Improvement of oxygen-containing functional groups on olive stones activated carbon by ozone and nitric acid for heavy metals removal from aqueous phase

Recently, modification of surface structure of activated carbons in order to improve their adsorption performance toward especial pollutants has gained great interest. Oxygen-containing functional groups have been devoted as the main responsible for heavy metal binding on the activated carbon surface; their introduction or enhancement needs specific modification and impregnation methods. In the present work, olive stones activated carbon (COSAC) undergoes surface modifications in gaseous phase using ozone (O₃) and in liquid phase using nitric acid (HNO₃). The activated carbon samples were characterized using N₂ adsorption–desorption isotherm, SEM, pHpzc, FTIR, and Boehm titration. The activated carbon parent (COSAC) has a high surface area of 1194 m²/g and shows a predominantly microporous structure. Oxidation treatments with nitric acid and ozone show a decrease in both specific surface area and micropore volumes, whereas these acidic treatments have led to a fixation of high amount of surface oxygen functional groups, thus making the carbon surface more hydrophilic. Activated carbon samples were used as an adsorbent matrix for the removal of Co(II), Ni(II), and Cu(II) heavy metal ions from aqueous solutions. Adsorption isotherms were obtained at 30 °C, and the data are well fitted to the Redlich–Peterson and Langmuir equation. Results show that oxidized COSACs, especially COSAC(HNO₃), are capable to remove more Co(II), Cu(II), and Ni(II) from aqueous solution. Nitric acid-oxidized olive stones activated carbon was tested in its ability to remove metal ions from binary systems and results show an important maximum adsorbed amount as compared to single systems.     

The conversion of chicken manure to biooil by fast pyrolysis I. Analyses of chicken manure, biooils and char by 13C and 1H NMR and FTIR spectrophotometry

Fast pyrolysis of chicken manure produced two biooils (Fractions I and II) and a residual char. All four materials were analyzed by chemical methods, 13C and 1H Nuclear Magnetic Resonance Spectrometry (13C and 1H NMR), and Fourier Transform Infrared Spectrosphotometry (FTIR). The char showed the highest C content and the highest aromaticity. Of the two biooils Fraction II was higher in C, yield and calorific value but lower in N than Fraction I. The S and ash content of the two biooil fractions were low. The Cross Polarization Magic Angle Spinning (CP-MAS) 13C NMR spectrum of the initial chicken manure showed it to be rich in cellulose, which was a major component of sawdust used as bedding material. Nuclear Magnetic Resonance (NMR) spectra of the two biooils indicated that Fraction I was less aromatic than Fraction II. Among the aromatics in the two biooils, we were able to tentatively identify N-heterocyclics like indoles, pyridines, and pyrazines. FTIR spectra were generally in agreement with the NMR data. FTIR spectra of both biooils showed the presence of both primary and secondary amides and primary amines as well as N-heterocyclics such as pyridines, quinolines, and pyrimidines. The FTIR spectrum of the char resembled that of the initial chicken manure except that the concentration of carbohydrates was lower.     

The conversion of chicken manure to biooil by fast pyrolysis I. Analyses of chicken manure,biooils and char by 13C and 1H NMR and FTIR spectrophotometry

Fast pyrolysis of chicken manure produced two biooils (Fractions I and II) and a residual char. All four materials were analyzed by chemical methods, ¹³C and 1H Nuclear Magnetic Resonance Spectrometry (¹³C and 1H NMR), and Fourier Transform Infrared Spectrosphotometry (FTIR). The char showed the highest C content and the highest aromaticity. Of the two biooils Fraction II was higher in C, yield and calorific value but lower in N than Fraction I. The S and ash content of the two biooil fractions were low. The Cross Polarization Magic Angle Spinning (CP-MAS) ¹³C NMR spectrum of the initial chicken manure showed it to be rich in cellulose, which was a major component of sawdust used as bedding material. Nuclear Magnetic Resonance (NMR) spectra of the two biooils indicated that Fraction I was less aromatic than Fraction II. Among the aromatics in the two biooils, we were able to tentatively identify N-heterocyclics like indoles, pyridines, and pyrazines. FTIR spectra were generally in agreement with the NMR data. FTIR spectra of both biooils showed the presence of both primary and secondary amides and primary amines as well as N-heterocyclics such as pyridines, quinolines, and pyrimidines. The FTIR spectrum of the char resembled that of the initial chicken manure except that the concentration of carbohydrates was lower.     

Studying soil organic matter using 13C CP-MAS NMR: the effect of soil chemical pre-treatments on spectra quality and representativity

¹³C CP-MAS NMR spectroscopy is a technique that has proved to be useful in studying soil organic matter (SOM). Nevertheless, NMR spectra exhibit a weak signal and have very low resolution due to: the low natural abundance of ¹³C (1.1 % of C) in SOM, the generally low SOM content of soils, and the presence of paramagnetic impurities. This paper studies the effects of soil chemical pre-treatments on ¹³CP-MAS NMR spectra quality and spectra representativity i.e. soil C mass balance.

After chemical pre-treatment to increase total organic carbon (TOC) content and C/Fe ratio, eight soils characterized by different levels of organic carbon content and C/Fe ratios were studied using ¹³CP-MAS NMR. Moreover, where chemical treatments were not applicable due to high carbon losses, the number of ¹³CP-MAS NMR scans was increased in order to obtain satisfactory spectra.

Results show that chemical pre-treatment of soils with C/Fe > 1 caused high C losses. Bulk soils were therefore studied by increasing the number of ¹³CP-MAS NMR scans. Acceptable spectra were obtained from 8K scans (1K = 1024 transient). On the other hand, even when a large number of scan (32K) are used, soil with C/Fe < 1 cannot be studied. As these soils are characterized by low C losses after HCl treatments (range of 2.9–25.4%), a pre-treatment of at least 1.39 mol l⁻¹ HCl removes excess Fe and at the same time increases C/Fe ratio resulting in 32K scans providing good spectra.     

Effect of biochars on adsorption of Cu(II), Pb(II) and Cd(II) by three variable charge soils from southern China

The purpose of this study is to compare the relative contribution of different mechanisms to the enhanced adsorption of Cu(II), Pb(II) and Cd(II) by variable charge soils due to incorporation of biochars derived from crop straws. The biochars were prepared from the straws of canola and peanut using an oxygen-limited pyrolysis method at 350 °C. The effect of biochars on adsorption and desorption of Cu(II), Pb(II) and Cd(II) by and from three variable charge soils from southern China was investigated with batch experiments. Based on the desorption of pre-adsorbed heavy metals, the electrostatic and non-electrostatic adsorptions were separated. EDTA was used to replace the heavy metals complexed with biochars and to evaluate the complexing ability of the biochars with the metals. The incorporation of biochars increased the adsorption of Cu(II), Pb(II) and Cd(II) by the soil; peanut straw char induced a greater increase in the adsorption of the three metals. The increased percentage of Cd(II) adsorption induced by biochars was much greater than that for the adsorption of Cu(II) and Pb(II). Cu(II) adsorption on three variable charge soils was enhanced by the two biochars mainly through a non-electrostatic mechanism, while both electrostatic and non-electrostatic mechanisms contributed to the enhanced adsorption of Pb(II) and Cd(II) due to the biochars. Peanut straw char had a greater specific adsorption capacity than canola straw char and thus induced more non-electrostatic adsorption of Cu(II), Pb(II) and Cd(II) by the soils than did the canola straw char. The complexing ability of the biochars with Cu(II) and Pb(II) was much stronger than that with Cd(II) and thus induced more specific adsorption of Cu(II) and Pb(II) by the soils than that of Cd(II). Biochars increased heavy metal adsorption by the variable charge soils through electrostatic and non-electrostatic mechanisms, and the relative contribution of the two mechanisms varied with metals and biochars.     

Chemical properties of dissolved organic matter derived from sugarcane rind and the impacts on copper adsorption onto red soil

Dissolved organic matter (DOM), as the most active organic carbon in the soil, has a coherent affinity with heavy metals from inherent and exogenous sources. Although the important roles of DOM in the adsorption of heavy metals in soil have previously been demonstrated, the heterogeneity and variability of the chemical constitution of DOM impede the investigation of its effects on heavy metal adsorption onto soil under natural conditions. Fresh DOM (FDOM) and degraded DOM (DDOM) from sugarcane rind were prepared, and their chemical properties were measured by Fourier-transform infrared spectrometry (FTIR), excitation-emission matrix (EEM) fluorescence spectroscopes, nuclear magnetic resonance (NMR), and molecular weight distribution (MWD). They were also used in batch experiments to evaluate their effects on the adsorption of Cu(II) onto farmland red soil. Based on our results, the chemical structure and composition of DDOM greatly varied; compared with FDOM, the C/O ratio (from 24.0 to 9.6%) and fluorescence index (FI) (from 1.4 to 1.0) decreased, and high molecular weight (>10 kDa) compounds increased from 23.18 to 70.51%, while low molecular weight (<3 kDa) compounds decreased from 56.13 to 12.13%; aromaticity and humification degree were markedly enhanced. The discrepancy of FDOM and DDOM in terms of chemical properties greatly influenced Cu(II) adsorption onto red soil by affecting DOM-Cu(II) complex capacity. The FDOM inhibited the adsorption of Cu(II), while DDOM promoted adsorption, which was significantly influenced by soil pH. Maximum adsorption capacity (Q _m) was 0.92 and 5.76 mg g^?1 in the presence of FDOM and DDOM, respectively. The adsorption process with DDOM could be better described by the Langmuir model, while that with FDOM was better described by the Freundlich model. The impacts caused by the dynamic changes of the chemical properties of DOM under natural conditions should therefore be considered in the risk assessment and remediation of soils contaminated with heavy metals.     

Impacts of pH and ammonia on the leaching of Cu(II) and Cd(II) from coal fly ash

Many coal-fired power plants are implementing ammonia-based technologies to reduce NO(x) emissions. Excess ammonia in the flue gas often deposits on the coal fly ash. Ammonia can form complexes with many heavy metals and change the leaching characteristics of these metals. This research tends to develop a fundamental understanding of the ammonia impact on the leaching of some heavy metals, exemplified by Cu(II) and Cd(II), under different pH conditions. Batch results indicated that the adsorption is the main mechanism controlling Cu(II) and Cd(II) leaching, and high concentrations of ammonia (>5,000 mg/l) can increase the release of Cu(II) and Cd(II) in the alkaline pH range. Based on the chemical reactions among fly ash, ammonia, and heavy metal ion, a mathematical model was developed to quantify effects of pH and ammonia on metal adsorption. The adsorption constants (logK) of Cu(2+), Cu(OH)(+), Cu(OH)(2), and Cu(NH(3))(m)(2+) for the fly ash under investigation were respectively 6.0, 7.7, 9.6, and 2.9. For Cd(II), these constants were respectively 4.3, 6.9, 8.8, and 2.6. Metal speciation calculations indicated that the formation of less adsorbable metal-ammonia complexes decreased metal adsorption, therefore enhanced metal leaching.     

Equilibrium, kinetic, and thermodynamic biosorption of Pb(II), Cr(III), and Cd(II) ions by dead anaerobic biomass from synthetic wastewater

Purpose

Heavy metals are toxic pollutants released into the environment as a result of different industrial activities. Biosorption of heavy metals from aqueous solutions is a new technology for the treatment of industrial wastewater. The aim of the present research is to highlight the basic biosorption theory to heavy metal removal.

Materials and methods

Heterogeneous cultures mostly dried anaerobic bacteria, yeast (fungi), and protozoa were used as low-cost material to remove metallic cations Pb(II), Cr(III), and Cd(II) from synthetic wastewater. Competitive biosorption of these metals was studied.

Results

The main biosorption mechanisms were complexation and physical adsorption onto natural active functional groups. It is observed that biosorption of these metals was a surface process. The main functional groups involved in these processes were hydroxyl (–OH) and carboxylic groups (C=O) with 37, 52, and 31 and 21, 14, and 34 % removal of Pb(II), Cr(III), and Cd(II), respectively. Langmuir was the best model for a single system. While extended Langmuir was the best model for binary and ternary metal systems. The maximum uptake capacities were 54.92, 34.78, and 29.99 mg/g and pore diffusion coefficients were 7.23, 3.15, and 2.76?×?10^?11 m²/s for Pb(II), Cr(III), and Cd(II), respectively. Optimum pH was found to be 4. Pseudo-second-order was the best model to predict the kinetic process. Biosorption process was exothermic and physical in nature.

Conclusions

Pb(II) offers the strongest component that is able to displace Cr(III) and Cd(II) from their sites, while Cd(II) ions are the weakest adsorbed component.     

Effect of pre-treatment and supporting media on Ni(II), Cu(II), Al(III) and Fe(III) sorption by plant root material

In this work Paspalum notatum root material was used to elucidate the influence of acid leaching pre-treatment and of sorption medium on metal adsorption. Ground P. notatum root was leached with 0.14M HNO(3). Leached root material (LRM) and non-leached root material (NLRM) were employed to flow sorption of Ni(II), Cu(II), Al(III) and Fe(III) in 0.5M CH(3)COONH(4) medium at pH 6.5. For LRM the sorption was also studied in 0.5M KNO(3) medium. The acid pre-treatment increased the sorption capacity (SC) for all ions studied. For the KNO(3) medium, Cu(II) and Fe(III) sorption was higher than in CH(3)COONH(4) and the type of the Ni(II) isotherm's model changed. The Freundlich model was the most representative isotherm model to describe metallic ions sorption. The (1)H NMR spectra showed differences between LRM and NLRM and the acid-basic potentiometric titration elucidated that acid-leaching procedure affected the root material sorption sites once only two predominant sorption sites were found for LRM (phenolic and amine, both able cations sorption) and five sorption sites (two carboxylic, amine and two phenolic) were founded for NLRM.     

Terrestrial ecotoxicity and effect factors of metals in life cycle assessment (LCA)

Life cycle impact assessment aims to translate the amounts of substance emitted during the life cycle of a product into a potential impact on the environment, which includes terrestrial ecosystems. This work suggests some possible improvements in assessing the toxicity of metals on soil ecosystems in life cycle assessment (LCA). The current available data on soil ecotoxicity allow one to calculate the chronic terrestrial HC50(EC50) (hazardous concentration affecting 50% of the species at their EC50 level, i.e. the level where 50% of the individuals of the species are affected) of nine metals and metalloids (As(III) or (V), Be(II), Cr(III) or (VI), Sb(III) or (V), Pb(II), Cu(II), Zn(II) and Ni(II)). Contrarily to what is generally advised in LCIA, the terrestrial HC50 of metals shall not be extrapolated from the aquatic HC50, using the Equilibrium Partitioning method since the partition coefficient (K(d)) of metals is highly variable. The experimental ecotoxicology generally uses metallic salts to contaminate artificial soils but the comparison of the EC50 or NOEC obtained for the same metal with different salts reveals that the kind of salt used insignificantly influences these values. In contrast, depending on the metallic fraction of concern, the EC50 may vary, as for cadmium: the EC50 of Folsomia candida, expressed as free Cd in pore water is almost 2.5 orders of magnitude lower than that expressed as total metal. A similar result is obtained with Eisenia fetida, confirming the importance of metals speciation in assessing their impact on soils. By ranking the metals according to the difference between their terrestrial and aquatic HC50 values, two groups are distinguished, which match the hard soft acids and bases (HSAB) concept. This allows to estimate their affinity for soil components and potential toxicity according to their chemical characteristics.     

Removal of Pb(II), Cd(II), Cu(II), and Zn(II) by hematite nanoparticles: effect of sorbent concentration, pH, temperature, and exhaustion

Nanoparticles offer the potential to improve environmental treatment technologies due to their unique properties. Adsorption of metal ions (Pb(II), Cd(II), Cu(II), Zn(II)) to nanohematite was examined as a function of sorbent concentration, pH, temperature, and exhaustion. Adsorption experiments were conducted with 0.05, 0.1, and 0.5 g/L nanoparticles in a pH 8 solution and in spiked San Antonio tap water. The adsorption data showed the ability of nanohematite to remove Pb, Cd, Cu, and Zn species from solution with adsorption increasing as the nanoparticle concentration increased. At 0.5 g/L nanohematite, 100 % Pb species adsorbed, 94 % Cd species adsorbed, 89 % Cu species adsorbed and 100 % Zn species adsorbed. Adsorption kinetics for all metals tested was described by a pseudo second-order rate equation with lead having the fastest rate of adsorption. The effect of temperature on adsorption showed that Pb(II), Cu(II), and Cd(II) underwent an endothermic reaction, while Zn(II) underwent an exothermic reaction. The nanoparticles were able to simultaneously remove multiple metals species (Zn, Cd, Pb, and Cu) from both a pH 8 solution and spiked San Antonio tap water. Exhaustion experiments showed that at pH 8, exhaustion did not occur for the nanoparticles but adsorption does decrease for Cd, Cu, and Zn species but not Pb species. The strong adsorption coupled with the ability to simultaneously remove multiple metal ions offers a potential remediation method for the removal of metals from water.     

Biosorption of heavy metals from aqueous solution by UV-mutant Bacillus subtilis

To develop an efficient bio-immobilization approach for the remediation of heavy metal pollution in soil, a mutant species of Bacillus subtilis (B38) was obtained by ultraviolet irradiation and selection under high concentration of cadmium (Cd) in a previous study. In the present study, to check the applicability of this mutated species to the sorption and immobilization of other metals, the sorption of four heavy metals, Cd, chromium (Cr), mercury (Hg), and lead (Pb), on living and nonliving B38 in single- and multiple-component systems under different conditions was investigated using batch experiments. Rapid metal binding occurred on both living and nonliving B38 during the beginning of the biosorption. The sorption kinetics followed the exponential equation for living biomass and the pseudo-first-order Lagergren model for nonliving biomass, with r ² values in the range of 0.9004-0.9933. The maximum adsorptive quantity of the heavy metals on B38 changed with the solution pH, temperature, biomass dose, and ionic strength. The nonliving biomass generally showed greater or similar adsorptive capacities as compared with the living biomass and was not likely to be affected by the solution parameters. The bacterium had a stronger affinity to the cationic heavy metals than to the anionic one, and the equilibrium sorption amounts were 210.6, 332.3, and 420.9 mg/g for Cd(II), Hg(II), and Pb(II), respectively. The results of binary and ternary sorption experiments indicated that the metals with the higher sorption capacity in the single-component systems showed greater inhibitory effects on the biosorption of other metal ions in the multiple-component systems, but the sorption sites of Hg and Cd or Pb are likely to be different. The results of this study illustrated that the mutant species is a promising biosorbent for the remediation of multiple heavy metals.     

Release of metals from homogeneous soil columns by wastewater from an agricultural industry

The effect of discharging olive mill wastewater (OMW) in soils on the release of metals previously retained by them is simulated by leaching homogeneous soil columns with a solution of the residue after passing solutions of Cu or Zn through the columns. The effect of other residues, previously added to the soil as composts in field experiments, on the behaviour observed in the laboratory is also discussed. OMW shows a strong power for releasing the metals retained. Previous addition of a compost made from olive mill sludge and plant refuse to the soil causes a significant reduction of the release of retained metal by liquid OMW. Previous addition of concentrated sugarbeet vinasse causes much less significant effects.     

Removal of heavy metal ions from water by complexation-assisted ultrafiltration

Toxic heavy metals in air, soil and water are global problems that are growing threat to the environment. Therefore, the removal and separation of toxic and environmentally relevant heavy metal ions are a technological challenge with respect to industrial and environmental application. A promising process for the removal of heavy metal ions from aqueous solutions involves bonding the metals to a bonding agent (such as macromolecular species), and then separating the loaded agents from wastewater by separation processes such as membrane filtration. The choice of water-soluble macroligands remains important for developing this technology. The effects of type of complexing agent, pH value and applied pressure on retention coefficients of Zn(II) and Cd(II) complexes were investigated. At best operating conditions (pH=9.0, p=300kPa) using diethylaminoethyl cellulose, the removal of Cd(2+) and Zn(2+) was more than 95% and 99%, respectively.     

In situ remediation of soils contaminated with toxic metal ions using microwave energy

Following onto our work on the in situ remediation of soils contaminated with PAH's, PCB's and other polychlorinated organic compounds using microwave energy, we now report a preliminary investigation on the in situ remediation of soils contaminated with toxic metal ions: Cd(II), Mn(II), Th(IV), Cr(III) and mainly Cr(VI). The soil is partially vitrified in the process, and extraction with hot (70 degrees C) 35% nitric acid for 4.5 h leads to the recovery of very small amounts of the metals which had been spiked into the clean soil: Cd, Mn, and Cr(III) are completely immobilized (unextractable), Th is mostly unextractable, and Cr(VI) partially extractable at very high levels of spiking, but almost completely unextractable using the US EPA Toxicity Characteristic Leaching Procedure. This suggests that contaminated soils which are not going to be used for agricultural purposes can be remediated safely to preset depths without fear of the toxic metal ions leaching out for a long time.     

Response of microbial activities to heavy metals in a neutral loamy soil treated with biosolid

Application of biosolid on land has been widespread in numerous countries for last several decades. This study performed incubation experiments by mixing a neutral loamy soil and biosolid enriched in Cu, Pb and Zn to explore how heavy metal affects soil mineralization and microbial biomass. The experimental results indicated that large nutrient, microorganism and C sources from biosolid were beneficial to microbial respiration. However, compared to the biosolid alone treatment, the supplemented Cu, Pb and Zn in biosolid reduced the mineralized C by roughly 36%. This phenomenon was probably caused by a portion of the Cu, Pb and Zn being complexed with organic matter to prevent decomposition of organic carbon by microorganisms. Equally, soil treated with biosolid increased the quantity of mineralized N by approximately five-fold and accelerated the rate of N mineralization by about one-fold compared to untreated soil. Notably, addition of heavy metals impaired the mineralization process, particularly when Pb reached about 64%. The reduced N mineralization occurred for similar reasons to the microbial respiration. The addition of biosolid in soil considerably increased the amount of mineralizable N; however, the increase was lower in biosolid-treated soil spiked by heavy metals. The addition of heavy metals in the soil-biosolid mixture clearly reduced the microbial biomasses C (MBC) and N (MBN), indicating that the microbial activities had been disrupted by the heavy metals. The microbial biomass C/N ratio had changed initially from 8 to 13 at the end of incubation period, owing to various groups of microbes expressing different mechanisms of metabolism, indicating that the microbial population had changed from bacteria to fungi, which had higher metal tolerance.     

Characterization of carbons from olive cake by sorption of wastewater pollutants

Studies has been conducted to compare the sorption properties between raw carbons made from olive cake and commercial activated carbons to remove aquatic pollutant such as heavy metal (HM), phenol (Ph), dodecylbenzenesulfonic acid-sodium salt detergent (DBSNa) and methylene blue dye (MB). Effect of acidic treatments by H2SO4, HCl and HNO3 on the sorption properties of olive cake carbon (OCC) were studied by mass titration, SEM photographs, sorption isotherms. It is found that acidic treatment changes the surface properties of OCC but do not enhance its sorption capacity. Compared to commercial activated carbons the OCC derivatives generally are equally able to uptake HM and Ph from solution but MB and DBSNa are not. This different behaviour is to attribute to manufacturing and activation treatments so as surface groups of the precursor sorbent material. For the heavy metals, chromium and silver were removed effectively but to small extent cadmium. This may be because of the various charge densities of metal elements tested. The results of the multiple experiments indicate that sorption of cadmium ions can be significantly improved by the presence of complexing agents sorbed from the carbon. An empirical mathematical form is proposed to correlate experimental data and to compare the performance of the different sorbent materials.     

Investigation on the chemical structure of nonextractable residues of the fungicide cyprodinil in spring wheat using 13C-C1-phenyl-cyprodinil on 13C-depleted plants-an alternative approach to investigate nonextractable residues

13C-labelled cyprodinil was applied on 13C-depleted wheat plants with 27-fold field application rate. A control experiment applying same amounts of 14C-cyprodinil showed that main portions of the residues were detected in the cellulose (15% NER), hemicellulose (28.3% NER), and lignin fraction (23.3% NER). 16.7% were detected in water soluble polymers, 6% in both, pectin and protein fraction, and 4% in the starch containing fraction. Free cyprodinil was detectable by TLC in all fractions except lignin. A direct characterization of the residues in vivo by CP-MAS was not successful. Cell wall fractions were further analysed by liquid state NMR to determine the structure of the mobilized highly polymer/polar residues: Within lignin, where most of the residues were located at field application rate, neither intact cyprodinil nor its metabolites could not be detected. The 13C-label introduced was probably incorporated in the polymer as natural lignin monomers and thus are not considered as bound residues according to IUPAC definition.     

Spatial and temporal organic and heavy metal pollution at Mai Po Marshes Nature Reserve,Hong Kong

An intensive monthly sampling of water and sediments from 12 sites over 8 months covering wet and dry seasons at Mai Po Marshes Nature Reserve was conducted during June 1997-February 1998. Major organic (C, N and P) and heavy metal pollutants (Cd, Cr, Cu, Ni, Pb, Zn) water and sediment samples were examined. The results showed that Mai Po Marshes were severely polluted by organic matter and heavy metals, and the water from Deep Bay appeared to be the source of pollution. Up to 13-55% chance that the sediments of Mai Po Marshes were classified as moderately to seriously metal contaminated materials, according to the guideline set by Hong Kong Government. Empirical models describing organic matter and heavy metal spatial and seasonal dynamics in the water and sediments were formulated, based on data analysis. During wet season (June-October), more than 58% variations of total P can be explained by ortho-P in water, while ammonia-N explained up to 90% variations of total Kjeldahl nitrogen in water. Throughout the whole sampling period (June-February), there were significant correlations (p<0.01) between total organic C in water. pH in the sediments and salinity in water appeared to be important factors determining heavy metal mobility in sediments, while potential metal release from the sediments is a concern when any oxidizing processes such as flooding or dredging are imposed on sediments.     

Characterization and Cu sorption properties of humic acid from the decomposition of rice straw

Humic acid (HA) derived from rice straw decomposed for 1 (HA-1), 3 (HA-3), 6 (HA-6) and 12 (HA-12) months was characterized by potentiometric titration and solid-state cross-polarization magic-angle spinning ¹³C nuclear magnetic resonance spectroscopy (CPMAS ¹³C NMR). The sorption of Cu on examined HA was investigated using a combination of batch sorption, isothermal titration calorimetry (ITC) and sequential desorption. Results showed that the functional group content and the humification degree of HA tended to increase with increasing decomposition time especially in the latter stage of examined decomposition period. Cu sorption on HA was a rapid process that occurred within the first 1 h and the sorption capacity increased from 245.4 mmol kg⁻¹ on HA-1 to 294.6 mmol kg⁻¹ on HA-12. The sorption of Cu was endothermic, spontaneous and the randomness was increased during Cu sorption. Sorbed Cu on examined HA can be hardly released by NH₄Ac but nearly fully released by EDTA. Forming inner-sphere complexes was the main mechanism of Cu sorption on examined HA. This study could provide valuable information for a better understanding on the environmental impacts of the decomposition of organic waste.