Development,validation, and application of a method for the GC-MS analysis of fipronil and three of its degradation products in samples of water,soil, and sediment

A method for the identification and quantification of pesticide residues in water, soil, and sediment samples has been developed, validated, and applied for the analysis of real samples. The specificity was determined by the retention time and the confirmation and quantification of analyte ions. Linearity was demonstrated over the concentration range of 20 to 120 µg L^?1, and the correlation coefficients varied between 0.979 and 0.996, depending on the analytes. The recovery rates for all analytes in the studied matrix were between 86% and 112%. The intermediate precision and repeatability were determined at three concentration levels (40, 80, and 120 µg L^?1), with the relative standard deviation for the intermediate precision between 1% and 5.3% and the repeatability varying between 2% and 13.4% for individual analytes. The limits of detection and quantification for fipronil, fipronil sulfide, fipronil-sulfone, and fipronil-desulfinyl were 6.2, 3.0, 6.6, and 4.0 ng L^?1 and 20.4, 9.0, 21.6, and 13.0 ng L^?1, respectively. The method developed was used in water, soil, and sediment samples containing 2.1 mg L^?1 and 1.2% and 5.3% of carbon, respectively. The recovery of pesticides in the environmental matrices varied from 88.26 to 109.63% for the lowest fortification level (40 and 100 µg kg^?1), from 91.17 to 110.18% for the intermediate level (80 and 200 µg kg^?1), and from 89.09 to 109.82% for the highest fortification level (120 and 300 µg kg^?1). The relative standard deviation for the recovery of pesticides was under 15%.     

Suitability of passive sampling for the monitoring of pharmaceuticals in Finnish surface waters

The occurrence of five pharmaceuticals, consisting of four anti-inflammatory and one antiepileptic drug, was studied by passive sampling and grab sampling in northern Lake Päijänne and River Vantaa. The passive sampling was performed by using Chemcatcher® sampler with a SDB-RPS Empore disk as a receiving phase. In Lake Päijänne, the sampling was conducted during summer 2013 at four locations near the discharge point of a wastewater treatment plant and in the years 2013 and 2015 at four locations along River Vantaa. The samples were analyzed by liquid chromatography coupled to tandem mass spectrometry (LC-MS/MS) in the multiple reaction monitoring mode. The concentrations of carbamazepine, diclofenac, ibuprofen, ketoprofen, and naproxen in Lake Päijänne determined by passive sampling ranged between 1.4–2.9 ng L^?1, 15–35 ng L^?1, 13–31 ng L^?1, 16–27 ng L^?1, and 3.3–32 ng L^?1, respectively. Similarly, the results in River Vantaa ranged between 1.2–40 ng L^?1, 15–65 ng L^?1, 13–33 ng L^?1, 16–31 ng L^?1, and 3.3–6.4 ng L^?1. The results suggest that the Chemcatcher passive samplers are suitable for detecting pharmaceuticals in lake and river waters.     

Extraction of Sudan dyes from environmental water by hemimicelles-based magnetic titanium dioxide nanoparticles

A novel method for the extraction of Sudan dyes including Sudan I, II, III, and IV from environmental water by magnetic titanium dioxide nanoparticles (Fe₃O₄@TiO₂) coated with sodium dodecylsulfate (SDS) as adsorbent was reported. Fe₃O₄@TiO₂ was synthesized by a simple method and was characterized by transmission electron microscopy, Fourier-transform infrared spectrometry, and vibrating sample magnetometer. The magnetic separation was quite efficient for the adsorption and desorption of Sudan dyes. The effect of the amount of SDS, extraction time, pH, desorption condition, maximal extraction volume, and humic acid on the extraction process were investigated. This method was employed to analyze three environmental water samples. The results demonstrated that our proposed method had wide linear range (25–5,000 ng L^?1) with a good linearity (R ²?>?0.999) and low detection limits (2.9–7.3 ng L^?1). An enrichment factor of 1,000 was achieved. In all three spiked levels (25, 250, and 2,500 ng L^?1), the recoveries of Sudan dyes were in the range of 86.9–93.6 %. The relative standard deviations obtained were ranging from 2.5 to 9.3 %. That is to say, the new method was fast and effective for the extraction of Sudan dye from environmental water.     

Tea bag filter paper as a novel protective membrane for micro-solid phase extraction of butachlor in aqueous samples

An innovative, cost-effective, simple, and environmental friendly tea bag filter paper protected micro-solid phase extraction (μ-SPE) technique was developed for the first time with the aim to miniaturize and minimize the use of organic solvents for the extraction and determination of butachlor in aqueous samples. The μ-SPE device was produced by packing 3.0 mg of an easily synthesized new sorbent, hydroxyl-functionalized polypyrrole (OH-PPY), inside a small tea bag filter paper sachet (1.0 cm × 0.5 cm) that served as a protective envelope. Both the extraction and desorption procedures were facilitated by sonication. Due to the high porosity and the fast water absorption of the tea bag filter paper, the analyte could easily diffuse through and enhance the interaction with the sorbent. Under the optimized conditions for the GC-ECD and the μ-SPE, the limit of detection (S/N ≥ 3) was 2.0 μg L^?1 while the limit of quantitation (S/N ≥ 10) was 10.0 μg L^?1. The recoveries of the butachlor spiked at 0.050, 0.10, and 0.50 μg mL^?1 ranged from 77.9 ± 3.0 to 112.5 ± 2.9%. The proposed method was successfully applied for the determination of butachlor in water samples from paddy cultivation sites. The levels found were from non-detectable to 24.71 ± 0.37 μg L^?1.     

Analysis of Herbicide Krovar I™ by Liquid Chromatography with Atmospheric Pressure Chemical Ionization Mass Spectrometry

Abstract

A simple, very efficient method is presented for routine analysis of herbicide Krovar I? (active components bromacil and diuron) in water and soil samples. Water samples were extracted by liquid–liquid extraction with dichloromethane (DCM) as extraction solvent. For soil samples two different extraction techniques were compared: microwave-assisted solvent extraction and a shaking technique using a platform shaker. Extracts were analyzed by high performance liquid chromatography using a water:methanol gradient. Liquid chromatography was coupled with atmospheric pressure chemical ionization mass spectrometry (LC-APCI-MS) for quantification of bromacil and diuron. Optimization of the APCI-MS was done by using standards in the flow injection analysis mode (FIA). Method detection limit for liquid samples for bromacil is 0.04 µg L^?1 and for diuron 0.03 µg L^?1. Method detection limit for soil samples is 0.01 µg g^?1 dry weight for both compounds. Results of analysis of field samples of water and soil are also presented.     

Easy and fast extraction methods to determine organochlorine pesticides in sewage sludge,soil, and water samples based at low temperature

Organochlorine pesticides present in sewage sludge can contaminate soil and water when they are used as either fertilizer or agricultural soil conditioner. In this study, the technique solid–liquid extraction with low temperature purification was optimized and validated for determination of ten organochlorine pesticides in sewage sludge and soil samples. Liquid–liquid extraction with low temperature purification was also validated for the same compounds in water. Analyses were performed by gas chromatography-mass spectrometry operating in the selective ion monitoring mode. After optimization, the methods showed recoveries between 70% and 115% with relative standard deviation lower than 13% for all target analytes in the three matrices. The linearity was demonstrated in the range of 20 to 70 µg L^?1, 0.5 to 60 µg L^?1, and 3 to 13 µg L^?1, for sludge, soil, and acetonitrile, respectively. The limit of quantification ranged between 2 and 40 µg kg^?1, 1 and 6 µg kg^?1, and 0.5 µg L^?1 for sludge, soil, and water, respectively. The methods were used in the study of pesticide lixiviation carried out in a poly vinyl chlorine column filled with soil, which had its surface layer mixed with sludge. The results showed that pesticides are not leached into soil, part of them is adsorbed by the sewage sludge (4–40%), and most pesticides are lost by volatilization.     

Determination of phenols and pharmaceuticals in municipal wastewaters from Polish treatment plants by ultrasound-assisted emulsification–microextraction followed by GC–MS

A method combining ultrasound-assisted emulsification–microextraction (USAEME) with gas chromatography–mass spectrometry (GC–MS) was developed for simultaneous determination of four acidic pharmaceuticals, ibuprofen, naproxen, ketoprofen, and diclofenac, as well as four phenols, 4-octylphenol, 4-n-nonylphenol, bisphenol A, and triclosan in municipal wastewaters. Conditions of extraction and simultaneous derivatization were optimized with respect to such aspects as type and volume of extraction solvent, volume of derivatization reagent, kind and amount of buffering salt, location of the test tube in the ultrasonic bath, and extraction time. The average correlation coefficient of the calibration curves was 0.9946. The LOD/(LOQ) values in influent and effluent wastewater were in the range of 0.002–0.121/(0.005–0.403) μg L^?1 and 0.002–0.828/(0.006–2.758) μg L^?1, respectively. Quantitative recoveries (≥94 %) and satisfactory precision (average RSD 8.2 %) were obtained. The optimized USAEME/GC–MS method was applied for determination of the considered pharmaceuticals and phenols in influents and treated effluents from nine Polish municipal wastewater treatment plants. The average concentration of acidic pharmaceuticals in influent and effluent wastewater were in the range of 0.06–551.96 μg L^?1 and 0.01–22.61 μg L^?1, respectively, while for phenols were in the range of 0.03–102.54 μg L^?1 and 0.02–10.84 μg L^?1, respectively. The removal efficiencies of the target compounds during purification process were between 84 and 99 %.     

Fast extraction of polychlorinated dibenzo-p-dioxin and polychlorinated dibenzofuran in sewage sludge and soil samples

The current environmental legislations recommend monitoring chemical contaminants such as polychlorinated dibenzo-p-dioxins and polychlorinated dibenzofurans before the use of sewage sludge on the agricultural land. In this study, a solid–liquid extraction with low-temperature purification (SLE-LTP) was optimized and validated to determine 2,3,7,8-tetrachlorodibenzo-p-dioxin and 2,3,7,8-tetrachlorodibenzofuran in sewage sludge and soil samples. The analyses were performed by gas chromatography-mass spectrometry operating in the selective ion mode (GC-MS-SIM). Acetonitrile:ethyl acetate 6.5:1.5 (v/v) was the best extraction phase, and the recoveries percentages were close to 100%. The linearity was demonstrated in the range of 1.25–25 µg L^?1 of 1.25–20 µg L^?1 for sewage sludge and soil, respectively. Matrix effect was proved for the two compounds and in the two matrices studied. Extraction percentages were between 78 and 109% and relative standard deviations ≤ 19%. The proposed method is faster than methods described in the literature because showed a few steps. The quantification limits (LOQ) in sewage sludge were 6.4 and 32 ng TEQ kg^?1 for 2,3,7,8-TCDF and 2,3,7,8-TCDD, respectively. In soil, LOQs were 0.8 and 8.0 ng TEQ kg^?1 for 2,3,7,8-TCDF and 2,3,7,8-TCDD, respectively. These values are lower than the maximum residue limits established by European Legislation. The method was applied to 22 agricultural soil samples from different Brazilian cities and 2,3,7,8-TCDF was detected in one of these samples.     

Assessment of commercially available polymeric materials for sorptive microextraction of priority and emerging nonpolar organic pollutants in environmental water samples

Among the different organic pollutants, persistent organic pollutants and emerging organic contaminants (EOCs) are of particular concern due to their potentially dangerous effects on the ecosystems and on human health. In the framework of the analysis of some of these organic pollutants in water samples, sorptive extraction devices have proven to be adequate for their monitoring. The efficiency of four commercially available and low-cost polymeric materials [polypropylene, poly(ethylene terephthalate), Raffia, and polyethersulfone (PES)] for the simultaneous extraction of 16 organic compounds from five different families from environmental water samples was evaluated in this work. Firstly, the homogeneity of the sorbent materials was confirmed by means of Raman spectroscopy. After the optimization of the parameters affecting the extraction and the liquid desorption steps, it was found that PES showed the largest efficiencies for slightly polar analytes and, to a lesser extent, for nonpolar analytes. Additionally, Raffia rendered good extraction efficiencies for nonpolar compounds. Thus sorptive extraction methods followed by large volume injection-programmable temperature vaporizer-gas chromatography-mass spectrometry were validated using PES and Raffia as sorbent materials. The validation of the method provided good linearity (0.978?r ²?r ²?-1 level). Finally, these materials were applied to the analysis of contaminants in environmental water samples.     

Determination of etoxazole residues in fruits and vegetables by SPE clean-up and HPLC-DAD

A method for determination of etoxazole residues in apples, strawberries and green beans was developed and validated. The analyte was extracted with acetonitrile from foodstuff and a charcoal-celite cartridge was used for clean-up of raw extracts. Reversed phase high performance liquid chromatography with photodiode array detector (HPLC-DAD) was used for the determination and quantification of etoxazole residues in the studied samples. The calibration graphs of etoxazole in a solvent or three blank matrixes were linear within the tested intervals 0.01–2 mg L^?1, with correlation coefficient of determination >0.999. The combined solid phase extraction (SPE) clean-up and the chromatographic method steps were sensitive and reliable for simultaneous determination of etoxazole residues in the studied samples. The average recoveries of etoxazole in the tested foodstuffs were between 93.4 to 102% at spiking levels of 0.01, 0.10, and 0.50 mg kg^?1, with relative standard deviations ranging from 2.8 to 4.7%, in agreement with directives for method validation in residue analyses. The limit of detection (LOD) of the HPLC-DAD system was 100 pg. The limit of quantification of the entire method was 0.01 mg kg^?1.     

Development and validation of LC-MS/MS method for the determination of Ochratoxin A and its metabolite Ochratoxin α in poultry tissues and eggs

The objective of this study was to develop a liquid chromatography tandem mass spectrometry (LC-MS/MS) method for the determination of Ochratoxin A (OTA) and Ochratoxin α (OTα) in poultry tissues and eggs. The two toxins were extracted by a mixture of acetonitrile/water, purified with a reversed phase C18 solid phase extraction column (SPE) and determined by LC-MS/MS. The LC-MS/MS method performances were evaluated in terms of linearity in solvent and in matrix (ranged from 0.5 to 15.10 µg L^?1 for OTA and from 0.60 to 17.85 µg L^?1 for OTα), limit of detection (LOD), limit of quantitation (LOQ), specificity, accuracy and precision in repeatability conditions. Recovery experiments were performed by spiking poultry liver, kidney, muscle and eggs around 1 µg kg^?1 and 10 µg kg^?1. LODs were 0.27 and 0.26 µg kg^?1 while LOQs were fixed at 1.0 and 1.2 µg kg^?1 for OTA and OTα, respectively. Main recoveries for OTA ranged from 82 to 109% and for OTα ranged from 55 to 89%. The values of within-laboratory relative standard deviation (RSD_r) were equal to or below 20%. Considering the results obtained and that all analytical performance criteria were fulfilled, the new extraction and purification method developed for OTA and OTα determination in animal tissues and eggs was found appropriate for control laboratories and research activities designed to ensure food safety.     

Fast determination of sulfonamides and their acetylated metabolites from environmental water based on magnetic molecularly imprinted polymers

Group-selective magnetic molecularly imprinted polymers (MMIPs) that can extract four widely used sulfonamide antibiotics and their acetylated metabolites from environmental water were synthesized in this study. The MMIPs with saturation magnetization value of 16.7 emu g^-1 could be separated from the environmental water samples easily by the application of an adscititious magnetic field, reducing the time consumption of pretreatment. The extraction conditions were evaluated, and optimal extraction conditions were as follows: extraction time, 25 min; amount of polymers, 90 mg; washing solvent, 30 % methanol aqueous solution; and elution solvent, methanol–acetic acid (95:5, v/v). The target analytes were detected by liquid chromatography–tandem mass spectrometry, and the detection limits of the method are in the range of 0.38–1.32 ng L^-1. The relative standard deviations of intra- and inter-day are in the range of 1.3–6.8 % and 1.7–9.1 %, respectively. The proposed method is suitable for the analysis of environmental water samples.     

Novel pipette-tip graphene/poly (vinyl alcohol) cryogel composite extractor for the analysis of carbofuran and carbaryl in water

A novel pipette-tip extractor of a graphene/poly (vinyl alcohol) cryogel (graphene/PVA) composite sorbent was prepared to preconcentrate carbamate pesticides in environmental water samples before analysis with a gas chromatograph-flame ionization detector (GC-FID). This novel pipette-tip extractor with the graphene/PVA sorbent exhibited a high porosity when observed through a scanning electron micrograph (SEM). Under optimal conditions, using only 1.0 mL of sample and 0.75 mL of eluting solvent, the developed method provided a wide linear range of 10–700 ng mL^?1 and 10–500 ng mL^?1 with limit of detection (LOD) of 6.40 ± 0.18 and 9.17 ± 0.34 ng mL^?1 for carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) and carbaryl (1-naphthyl methylcarbamate), respectively. The pipette-tip extractor provided high extraction efficiency with high accuracy indicated, by good recoveries in the range of 74.5 ± 4.8% to 119.7 ± 1.6% and 76 ± 15% to 114 ± 19% for carbofuran and carbaryl, respectively. In addition, the fabrication procedure showed a good pipette-tip extractor-to-pipette-tip extractor reproducibility with a relative standard deviation of 1.3–9.8% (n = 5). When the developed pipette-tip extractor was applied for the extraction of carbofuran and carbaryl in surface water samples near vegetable plantation areas, 25.9 ± 8.2 ng mL^?1 of carbofuran was found, and carbaryl was also detected in concentrations that ranged from 45.0 ± 4.0 to 191 ± 13 ng mL^?1.     

Simultaneous gas chromatographic determination of chlorpyrifos and its impurity sulfotep in liquid pesticide formulations

An analytical method for simultaneous determination of the active substance (chlorpyrifos) and its relevant impurity (sulfotep) in commercial pesticide formulations has been developed and validated. The proposed method entails extraction of the analytes from samples by sonication with acetone and analysis by gas chromatography-flame ionization detection (GC-FID). The proposed method was characterized by satisfactory accuracy and precision. The repeatability expressed as relative standard deviation (RSD) was lower than the acceptable values calculated from the modified Horwitz equation whereas individual recoveries were in the range of 98–102% and 80–120% for chlorpyrifos and sulfotep, respectively. The limit of quantification (LOQ) for the impurity (sulfotep) was 0.003 mg mL^?1 corresponding to the maximum permitted level according to Food and Agricultural Organization of the United Nations (FAO) specifications for the active substance (chlorpyrifos) being 3 g kg^?1 of the chlorpyrifos content found. The main advantage of the proposed method was a considerable reduction in the analysis time since both analytes were determined based on a single injection into the GC-FID. Analysis of real samples of commercial pesticide formulations confirmed fitness-for-purpose of the proposed method.     

Leaching of S-metolachlor,terbuthylazine, desethyl-terbuthylazine,mesotrione, flufenacet,isoxaflutole, and diketonitrile in field lysimeters as affected by the time elapsed between spraying and first leaching event

The effect of elapsed time between spraying and first leaching event on the leaching behavior of five herbicides (terbuthylazine, S-metolachlor, mesotrione, flufenacet, and isoxaflutole) and two metabolites (desethyl-terbuthylazine and diketonitrile) was evaluated in a 2011–2012 study in northwest Italy. A battery of 12 lysimeters (8.4 m² long with a depth of 1.8 m) were used in the study, each filled with silty-loam soil and treated during pre-emergence with the selected herbicides by applying a mixture of commercial products Lumax (4 L ha^?1) and Merlin Gold (1 L ha^?1). During treatment periods, no gravity water was present in lysimeters. Irrigation events capable of producing leaching (40 mm) were conducted on independent groups of three lysimeters on 1 day after treatment (1 DAT), 7 DAT, 14 DAT, and 28 DAT. The series was then repeated 14 days later. Leachate samples were collected a few days after irrigation; compounds were extracted by solid phase extraction and analyzed by high-performance liquid chromatography and gas chromatography–mass spectrometry. Under study conditions, terbuthylazine and S-metolachlor showed the highest leaching potentials. Specifically, S-metolachlor concentrations were always found above 0.25 µg L^?1. Desethyl-terbuthylazine was often detected in leached waters, in most cases at concentrations above 0.1 µg L^?1. Flufenacet leached only when irrigation occurred close to the time of herbicide spraying. Isoxaflutole and mesotrione were not measured (<0.1 µg L^?1), while diketonitrile was detected in concentrations above 0.1 µg L^?1 on 1 DAT in 2011 only.     

Simultaneous determination of eight metabolites of organophosphate and pyrethroid pesticides in urine

A simultaneous method for quantifying eight metabolites of organophosphate pesticides and pyrethroid pesticides in urine samples has been established. The analytes were extracted using liquid–liquid extraction coupled with WCX solid phase extraction (SPE) cartridges. Eight metabolites were chemically derivatized before analysis using gas chromatography–tandem mass spectrometry (GC–MS–MS). The separation was performed on a HP-5MS capillary column (30 m × 0.25 mm × 0.25 µm) with temperature programming. The detection was performed under electro-spray ionization (ESI) in multiple reaction monitoring (MRM) mode. An internal standard method was used. The extraction solvent, types of SPE cartridges and eluents were optimized by comparing the sample recoveries under different conditions. The results showed that the calibration curves of the five organophosphorus pesticides metabolites were linear in the range of 0.2–200 μg/L (r² ≥ 0.992) and that of the three pyrethroid pesticides metabolites were linear in the range of 0.025–250 μg/L (r² ≥ 0.991). The limits of detection (LODs, S/N ≥ 3) and the limits of quantification (LOQs, S/N ≥ 10) of the eight metabolites were 0.008–0.833 μg/L and 0.25–2.5 μg/L, respectively. The recoveries of the eight metabolites ranged from 54.08% to 82.49%. This efficient, stable, and cost-effective method is adequate to handle the large number of samples required for surveying the exposure level of organophosphorus and pyrethroid pesticides in the general population.     

Multiresidue method for high-performance liquid chromatography determination of carbamate pesticides residues in tea samples

A multiresidue method was developed to determine 19 carbamate pesticides in tea samples. Optimizations of different parameters, such as the type of extraction solvents, clean-up cartridges, and elution solvents were carried out. The developed method used acetonitrile as extraction solvent, amino cartridge for adsorbents and acetone-n-hexane as the eluting solution. Nineteen carbamate residues were then analyzed by high-pressure liquid chromatography (HPLC) with fluorescence detector. The present results showed good linearity by correlation coefficients of more than 0.9999 for all analyses. Limits of detection and quantification varied from 0.0005–0.023 mg L^{? 1}, 0.008–0.077 mg L^{? 1}, respectively. Recoveries of sixteen carbamate pesticides ranged from 65% to 135% at the spiked level of 0.5, 1.0 and 2.0 mg L^{? 1}. The relative standard deviations were lower than 20% and coefficient of variations were lower than 15%. The results indicate that the proposed method provides an effective multi and trace level screening determination of carbamate pesticides residues for tea samples.     

Rapid metal extractability tests from polluted mining soils by ultrasound probe sonication and microwave-assisted extraction systems

Ultrasonic probe sonication (UPS) and microwave-assisted extraction (MAE) were used for rapid single extraction of Cd, Cr, Cu, Ni, Pb, and Zn from soils polluted by former mining activities (Mónica Mine, Bustarviejo, NW Madrid, Spain), using 0.01 mol L^?1 calcium chloride (CaCl₂), 0.43 mol L^?1 acetic acid (CH₃COOH), and 0.05 mol L^?1 ethylenediaminetetraacetic acid (EDTA) at pH 7 as extracting agents. The optimum extraction conditions by UPS consisted of an extraction time of 2 min for both CaCl₂ and EDTA extractions and 15 min for CH₃COOH extraction, at 30% ultrasound (US) amplitude, whereas in the case of MAE, they consisted of 5 min at 50 °C for both CaCl₂ and EDTA extractions and 15 min at 120 °C for CH₃COOH extraction. Extractable concentrations were determined by inductively coupled plasma atomic emission spectrometry (ICP-AES). The proposed methods were compared with a reduced version of the corresponding single extraction procedures proposed by the Standards, Measurements and Testing Programme (SM&T). The results obtained showed a great variability on extraction percentages, depending on the metal, the total concentration level and the soil sample, reaching high values in some areas. However, the correlation analysis showed that total concentration is the most relevant factor for element extractability in these soil samples. From the results obtained, the application of the accelerated extraction procedures, such as MAE and UPS, could be considered a useful approach to evaluate rapidly the extractability of the metals studied.     

High-performance liquid chromatography (HPLC) as a tool for monitoring the fate of fluazinam in soil

Fluazinam is a widely used pesticide employed against the fungal disease late blight in potato cultivation. A specific, repeatable, and rapid high-performance liquid chromatography (HPLC) method utilizing a diode array detector (DAD) was developed to determine the presence of fluazinam in soil. The method consists of acetonitrile (ACN) extraction, clean-up with solid-phase extraction (SPE), and separation using a mobile phase consisting of 70% ACN and 30% water (v/v), including 0.02% acetic acid. HPLC was performed with a C18 column and the detection wavelength was 240 nm. The method was successfully applied to an incubation experiment and to soil samples taken from potato fields where fluazinam had been applied two to three times during the on-going growing season. In the 90-day incubation experiment, analytical standard fluazinam and the commercial fungicide Shirlan^® were added to soil samples that had never been treated with fluazinam, and were then extracted with ACN and 0.01 M calcium chloride (CaCl₂). Fluazinam was not extractable with CaCl₂, indicating that it does not leach to watercourses in the dissolved form. Recovery with ACN extraction for sandy soils was 72–95% immediately after application and 53–73% after 90 days of incubation. Out of the eight potato field soil samples, fluazinam was found in two samples at concentrations of 2.1 mg kg^?1 and 1.9 mg kg^?1, well above the limit of quantification (0.1 mg kg^?1).     

Trace analysis of parabens preservatives in drinking water treatment sludge,treated, and mineral water samples

Parabens have been widely used as antimicrobial agents, mainly in food products, pharmaceuticals, and cosmetics. Although they are known as safe preservatives, they also cause some harm to human health, which has been discussed lately. Therefore, the aim of this study was to evaluate the occurrence of nine parabens (including isomers) in mineral and drinking waters, besides in drinking water treatment sludge (DWTS) samples with determination by liquid chromatography tandem mass spectrometry (LC-MS/MS). Both methods solid phase extraction (SPE) and QuEChERS were validated. Calibration curves showed a correlation coefficient of 0.99 for all compounds. LOQ values ranged from 0.04 to 4 μg L^?1 in aqueous matrices and from 5 to 500 ng g^?1 in DWTS. Recoveries between 70 and 115% were reached with RSD below 20% for all compounds in SPE whereas recoveries between 62 and 119% were found with RSD below 20% for almost all compounds in QuEChERS. Matrix effect had low values (<?20%); it was only above 20% for methylparaben in the SPE and for pentylparaben in the QuEChERS. Using a quick and simple extraction procedures with SPE, QuEChERS, and LC-MS/MS analyses, these methods proved to be selective and sensitive. They were successfully applied to real samples (treated water, mineral water, and sludge), and methylparaben was detected at concentration levels below 0.242 μg L^?1 in mineral and treated water samples and 10 ng g^?1 in DWTS samples.