Photocatalytic oxidation of xenobiotics in water with immobilized TIO2 on agitator

Abstract

A novel photocatalytic oxidation reactor, using Degussa P‐25 T_iO₂ as a stationary phase with a thickness of 1.5–2.0 um on the blades of agitator, was developed to study the photocatalytic oxidation of xenobiotics. Particularly in this device, separation of photocatalyst from the purified water after oxidation reaction was not necessary, and no other aeration equipment was required to supply oxygen. To examine the efficiency of this device, photocatalytic degradation of xenobiotic organics such as carbofuran was studied as an example. Results indicated that carbofuran could be degraded completely with mineralization efficiency of 20 % after 6 hours of oxidation under the imposed conditions. The mineralization rate of carbofuran was found to follow the pseudo‐first order reaction kinetics. Moreover, the rate constant of mineralization was found to be proportional to T_iO₂ film area and the square root of UV light intensity. These results implied the mineralization efficiency of carbofuran could be improved through increasing T_iO₂ film area and UV light intensity. Accordingly, this novel device showed potential application for degrading xenobiotics in water.     

Solar photocatalytic decolorization of methylene blue in water

In this study, a photocatalytic decolorization system equipped with immobilized TiO2 and illuminated by solar light was used to remove the color of wastewater. To examine the decoloring efficiency of this system, photocatalytic decolorization of an organic dye such as methylene blue was studied as an example. The effects of light source, pH, as well as the initial concentration of dye were also investigated. It was observed that the solution of methylene blue could be almost completely decolorized by the solar light/TiO2 film process while there was about 50% color remaining with solar irradiation only. In addition, it was found that the decoloring efficiency of solution was higher with solar light irradiation than with artificial UV light irradiation, even though the artificial UV light source supplied higher UV intensity at 254 nm. The color removal rate of methylene blue with solar light irradiation was almost twice that of artificial UV light irradiation. This phenomena was mainly attributed to that some visible light range of solar light was useful for exciting the methylene blue molecules adsorbed on TiO2 film, leading to a photosensitization process undergoing and decoloring efficiency promoted. This solar-assisted photocatalytic device showed potential application for decoloring organic dyes in wastewater.     

Photocatalytic oxidation of pesticide rinsate

Pesticide rinsate has been considered as one of the major threats for the environment. In this study, photocatalysts such as TiO2 and O3 were used to promote the efficiency of direct UV photolysis to prevent such wastewater pollution. Carbofuran (a carbamate pesticide) and mevinphos (an organophosphate pesticide) with a concentration of 100 mg/L were selected as the test pesticide rinsates. Parent pesticide compound, COD, and microtoxicity analysis were employed to investigate the effect of photocatalyst on the degradation efficiency of pesticide in rinsate. It was found that the photocatalytic oxidation process (UV/O3, UV/TiO2) showed much higher COD removal and microtoxicity reduction efficiency for pesticide rinsate than did direct UV photolysis under the imposed conditions, suggesting that photocatalytic oxidation processes such as UV/O3 and UV/TiO2 could be a better alternative to treat pesticide rinsate. In addition, it was noted that increasing the initial pH of mevinphos rinsate to a basic level was required to reach higher COD removal efficiency and positive microtoxicity reduction efficiency while it was not necessary for the treatment of carbofuran rinsate.     

Photocatalytic degradation of the herbicide erioglaucine in the presence of nanosized titanium dioxide: comparison and modeling of reaction kinetics

The present work mainly deals with photocatalytic degradation of a herbicide, erioglaucine, in water in the presence of TiO2 nanoparticles (Degussa P-25) under ultraviolet (UV) light illumination (30 W). The degradation rate of erioglaucine was not so high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. We have studied the influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time and initial concentration of erioglaucine on the photodegradation efficiency of erioglaucine. A kinetic model is applied for the photocatalytic oxidation by the UV/TiO2 system. Experimental results indicated that the photocatalytic degradation process could be explained in terms of the Langmuir-Hinshelwood kinetic model. The values of the adsorption equilibrium constant, K, and the second order kinetic rate constant, k, were 0.116 ppm-1 and 0.984 ppm min-1, respectively. In this work, we also compared the reactivity between the commercial TiO2 Degussa P-25 and a rutile TiO2. The photocatalytic activities of both photocatalysts were tested using the herbicide solution. We have noticed that photodegradation efficiency was different between both of them. The higher photoactivity of Degussa P-25 compared to that of rutile TiO2 for the photodegradation of erioglaucine may be due to higher hydroxyl content, higher surface area, nano-size and crystallinity of the Degussa P-25. Our results also showed that the UV/TiO2 process with Degussa P-25 as photocatalyst was appropriate as the effective treatment method for removal of erioglaucine from a real wastewater. The electrical energy consumption per order of magnitude for photocatalytic degradation of erioglaucine was lower with Degussa P-25 than in the presence of rutile TiO2.     

Photocatalytic reactions of phenanthrene at TiO2/water interfaces

The photocatalytic oxidation of phenanthrene was investigated in aqueous TiO2 suspensions under UV light irradiation. Chemical oxygen demand (COD) measurements, UV-Vis spectrophotometer, IR spectrometer and gas chromatography-mass spectrometry (GC-MS) analytical techniques were used to monitor the reaction process. Some factors affecting the photodegradation rate were studied and some aromatic intermediates were detected during the reaction process. Fast and complete mineralization of phenanthrene was achieved in this reaction system.     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.     

Fresnel lens to concentrate solar energy for the photocatalytic decoloration and mineralization of orange II in aqueous solution

The decoloration and mineralization of the azo dye orange II under conditions of artificial ultraviolet light and solar energy concentrated by a Fresnel lens in the presence of hydrogen peroxide and TiO(2)-P25 was studied. A comparative study to demonstrate the viability of this solar installation was done to establish if the concentration reached in the focus of the Fresnel lens was enough to improve the photocatalytic degradation reaction. The degradation efficiency was higher when the photolysis was carried out under concentrated solar energy irradiation as compared to UV light source in the presence of an electron acceptor such us H(2)O(2) and the catalyst TiO(2). The effect of hydrogen peroxide, pH and catalyst concentration was also determined. The increase of H(2)O(2) concentration until a critical value (14.7 mM) increased both the solar and artificial UV oxidation reaction rate by generating hydroxyl radicals and inhibiting the (e(-)/h(+)) pair recombination, but the excess of hydrogen peroxide decreases the oxidation rate acting as a radical or hole scavenger and reacting with TiO(2) to form peroxo-compounds, contributing to the inhibition of the reaction. The use of the response surface methodology allowed to fit the optimal values of the parameters pH and catalyst concentration leading to the total solar degradation of orange II. The optimal pH range was 4.5-5.5 close to the zero point charge of TiO(2) depending on surface charge of catalyst and dye ionization state. Dosage of catalyst higher than 1.1 gl(-1) decreases the degradation efficiency due to a decrease of light penetration.     

Photocatalytic degradation of an organophosphorus pesticide phosalone in aqueous suspensions of titanium dioxide

The present work deals with photocatalytic degradation of an organophosphorus pesticide, phosalone, in water in the presence of TiO2 particles under UV light illumination (1000 W). The influence of the basic photocatalytic parameters such as pH of the solution, amount of TiO2, irradiation time, stirring rate, and distance from UV source, on the photodegradation efficiency of phosalone was investigated. The degradation rate of phosalone was not high when the photolysis was carried out in the absence of TiO2 and it was negligible in the absence of UV light. The half-life (DT50) of a 20 ppm aqueous solution of phosalone was 15 min in optimized conditions. The plot of lnC (phosalone) vs. time was linear, suggesting first order reaction (K=0.0532 min(-1)). The half-life time of photomineralization in the concentration range of 7.5-20 ppm was 13.02 min. The efficiency of the method was also determined by measuring the reduction of Chemical Oxygen Demand (COD). During the mineralization under optimized conditions, COD decreased by more than 45% at irradiation time of 15 min. The photodegradation of phosalone was enhanced by addition of proper amount of hydrogen peroxide (150 ppm).     

Effect of adsorbents coated with titanium dioxide on the photocatalytic degradation of propoxur

Photocatalytic oxidation of pesticides in aqueous media irradiated by UV light is a rapidly growing field of research. Therefore, the treatment technology for degradation of propoxur (an insecticide) using titanium dioxide coated on the supports such as activated carbon, zeolite, brick, quartz and glass beads, was performed in this research. Results show that GAC/TiO2 is the best complexing agent for oxidizing propoxur because of its adsorption properities. The others follow the sequence: plain TiO2 > glass beads > zeolite > brick > quartz. The degradation rate of propoxur with plain TiO2 is higher than that with TiO2/GAC complexing agent. But the mineralization rate of propoxur with plain TiO2 is lower than that with TiO2/GAC complexing agent. However, it can be concluded that using GAC as the support can improve the photocatalytic efficiency.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

固定化催化剂TiO2膜光催化降解三氯乙醛的研究

研究了负载于玻璃上的固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果,探讨了TiO2膜光催化降解三氯乙醛的机理,考察了溶液pH值和三氯乙醛初始浓度埘TiO2膜光催化降解三氯乙醛的影响,并研究了固定化催化剂TiO2膜光催化降解三氯乙醛的动力学.结果表明,固定化催化剂TiO2膜光催化降解水中三氯乙醛的效果良好,当三氯乙醛初始浓度为2.25 mg/L时,在紫外光照时间3 h下,三氯乙醛的降解率高达100%.在相司紫外光照时间下,三氯乙醛的光催化降解率随着三氯乙醛初始浓度的增大而下降.在溶液pH=6.5时,三氯乙醛的降解效率最高.固定化催化剂TiO2膜光催化降解三氯乙醛的反应遵循一级反应动力学,反应速率常数随三氯乙醛初始浓度的增大而减小.     

TiO2纳米管催化降解4，4’-二溴联苯的影响因素和动力学研究

利用TiO₂纳米管催化降解水中的4，4’-二溴联苯，对催化降解过程和影响因素进行研究。结果表明，TiO₂纳米管对其有较高的催化降解效率且降解过程符合Langmuir-Hinshelwood动力学模式。不同光源、4，4’-二溴联苯的初始浓度、纳米管添加量和pH值对催化降解过程都有较大影响，其中pH值的影响最为明显。反应液在中性状态下的降解率明显低于pH=1或11的情况。在pH=1时，4，4’-二溴联苯的降解率达86%。     

Photochemical and photocatalytic degradation of gaseous toluene using short-wavelength UV irradiation with TiO2 catalyst: comparison of three UV sources

The feasibility of the use of short-wavelength UV (254+185 nm) irradiation and TiO2 catalyst for photodegradation of gaseous toluene was evaluated. It was clear that the use of TiO2 under 254+185 nm light irradiation significantly enhanced the photodegradation of toluene relative to UV alone, owed to the combined effect of photochemical oxidation in the gas phase and photocatalytic oxidation on TiO2. The photodegradation with 254+185 nm light irradiation was compared with other UV wavelengths (365 nm (black light blue lamp) and 254 nm (germicidal UV lamp)). The highest conversion and mineralization were obtained with the 254+185 nm light. Moreover, high conversions were achieved even at high initial concentrations of toluene. Catalyst deactivation was also prevented with the 254+185 nm light. Regeneration experiments with the deactivated catalyst under different conditions revealed that reactive oxygen species played an important role in preventing catalyst deactivation by decomposing effectively the less reactive carbon deposits on the TiO2 catalyst. Simultaneous elimination of photogenerated excess ozone and residual organic compounds was accomplished by using a MnO2 ozone-decomposition catalyst to form reactive species for destruction of the organic compounds.     

Non-degradable triazine substrates of atrazine and cyanuric acid hydrothermally and in supercritical water under the UV-illuminated photocatalytic cooperation

Strong oxidation by titanium dioxide photocatalysis can occur by photodegradation of organic contaminants in air and water. Some endocrine disruptors such as 2,4-dichlorophenoxy acetic acid (;;; ), 2,4-dichlorophenol (;;; ), nonylphenol (; ), bisphenol A (), diethyl phthalate (; ), etc. which can be neither biodegraded by bacteria nor degraded thermally can be degraded by TiO(2) photocatalytic treatment. However, incomplete photomineralization partly occurred, when TiO(2) photocatalytic degradation is employed for the treatment of certain endocrine disruptors. For example, no atrazine pesticide having triazine skeleton can be completely mineralized even by a photocatalytic procedure; the photodegradation of atrazine ultimately stops at the intermediate step of cyanuric acid, which cannot be photodegraded even after long illumination times ().In this study, the decomposition of atrazine and cyanuric acid was carried out with a device combining photocatalytic degradation in supercritical water (scH(2)O) or hydrothermal water (hyH(2)O). Atrazine and cyanuric acid can be degraded by the cooperation of either scH(2)O or hyH(2)O and UV illuminated TiO(2)-photocatalytic dispersed system under the fixed pressure of 23 MPa at 623 K or 683 K in a 120-ml Hastelloy batch reactor. The photocatalytic degradation method under high temperature and pressure has found appropriate for the photocatalytic oxidation of acetic acid and 2-chlorobiphenyl under continuous flow conditions at 160 degrees C and 20 atm (). In addition, the wet peroxide oxidation of PCBs by high temperature and pressure has been reported (). The main aims of this research are following. (i): the degradation of atrazine and cyanuric acid within the scH(2)O or hyH(2)O, (ii) the decomposition of atrazine and cyanuric acid catalyzed by TiO(2) particles under scH(2)O or hyH(2)O, and the synergistic effect for several reactions with TiO(2) and scH(2)O or hyH(2)O, and (iii) the mineralization yield of nitrogen and chlorine atoms concerning the chemical structures of atrazine or cyanuric acid (only nitrogen).     

Trichloroethylene degradation by photocatalysis in annular flow and annulus fluidized bed photoreactors

The effects of trichloroethylene (TCE) gas flow rate, relative humidity, TiO(2) film thickness, and UV light intensity on photodegradation of TCE have been determined in an annular flow type photoreactor. Phosgene and dichloroacetyl chloride formation could be controlled as a function of TCE gas flow rate and photodegradation of TCE decreased with increasing relative humidity. The optimum thickness of TiO(2) film was found to be approximately 5 mum and the photocatalytic reaction rate of TCE increased with square root of UV light intensity. In addition, the effects of the initial TCE concentration, phase holdup ratio of gas and solid phases (epsilon(g)/epsilon(s)), CuO loading on the photodegradation of TCE have been determined in an annulus fluidized bed photoreactor. The TCE photodegradation decreased with increasing the initial TCE concentration. The optimum conditions of the phase holdup ratio (epsilon(g)/epsilon(s)) and CuO wt.% for the maximum photodegradation of TCE was found to be 2.1 and 1.1 wt.%, respectively. Therefore, an annulus fluidized bed photoreactor is an effective tool for TCE degradation over TiO(2)/silica gel with efficient utilization of photon energy.     

Photocatalytic oxidation of heptane in the gas-phase over TiO2.

In this paper, gas-phase photocatalytic oxidation (PCO) of heptane over UV-illuminated TiO2 was carried out at ambient temperature in a batch reactor. Complete oxidation of heptane with almost stoichiometric production of CO2 and H2O was observed. The intermediates detected were propanal, butanal, 3-heptanone, 4-heptanone and carbon monoxide. A scheme of the possible mechanism for PCO of heptane over TiO2 was suggested. Langmuir-Hinshelwood kinetics equation was obtained from the results at different initial concentrations of heptane, oxygen, moisture and light intensity. The photocatalytic activity of TiO2 can be sustained indefinitely. This can be attributed to the production of water in the system, which can replenish the consumed hydroxyl radicals.     

Degradation of azo dye Procion Red MX-5B by photocatalytic oxidation

The photocatalytic oxidation (PCO) of a monoazo dye Procion Red MX-5B under various physico-chemical conditions was investigated. Degradation of the dye by PCO was enhanced by augmentation in UV intensity, titanium dioxide and hydrogen peroxide concentrations but was inhibited by increase in initial dye concentration. The PCO process was affected by pH in a peculiar way. In the presence of 100 mg/l of TiO2 and the absence of H2O2, the highest reaction rate was observed when the initial pH was 10. With 500 mg/l of TiO2 and 10 mM of H2O2, the reaction was the fastest at initial pH of 3-5. The optimal conditions for the degradation of the dye, at an UV intensity of 17 mW/cm2, were determined to be: TiO2 concentration, 500 mg/l; initial H2O2 concentration, 10 mM; initial pH, 5.0. Monitoring of TOC loss showed that the dye was mineralized by 90% within 80 min under these conditions. Nevertheless, the persistence of a low level of TOC indicated that mineralization was not complete and dead-end product(s) which was (were) resistant to PCO might have accumulated.     

The pH and anion effects on the heterogeneous photocatalytic degradation of o-methylbenzoic acid in TiO2 aqueous suspension

This investigation used UV light of 365 nm and titanium dioxide in aqueous suspension to study the photocatalytic reaction of o-methylbenzoic acid under the influence of pH values, anion additives and the varieties of titanium dioxide. From experimental results, under the condition of 5 g/l TiO2, pH 3 and light intensity of 2.45 mW/cm2, 0.1 mM of o-methylbenzoic acid could be completely decomposed in 2 h. The reaction was faster with lowering pH, and was found to be apparent first-order following Langmuir-Hinshelwood model. In the presence of anion additives, the inhibitive effect of chloride ions was larger than that of sulfate ions under acidic condition for Degussa brand titanium dioxide, but without influence using Janssen brand. Both brands, however, promoted the mineralization of o-methylbenzoic acid (o-MBA).     

Titanium dioxide mediated photocatalytic degradation of monochlorobenzene in aqueous phase

The reaction sequence for the photocatalytic degradation of monochlorobenzene (MCB) in UV/TiO2 process, including substrate adsorption, degradation, and mineralization, was studied. The theoretical maximum quantity of MCB that could be adsorbed onto TiO2 surface in aqueous phase was 0.18+/-0.04 micromol m(-2) of TiO2. In accordance with the upper limit of the relative surface coverage of MCB molecules to surface hydroxyls of TiO2 was around 2.2%, the water molecules as the major adjacent species near TiO2 surface would compete with MCB molecules. Increasing the initial substrate concentration to an appropriate value or enhancing the affinity between the MCB and the TiO2 surface by adjusting the solution pH would promote the photocatalytic degradation. Experimental results revealed that the neutral medium was beneficial for the degradation of MCB. In comparison, the mineralization was most improved at acidic condition. Generally, 90% of the total organic carbon (TOC) was mineralized after 240 min illumination time in the examined pH range except solution pH 11. The suppressed mineralization of MCB at solution pH 11 was ascribed to the lack of adsorption. A simplified 2-step consecutive kinetic model was used to simulate the mineralization.     

Degradation of carbofuran in water by solar photocatalysis in presence of photosensitizers

The effect of the presence of photosensitizers, methylene blue (MB) and rose Bengal (RB), on the degradation of carbofuran (2,3-dihydro-2,2-dimethylbenzofuran-7-yl methylcarbamate) in water in a solar photocatalytic system was investigated. It was found that as compared to MB, RB generally showed a stronger effect on the decomposition of carbofuran under comparable conditions. Among the conditions studied, adding 2 x 10(-6) M of RB, that corresponding to 2% of the initial concentration of carbofuran solution in the system, rendered the most effective degradation of carbofuran. As a result, a carbofuran removal percentage of 69.9%, a mineralization efficiency of 28.0%, and a microtoxicity reduction of 65.0% could be achieved. The degradation and mineralization of carbofuran was found to follow the pseudo-first order reaction kinetics. The decomposition mechanism of carbofuran was further investigated through identification of the intermediates to elaborate the influence of dye photosensitizer on the solar photocatalysis of carbofuran in water. On the basis of the intermediates identified, including carbofuran phenol, 3-hydroxy carbofuran phenol, and substituted alcohols (3-phenoxy 1-propanol, 2-ethyl 1-hexanol, 2-butoxyl ethanol), it appears that hydrolysis and hydroxylation were the two key mechanisms for decomposing carbofuran during the process of solar photocatalysis with the aid of dye photosensitizer.