电化学氧化组合工艺处理垃圾渗滤液

垃圾渗滤液是一种成分复杂、毒性较强且难处理的废水之一。实验采用混凝沉淀-厌氧-电解-好氧一体化组合工艺处理垃圾渗滤液,探索了混凝沉淀池和电解池的运行参数对垃圾渗滤液处理效果的影响,并分析了组合工艺对于6种重金属(Cu、Zn、Cd、Cr和Ni)的去除效果。实验结果表明,以PAC为混凝剂PAM为助凝剂时,投加量分别为1.2 g/L和1mg/L,COD去除率可达57%。电化学工艺阶段,在p H为6.0,电流密度15 m A/cm2,Cl-浓度2 200~2 400 mg/L,电解2.5h,垃圾渗滤液的COD去除率达55.4%。一体化电生物滤池对于重金属的去除具有明显的效果,Cu、Cd和Zn去除率达100%,Ni去除率超过90%,Cr去除率超过80%,COD整体去除率达94%;NH+4-N去除率达97.2%;TN去除率达73.6%。混凝沉淀-厌氧-电化学-好氧的组合工艺来处理垃圾渗滤液,能够有效地去除水体中的重金属及COD、NH+4-N。     

旋转填充床中Fenton＋O3氧化降解模拟阿莫西林废水

以旋转填充床（RPB）作为反应装置，研究了Fenton工艺与Fenton＋O3工艺处理模拟阿莫西林废水的效果，考察了FeSO4·7H2O的投加量、温度、旋转床转速、液体流量及pH对C0D去除率的影响。实验表明，Fenton＋O3工艺的COD脱除率及BOD5／COD相对于Fenton工艺分别提升26．7％和140％。该工艺在pH为3、温度为25℃、液体流量30L／h、气体流量2．5L／h、转速800r／min、H2O2的投加量为1mmol／L及Fe2＋投加量为0．4mm01／L的条件下，100mg／L的模拟阿莫西林废水中COD的去除率达到57．9％，BOD5/COD从0增加到0．36，满足后续生化处理要求。     

Fenton氧化-混凝联合工艺处理络合铜镍废水的研究

采用Fenton试剂氧化-混凝联合工艺对难处理络合铜镍电镀废水进行了研究,考察了废水初始pH值、H2O2初始浓度、[Fe2 ]/[H2O2]、反应时间和温度、混凝液pH、混凝剂质量浓度对处理过程的影响,探讨了废水的降解途径和机理.结果表明,在体系初始pH=4,温度30℃,H2O2投加量为800mg/L,[Fe2 ]/[H2O2]=0.1,反应时间60 min,混凝液pH=8及混凝剂质量浓度为500mg/L的条件下,废水的COD去除率为96.98%,Cu2 为99.91%,Ni2 为99.92%,处理水完全达到国家一级排放标准.同时依据GC/MS对X-GN降解最终产物的分析结果,推导出废水的基本降解机理和途径.     

液体高铁酸钠同时去除电镀废水中氰化物和重金属

采用自制的电化学装置在线制备液体高铁酸钠,然后将制得的高铁酸钠投加到电镀废水中进行处理,考察不同pH值和不同高铁酸钠投加量对废水中总氰化物、Cu~(2+)、Ni~(2+)去除率的影响;对比研究了高铁酸钠氧化法和次氯酸钠氧化法在处理低浓度含氰电镀废水的效果。结果表明,当pH为9~10,高铁酸钠的最佳投加量为0.O.24±0.048 mmol·L~(-1)时,总氰化物、Cu~(2+)和Ni~(2+)的同时去除率均在90%以上;在处理低浓度含氰电镀废水时,高铁酸钠对总氰化物、Cu~(2+)和Ni~(2+)的同时去除率均明显高于次氯酸钠。这是因为高铁酸钠能够有效地氧化多种络合态的氰化物,包括Cu(CN)_4~(3-)、Cu(CN)_4~,Ni(CN)_4~(2-)等使废水中的重金属转变为离子态;然后在碱性条件下在高铁酸盐还原产物-Fe(OH)_3助凝和絮凝作用下,反应生成沉淀达到同时去除氰化物和重金属的目的。     

垃圾填埋场渗滤液物化深度处理研究

通过Fenton法和结合聚合硫酸铁的混凝作用，实现垃圾渗滤液氧化塘出水COD的深度处理；并利用水泥水化产物的凝胶物质，强化COD去除率。30％H2O2投加量为0．75mL／L、七水硫酸亚铁投加量为1．5g／L、n（H2O2）：n（Fe^2＋）=1．2：1（摩尔比）时，Fenton法对渗滤液COD的去除率可达52％；水灰比为2：1、搅拌24h的水泥水化物将Fenton法的出水pH值从4调至10，该工艺流程总的COD去除率为73．6％，较普通的Ca（OH）2调节法提高9．3％，出水COD可以从进水的1200mg／L降至315mg／L。     

淀粉基黄原酸盐处理重金属废水的条件优化研究

采用淀粉基黄原酸盐处理含重金属的电镀废水 ,对淀粉基黄原酸盐的用量、pH值和反应时间等条件进行了研究。结果发现 ,1L含氰电镀废水 (含Cr3+15mg/L、Cu2 +3mg/L、Ni2 +9.2mg/L和Zn2 +6mg/L) ,加入 1g淀粉基黄原酸盐 ,调节 pH为 8,搅拌 1h ,过滤 ,处理后的废水中Cr3+、Cu2 +、Zn2 +和Ni2 +残余浓度分别为 0 .0 8mg/L、0 .0 1mg/L、0 .1mg/L和 0 .0 8mg/L。含有重金属盐的残渣 ,可用硝酸处理 ,以回收重金属     

Fenton氧化-混凝联合工艺处理络合铜镍废水的研究

采用Fenton试剂氧化-混凝联合工艺对难处理络合铜镍电镀废水进行了研究,考察了废水初始pH值、H2O2初始浓度、[Fe^2＋]/[H2O2]、反应时间和温度、混凝液pH、混凝剂质量浓度对处理过程的影响,探讨了废水的降解途径和机理.结果表明,在体系初始pH=4,温度30℃,H2O2投加量为800mg/L,[Fe^2＋]/[H2O2]=0.1,反应时间60 min,混凝液pH=8及混凝剂质量浓度为500mg/L的条件下,废水的COD去除率为96.98%,Cu^2＋为99.91%,Ni^2＋为99.92%,处理水完全达到国家一级排放标准.同时依据GC/MS对X-GN降解最终产物的分析结果,推导出废水的基本降解机理和途径.     

UV/Fenton法预处理橡胶促进剂生产废水

采用UV／Fenton法对橡胶促进剂废水进行预处理。当原水COD约为3000mg／L时，COD去除率可达65％以上，并得到最佳操作条件为：H2O2投加量为8mL／L，Fe^2＋投加量为0．8g／L，反应时间为30rain，pH=5；同时得到Fenton试剂处理该废水的最佳条件为：H2O2投加量为10mL／L，Fe^2＋投加量为0．966g／L，反应时间为30min，pH=5；单独UV作用的最佳工艺条件为：反应时间为20min，pH=5；并就3种处理方法进行了比较，发现UV对Fenton试剂处理橡胶促进剂废水具有一定促进作用。反应前后的紫外光谱说明，经UV／Fenton或Fenton反应后原水中的苯胺、硝基苯等物质已得到了彻底的氧化分解。     

Fenton试剂法预处理发酵甘油生产提取废水

采用Fenton试剂预处理高浓度难降解发酵法甘油生产提取废水。研究了pH、Fe^2 、H2O2、反应时间和H2O2投加次数对废水COD去除效果的影响。结果表明，通过Fenton试剂氧化可使废水中的COD值从13500mg／L降至4030mg／L，COD去除率达到70．1％。废水的BOD5／COD值从0．202提高至0．568，可生化性得到较大提高，为后续处理创造了条件。研究成果为发酵法甘油生产提取废水的预处理提供了一种非常有效的方法。     

混凝-Fenton试剂氧化工艺处理机械厂洗涤废水

对某厂机械洗涤废水,采用混凝-Fenton试剂进行处理。结果表明,用聚铝（w（PAC）=5%）对废水进行絮凝沉淀,PAC最佳投加量为1.5 mL/L（废水）,絮凝后的COD去除率为29.6%;芬顿试剂最佳操作条件为：n（H2O2）∶n（Fe2＋）=5∶1,m（H2O2）∶m（COD）=2.5∶1,废水pH=5,温度为30℃,反应时间为2 h,经氧化后,COD的去除率为78.5%;经过混凝沉淀-芬顿氧化处理,COD的总去除率为84.9%,去除效果良好。     

重金属污染土壤的草酸和EDTA混合淋洗研究

采用不同浓度的草酸(oxalic acid,OX)和乙二胺四乙酸(EDTA)混合的淋洗方法研究重金属污染土壤的最佳混合淋洗方式,探讨了液固比、淋洗时间及pH对淋洗效果的影响,并分析了0.2 mol/L OX+0.2 mol/L EDTA处理前后土壤中重金属形态的变化。结果表明,采用0.2 mol/L OX+0.2 mol/L EDTA混合的淋洗法可同时去除多种重金属,且对Cu、Zn、Ni和Cr的去除率明显高于单用OX和EDTA,去除率分别为Cu 41.29%、Zn 84.73%、Ni 54.2%和Cr 66.01%。0.2mol/L OX+0.2 mol/L EDTA在液固比为5∶1、淋洗时间为4 h、pH为6时可分别达到最佳淋洗效果,且分别为Cu 62.59%、Zn 93.48%、Ni 55.95%和Cr 71.57%;Cu 50.47%、Zn 86.67%、Ni 61.53%和Cr 72.68%;Cu 44.40%、Zn 81.82%、Ni68.76%和Cr 74.93%。形态分析结果表明,0.2 mol/L OX+0.2 mol/L EDTA能较好地改变土壤中重金属形态的分布。     

Removal of heavy metals from anaerobically digested sewage sludge by isolated indigenous iron-oxidizing bacteria

The removal of heavy metals (Cr, Cu, Zn, Ni and Pb) from anaerobically digested sludge from the Yuen Long wastewater treatment plant, Hong Kong, has been studied in a batch system using isolated indigenous iron-oxidizing bacteria. The inoculation of indigenous iron-oxidizing bacteria and the addition of FeSO4 accelerated the solubilization of Cr, Cu, Zn, Ni and Pb from the sludge. pH of the sludge decreased with an increase in Fe2+ concentrations and reached a low pH of 2-2.5 for treatments receiving both bacterial inoculation and FeSO4. After 16 days of bioleaching, the following heavy metal removal efficiencies were obtained: Cr 55.3%, Cu 91.5%, Zn 83.3%, Ni 54.4%, and Pb 16.2%. In contrast, only 2.6% of Cr, 42.9% of Cu, 72.1% of Zn, 22.8% of Ni and 0.56% of Pb were extracted from the control without the bacterial inoculation and addition of FeSO4. The residual heavy metal content in the leached sludge was acceptable for unrestricted use for agriculture. The experimental results confirmed the effectiveness of using the isolated iron-oxidizing bacteria for the removal of heavy metals from sewage sludge.     

调理剂对堆肥产品重金属生物有效性的影响

城市污泥中重金属含量及其生物有效性是限制污泥农用的主要因素,因此,研究污泥堆肥化处理过程中重金属生物有效性,对污泥的农用具有重要意义。实验以城市污泥为原料,以菌菇渣和秸秆为调理剂,设置4个处理:A(污泥∶菌菇渣∶秸秆=1∶0.4∶0.025)、B(污泥∶菌菇渣∶秸秆=1∶0.3∶0.025)、C(污泥∶秸秆=1∶0.12)和D(污泥∶秸秆=1∶0.09),进行好氧堆肥实验,采用BCR顺序提取法测定各种形态的重金属,研究堆肥前后重金属形态的变化规律。结果表明,城市污泥中Cu、Ni、Pb和Cr主要以可氧化态及残渣态存在,生物有效性较低,而Zn和Cd主要以酸溶态和可还原态存在,生物有效性较高;堆肥过程显著降低了Cu、Zn、Ni和Pb的生物有效性,并改变了Cu、Zn、Ni、Pb、Cr和Cd的形态分布,使污泥中的Cu、Zn、Ni、Pb和Cd向着更稳定的可氧化态或残渣态转变;污泥经过堆肥处理后,Cu、Zn和Ni 3种重金属生物有效性关系为:ABCD,与其他处理相比,处理A残渣态的Pb和Cr增加比例较多,综合来看,处理A对重金属生物有效性的降低最为明显,重金属钝化效果最佳。     

Effect of operational parameters on heavy metal removal by electrocoagulation

In the present paper, the performance of electrocoagulation (EC) for the treatability of mixed metals (chromium (Cr), copper (Cu), lead (Pb), nickel (Ni), and zinc (Zn)) from metal plating industrial wastewater (EPW) has been investigated. The study mainly focused on the affecting parameters of EC process, such as electrode material, initial pH, distance between electrodes, electrode size, and applied voltage. The pH 8 is observed to be the best for metal removal. Fe–Fe electrode pair with 1-cm inter-electrode distance and electrode surface area of 40 cm² at an applied voltage of 8 V is observed to more efficient in the metal removal. Experiments have shown that the maximum removal percentage of the metals like Cr, Ni, Zn, Cu, and Pb are reported to be 96.2, 96.4, 99.9, 98, and 99.5 %, respectively, at a reaction time of 30 min. Under optimum conditions, the energy consumption is observed to be 51.40 kWh/m³. The method is observed to be very effective in the removal of metals from electroplating effluent.     

Electrokinetic enhancement removal of heavy metals from industrial wastewater sludge

An enhanced electrokinetic process for removal of metals (Cr, Cu, Fe, Ni, Pb, Zn) from an industrial wastewater sludge was performed. The electrokinetic experiments were conducted under a constant potential gradient (1.25 V cm(-1)) with processing fluids of tap water (TW), sodium dodecylsulfate (SDS) and citric acid (CA) for 5 days. Results showed that metal removal efficiency of heavy metals for EK-TW, EK-SDS and EK-CA systems are 11.2-60.0%, 37.2-76.5%, and 43.4-78.0%, respectively. A highest metal removal performance was found in EK-CA system. The removal priority of investigated metals from sludge by EK process was found as: Cu > Pb > Ni > Fe > Zn > Cr. The results of sequential extraction analysis revealed that the binding forms of heavy metals with sludge after electrokinetic process were highly depend upon the processing fluid operated. It was found that the binding forms of metals with sludge were changed from the more difficult extraction type (residual and sulfate fractions) to easier extraction types (exchangeable, sorbed, and organic fraction) after treatment by electrokinetic process. Results imply that if a proper treatment technology is followed by this EK process to remove metals more effectively, this treated sludge will be more beneficial for sludge utilization afterwards. Before it was reused, the risk associated with metals of more mobile forms to the environment need to be further investigated. The cost analysis was also evaluated for the investigated electrokinetic systems.     

Heavy metals in coastal wetland sediments of the Pearl River Estuary, China

Sediment quality in coastal wetlands of the Pearl River Estuary was concerned since the wetlands were used for land reclamation, aquaculture and wildlife protection, and meanwhile served as one of the main ultimate sinks for large amount of heavy metals discharged from the rapidly developing Pearl River Delta. Total concentrations of heavy metal, such as Zn, Ni, Cr, Cu, Pb, and Cd, and their chemical speciation were investigated. Results showed that the sediments were significantly contaminated by Cd, Zn and Ni with concentration ranges of 2.79-4.65, 239.4-345.7 and 24.8-122.1mg/kg, respectively. A major portion (34.6-46.8%) of Pb, Cd, and Zn was strongly associated with exchangeable fractions, while Cu, Ni and Cr were predominantly associated with organic fractions, residual, and Fe-Mn oxide. Cd and Zn would be the main potential risk and the sediment quality is no longer meeting the demand of the current wetland utilization strategies.     

Accumulation and Chemical Fractionation of Heavy Metals in Andisols after a Different, 6-year Fertilization Management (8 pp)

Goal, Scope and Background Andisols are widespread in Japan and have some special properties such as high anion exchange capacity, low bulk density, and high organic matter content, which might influence the accumulation or chemical fractionation of heavy metals. However, few such data exist in Japanese andisols. The primary objective of this study was to investigate the distribution and chemical fractions of Cu, Zn, Ni, and Cr in the soil profiles and subsequently to assess their potential environmental hazard. Materials and Methods Soil samples were taken from a field experiment conducted on Japanese andisols, which had received either swine compost or chemical fertilizers for 6 years. Concentrations of Cu, Zn, Ni, and Cr were determined for all of the obtained extract solutions by ICP-AES. Results and Discussion Considerably higher total concentrations of Cu and Zn were observed in the top 20 cm layer of the compost-amended soil, relative to the unfertilized soil, while chemical fertilizers had little effect. Application of the swine compost increased the concentrations of Cu and Zn, but not Ni and Cr, in all fractions in the top 20 cm layer. The greatest increase in the organically bound fraction (OM) Cu and dilute acid-exchangeable fraction (DAEXCH) Zn was observed. This suggests that Cu and Zn are potentially bioavailable and mobile in the andisol profiles after 6-year consecutive applications of the swine compost. On the other hand, distribution of Cu, Zn, Ni and Cr among various soil fractions was generally unaffected by chemical fertilizers. Conclusions We observed that 6-year consecutive applications of the swine compost led to an increase in total metals of Cu and Zn, as well as their all-chemical fractions, in the top 20 cm soil layers. Potential hazard of heavy metals, especially of Cu and Zn, as a result of the use of swine compost on andisols, must be taken into account. Recommendations and Outlook The long-term effect of the accumulation of heavy metals, particularly Cu and Zn, in various plant tissues and soils, as well as their potential risk to surface water via runoff and groundwater via leaching, needs to be carefully considered. Further investigations in the long-term experiments are therefore necessary. - Abbreviations. EXCH, exchangeable fraction of metals; DAEXCH, dilute acid-exchangeable fraction of metals; FeMnOX, iron and manganese-oxide-bound fraction; OM, organically-bound fraction; RESD, residual fraction. COMPOST, SRNF, RANF, and CONTROL stand for compost (from swine wastes), slow-release nitrogen fertilizer (coated urea), readily available nitrogen fertilizer (including NH4-N, P, and K fertilizers), and no fertilizer application, respectively.     

巢湖表层沉积物中重金属的分布特征及其污染评价

以巢湖表层沉积物为研究对象,利用BCR连续提取法研究了沉积物中Cr、Co、Ni、Cu、Cd、Zn、V和Pb等8种重金属元素的分布特征,同时运用潜在风险指数法和地累积指数法综合评价了巢湖沉积物中重金属的生态风险。结果表明,巢湖沉积物中的重金属含量在空间上表现出东西高、中间低的分布特征。巢湖表层沉积物中Cr、Co、Ni、V和Cu 5种重金属都主要以残渣态为主,Zn和Cd主要以弱酸提取态为主,Pb以可还原态为主,同时,Co和Cu 2种元素的可交换态及可还原态含量占有较高比例,具有潜在危害性。相关性分析显示,Cr、Cu、Pb、Ni、Zn和Cd 6种重金属元素的来源和分布可能具有相似性,Co和V 2种重金属元素具有相似的地球化学行为且其主要来源可能与其他几种重金属不同。潜在生态风险指数评价结果表明,巢湖表层沉积物中8种重金属元素构成的生态危害顺序为:Cd>Pb>Co>Cu>Ni>Zn>V>Cr,Cd具有高的生态危害等级,其他7种重金属元素均为低生态危害等级。地累积指数法评价结果表明:巢湖沉积物重金属元素的富集程度为Cd>Zn>Pb>Co>Cu>V>Ni>Cr,Cr属于清洁级别,Co、Cu、V和Ni处于轻度污染水平,Zn和Pb处于偏中度污染,Cd达到了重污染水平。     

The use of a sequential leaching procedure for heavy metal fractionation in green liquor dregs from a causticizing process at a pulp mill

A five-stage sequential leaching procedure was used to fractionate heavy metals (Cd, Cu, Pb, Cr, Zn, Fe, Mn, Ni, Co, As, V, Ba and Ti) in green liquor dregs into the following fractions: (1) water-soluble fraction (H2O), (2) exchangeable fraction (CH3COOH), (3) easily reduced fraction (HONH3Cl), (4) oxidizable fraction (H2O2 + CH3COONH4), and (5) residual fraction (HF + HNO3 + HCl). The green liquor dregs were derived from a causticizing process at a pulp mill at Kemi, Northern Finland. According to the leaching studies, the leachability of heavy metals in the water-soluble fraction varied between 0.5 and 2 mg kg(-1) expressed on a dry weight (d.w.) basis, indicating relatively low bioavailability of the metals. However, the concentration of Mn (2065 mg kg(-1); d.w.) showed a strong and of Zn (17.6 mg kg(-1); d.w.), Ni (39.7 mg kg(-1); d.w.) and Ba (32.0 mg kg(-1); d.w.) slightly tendency to be extracted in the exchangeable fraction. In addition, Zn, Mn, Ni, Co, V and Ba showed clear leachability in the easily reduced fraction, as well as Cd, Cu, Cr, Zn, Mn, As and Ba in the oxidizable fraction. For Cd, Cu, Cr, Zn, Mn, Ni, Co, Ba and Ti, the sum of leachable heavy metal concentrations in fractions 1-5 agreed relatively well with the "total" heavy metal concentrations. Recoveries of the sum of fractions 1-5 were 84-56% of those obtained by the US EPA method 3052 (i.e. concentrations obtained after microwave oven digestion with a mixture of HF and HNO3).