Characterisation of PM10 and PM2.5 particulate matter in the ambient air of Milan (Italy)

24-h simultaneous samplings of PM10 and PM2.5 particulate matter (PM) have been carried out during the period December 1997–September 1998 in the central urban area of Milan. The mass concentrations of the two fractions showed significant daily variations linked to different thermodynamic conditions of the planetary boundary layer (PBL) and characterised by higher values during wintertime. The elemental composition, determined by energy dispersive X-ray fluorescence technique, was quite different in the two fractions: in the finer one the presence of elements with crustal origin is reduced while the anthropogenic elements, with a relevant environmental and health impact, appear to be enriched. The composition data allowed a quantification of two major components of the atmospheric particulate: sulphates (mainly of secondary origin) and particles with crustal origin. An important but unmeasured component is likely constituted by organic and elemental carbon compounds.The multivariate analysis of elements, gaseous pollutants and mass concentration data-sets leads to the identification of four main sources contributing to PM10 and PM2.5 composition: vehicles exhaust emissions, resuspended crustal dust, secondary sulphates and industrial emissions. The existence of a possible background component with non-local origin is also suggested.     

Characterization of PM2.5 aerosols dominated by local pollution and Asian dust observed at an urban site in Korea during aerosol characterization experiments (ACE)--Asia Project

Daily fine particulate matter (PM2.5) samples were collected at Gwangju, Korea, during the Aerosol Characterization Experiments (ACE)-Asia Project to determine the chemical properties of PM2.5 originating from local pollution and Asian dust (AD) storms. During the study period, two significant events occurred on April 10-13 and 24-25, 2001, and a minor event occurred on April 19, 2001. Based on air mass transport pathways identified by back-trajectory calculation, the PM2.5 dataset was classified into three types of aerosol populations: local pollution and two AD aerosol types. The two AD types were transported along different pathways. One originated from Gobi desert area in Mongolia, passing through Hunshandake desert in Northern Inner Mongolia, urban and polluted regions of China (AD1), and the other originated in sandy deserts located in the Northeast Inner Mongolia Plateau and then flowed southward through the Korean peninsula (AD2). During the AD2 event, a smoke plume that originated in North Korea was transported to our study site. Mass balance closures show that crustal materials were the most significant species during both AD events, contributing -48% to the PM2.5 mass; sulfate aerosols (19.1%) and organic matter (OM; 24.6%) were the second greatest contributors during the AD1 and AD2 periods, respectively, indicating that aerosol properties were dependent on the transport pathway. The sulfate concentration constituted only 6.4% (4.5 microg/m3) of the AD2 PM2.5 mass. OM was the major chemical species in the local pollution-dominated PM2.5 aerosols, accounting for 28.7% of the measured PM2.5 mass, followed by sulfate (21.4%), nitrate (15%), ammonium (12.8%), elemental carbon (8.9%), and crustal material (6.5%). Together with substantial enhancement of the crustal elements (Mg, Al, K, Ca, Sc, Ti, Mn, Fe, Sr, Zr, Ba, and Ce), higher concentrations of pollution elements (S, V, Ni, Zn, As, Cd, and Pb) were observed during AD1 and AD2 than during the local pollution period, indicating that, in addition to crustal material, the AD dust storms also had a significant influence on anthropogenic elements.     

PM10 and PM2.5 source apportionment in the Barcelona Metropolitan area, Catalonia, Spain

Levels of total suspended particles, PM10, PM2.5 and PM1 were continuously monitored at an urban kerbside in the Metropolitan area of Barcelona from June 1999 to June 2000. The results show that hourly levels of PM2.5 and PM1 are consistent with the daily cycle of gaseous pollutants emitted by traffic, whereas TSP and PM10 do not follow the same trend, at least in the diurnal period. The PM2.5/PM10 ratio is dependent on the traffic emissions, whereas additional contribution sources for the >10 μm fraction must be taken into account in the diurnal period. Different PM10 and PM2.5 source apportionment techniques were compared. A methodology based on the chemical determination of 83% of both PM10 and PM2.5 masses allowed us to quantify the marine (4% in PM10 and <1% in PM2.5), crustal (26% in PM10 and 8% in PM2.5) and anthropogenic (54% in PM10 and 73% in PM2.5) loads. Peaks of crustal contribution to PM10 (up to 44% of the PM10 mass) were recorded under Saharan air mass intrusions. A different seasonal trend was observed for levels of sulphate and nitrate, probably as a consequence of the different thermodynamic behaviour of these PM species and the higher summer oxidation rate of SO₂.     

Chemical characterisation of PM episodes in NE Spain

The chemical composition of ambient particulate matter (PM) varies widely as a function of its main emission sources and of the chemical reactions which take place in the atmosphere. The aim of this study is to obtain the chemical profile of PM10 and PM2.5 during peak PM episodes, thus identifying the main emission sources and/or atmospheric processes which originate the PM episodes. To this end, cluster analysis was applied to a set of PM10 and PM2.5 data collected throughout 2001 in two urban and industrialised areas in NE Spain. As a result of this analysis, five clusters were identified for each site, and the interpretation of their chemical profiles lead to the identification of five types of peak PM episodes for each site: industrial, traffic and regional re-circulation episodes at both sites, plus crustal episodes in Barcelona, and peak traffic and industrial episodes (T+I) in Tarragona. Traffic episodes are characterised by daily means of 23 and 10 microg/m3 of OM+EC in Barcelona and Tarragona in PM10. Levels of secondary inorganic aerosols reach average daily means of 19 and 11 microg/m3 in Barcelona and Tarragona in PM10 during industrial episodes. High levels of sulphate (>5 microg/m3) and ozone (up to 77 microg/m3 daily mean) are good tracers of regional re-circulation episodes. During crustal episodes daily means of crustal elements reach up to 34 microg/m3 in Barcelona. Special attention has been drawn to the composition of the mineral matter during the different PM episodes.     

Development and evaluation of a continuous coarse (PM10-PM2.5) particle monitor

In this paper, we describe the development and laboratory and field evaluation of a continuous coarse (2.5-10 microm) particle mass (PM) monitor that can provide reliable measurements of the coarse mass (CM) concentrations in time intervals as short as 5-10 min. The operating principle of the monitor is based on enriching CM concentrations by a factor of approximately 25 by means of a 2.5-microm cut point round nozzle virtual impactor while maintaining fine mass (FM)--that is, the mass of PM2.5 at ambient concentrations. The aerosol mixture is subsequently drawn through a standard tapered element oscillating microbalance (TEOM), the response of which is dominated by the contributions of the CM, due to concentration enrichment. Findings from the field study ascertain that a TEOM coupled with a PM10 inlet followed by a 2.5-microm cut point round nozzle virtual impactor can be used successfully for continuous CM concentration measurements. The average concentration-enriched CM concentrations measured by the TEOM were 26-27 times higher than those measured by the time-integrated PM10 samplers [the micro-orifice uniform deposit impactor (MOUDI) and the Partisol] and were highly correlated. CM concentrations measured by the concentration-enriched TEOM were independent of the ambient FM-to-CM concentration ratio, due to the decrease in ambient coarse particle mass median diameter with an increasing FM-to-CM concentration ratio. Finally, our results illustrate one of the main problems associated with the use of real impactors to sample particles at relative humidity (RH) values less than 40%. While PM10 concentrations obtained by means of the MOUDI and Partisol were in excellent agreement, CM concentrations measured by the MOUDI were low by 20%, and FM concentrations were high by a factor of 5, together suggesting particle bounce at low RH.     

Analysis of PM10, PM2.5, and PM2 5-10 concentrations in Santiago, Chile, from 1989 to 2001

Daily particle samples were collected in Santiago, Chile, at four urban locations from January 1, 1989, through December 31, 2001. Both fine PM with da < 2.5 microm (PM2.5) and coarse PM with 2.5 < da < 10 microm (PM2.5-10) were collected using dichotomous samplers. The inhalable particle fraction, PM10, was determined as the sum of fine and coarse concentrations. Wind speed, temperature and relative humidity (RH) were also measured continuously. Average concentrations of PM2.5 for the 1989-2001 period ranged from 38.5 microg/m3 to 53 microg/m3. For PM2.5-10 levels ranged from 35.8-48.2 microg/m3 and for PM10 results were 74.4-101.2 microg/m3 across the four sites. Both annual and daily PM2.5 and PM10 concentration levels exceeded the U.S. National Ambient Air Quality Standards and the European Union concentration limits. Mean PM2.5 levels during the cold season (April through September) were more than twice as high as those observed in the warm season (October through March); whereas coarse particle levels were similar in both seasons. PM concentration trends were investigated using regression models, controlling for site, weekday, month, wind speed, temperature, and RH. Results showed that PM2.5 concentrations decreased substantially, 52% over the 12-year period (1989-2000), whereas PM2.5-10 concentrations increased by approximately 50% in the first 5 years and then decreased by a similar percentage over the following 7 years. These decreases were evident even after controlling for significant climatic effects. These results suggest that the pollution reduction programs developed and implemented by the Comisión Nacional del Medio Ambiente (CONAMA) have been effective in reducing particle levels in the Santiago Metropolitan region. However, particle levels remain high and it is thus imperative that efforts to improve air quality continue.     

Wintertime vertical variations in particulate matter (PM) and precursor concentrations in the San Joaquin Valley during the California Regional Coarse PM/Fine PM Air Quality Study

Air quality monitoring was conducted at a rural site with a tower in the middle of California's San Joaquin Valley (SJV) and at elevated sites in the foothills and mountains surrounding the SJV for the California Regional PM10/ PM2.5 Air Quality Study. Measurements at the surface and n a tower at 90 m were collected in Angiola, CA, from December 2000 through February 2001 and included hourly black carbon (BC), particle counts from optical particle counters, nitric oxide, ozone, temperature, relative humidity, wind speed, and direction. Boundary site measurements were made primarily using 24-hr integrated particulate matter (PM) samples. These measurements were used to understand the vertical variations of PM and PM precursors, the effect of stratification in the winter on concentrations and chemistry aloft and at the surface, and the impact of aloft-versus-surface transport on PM concentrations. Vertical variations of concentrations differed among individual species. The stratification may be important to atmospheric chemistry processes, particularly nighttime nitrate formation aloft, because NO2 appeared to be oxidized by ozone in the stratified aloft layer. Additionally, increases in accumulation-mode particle concentrations in the aloft layer during a fine PM (PM2.5) episode corresponded with increases in aloft nitrate, demonstrating the likelihood of an aloft nighttime nitrate formation mechanism. Evidence of local transport at the surface and regional transport aloft was found; transport processes also varied among the species. The distribution of BC appeared to be regional, and BC was often uniformly mixed vertically. Overall, the combination of time-resolved tower and surface measurements provided important insight into PM stratification, formation, and transport.     

Source apportionment of PM2.5 and PM10 aerosols in Brisbane (Australia) by receptor modelling

Aerosol samples for PM_2.5 and PM₁₀ (particulate matter with aerodynamic diameters less than 2.5 and 10 μm, respectively) were collected from 1993 to 1995 at five sites in Brisbane, a subtropical coastal city in Australia. This paper investigates the contributions of emission sources to PM_2.5 and PM₁₀ aerosol mass in Brisbane. Source apportionment results derived from the chemical mass balance (CMB), target transformation factor analysis (TTFA) and multiple linear regression (MLR) methods agree well with each other. The contributions from emission sources exhibit large variations in particle size with temporal and spatial differences. On average, the major contributors of PM₁₀ aerosol mass in Brisbane include: soil/road side dusts (25% by mass), motor vehicle exhausts (13%, not including the secondary products), sea salt (12%), Ca-rich and Ti-rich compounds (11%, from cement works and mineral processing industries), biomass burning (7%), and elemental carbon and secondary products contribute to around 15% of the aerosol mass on average. The major sources of PM_2.5 aerosols at the Griffith University (GU) site (a suburban site surrounded by forest area) are: elemental carbon (24% by mass), secondary organics (21%), biomass burning (15%) and secondary sulphate (14%). Most of the secondary products are related to motor vehicle exhausts, so, although motor vehicle exhausts contribute directly to only 6% of the PM_2.5 aerosol mass, their total contribution (including their secondary products) could be substantial. This pattern of source contribution is similar to the results for Rozelle (Sydney) among the major Australian studies, and is less in contributions from industrial and motor vehicular exhausts than the other cities. An attempt was made to estimate the contribution of rural dust and road side dust. The results show that road side dusts could contribute more than half of the crustal matter. More than 80% of the contribution of vehicle exhausts arises from diesel-fuelled trucks/buses. Biomass burning, large contributions of crustal matter, and/or local contributing sources under calm weather conditions, are often the cause of the high PM₁₀ episodes at the GU site in Brisbane.     

Evaluation of time-resolved PM2.5 data in urban/suburban areas of New Jersey

Time-resolved data is needed for public notification of unhealthful air quality and to develop an understanding of atmospheric chemistry, including insights important to control strategies. In this research, continuous fine particulate matter (PM2.5) mass concentrations were measured with tapered element oscillating microbalances (TEOMs) across New Jersey from July 1997 to June 1998. Data features indicating the influence of local sources and long-distance transport are examined, as well as differences between 1-hr maxima and 24-hr average concentrations that might be relevant to acute health effects. Continuous mass concentrations were not significantly different from filter-collected gravimetric mass concentrations with 95% confidence intervals during any season. Annual mean PM2.5 concentrations from July 1997 to June 1998 were 17.3, 16.4, 14.1, and 15.3 micrograms/m3 at Newark, Elizabeth, New Brunswick, and Camden, NJ, respectively. Monthly averaged 24- and 1-hr daily maximum PM2.5 concentrations suggest the existence of a high PM2.5 (May-October) and a low PM2.5 (November-April) season. PM2.5 magnitudes and temporal trends were very similar across the state during high PM2.5 events. In fact, the between-site coefficients of determination (R2) for daily PM2.5 measurements were 84-98% for June and July. Additionally, during the most pronounced PM2.5 episode, PM2.5 concentrations closely tracked the daily maximum 1-hr O3 concentrations. These observations suggest the importance of transport and atmospheric chemistry (i.e., secondary formation) to PM2.5 episodes in New Jersey. The influence of local sources was observed in diurnal concentration profiles and annual average between-site differences. Urban wintertime data illustrate that high 1-hr maximum PM2.5 concentrations can occur on low 24-hr PM2.5 days.     

Particulate matter in California: part 2--Spatial, temporal, and compositional patterns of PM2.5, PM10-2.5, and PM10

Geographic and temporal variations in the concentration and composition of particulate matter (PM) provide important insights into particle sources, atmospheric processes that influence particle formation, and PM management strategies. In the nonurban areas of California, annual-average PM2.5 and PM10 concentrations range from 3 to 10 microg/m3 and from 5 to 18 microg/m3, respectively. In the urban areas of California, annual-averages for PM2.5 range from 7 to 30 microg/m3, with observed 24-hr peaks reaching levels as high as 160 microg/m3. Within each air basin, exceedances are a mixture of isolated events as well as periods of elevated PM2.5 concentrations that are more prolonged and regional in nature. PM2.5 concentrations are generally highest during the winter months. The exception is the South Coast Air Basin, where fairly high values occur throughout the year. Annual-average PM2.5 mass, as well as the concentrations of major components, declined from 1988 to 2000. The declines are especially pronounced for the sulfate (SO4(2-)) and nitrate (NO3-) components of PM2.5 and PM10) and correlate with reductions in ambient levels of oxides of sulfur (SOx) and oxides of nitrogen (NOx). Annual averages for PM10-2.5 and PM10 exhibited similar downwind trends from 1994 to 1999, with a slightly less pronounced decrease in the coarse fraction.     

Wintertime Vertical Variations in Particulate Matter (PM) and Precursor Concentrations in the San Joaquin Valley during the California Regional Coarse PM/Fine PM Air Quality Study

Abstract

Air quality monitoring was conducted at a rural site with a tower in the middle of California’s San Joaquin Valley (SJV) and at elevated sites in the foothills and mountains surrounding the SJV for the California Regional PM₁₀/M_2.5 Air Quality Study. Measurements at the surface and on a tower at 90 m were collected in Angiola, CA, from ecember 2000 through February 2001 and included hourly black carbon (BC), particle counts from optical particle counters, nitric oxide, ozone, temperature, relative humidity, wind speed, and direction. Boundary site measurements were made primarily using 24-hr integrated particulate matter (PM) samples. These measurements were used to understand the vertical variations of PM and PM precursors, the effect of stratification in the winter on concentrations and chemistry aloft and at the surface, and the impact of aloft-versus-surface transport on PM concentrations. Vertical variations of concentrations differed among individual species. The stratification may be important to atmospheric chemistry processes, particularly nighttime nitrate formation aloft, because NO₂ appeared to be oxidized by ozone in the stratified aloft layer. Additionally, increases in accumulation-mode particle concentrations in the aloft layer during a fine PM (PM_2.5) episode corresponded with increases in aloft nitrate, demonstrating the likelihood of an aloft nighttime nitrate formation mechanism. Evidence of local transport at the surface and regional transport aloft was found; transport processes also varied among the species. The distribution of BC appeared to be regional, and BC was often uniformly mixed vertically. Overall, the combination of time-resolved tower and surface measurements provided important insight into PM stratification, formation, and transport.     

The Steubenville Comprehensive Air Monitoring Program (SCAMP): concentrations and solubilities of PM(2.5) trace elements and their implications for source apportionment and health research

The elemental compositions of the water-soluble and acid-digestible fractions of 24-hr integrated fine particulate matter (PM(2.5)) samples collected in Steubenville, OH, from 2000 to 2002 were determined using dynamic reaction cell inductively coupled plasma-mass spectrometry. The water-soluble elemental compositions of PM(2.5) samples collected at four satellite monitoring sites in the surrounding region were also determined. Fe was the most abundant but least water soluble of the elements determined at the Steubenville site, having a mean ambient concentration of 272 ng/m3 and a median fractional solubility of 6%. Fe solubility and its correlations with SO4(2-) and temperature varied significantly by season, consistent with the hypothesis that secondary sulfates may help to mobilize soluble Fe under suitable summertime photochemical conditions. Significantly higher ambient concentrations were observed at Steubenville than at each of the four satellite sites for 10 of the 18 elements (Al, As, Ca, Cd, Fe, Mg, Mn, Na, Pb, and Zn) determined in the water-soluble PM(2.5) fraction. Concentrations of Fe, Mn, and Zn at Steubenville were substantially higher than concentrations reported recently for larger U.S. cities. Receptor modeling identified seven sources affecting the Steubenville site. An (NH4)2SO4-dominated source, likely representing secondary PM(2.5) from coal-fired plants to the west and southwest of Steubenville, accounted for 42% of the PM(2.5) mass, and two sources likely dominated by emissions from motor vehicles and from iron and steel facilities in the immediate Steubenville vicinity accounted for 20% and 10%, respectively. Other sources included an NH4NO3 source (15%), a crustal source (6%), a mixed nonferrous metals and industrial source (3%), and a primary coal combustion source (3%). Results suggest the importance of very different regional and local source mechanisms in contributing to PM(2.5) mass at Steubenville and reinforce the need for further research to elucidate whether metals such as Fe, Mn, and Zn play a role in the PM(2.5) health effects observed previously there.     

Chemical speciation of PM2.5 and PM10 in south Phoenix, AZ, USA

Phoenix, AZ, experiences high particulate matter (PM) episodes, especially in the wintertime. The spatial variation of the PM concentrations and resulting differences in exposure is of particular concern. In this study, PM2.s (PM with aerodynamic diameter <2.5 microm) and PM10 (PM with aerodynamic diameter <10 microm) samples were collected simultaneously from the east and west sides of South Phoenix and at a control site in Tempe and analyzed for trace elements and bulk elemental and organic carbon. Measurements showed that although PM2.5 concentrations had similar trends in temporal scale across all sites, concentrations of PM10 did not. The difference in PM10 concentrations and fluctuation across the three sites suggest effects of a local soil source as evidenced by high concentrations of Al, Ca, and Fe in PM10. K and anthropogenic elements (e.g., Cu, Pb, and Zn) in PM2.5 samples on January 1 were strikingly high, suggesting the influence of New Year's fireworks. Concentrations of toxic elements (e.g., Pb) in the study presented here are not different from similar studies in other U.S. cities. Application of principal component analysis indicated two broad categories of emission sources--soil and combustion--together accounting for 80 and 90% of variance, respectively, in PM2.5 and PM10. The soil and combustion components explained approximately 60 and 30% of the variance in PM10, respectively, whereas combustion sources dominated PM2.5 (>50% variance). Many elements associated with anthropogenic sources were highly enriched, with enrichment factors in PM2.5 an order of magnitude higher than in PM10 relative to surface soil composition in the study area.     

Characterization of PM2.5 and PM10 in the South Coast Air Basin of southern California: Part. 2--Temporal variations

The South Coast Air Quality Management District (SCAQMD) conducted a 1-year special particulate monitoring study from January 1995 to February 1996. This monitoring data indicates that high PM10 and PM2.5 concentrations were observed in the fall (October, November, and December), with November concentrations being the highest. During the rest of the year, PM2.5 and PM10 masses gradually increased from January to September. Monthly PM10 mass varied from 20 to 120 micrograms/m3, and monthly PM2.5 mass varied from 13 to 63 micrograms/m3. The PM2.5-to-PM10 ratio varied daily and ranged between 22 and 96%. Two types of high-PM days were observed. The first type was observed under fall stagnation conditions, which lead to high secondary species concentrations. The second type was observed under high wind conditions, which lead to high primary coarse particles of crustal components. The highest 24-hr average PM10 concentration (226.3 micrograms/m3) was observed at the Fontana station, while the highest PM2.5 concentration (129.3 micrograms/m3) was observed at the Diamond Bar station.     

Measurements of PM10 and PM2.5 in urban area of Nanjing,China and the assessment of pulmonary deposition of particle mass

Measurement of PM10 and PM2.5 was carried out at six sites of Nanjing, China in the period of February-May 2001. The pH and conductivity of water-soluble matter of PM10 and PM2.5 were determined, and the samples were analyzed for total carbon (TC), organic carbon (OC) and inorganic carbon (IC) of the water-soluble fraction. The distribution of aerosol mass concentration in size was also measured at one site SB by a nine-stage impactor followed to assess the pulmonary deposition of particles in different tracts of the human respiratory system. Compared with National Ambient Air Quality Standard (NAAQS) of the USA, the level of PM10 and PM2.5 in Nanjing was much higher. Especially for site SY, the average particle mass concentrations (774.5 micrograms/m3 for PM10 and 481.4 micrograms/m3 for PM2.5) were more than five times the NAAQS standard. At site SB aerosol mass distribution in size had shown the similar characteristics with accumulation (Dp < 1 micron) and coarse (Dp > 1 micron) modes. More than 70% of total suspended particles is of a size that they are deposited in the respiratory tract below trachea, whereas about 22% of the mass is respirable and will reach the alveoli. Water-soluble fractions of PM10 and PM2.5 in Nanjing are acidic, and the pH of PM2.5 is lower than that of PM10. OC makes up the majority of TC and accounts for 3-14% of mass concentration of PM10 and/or PM2.5, while IC only accounts for 0.1-0.5% of PM10 and/or PM2.5 mass.     

Monitoring of PM10 and PM2.5 around primary particulate anthropogenic emission sources

Investigations on the monitoring of ambient air levels of atmospheric particulates were developed around a large source of primary anthropogenic particulate emissions: the industrial ceramic area in the province of Castelló (Eastern Spain). Although these primary particulate emissions have a coarse grain-size distribution, the atmospheric transport dominated by the breeze circulation accounts for a grain-size segregation, which results in ambient air particles occurring mainly in the 2.5–10 μm range. The chemical composition of the ceramic particulate emissions is very similar to the crustal end-member but the use of high Al, Ti and Fe as tracer elements as well as a peculiar grain-size distribution in the insoluble major phases allow us to identify the ceramic input in the bulk particulate matter. PM2.5 instead of PM10 monitoring may avoid the interference of crustal particles without a major reduction in the secondary anthropogenic load, with the exception of nitrate. However, a methodology based in PM2.5 measurement alone is not adequate for monitoring the impact of primary particulate emissions (such as ceramic emissions) on air quality, since the major ambient air particles derived from these emissions are mainly in the range of 2.5–10 μm. Consequently, in areas characterised by major secondary particulate emissions, PM2.5 monitoring should detect anthropogenic particulate pollutants without crustal particulate interference, whereas PM10 measurements should be used in areas with major primary anthropogenic particulate emissions.     

The study of TSP, PM(2.5-10) and PM2.5 during Taiwan Chi-Chi Earthquake in the traffic site of central Taiwan, Taichung

Ambient particle concentration was taken on the traffic sampling site over the Chung-Chi Road over bridge (CCROB) in front of Hungkuang Institute of Technology (HKIT). The sampling time was from August 1999 to December 1999. During the sampling period, Taiwan's biggest earthquake in more than a century registered 7.3 on the Richter scale (Taiwan Chi-Chi Earthquake). Besides, there were more than 20,000 aftershocks that followed the Taiwan Chi-Chi Earthquake within three months. Thus, the PM2.5, PM(2.5-10) particle concentrations were also collected then and compared with total suspended particle (TSP) in this study. The average PM(2.5-10), PM2.5 and TSP concentrations are 24.6, 58.0 and 106 microg/m3, respectively, after the Taiwan Chi-Chi Earthquake. The average TSP concentrations before and after Taiwan Chi-Chi Earthquake were 70 and 127 microg/m3, respectively. It is clearly shown that the average concentration of TSP after Taiwan Chi-Chi Earthquake was about 1.8 times as that of TSP concentration before Taiwan Chi-Chi Earthquake in the traffic site of central Taiwan. And the ratios of PM2.5/PM(2.5-10), PM2.5/PM10 and PM2.5/TSP are 2.2%, 67.2%, 38.9%, respectively. The results also indicated about Chi-Chi fine particle concentration (PM25) and the TSP increases in the traffic site of central Taiwan after Taiwan Chi-Chi Earthquake.     

Source apportionment of PM10 and PM2.5 in five Chilean cities using factor analysis

Chile is a fast-growing country with important industrial activities near urban areas. In this study, the mass and elemental concentrations of PM10 and PM2.5 were measured in five major Chilean urban areas. Samples of particles with diameter less than 10 microm (PM10) and 2.5 microm (PM2.5) were collected in 1998 in Iquique (northern Chile), Valparaiso, Vi?a del Mar, Rancagua (central Chile), and Temuco (southern Chile). Both PM10 and PM2.5 annual mean concentrations (PM10: 56.9-77.6 microg/m3; PM2.5: 22.4-42.6 microg/m3) were significantly higher than the corresponding European Union (EU) and U.S. Environmental Protection Agency (EPA) air quality standards. Moreover, the 24-hr PM10 and PM2.5 U.S. standards were exceeded infrequently for some of the cities (Rancagua and Valparaiso). Elements ranging from Mg to Pb were detected in the aerosol samples using X-ray fluorescence (XRF). For each of the five cities, factor analysis (FA) was applied to identify and quantify the sources of PM10 and PM2.5. The agreement between calculated and measured mass and elemental concentrations was excellent in most of the cities. Both natural and anthropogenic sources were resolved for all five cities. Soil and sea were the most important contributors to coarse particles (PM10-PM2.5), whereas their contributions to PM2.5 were negligible. Emissions from Cu smelters and oil refineries (and/or diesel combustion) were identified as important sources of PM2.5, particularly in the industrial cities of Rancagua, Valparaiso, and Vi?a del Mar. Finally, motor vehicles and wood burning were significant sources of both PM2.5 and PM10 in most of the cities (wood burning was not identified in Iquique).     

Fine (PM2.5), coarse (PM2.5-10), and metallic elements of suspended particulates for incense burning at Tzu Yun Yen temple in central Taiwan

Ambient suspended particulate concentrations were measured at Tzu Yun Yen temple (120 degrees, 34('), 10(") E; 24 degrees, 16('), 12(") N) in this study. This is representative of incense burning and semi-open sampling sites. The Universal-sampler collected fine and coarse particle material was used to measure suspended particulate concentrations, and sampling periods were from 16/08/2001 to 2/1/2002 at Tzu Yun Yen temple. In addition, metallic element concentrations, compositions of PM(2.5) and PM(2.5-10) for incense burning at Tzu Yun Yen temple were also analyzed in this study. The PM(2.5)/PM(10) ratios ranged between 31% and 87% and averaged 70+/-11% during incense the burning period, respectively. The median metallic element concentration order for these elements is Fe>Zn>Cr>Cd>Pb>Mn>Ni>Cu in fine particles (PM(2.5)) at the Tzu Yun Yen temple sampling site. The median metallic element concentration order for these elements is Fe>Zn>Cr>Pb>Cd>Ni>Mn>Cu in coarse particle (PM(2.5-10)) at the Tzu Yun Yen temple sampling site. Fine particulates (PM(2.5)) are the main portion of PM(10) at Tzu Yun Yen temple in this study. From the point of view of PM(10), these data reflect that the elements Fe, Zn, and Cr were the major elements distributed at Tzu Yun Yen temple in this study.     

Spatial and temporal characterization of PM2.5 mass concentrations in California, 1980-2007

Systematic measurement of fine particulate matter (aerodynamic diameter less than 2.5 microm [PM2.5]) mass concentrations began nationally with implementation of the Federal Reference Method (FRM) network in 1998 and 1999. In California, additional monitoring of fine particulate matter (PM) occurred via a dichotomous sampler network and several special studies carried out between 1982 and 2002. The authors evaluate the comparability of FRM and non-FRM measurements of PM2.5 mass concentrations and establish conversion factors to standardize fine mass measurements from different methods to FRM-equivalent concentrations. The authors also identify measurements of PM2.5 mass concentrations that do not agree with FRM or other independent PM2.5 mass measurements. The authors show that PM2.5 mass can be reconstructed to a high degree of accuracy (r2 > 0.9; mean absolute error approximately 2 microg m(-3)) from PM with an aerodynamic diameter < or =10 microm (PM10) mass and species concentrations when site-specific and season-specific conversion factors are used and a statewide record of fine PM mass concentrations by combining the FRM PM2.5 measurements, non-FRM PM2.5 measurements, and reconstructions of PM2.5 mass concentrations. Trends and spatial variations are evaluated using the integrated data. The rates of change of annual fine PM mass were negative (downward trends) at all 22 urban and 6 nonurban (Interagency Monitoring of Protected Visual Environments [IMPROVE]) monitoring locations having at least 15 yr of data during the period 1980-2007. The trends at the IMPROVE sites ranged from -0.05 to -0.25 microg m(-3) yr(-1) (median -0.11 microg m(-3) yr(-1)), whereas urban-site trends ranged from -0.13 to -1.29 microg m(-3) yr(-1) (median -0.59 microg m(-3) yr(-1)). The urban concentrations declined by a factor of 2 over the period of record, and these decreases were qualitatively consistent with changes in emissions of primary PM2.5 and gas-phase precursors of secondary PM. Mean PM2.5 mass concentrations ranged from 3.3 to 7.4 microg m(-3) at IMPROVE sites and from 9.3 to 37.1 microg m(-3) at urban sites.