, Cu and Zn may suggest a source other than sewage to Sydney continental margin sediments.     

Peroxidative degradation of selected PCB: a mechanistic study

The enzyme-induced decomposition and biodegradation of PCB were investigated. 2,5-Dichlorobiphenyl (PCB 9) and 2,2^′,5,5^′-tetrachlorobiphenyl (PCB 52) were used as example compounds to study efficiency and mechanism of the degradation processes. It was found that the application of horseradish peroxidase (HRP) together with defined amounts of hydrogen peroxide removed 90% of the initial concentration of PCB 9 and 55% of the initial concentration of PCB 52 from an aqueous solution after a reaction period of 220 min. Dechlorination was observed as the initial step. Although the metabolites identified were mainly chlorinated hydroxybiphenyls, benzoic acids and non-substituted 1,1^′-biphenyl, some higher chlorinated biphenyl isomers also appeared. The biodegradation of PCB 9 using the white rot fungus Trametes multicolor took about four weeks and reduction was about 80% of the initial concentration. The metabolites produced (dichlorobenzenes, chlorophenols and alkylated benzenes) were not quite the same as those observed upon incubation with HRP.     

Studies on polycyclic aromatic hydrocarbons in two sediment cores from the huaxi reservoir,china: Assessment of levels,sources, and ecological risk

This study investigated the levels, sources and ecological risks of 16 polycyclic aromatic hydrocarbons (PAHs) in two sediment cores that were collected along the Huaxi Reservoir. The spatial distributions and residue levels of the 16 priority PAHs in the sediments from the Huaxi Reservoir were analyzed for their potential ecological risk, source apportionment and contribution to the total PAH residue. The concentration level of the total PAHs (TPAHs) was in the range 1805 ng·g^?1 to 20023 ng·g^?1 based on dry weight, and the content of PAHs in the Huaxi Reservoir exhibited a gradual upward trend. The PAH congener ratios fluoranthene/(fluoranthene + pyrene) and indeno[1, 2, 3-cd]pyrene/(indeno[1, 2, 3-cd]pyrene + benzo[g, h, i]perylene) were used to identify the source. The main source of the low molecular weight PAHs was wood and coal combustion, whereas the high molecular weight PAHs were primarily from petroleum combustion sources. The results of an ecological risk assessment demonstrated that ACE poses a potential ecological risk, while FLU, NAP, ANT, BaP, DBA, PHEN and PYR can have serious ecological risks.     

Resistant sorption of in situ chlorobenzenes and a polychlorinated biphenyl in river Rhine suspended matter

The desorption kinetics of in situ chlorobenzenes (dichlorobenzenes, pentachlorobenzene and hexachlorobenzene) and 2,4,4^′-trichlorobiphenyl (PCB-28) were measured with a gas-purge technique for river Rhine suspended matter sampled in Lobith, The Netherlands. This suspended matter is the main source of sediment accumulation in lake Ketelmeer. In lake Ketelmeer sediment earlier observations showed that slow and very slow fractions dominate the desorption profile.

For the river Rhine suspended matter, only for PCB-28 a fast desorbing fraction of around 1.6% could be detected. The observed rate constants were on the average 0.2 h⁻¹ for fast desorption, 0.004 h⁻¹ for slow desorption, and 0.00022 h⁻¹ for very slow desorption. These values are in agreement with previous findings for the sediment from lake Ketelmeer and with available literature data on fast, slow, and very slow desorption kinetics.

The results from this study show the similarity of desorption profiles between river Rhine suspended matter, and the top layer sediment from lake Ketelmeer. This indicates that slow and very slow fractions are already present in material forming the top layer of lake Ketelmeer, and were not formed after deposition of this material in the lake. The absence of detectable fast fractions for most compounds could be caused by the absence of recent pollution of the suspended matter. But, the observations may also be explained by a rapid disappearance of compounds from the fast fraction due to a combination of a high affinity of very slow sites for these compounds, and their relatively high volatility.     

An investigation of adsorption at the air-water and soil-water interfaces for non-micellizing ethylene oxide-propylene oxide surfactants

Adsorption at the air–water interface and soil sorption from aqueous solution have been investigated for a group of ethylene oxide (EO)–propylene oxide (PO) block copolymeric surfactants. The group which have a common structural formula of EO_m PO_n EO_m is distinguished by the fact that they have large critical micelle concentration (CMC) values and therefore do not readily form micelles at common environmental concentrations and temperatures. Adsorption at the air–water interface is readily shown to be driven by the size of the hydrophobic PO block. The size of the reduction in surface tension produced by a common concentration of 10⁻⁵ mol dm⁻³ linearly increases with the size of the PO block as does the efficiency of adsorption at the air–water interface as measured by pC₂₀ – the negative logarithm of the surfactant concentration that produces a reduction in surface tension of 20 mN m⁻¹. Soil sorption data have also been captured for these compounds and the data are readily fitted to the Freundlich adsorption isotherm. However soil sorption is shown to be inversely related to the molecular mass of the molecules and appears to be related to the size of the hydrophilic EO blocks in the molecule.     

Development and calibration of a passive sampler for N-nitrosodimethylamine (NDMA) in water

N-Nitrosamines such as N-nitrosodimethylamine (NDMA) are organic compounds of environmental concern in groundwater, wastewater and potable water due to their potent carcinogenicity in laboratory animal studies and probable human carcinogenicity. While passive sampling techniques have become a widely used tool for providing time-averaged estimates of trace pollutant concentration, for chemicals such as NDMA that have relatively high water solubility, the selection of a suitable sorbent is difficult. This work is a proof of principle study that investigated for the first time the use of coconut charcoal as a passive sampler sorbent. Apparent charcoal/water sorption coefficients for NDMA were >551 mL g⁻¹ at environmentally relevant aqueous concentrations of less than 1 μg L⁻¹. Under the experimental conditions employed, a sampling rate of 0.45 L d⁻¹ was determined and for an aqueous concentration of 1000 ng L⁻¹, it is predicted that the sampler remains in the linear uptake stage for approximately 4 d, while equilibrium attainment would require about 26 d. The presence of humic acid, used as a surrogate for DOC, enhanced NDMA sorption on the coconut charcoal.     

Transepithelial transport and cellular accumulation of steroid hormones and polychlorobiphenyl in porcine kidney cells expressed with human P-glycoprotein

Endocrine disrupters such as sex hormone-like chemicals and the non-physiological ligands for aryl hydrocarbon receptor (AhR) exert many adverse biological effects. The ligands for AhR disturb gene expression downstream of the gene induced by estrogen receptor at a very low concentration. Thus, transepithelial transport and cellular accumulation of cortisol (COR) and estrogen as congeners of sex hormone-like chemicals, and 3,3^′,4,4^′-tetrachlorobiphenyl (TeCB) as one of the ligands for AhR were examined in a monolayer of porcine kidney cells transfected with human P-glycoprotein (LLC-COL). The net basal-to-apical transport of COR increased in LLC-COL compared to that in the wild type cells (LLC-PK1) the same as in vinblastine, whereas the net transport of estradiol (EST) was not detected in either cell group. Though the diffusion transports of EST for both directions, basal-to-apical and apical-to-basal, were higher than that of COR, cellular accumulation of EST was higher than that of COR. Transepithelial transport of TeCB was very low and the net basal-to-apical transport was not detected, while it was highly accumulated in the epithelial cells. The accumulation was slightly higher in LLC-COL than in LLC-PK1 at high dose.     

Assessment of pesticide contamination in three Mississippi Delta oxbow lakes using Hyalella azteca

Three oxbow lakes in northwestern Mississippi, USA, an area of intensive agriculture, were assessed for biological impairment from historic and current-use pesticide contamination using the amphipod, Hyalella azteca. Surface water and sediment samples from three sites in each lake were collected from Deep Hollow, Beasley, and Thighman Lakes from September 2000 to February 2001. Samples were analyzed for 17 historic and current-use pesticides and selected metabolites. Ten-day H. azteca survival and growth (as length and dry weight) were measured to determine the degree of biological impairment. Maximum number of detectable pesticides in surface water from Deep Hollow, Beasley and Thighman Lakes was 10, 11, and 17, respectively. Maximum number of detectable pesticides in lake sediments was 17, 17, and 15, respectively. Bioassay results indicated no observable survival effects on H. azteca exposed to surface water or sediment from any lake examined and no growth impairment in animals exposed to lake sediments. However, growth was significantly impaired in surface water exposures from Deep Hollow Lake (2 sites) and Beasley Lake (1 site). Statistically significant relationships between growth impairment (length) and cyanazine, methyl parathion, λ-cyhalothrin, chlorfenapyr, and pp′DDE surface water concentrations in Deep Hollow Lake as well as trifluralin, atrazine, and methyl parathion in Beasley Lake were observed. Although pesticide frequency and concentrations were typically greater in sediment than surface water, bioassay results indicated decreased availability of these pesticides in sediment due to the presence of clay and organic carbon. Growth impairment observed in surface water exposures was likely due to complex interaction of pesticide mixtures that were present.     

A simple effective procedure for the determination of adenosine triphosphate in soils

A simple method for the extraction and determination of adenosine 5′-triphosphate (ATP) in soil is described. ATP was extracted by stirring with dimethyl sulphoxide (DMSO), followed by adding 0.01 M trisodium phosphate (Na₃PO₄) buffer solution for a further dispersion. The ATP content was quantitatively measured by luciferin-luciferase system employing a standard addition technique. The method was most efficient in comparison with 7 other extraction procedures. The recoveries of ATP in spiked soil were found to be approximately 100 %. ATP contents in 16 selected soils were in ranges of 0.76±0.05 – 7.79±0.83 μg/g (dry weight). A significant correlation between ATP amounts and biomasses in these soils was also observed.     

Identification of a novel PCB source through analysis of 209 PCB congeners by US EPA modified method 1668

PCDD/Fs and PCBs in surface waters and effluent waste streams flowing into New York/New Jersey Harbor were sampled by large volume filtration and solid phase extraction (XAD-2). Passive hexane samplers were employed in sewer trackdown. Extraction media were analyzed for 2,3,7,8 substituted PCDD/Fs and all 209 PCB congeners. The non-Aroclor PCB congener, 3,3^′-DiCB, was ubiquitous in the harbor and was found to be associated with pigment manufacture. Knowledge of inadvertent synthesis of non-Aroclor PCBs is not new but its magnitude and the generation of congeners with dioxin-like properties from this process is novel.     

Enantiomer fractions of chiral organochlorine pesticides and polychlorinated biphenyls in standard and certified reference materials

Enantiomeric ratios (ERs) and enantiomeric fractions (EFs) of a number of chiral organochlorine pesticides and PCB atropisomers were measured by chiral gas chromatography/mass spectrometry (GC/MS) in five standard (SRM) and certified (CRM) reference materials: SRM 1588a (organics in cod liver oil), SRM 1945 (organics in whale blubber), Marine Mammal Quality Assurance Exercise Control Material IV (NIST IV, organics in whale blubber), CRM trout, and CRM EC-5 (sediment). Target analytes were cis- and trans-chlordane, heptachlor exo-epoxide, oxychlordane, U82, MC5, MC6, MC7, o,p^′-DDT, and PCB congeners 91, 95, 136, 149, 174, 176, and 183. Measured ERs and EFs are in close agreement with the few literature values reported for some of these analytes in SRMs and CRMs. Chiral PCB ERs and EFs measured by one-dimensional chiral GC/MS were similar to values measured using multidimensional chiral GC/MS. Non-racemic chiral compositions are in agreement with known uptake and biotransformation in the respective environmental matrices. These values should aid in the quality assurance/quality control methodologies for chiral environmental chemistry using standardized reference materials.     

Distribution and ecotoxicological concerns of persistent organic pollutants in sediment from creek ecosystem

In order to study the distribution and ecotoxicological concerns of persistent organic pollutants, grab sediment samples were collected from different locations across Thane creek, India. Analyses of samples were carried out using gas chromatography (GC)–electron capture detector and GC–mass spectrometry techniques. In organochlorine pesticides (OCPs), DDT (1,1,1,-trichloro-2,2-bis(p-chlorophenyl) ethane), DDE (1,1-dichloro-2,2-bis(p-chlorophenyl) ethylene), DDD (1-chloro-4-(2,2-dichloro-1-(4-chlorophenyl)ethyl) benzene) and α, β, and γ conformer of hexachlorocyclohexane (HCH), and 9 polychlorinated biphenyls (PCBs) congeners were analyzed in surface sediment samples. Concentrations of these pollutants in grab sediment samples may indicate their current use and impact on marine ecosystem. Average concentrations of total DDT (including DDD and DDE), HCH, and Σ₉PCBs were found to be 4.9, 12.5, and 2.9 µg kg^?1(dry weight) respectively. High concentrations of OCPs and PCBs were found at discharge locations in creek compared to other locations. Location-wise distribution of OCPs and PCBs indicates their high concentrations at the waste water receiving point. Data were compared for ecotoxicological impacts based on the levels specified in the sediment quality standards of the US Environmental Protection Agency and the Canadian Council of Ministers of the Environment. γ-HCH was found to have maximum potential to induce ecotoxicological impacts.     

Vapour pressures, aqueous solubility, Henry's law constants and air/water partition coefficients of 1,8-dichlorooctane and 1,8-dibromooctane

New data on the vapour pressures and aqueous solubility of 1,8-dichlorooctane and 1,8-dibromooctane are reported as a function of temperature between 20 °C and 80 °C and 1 °C and 40 °C, respectively. For the vapour pressures, a static method was used during the measurements which have an estimated uncertainty between 3% and 5%. The aqueous solubilities were determined using a dynamic saturation column method and the values are accurate to within ±10%. 1,8-Dichlorooctane is more volatile than 1,8-dibromooctane in the temperature range covered (p_sat varies from 3 to 250 Pa and from 0.53 to 62 Pa, respectively) and is also approximately three times more soluble in water (mole fraction solubilities at 25 °C of 5.95 × 10⁻⁷ and 1.92 × 10⁻⁷, respectively). A combination of the two sets of data allowed the calculation of the Henry’s law constants and the air water partition coefficients. A simple group contribution concept was used to rationalize the data obtained.     

A Preliminary Evaluation of the DDT Contamination of Sediments in Lakes Natron and Bogoria (Eastern Rift Valley,Africa)

Dichlorodiphenyltrichloroethane (DDT) is still used in Africa for the indoor control of malaria and it may represent a potential hazard for wildlife. The littoral sediments of two alkaline-saline lakes, Natron (Tanzania) and Bogoria (Kenya), in the Eastern Rift Valley, supporting large populations of lesser flamingos (Phoeniconaias minor), were analysed for DDT residues. Physical–chemical analyses (temperature, conductivity, pH and dissolved oxygen) were also performed on the water of the two lakes and in the tributaries of Lake Natron, to evaluate the influence of the environmental variables on pollutant occurrence. At Lake Natron, around 1 km from the sediment collection sites, tree leaves of Acacia tortilis were also collected. The main metabolite found in all sediment samples was pp’DDE, whilst equal concentrations of pp’DDT and pp’DDE were measured in acacia leaves. The levels of DDTs measured in the sediments were within 5.9–30.9 ng g⁻¹ d.w., reaching the maximum value in a tributary of Lake Natron. On the whole, the contamination of Lake Natron and Lake Bogoria basins seems to be quite moderate. Nevertheless, the pp’DDE/pp’DDT ratio equals 1 in the Acacia tortilis leaves, which makes one suppose that the input of the parent compound was rather recent and could have been from aerial transport or dust from relatively close-by old pesticides storage sites.