Photooxidative removal of the herbicide Acid Blue 9 in the presence of hydrogen peroxide: modeling of the reaction for evaluation of electrical energy per order (EEO)

The present work deals with photooxidative removal of the herbicide, Acid Blue 9 (AB9), in water in the presence of hydrogen peroxide (H₂O₂) under UV light illumination (30 W). The influence of the basic operational parameters such as amount of H₂O₂, irradiation time and initial concentration of AB9 on the photodegradation efficiency of the herbicide was investigated. The degradation rate of AB9 was not appreciably high when the photolysis was carried out in the absence of H₂O₂ and it was negligible in the absence of UV light. The photooxidative removal of the herbicide was found to follow pseudo-first-order kinetic, and hence the figure-of-merit electrical energy per order (E_Eo) was considered appropriate for estimating the electrical energy efficiency. A mathematical relation between the apparent reaction rate constant and H₂O₂ used was applied for prediction of the electricity consumption in the photooxidative removal of AB9. The results indicated that this kinetic model, based on the initial rates of degradation, provided good prediction of the E_Eo values for a variety of conditions. The results also indicated that the UV/H₂O₂ process was appropriate as the effective treatment method for removal of AB9 from the contaminated wastewater.     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.     

O3/H2O2处理嘧啶废水的研究

采用O3/H2O2法对嘧啶废水进行处理,考察了不同反应条件对嘧啶和COD去除率的影响,并对O3/H2O2降解嘧啶的反应机制和动力学进行了初步探讨.实验结果表明,在pH值为11,反应时间为70 min,O3流量为4g/h,H2O2投加量为50 mmol/L的条件下,废水的嘧啶和COD的去除率分别达到86.46%和74.9...     

Removal of AOX, total nitrogen and chlorinated lignin from bleached Kraft mill effluents by UV oxidation in the presence of hydrogen peroxide utilizing TiO2 as photocatalyst

Background, aim, and scope  The pulp and paper industry is the sixth largest polluter discharging a variety of gaseous, liquid, and solid wastes into the environment. Effluents from bleached Kraft mill effluents (BKME) are polluting waters to a great extent These effluents cause considerable damage to the receiving waters if discharged untreated since they have high levels of biological oxygen demand (BOD), chemical oxygen demand (COD), chlorinated compounds (measured as AOX), suspended solids (mainly fibers), fatty acids, tannins, resin acids, lignin and its derivatives, sulfur and sulfur compounds, etc. This study aimed to remove adsorbed organic halogen (AOX), total nitrogen, and lignin-degrading products in the wastewater (4,500 m³/h) from the paper mill in the pulp and paper industry, which is discharged to sea from a plant located in western Turkey. Materials and methods  The photocatalytic degradation of AOX, total nitrogen, and chlorinated lignin in BKME have been investigated in different parameters, such as time, H₂O₂ and TiO₂ concentration. In addition, for investigating the effect of chlorine on the removal of lignin, pure lignin solution was prepared in equal amounts to chlorinated lignin degradation products found in BKME. The same experiments were conducted for this solution. Experiments were carried out in photocatalytic reactor made of Pyrex glass. The mercury lamp was used as a radiation source. All irradiation was carried out under constant stirring. The existence of dissolved O₂ is an important factor which increases the photocatalytic degradation. Hence, we used an air pump for the aeration of the wastewater solutions. The temperature of the wastewater was controlled and adjusted to 25°C by thermostat pump in conjunction with a cooler. At the end of all experiments, AOX, total nitrogen and lignin concentrations were analyzed according to standard methods. All experiments were performed in duplicate and average values were used. Results and discussion  When the effect of H₂O₂ and time were investigated, it was observed that the AOX concentration increased from 3.0 to 11.0 mg/L by only UV. However, when H₂O₂ was added, AOX concentration decreased from approximately 3.0 to 0.0 mg/L. The optimal conditions for the removal of AOX appear to be an initial H₂O₂ concentration of 20.0 mL/L and reaction time of 50 min. In addition, at the same experiment conditions, it was seen that the total nitrogen concentration decreased from 23.0 to 15.0 mg/L by only UV and by increasing H₂O₂ concentration, the concentration of 20.0 mL/L H₂O₂ appears to be optimal (9.0 mg/L). The AOX, total nitrogen and lignin degradation products and pure lignin go through a minimum when the concentration of H₂O₂ and TiO₂ increases at constant pH and UV intensity. The kinetics for the degradation of AOX, total nitrogen and lignin degradation products followed a pseudo-first order law with respect to the products, and the degradation rates (min⁻¹) for the UV/TiO₂/H₂O₂ system were higher than that of the corresponding values for the UV/H₂O₂ system. Conclusions  The AOX, total nitrogen and lignin concentration go through a minimum when the concentration of H₂O₂ and TiO₂ increases at constant pH and UV intensity. It was found that the UV/TiO₂/H₂O₂ system has proved capable of the degradation of total nitrogen as well as chlorinated and degraded lignin in BKME. Recommendations and perspectives  The photocatalytic process can be considered a suitable alternative for the remove of some compounds from the BKME. Nevertheless, further studies should be carried out to confirm the practical feasibility of BKME. Another result obtained from the study is that pre-purification carried out with UV/TiO₂/H₂O₂ photocatalytic process may constitute an important step for further purification processes such as adsorption, membrane processes, etc.     

Carbofuran removal in continuous-photocatalytic reactor: Reactor optimization,rate-constant determination and carbofuran degradation pathway analysis

Carbofuran (CBF) removal in a continuous-flow photocatalytic reactor with granular activated carbon supported titanium dioxide (GAC-TiO₂) catalyst was investigated. The effects of feed flow rate, TiO₂ concentration and addition of supplementary oxidants on CBF removal were investigated. The central composite design (CCD) was used to design the experiments and to estimate the effects of feed flow rate and TiO₂ concentration on CBF removal. The outcome of CCD experiments demonstrated that reactor performance was influenced mainly by feed flow rate compared to TiO₂ concentration. A second-order polynomial model developed based on CCD experiments fitted the experimental data with good correlation (R² ～ 0.964). The addition of 1 mL min^?1 hydrogen peroxide has shown complete CBF degradation and 76% chemical oxygen demand removal under the following operating conditions of CBF ～50 mg L^?1, TiO₂ ～5 mg L^?1 and feed flow rate ～82.5 mL min^?1. Rate constant of the photodegradation process was also calculated by applying the kinetic data in pseudo-first-order kinetics. Four major degradation intermediates of CBF were identified using GC-MS analysis. As a whole, the reactor system and GAC-TiO₂ catalyst used could be constructive in cost-effective CBF removal with no impact to receiving environment through getaway of photocatalyst.     

Photocatalytic oxidation of xenobiotics in water with immobilized TIO2 on agitator

Abstract

A novel photocatalytic oxidation reactor, using Degussa P‐25 T_iO₂ as a stationary phase with a thickness of 1.5–2.0 um on the blades of agitator, was developed to study the photocatalytic oxidation of xenobiotics. Particularly in this device, separation of photocatalyst from the purified water after oxidation reaction was not necessary, and no other aeration equipment was required to supply oxygen. To examine the efficiency of this device, photocatalytic degradation of xenobiotic organics such as carbofuran was studied as an example. Results indicated that carbofuran could be degraded completely with mineralization efficiency of 20 % after 6 hours of oxidation under the imposed conditions. The mineralization rate of carbofuran was found to follow the pseudo‐first order reaction kinetics. Moreover, the rate constant of mineralization was found to be proportional to T_iO₂ film area and the square root of UV light intensity. These results implied the mineralization efficiency of carbofuran could be improved through increasing T_iO₂ film area and UV light intensity. Accordingly, this novel device showed potential application for degrading xenobiotics in water.     

Photocatalytic mineralization of glyphosate in a small-scale plug flow simulation reactor by UV/TiO2

The present work involves the photocatalytic mineralization of glyphosate on a plug flow reactor by UV/TiO₂. The effect of catalyst loading shows an optimal value (0.4 g L^?1) which is necessary to mineralize glyphosate. The kinetic rate of glyphosate mineralization decreases with the increasing initial concentration of glyphosate, and the data can be described using the first-order model. An alkaline environment is conducive to glyphosate mineralization. The mineralization efficiency increases with elevated flow rate to 114 mL min^?1, which is followed by a decrease with a further increase in flow rate due to the reduction of the residence time. The presence of external oxidants (K₂S₂O₈, H₂O₂ and KBrO₃) and photosencitizer (humic acid) can significantly enhance glyphosate mineralization. Photocatalysis oxidation ability of the three studied oxidants decrease in the order of: S₂O₈ ^2? > BrO₃ ^? > H₂O₂. Finally, the Langmuir–Hinshelwood (L-H) model was used to rationalize the mechanisms of reactions occurring on TiO₂ surfaces and L-H model constants were also determined.     

TiO2/Ni PECO体系降解DMP的动力学和光电协同作用研究

以采用微波辅助法制备的TiO₂/Ni光电极为阳极，纤维状石墨毡材料(graphite felt,GF)为阴极，饱和甘汞电极(saturated calomel electrode, SCE)为参比电极建立TiO₂/Ni 光电催化氧化（PECO）体系。以邻苯二甲酸二甲酯（dimethy phthalate,DMP）为目标物，研究其光电催化降解反应动力学和光电协同作用。结果显示：DMP的降解符合拟一级动力学规律；当DMP初始浓度一定时，影响DMP光电催化降解速率的因素由强到弱依次为：催化剂有效面积，紫外光强度，曝氧速率，外加偏转电压等。实验证明本体系中光电之间具有协同作用。     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Photocatalytic degradation of the herbicide pendimethalin using nanoparticles of BaTiO3/TiO2 prepared by gel to crystalline conversion method: A kinetic approach

Photocatalytic degradation of the herbicide, pendimethalin (PM) was investigated with BaTiO₃/TiO₂ UV light system in the presence of peroxide and persulphate species in aqueous medium. The nanoparticles of BaTiO₃ and TiO₂ were obtained by gel to crystallite conversion method. These photo catalysts are characterized by energy dispersive x-ray analysis (EDX), scanning electron microscope (SEM), x-ray diffraction (XRD), and Brunauer-Emmett-Teller (BET) adsorption isotherm and reflectance spectral studies. The quantum yields for TiO₂ and BaTiO₃ for the degradation reactions are 3.166 Einstein m^?2 s^?1 and 2.729 Einstein m^?2 s^?1 and catalytic efficiencies are 6.0444 × 10^?7 mg^?2h^?1L² and 5.403 × 10^?7 mg^?2h^?1L², respectively as calculated from experimental results. BaTiO₃ exhibited comparable photocatalytic efficiency in the degradation of pendimethalin as the most widely used TiO₂ photocatalyst. The persulphate played an important role in enhancing the rate of degradation of pendimethalin when compared to hydrogen peroxide. The degradation process of pendimethalin followed the first-order kinetics and it is in agreement with Langmuir-Hinshelwood model of surface mechanism. The reason for high stability of pendimethalin for UV-degradation even in the presence of catalyst and oxidizing agents were explored. The higher rate of degradation was observed in alkaline medium at pH 11. The degradation process was monitored by spectroscopic techniques such as ultra violet-visible (UV-Vis), infrared (IR) and gas chromatography mass spectroscopy (GC-MS). The major intermediate products identified were: N-propyl-2-nitro-6-amino-3, 4-xylidine, (2, 3-dimethyl-5-nitro-6-hydroxy amine) phenol and N-Propyl-3, 4-dimethyl-2, 6-dinitroaniline by GC-MS analysis and the probable reaction mechanism has been proposed based on these products.     

Ru-TiO_2光电极对亚甲基蓝的光电催化降解

采用阳极氧化法制备Ru-TiO2光电极,以该电极为工作电极,石墨作对电极,饱和甘汞电极为参比电极,对亚甲基蓝溶液的光电催化降解进行了研究。结果表明:煅烧温度600℃,掺杂1%Ru的Ru-TiO2光电极催化活性最好;以紫外灯(125 W)为光源,当外加偏压0.2 V,pH为5时,Ru-TiO2光电催化亚甲基蓝120 min可使其完全脱色;亚甲基蓝的光电催化降解遵从Langmuir-Hinshelwood动力学模型,测得其反应速率常数k=0.781 mmol/(L.min),吸附常数K=0.225 L/mmol。     

Photocatalytic decomposition of crotamiton over aqueous TiO(2) suspensions: determination of intermediates and the reaction pathway

The photocatalytic degradation of crotamiton in aqueous solution using TiO₂ was investigated. To investigate the effect of initial pH, the photodegradation behaviors of three types of pharmaceuticals were compared (crotamiton, clofibric acid, sulfamethoxazole). The degradation rates of crotamiton in the pH range 3-9 were nearly equal, but those of clofibric acid and sulfamethoxazole were affected by pH. At pH > 6.5, TiO₂ particles, clofibric acid and sulfamethoxazole had negative charge, therefore, the repulsive force between TiO₂ particles and anionic pharmaceuticals occurred and a low reaction rate at high pH was observed. The effect of UV intensity and TiO₂ concentration on photodegradation efficiency was also investigated. Linear and logarithmical relationships between UV intensity, TiO₂ concentration and the reaction rate constant were confirmed. Furthermore, the structures of photodegradation intermediates formed concomitantly with the disappearance of crotamiton were estimated. Seven intermediates were characterized by LC/MS/MS analyses, and it was assumed that the photocatalytic degradation of crotamiton was initiated by the attack of electrophilic hydroxyl radicals on aromatic rings and alkyl chains.     

Degradation of bisphenol A by the UV/H2O2 process: a kinetic study

A theoretical and experimental study of bisphenol A (BPA) degradation by the UV/H₂O₂ process in water is presented. The effects of the H₂O₂ concentration and the specific rate of photon emission (E_P,0) on BPA degradation were investigated. A kinetic model derived from a reaction sequence was employed to predict BPA and hydrogen peroxide concentrations over time using an annular photochemical reactor in batch recirculation mode. The local volumetric rate of photon absorption (LVRPA) inside the photoreactor was computed using a Line Source with Parallel Plane emission model (LSPP). From the proposed kinetic model and the experimental data, the second order rate constants of the reactions between hydroxyl radicals and the main reacting species (H₂O₂ and BPA) were estimated applying a nonlinear regression method. A good agreement between the kinetic model and experimental data, for a wide range of operating conditions, was obtained. For BPA, H₂O₂, and TOC concentrations, the calculated root means square errors (RMSE) were 2.3?×?10^??2, 9.8?×?10^??1, and 9.0?×?10^??2 mmol L^??1, respectively. The simplified kinetic model presented in this work can be directly applied to scaling-up and reactor design, since the estimated kinetic constants are independent of the reactor size, shape, and configuration. Further experiments were made by employing low BPA initial concentration (100 μg L^??1) in water and real wastewater. A lower degradation rate of BPA was observed in the real wastewater, although the UV/H₂O₂ process has also been able to completely degrade the target pollutant in less than 1 h.

     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La₂O₃(0.5%)-ZnO(20%)-TiO₂/沸石复合光催化剂，以20 W紫外灯为光源，在自制的光催化反应器中降解活性艳红K-2BP，考察了光照时间、空气通入量、催化剂用量、溶液初始浓度、H₂O₂与Fe³⁺投加量等对活性艳红K-2BP光催化降解率的影响。结果表明，当溶液初始浓度为60 mg/L，催化剂投加量为12 g/L，通气量为1 200 mL/min，光照2.5 h，活性艳红K-2BP的降解率可达99.2%；H₂O₂和Fe³⁺投加量为4 mL/L和3 g/L时，光照1 h活性艳红K-2BP降解率分别为100%和97.2%。紫外可见吸收光谱显示，LZTZ光催化剂可有效降解印染废水。     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料，空心微珠为载体，采用溶胶凝胶法制备TiO₂/beads光催化剂载体，然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂，并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性，考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明，在中性条件下，H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L，浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

Synthetic TiO2 nanoparticle emission from exterior facades into the aquatic environment

We present direct evidence of the release of synthetic nanoparticles from urban applications into the aquatic environment. We investigated TiO₂ particles as these particles are used in large quantities in exterior paints as whitening pigments and are to some extent also present in the nano-size range.TiO₂ particles were traced from exterior facade paints to the discharge into surface waters. We used a centrifugation based sample preparation which recovers TiO₂ particles between roughly 20 and 300 nm. Analytical electron microscopy revealed that TiO₂ particles are detached from new and aged facade paints by natural weather conditions and are then transported by facade runoff and are discharged into natural, receiving waters. Microscopic investigations are confirmed by bulk chemical analysis. By combining results from microscopic investigations with bulk chemical analysis we calculated the number densities of synthetic TiO₂ particles in the runoff.     

纯二氧化碳条件下小球藻固定CO2

微藻固碳已经成为消减温室气体排放的新的研究热点。利用静态吸收方法，考查了通人纯CO2对普通小球藻生长特点、固定CO2效率以及藻液pH值变异的影响。结果表明：通入纯CO2使小球藻生长延滞期显著延长，比普通培养延长10～12d，对其他生长阶段的影响不大；小球藻固定CO2速率可分为2个过程，即物理固碳过程和生物固碳过程，前者在藻细胞延滞期发生，峰值由CO。溶解于培养液造成，后者在藻细胞生长的指数期、稳定期和衰退期发生，峰值由藻细胞指数生长造成，2个过程中，固定CO2速率的变化趋势都是先增大后降低；纯CO2条件下，藻液pH值变化速率高，4d内，藻液即被酸化，随后藻液pH值变化速率逐渐降低，且pH值稳定在适宜水平。因此，采用小球藻固定高浓度CO2时，建议提高接种量并加强培养前期的pH值监测和调控，以保证藻液保持适宜的pH值，并缩短培养时间，提高生物固碳效率。     

银钛共负载型光催化材料降解甲基橙废水简

以膨胀珍珠岩为载体，采用溶胶凝胶法对其进行负载，制备出不同类型的光催化材料（TiO₂-EP、Ag⁺-TiO₂-EP），并在模拟日光条件下，研究其对甲基橙溶液的降解效果。结果表明，浸渍3次且担载0.04% Ag⁺的负载型TiO₂光催化活性最高，在光催化剂用量为0.3 g，20 mL初始浓度为10 mg/L甲基橙溶液光照4 h后降解率可达81.6%，且甲基橙的光催化降解服从一级动力学方程。回收3次后仍有较强的活性，其2 h降解率为24.8%。     

微波辐射Bi2O3/沸石-H2O2体系降解废水中的硝基苯

研究了微波辐射下，以负载于沸石上的三氧化二铋为催化剂，以双氧水为氧化剂的催化氧化体系处理硝基苯工艺。通过单因素实验法，从反应催化剂负载量、pH、双氧水用量、微波功率、反应时间、催化剂用量等方面初步考察了硝基苯在该体系中的催化氧化效果。在氧化铋负载量3%（质量比），pH=2，2 mL 30%双氧水，火力为中火，催化剂投加量为0.7 g，反应2 min，对降解过程所得的中间产物和终产物进行了分析。结果表明，该体系对硝基苯的去除率能够达到99.2%，COD去除率为73.91%。