Photocatalytic oxidation of xenobiotics in water with immobilized TiO2 on agitator

A novel photocatalytic oxidation reactor, using Degussa P-25 TiO2 as a stationary phase with a thickness of 1.5-2.0 um on the blades of agitator, was developed to study the photocatalytic oxidation of xenobiotics. Particularly in this device, separation of photocatalyst from the purified water after oxidation reaction was not necessary, and no other aeration equipment was required to supply oxygen. To examine the efficiency of this device, photocatalytic degradation of xenobiotic organics such as carbofuran was studied as an example. Results indicated that carbofuran could be degraded completely with mineralization efficiency of 20% after 6 hours of oxidation under the imposed conditions. The mineralization rate of carbofuran was found to follow the pseudo-first order reaction kinetics. Moreover, the rate constant of mineralization was found to be proportional to TiO2 film area and the square root of UV light intensity. These results implied the mineralization efficiency of carbofuran could be improved through increasing TiO2 film area and UV light intensity. Accordingly, this novel device showed potential application for degrading xenobiotics in water.     

Photocatalytic Degradation of an Organophosphorus Pesticide Phosalone in Aqueous Suspensions of Titanium Dioxide

Abstract

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO₂ particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. The half-life (DT₅₀) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K = 0.0532 min^?1). The half-life time of photomineralization in the concentration range of 7.5–20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Photocatalytic Degradation of the Herbicide Erioglaucine in the Presence of Nanosized Titanium Dioxide: Comparison and Modeling of Reaction Kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO₂ nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO₂ and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO₂, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO₂ system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir–Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm^{? 1} and 0.984 ppm min^{? 1}, respectively. In this work, we also compared the reactivity between the commercial TiO₂ Degussa P-25 and a rutile TiO₂. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO₂ for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO₂ process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO₂.     

Photocatalytic mineralization of glyphosate in a small-scale plug flow simulation reactor by UV/TiO2

The present work involves the photocatalytic mineralization of glyphosate on a plug flow reactor by UV/TiO₂. The effect of catalyst loading shows an optimal value (0.4 g L^?1) which is necessary to mineralize glyphosate. The kinetic rate of glyphosate mineralization decreases with the increasing initial concentration of glyphosate, and the data can be described using the first-order model. An alkaline environment is conducive to glyphosate mineralization. The mineralization efficiency increases with elevated flow rate to 114 mL min^?1, which is followed by a decrease with a further increase in flow rate due to the reduction of the residence time. The presence of external oxidants (K₂S₂O₈, H₂O₂ and KBrO₃) and photosencitizer (humic acid) can significantly enhance glyphosate mineralization. Photocatalysis oxidation ability of the three studied oxidants decrease in the order of: S₂O₈ ^2? > BrO₃ ^? > H₂O₂. Finally, the Langmuir–Hinshelwood (L-H) model was used to rationalize the mechanisms of reactions occurring on TiO₂ surfaces and L-H model constants were also determined.     

Degradation of Carbofuran in Water by Solar Photocatalysis in Presence of Photosensitizers

The effect of the presence of photosensitizers, methylene blue (MB) and rose Bengal (RB), on the degradation of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) in water in a solar photocatalytic system was investigated. It was found that as compared to MB, RB generally showed a stronger effect on the decomposition of carbofuran under comparable conditions. Among the conditions studied, adding 2 × 10^?6 M of RB, that corresponding to 2% of the initial concentration of carbofuran solution in the system, rendered the most effective degradation of carbofuran. As a result, a carbofuran removal percentage of 69.9%, a mineralization efficiency of 28.0%, and a microtoxicity reduction of 65.0% could be achieved. The degradation and mineralization of carbofuran was found to follow the pseudo-first order reaction kinetics. The decomposition mechanism of carbofuran was further investigated through identification of the intermediates to elaborate the influence of dye photosensitizer on the solar photocatalysis of carbofuran in water. On the basis of the intermediates identified, including carbofuran phenol, 3-hydroxy carbofuran phenol, and substituted alcohols (3-phenoxy 1-propanol, 2-ethyl 1-hexanol, 2-butoxyl ethanol), it appears that hydrolysis and hydroxylation were the two key mechanisms for decomposing carbofuran during the process of solar photocatalysis with the aid of dye photosensitizer.     

Photocatalytic removal of organic pollutants in aqueous solution by Bi(4)Nb(x)Ta((1-x))O(8)I

In this work, Bi₄Nb_xTa_(1−x)O₈I photocatalysts have been synthesized by solid state reaction method and characterized by powder X-ray diffraction, scanning electron microscope and UV-Vis near infrared diffuse reflectance spectroscopy. The photocatalytic activity of these photocatalysts was evaluated by the degradation of methyl orange (MO) in aqueous solutions under visible light, UV light and solar irradiation. The effects of catalyst dosage, initial pH and MO concentration on the removal efficiency were studied, and the photocatalytic reaction kinetics of MO degradation as well. The results indicated that Bi₄Nb_xTa_(1−x)O₈I exhibited high photocatalytic activity for the removal of MO in aqueous solutions. For example, the removal efficiency of MO by Bi₄Nb_0.1Ta_0.9O₈I was as high as 92% within 12 h visible light irradiation under the optimal conditions: initial MO concentration of 5-10 mg L⁻¹, catalyst dosage of 6 g L⁻¹ and natural pH (6-8), the MO molecules could be completely degradated by Bi₄Nb_0.1Ta_0.9O₈I within 40 min under UV light irradiation, and the photodegradation efficiency reaches to 60% after 7 h solar irradiation. Furthermore, the photocatalytic degradation of Bisphenol A (BPA) was also investigated under visible light irradiation. It is found that 99% BPA could be mineralized by Bi₄Nb_0.1Ta_0.9O₈I after 16 h visible light irradiation. Through HPLC/MS, BOD, TOC, UV-Vis measurements, we determined possible degradation products of MO and BPA. The results indicated that MO was degradated into products which are easier to be biodegradable and innocuous treated, and BPA could be mineralized completely. Furthermore, the possibility for the photosensitization effect in the degradation process of MO under visible light irradiation has been excluded.     

H4SiW12O40/TiO2/beads光催化降解亚甲基蓝的研究

以钛酸四丁酯为原料，空心微珠为载体，采用溶胶凝胶法制备TiO₂/beads光催化剂载体，然后浸渍法制备出H₄SiW₁₂O₄₀/TiO₂/beads表面负载修饰型复合光催化剂，并运用SEM、XRD、FT-IR和DRS对催化剂进行表征和分析。研究了H₄SiW₁₂O₄₀/TiO₂/beads对亚甲基蓝降解的光催化活性，考察了光强度、pH值、曝气量、底物浓度和催化剂用量等对催化效率的影响。实验结果表明，在中性条件下，H₄SiW₁₂O₄₀/TiO₂/beads催化剂的投加量为0.25 g/L，浓度为7.5 mg/L的亚甲基蓝溶液在250 W的紫外灯和600 W的可见光灯下光照60 min降解率分别可达到94.5%和55%。     

CdS-TiO_2/MWCNTs结构表征及其光催化性能

采用溶胶-凝胶法,制备了多壁碳纳米管(MWCNTs)负载的双组分复合半导体光催化剂CdS-TiO2/MWCNTs。通过透射电镜(TEM)、比表面分析(BET)、X射线衍射(XRD)和紫外-可见吸收光谱(UV-vis)等分析方法对光催化剂进行了结构表征,并考察了CdS-TiO2/MWCNTs对甲苯降解的光催化性能。结果表明:纳米活性粒子CdS-TiO2均匀负载于MWCNTs上,比表面积、光吸收阈值和强度增大,活性粒子间以及活性粒子与载体之间具有协同作用,有利于光催化性能的提高,CdS-TiO2/MWCNTs在主波长为254 nm紫外光照射下对甲苯的降解效果较好,去除率可达55.3%。     

Photocatalytic degradation of p,p′-DDT under UV and visible light using interstitial N-doped TiO2

1,1,1-trichloro-2,2-bis(p-chlorophenyl)ethane (or p,p′-DDT) is one of the most persistent pesticides. It is resistant to breakdown in nature and cause the water contamination problem. In this work, a major objective was to demonstrate the application of N-doped TiO₂ in degradation and mineralization of the p,p′-DDT under UV and visible light in aqueous solution. The N-doped TiO₂ nanopowders were prepared by a simple modified sol–gel procedure using diethanolamine (DEA) as a nitrogen source. The catalyst characteristics were investigated using XRD, SEM, TEM, and XPS. The adsorption and photocatalytic oxidation of p,p′-DDT using the synthesized N-doped TiO₂ under UV and visible light were conducted in a batch photocatalytic experiment. The kinetics and p,p′-DDT degradation performance of the N-doped TiO₂ were evaluated. Results show that the N-doped TiO₂ can degrade p,p′-DDT effectively under both UV and visible lights. The rate constant of the p,p′-DDT degradation under UV light was only 0.0121 min^?1, whereas the rate constant of the p,p′-DDT degradation under visible light was 0.1282 min^?1. Under visible light, the 100% degradation of p,p′-DDT were obtained from N-doped TiO₂ catalyst. The reaction rate of p,p′-DDT degradation using N-doped TiO₂ under visible light was sixfold higher than that under UV light. According to Langmuir-Hinshelwood model, the adsorption equilibrium constant (K) for the N-doped TiO₂ under visible light was 0.03078 L mg^?1, and the apparent reaction rate constant (k) was 1.3941 mg L^?1-min. Major intermediates detected during the p,p′-DDT degradation were p,p′-DDE, o,p′-DDE, p,p′-DDD and p,p′-DDD. Results from this work can be applied further for the breakdown of p,p′-DDT molecule in the real contaminated water using this technology.     

Removal of AOX, total nitrogen and chlorinated lignin from bleached Kraft mill effluents by UV oxidation in the presence of hydrogen peroxide utilizing TiO2 as photocatalyst

Background, aim, and scope  The pulp and paper industry is the sixth largest polluter discharging a variety of gaseous, liquid, and solid wastes into the environment. Effluents from bleached Kraft mill effluents (BKME) are polluting waters to a great extent These effluents cause considerable damage to the receiving waters if discharged untreated since they have high levels of biological oxygen demand (BOD), chemical oxygen demand (COD), chlorinated compounds (measured as AOX), suspended solids (mainly fibers), fatty acids, tannins, resin acids, lignin and its derivatives, sulfur and sulfur compounds, etc. This study aimed to remove adsorbed organic halogen (AOX), total nitrogen, and lignin-degrading products in the wastewater (4,500 m³/h) from the paper mill in the pulp and paper industry, which is discharged to sea from a plant located in western Turkey. Materials and methods  The photocatalytic degradation of AOX, total nitrogen, and chlorinated lignin in BKME have been investigated in different parameters, such as time, H₂O₂ and TiO₂ concentration. In addition, for investigating the effect of chlorine on the removal of lignin, pure lignin solution was prepared in equal amounts to chlorinated lignin degradation products found in BKME. The same experiments were conducted for this solution. Experiments were carried out in photocatalytic reactor made of Pyrex glass. The mercury lamp was used as a radiation source. All irradiation was carried out under constant stirring. The existence of dissolved O₂ is an important factor which increases the photocatalytic degradation. Hence, we used an air pump for the aeration of the wastewater solutions. The temperature of the wastewater was controlled and adjusted to 25°C by thermostat pump in conjunction with a cooler. At the end of all experiments, AOX, total nitrogen and lignin concentrations were analyzed according to standard methods. All experiments were performed in duplicate and average values were used. Results and discussion  When the effect of H₂O₂ and time were investigated, it was observed that the AOX concentration increased from 3.0 to 11.0 mg/L by only UV. However, when H₂O₂ was added, AOX concentration decreased from approximately 3.0 to 0.0 mg/L. The optimal conditions for the removal of AOX appear to be an initial H₂O₂ concentration of 20.0 mL/L and reaction time of 50 min. In addition, at the same experiment conditions, it was seen that the total nitrogen concentration decreased from 23.0 to 15.0 mg/L by only UV and by increasing H₂O₂ concentration, the concentration of 20.0 mL/L H₂O₂ appears to be optimal (9.0 mg/L). The AOX, total nitrogen and lignin degradation products and pure lignin go through a minimum when the concentration of H₂O₂ and TiO₂ increases at constant pH and UV intensity. The kinetics for the degradation of AOX, total nitrogen and lignin degradation products followed a pseudo-first order law with respect to the products, and the degradation rates (min⁻¹) for the UV/TiO₂/H₂O₂ system were higher than that of the corresponding values for the UV/H₂O₂ system. Conclusions  The AOX, total nitrogen and lignin concentration go through a minimum when the concentration of H₂O₂ and TiO₂ increases at constant pH and UV intensity. It was found that the UV/TiO₂/H₂O₂ system has proved capable of the degradation of total nitrogen as well as chlorinated and degraded lignin in BKME. Recommendations and perspectives  The photocatalytic process can be considered a suitable alternative for the remove of some compounds from the BKME. Nevertheless, further studies should be carried out to confirm the practical feasibility of BKME. Another result obtained from the study is that pre-purification carried out with UV/TiO₂/H₂O₂ photocatalytic process may constitute an important step for further purification processes such as adsorption, membrane processes, etc.     

组合方法去除新型采油污水中有机污染物的研究

含聚丙烯酰胺采油污水的有效处理是近年来困扰油田三次采油生产的一个难题。研究采用移动床生物膜技术与O3/UV/H2O2高级氧化技术的组合方法来处理含聚丙烯酰胺采油污水。实验结果表明,移动床生物膜技术可以有效去除污水中的石油类有机物,但对聚丙烯酰胺几乎无效果。O3/UV/H2O2高级氧化技术可以降解污水中的聚丙烯酰胺。组合方法处理后的含聚丙烯酰胺采油污水水质可以达到污水综合排放标准中的一级要求。     

Photooxidative removal of the herbicide Acid Blue 9 in the presence of hydrogen peroxide: modeling of the reaction for evaluation of electrical energy per order (EEO)

The present work deals with photooxidative removal of the herbicide, Acid Blue 9 (AB9), in water in the presence of hydrogen peroxide (H₂O₂) under UV light illumination (30 W). The influence of the basic operational parameters such as amount of H₂O₂, irradiation time and initial concentration of AB9 on the photodegradation efficiency of the herbicide was investigated. The degradation rate of AB9 was not appreciably high when the photolysis was carried out in the absence of H₂O₂ and it was negligible in the absence of UV light. The photooxidative removal of the herbicide was found to follow pseudo-first-order kinetic, and hence the figure-of-merit electrical energy per order (E_Eo) was considered appropriate for estimating the electrical energy efficiency. A mathematical relation between the apparent reaction rate constant and H₂O₂ used was applied for prediction of the electricity consumption in the photooxidative removal of AB9. The results indicated that this kinetic model, based on the initial rates of degradation, provided good prediction of the E_Eo values for a variety of conditions. The results also indicated that the UV/H₂O₂ process was appropriate as the effective treatment method for removal of AB9 from the contaminated wastewater.     

Carbofuran degraded by iron-doped anatase: Weakening the cholinesterase inhibitory activity in the photoproducts mixture

Carbofuran is a toxic carbamate pesticide, and its use has increased in recent years. While marketing information indicates stability in different chemical media, carbofuran exhibits relative photolability. The aim of this research was to decompose carbofuran and to identify the photoproducts achieved when two different doped titania photocatalysts were employed under UV irradiation. The iron-doped TiO₂ materials were obtained (a) via a hydrothermal method and (b) by an ultrasound-assisted sol–gel method. The precursors were TiOSO₄?xH₂O and Fe₃(NO₃)·9H₂O. X-ray studies confirmed that the anatase phase of the iron-doped TiO₂ resulted from the two preparation methods. The photocatalytic performance of the prepared materials was monitored by LC/ESI-QTOF-MS, enabling the identification of photoproducts: oxo-carbamates, hydroxylated benzofuranes, a carboxamide, and one amine. By using the iron-doped TiO₂ materials, 2,2-dimethyl-2,3-dihydrobenzofuran-3,7-diol was the most abundant photoproduct, and N,2,2-trimethyl-2,3-dihydrobenzofuran-7-amine was the only compound that had not been previously reported in the photolysis and photocatalysis of carbofuran. The product 3-hydroxy carbofuran, a cholinesterase inhibitor, was quantified and was found to be transformed into compounds that lack this inhibitive property.     

Solar photocatalytic decolorization of methylene blue in water

In this study, a photocatalytic decolorization system equipped with immobilized TiO2 and illuminated by solar light was used to remove the color of wastewater. To examine the decoloring efficiency of this system, photocatalytic decolorization of an organic dye such as methylene blue was studied as an example. The effects of light source, pH, as well as the initial concentration of dye were also investigated. It was observed that the solution of methylene blue could be almost completely decolorized by the solar light/TiO2 film process while there was about 50% color remaining with solar irradiation only. In addition, it was found that the decoloring efficiency of solution was higher with solar light irradiation than with artificial UV light irradiation, even though the artificial UV light source supplied higher UV intensity at 254 nm. The color removal rate of methylene blue with solar light irradiation was almost twice that of artificial UV light irradiation. This phenomena was mainly attributed to that some visible light range of solar light was useful for exciting the methylene blue molecules adsorbed on TiO2 film, leading to a photosensitization process undergoing and decoloring efficiency promoted. This solar-assisted photocatalytic device showed potential application for decoloring organic dyes in wastewater.     

Photocatalytic decomposition of crotamiton over aqueous TiO(2) suspensions: determination of intermediates and the reaction pathway

The photocatalytic degradation of crotamiton in aqueous solution using TiO₂ was investigated. To investigate the effect of initial pH, the photodegradation behaviors of three types of pharmaceuticals were compared (crotamiton, clofibric acid, sulfamethoxazole). The degradation rates of crotamiton in the pH range 3-9 were nearly equal, but those of clofibric acid and sulfamethoxazole were affected by pH. At pH > 6.5, TiO₂ particles, clofibric acid and sulfamethoxazole had negative charge, therefore, the repulsive force between TiO₂ particles and anionic pharmaceuticals occurred and a low reaction rate at high pH was observed. The effect of UV intensity and TiO₂ concentration on photodegradation efficiency was also investigated. Linear and logarithmical relationships between UV intensity, TiO₂ concentration and the reaction rate constant were confirmed. Furthermore, the structures of photodegradation intermediates formed concomitantly with the disappearance of crotamiton were estimated. Seven intermediates were characterized by LC/MS/MS analyses, and it was assumed that the photocatalytic degradation of crotamiton was initiated by the attack of electrophilic hydroxyl radicals on aromatic rings and alkyl chains.     

Performance evaluation of the UV/H2O2 process on selected nitrogenous organic compounds: reductions of organic contents vs. corresponding C-, N-DBPs formations

The presence of various organic contaminants in water sources is of concern due to their direct threats to human health and potential to react with disinfectants to form carcinogenic byproducts including trihalomethanes, haloacetic acids and nitrosamines in finished water. This study applied both medium-pressure and low-pressure ultraviolet light coupled with hydrogen peroxide (UV/H₂O₂) to evaluate its efficacy for degradation of selected nitrogenous organic compounds and corresponding disinfection byproduct (DBP) formation. Six organic compounds were chosen as target precursors based on their nitrogen contents and molecular structures. The results showed that higher oxidation capacity resulted in better reduction of organic matters and DBP formation potentials (DBPFPs). However, insufficient contact time and oxidant doses could lead to a rise of DBPFPs in the early stages of UV/H₂O₂ reactions. A greater percentage removal was achieved for organic carbon than organic nitrogen after UV/H₂O₂ treatment, especially for compounds with complicated structure such as diltiazem. During the UV/H₂O₂ treatment, the intermediate products include tertiary amine, dimethyl amine (DMA) or DMA-like structures, which are N-nitrosodimethylamine (NDMA) precursors after chlorination or chloramination. Furthermore, it was observed that using dissolved organic nitrogen and DMA to predict NDMAFP could lead to biased conclusions because of the complex nature of nitrogenous matters in aqueous environments.     

Photocatalytic degradation of gaseous toluene over Ag-doping TiO₂ nanotube powder prepared by anodization coupled with impregnation method

In this work, Ag-doping TiO₂ nanotubes were prepared and employed as the photocatalyst for the degradation of toluene. The TiO₂ nanotube powder was produced by the rapid-breakdown potentiostatic anodization of Ti foil in chloride-containing electrolytes, and then doped with Ag through an incipient wetness impregnation method. The samples were characterized by scanning electron microscope, high-resolution transmission electron microscopy, X-ray diffraction, surface photovoltage measurements, X-ray photoelectron spectroscopy and N₂ adsorption. The nanotubular TiO₂ photocatalysts showed an outer diameter of approximately 40 nm, fine mesoporous structure and high specific surface area. The photocatalytic activity of Ag-doping TiO₂ nanotube powder was evaluated through photooxidation of gaseous toluene. The results indicated that the degradation efficiency of toluene could get 98% after 4 h reaction using the Ag-doping TiO₂ nanotubes as the photocatalyst under UV light illumination, which was higher than that of the pure TiO₂ nanotubes, Ag-doping P25 or P25. Benzaldehyde species could be observed during the photocatalytic oxidation monitored by in situ FTIR, and the formed benzaldehyde intermediate during reaction would be partially oxidized into CO₂ and H₂O.     

TiO2膜降解水中污染物的稳定性考察与再生方法研究

针对实际水处理中对催化剂性能的要求，以光催化降解苯酚溶液作为探针反应，考察了玻璃纤维网上负载的TiO₂膜催化剂长期使用条件下的稳定性，研究了催化剂在自来水中使用失活后的再生方法。结果表明，经过50次使用之后，膜催化剂120 min反应对苯酚的降解率从100%下降至83%，总体上看，所制催化剂还是具有相当好的稳定性；在反应器中用蒸馏水浸泡配合光催化反应对TiO₂膜催化剂进行原位再生是一种可行的再生途径。     

Degradation of ethylenethiourea pesticide metabolite from water by photocatalytic processes

In this study, photocatalytic (photo-Fenton and H₂O₂/UV) and dark Fenton processes were used to remove ethylenethiourea (ETU) from water. The experiments were conducted in a photo-reactor with an 80 W mercury vapor lamp. The mineralization of ETU was determined by total organic carbon analysis, and ETU degradation was qualitatively monitored by the reduction of UV absorbance at 232 nm. A higher mineralization efficiency was obtained by using the photo-peroxidation process (UV/H₂O₂). Approximately 77% of ETU was mineralized within 120 min of the reaction using [H₂O₂]₀ = 400 mg L^?1. The photo-Fenton process mineralized 70% of the ETU with [H₂O₂]₀ = 800 mg L^?1 and [Fe²⁺] = 400 mg L^?1, and there is evidence that hydrogen peroxide was the limiting reagent in the reaction because it was rapidly consumed. Moreover, increasing the concentration of H₂O₂ from 800 mg L^?1 to 1200 mg L^?1 did not enhance the degradation of ETU. Kinetics studies revealed that the pseudo-second-order model best fit the experimental conditions. The k values for the UV/H₂O₂ and photo-Fenton processes were determined to be 6.2 × 10^?4 mg L^?1 min^?1 and 7.7 × 10^?4 mg L^?1 min^?1, respectively. The mineralization of ETU in the absence of hydrogen peroxide has led to the conclusion that ETU transformation products are susceptible to photolysis by UV light. These are promising results for further research. The processes that were investigated can be used to remove pesticide metabolites from drinking water sources and wastewater in developing countries.     

颜料红254-TiO_2光催化降解罗丹明B废水

以工业有机颜料C.I.颜料红254(DPP254)为敏化剂,通过溶剂热法对纯TiO2进行改性,得到复合光催化剂DPP254-TiO2。并通过XRD、SEM、UV-Vis DRS和N2吸附-脱附(BET和BJH)等测试手段对DPP254-TiO2进行了表征。以罗丹明B(RhB)为目标降解物,研究了DPP254-TiO2在可见光下对有机污染物的光催化降解性能。同时考察了DPP254含量、反应时间、RhB初始浓度和催化剂浓度等因素对RhB降解速率的影响。结果表明,改性后的催化剂光响应范围由紫外光区拓宽到可见光区。对其光催化反应机理进行了探讨。催化剂重复使用4次,活性没有明显降低,说明催化剂具有很好的稳定性。