Rapid multiresidue determination for currently used pesticides in agricultural drainage waters and soils using gas chromatography–mass spectrometry

An efficient and sensitive method for simultaneous determination of 38 pesticides in agricultural drainage waters and soils has been developed and validated. Water samples were extracted using solid-phase extraction with C18 cartridges while solid samples (suspended particle matter and soil) were extracted by using the quick, easy, cheap, effective, rugged and safe (QuEChERS) extraction method. The target pesticides were analyzed by using gas chromatography-mass spectrometry with electron impact ionization. The proposed method allowed a simultaneous determination and confirmation of a large number of pesticides in agricultural drainage waters, suspended particle matters and soils/sediments with a good reproducibility and low detection limits. The developed method was applied to a survey of pesticides in a vegetable growing area of Guangzhou, China. The pesticides commonly found in the area were butachlor, carbofuran, dichlorvos, fipronil, isocarbophos and pyridaben.     

Validation and application of an analytical method for determining pesticides in the gas phase of ambient air

A method for determining atmospheric concentrations of eight pesticides applied to corn and soybean crops in Mato Grosso state, Brazil is presented. The method involved a XAD-2 resin cartridge coupled to a low volume air pump at 2 L min^?1 over 8 hours. Pesticides were recovered from the resin using sonication with n-hexane:ethyl acetate and determined by GC-MS. Good accuracy (76–128%) and precision (CV < 20%) were obtained for atrazine, chlorpyrifos, alpha- and beta-endosulfan, endosulfan sulfate, flutriafol, malathion, metolachlor and permethrin. Method detection ranged from 9.0 to 17.9 ng m^?3. This method was applied to 61 gas phase samples collected between December 2008 and June 2009. Atrazine and endosulfan were detected both in urban and rural areas indicating the importance of atmospheric dispersion of pesticides in tropical areas. The simple and efficient extraction method and sampling system employed was considered suitable for identifying pesticides in areas of intense agricultural production.     

Evaluation of pressurized liquid extraction for determination of organophosphorus and pyrethroid pesticides in soybean

The purpose of this study was to develop an analytical method for the determination of organophosphorus and pyrethroid pesticides in soybean by pressurized liquid extraction (PLE). Two organic solvents, acetone and acetonitrile, were evaluated as extraction solvents. In both cases, the amount of extract was enhanced with increasing extraction temperature. The extracts obtained using acetonitrile were measured by gas chromatography/mass spectrometry after a cleanup process based on the analytical method for the Japanese Positive List System for Agricultural Chemicals Remaining in Foods. The effect of extraction temperature (range: 40– 130°C) on extraction efficiency was evaluated by a recovery study using 21 organophosphorus pesticides and 10 pyrethroid pesticides as target analytes and acetonitrile as the solvent. The results indicated that at 130°C, some organophosphorus pesticides might be degraded, whereas extraction temperatures between 70°C and 100°C were optimal. Next, a prepared sample containing fenitrothion and permethrin was analyzed. Although the sample was not soaked in water prior to analysis, PLE provided analytical results comparable to those obtained by solvent extraction with homogenization. Therefore, PLE is considered a simple and alternative technique for the extraction of organophosphorus and pyrethroid pesticides in soybean.     

Evaluation of pressurized liquid extraction for determination of organophosphorus and pyrethroid pesticides in soybean

The purpose of this study was to develop an analytical method for the determination of organophosphorus and pyrethroid pesticides in soybean by pressurized liquid extraction (PLE). Two organic solvents, acetone and acetonitrile, were evaluated as extraction solvents. In both cases, the amount of extract was enhanced with increasing extraction temperature. The extracts obtained using acetonitrile were measured by gas chromatography/mass spectrometry after a cleanup process based on the analytical method for the Japanese Positive List System for Agricultural Chemicals Remaining in Foods. The effect of extraction temperature (range: 40- 130°C) on extraction efficiency was evaluated by a recovery study using 21 organophosphorus pesticides and 10 pyrethroid pesticides as target analytes and acetonitrile as the solvent. The results indicated that at 130°C, some organophosphorus pesticides might be degraded, whereas extraction temperatures between 70°C and 100°C were optimal. Next, a prepared sample containing fenitrothion and permethrin was analyzed. Although the sample was not soaked in water prior to analysis, PLE provided analytical results comparable to those obtained by solvent extraction with homogenization. Therefore, PLE is considered a simple and alternative technique for the extraction of organophosphorus and pyrethroid pesticides in soybean.     

Validation of a GC-MS/MS method for simultaneous determination of 86 persistent organic pollutants in marine sediments by pressurized liquid extraction followed by stir bar sorptive extraction

A multiresidue method for the analysis of 86 persistent pollutants in marine sediments at ultra-trace level has been developed and validated using pressurized liquid extraction (PLE) and stir-bar sorptive extraction (SBSE) coupled with thermal desorption and gas chromatography-triple quadrupole mass spectrometry (TD-GC-MS/MS QqQ). The compounds analyzed belong to various families such as polychlorinated biphenyls, polycyclic aromatic hydrocarbons, polybrominated diphenylethers, organophosphorus and organochlorine pesticides and other pesticides such as urons, and triazines. The analytes have very different polarities and log K_ow values, which is an important parameter in the optimization of a SBSE method. Due to PLE high efficiency and throughput rates, along with the proven ability for multiresidue analysis and excellent sensitivity of SBSE, we present an efficient method. The limits of quantification obtained ranged from 0.014 to 1.0 ng g⁻¹, with detection limits below pg g⁻¹ levels. In order to validate the proposed methodology, quality parameters such as recovery, linearity and reproducibility were studied. Recoveries ranged from 63% to 119%, reproducibility (in terms of Relative Standard Deviation for ten determinations) was lower than 35% in all cases, and determination coefficients higher than 0.990 for all analytes. The main factors that affect PLE, SBSE and GC-MS/MS procedures were optimized. The method was applied to the analysis of nine marine sediments obtained from the nine main submarine wastewater discharge points (emissaries) presents along the coast of Tenerife Island (Canary Islands, Spain).     

Evaluation of pressurized liquid extraction for the determination of neonicotinoid pesticides in green onion

Abstract

A pressurized liquid extraction (PLE) method was presented for the determination of six neonicotinoid pesticides, acetamiprid, clothianidin, dinotefuran, imidacloprid, thiacloprid, and thiamethoxam in green onion. The critical parameters of PLE, e.g. extraction solvent, temperature, pressure, number of cycles, and static extraction time, were optimized by test on the spiked green onion with six neonicotinoids and the incurred green onion applied with four commercial neonicotinoid insecticide formulations (acetamiprid, dinotefuran, imidacloprid, and thiamethoxam). As a result, the recoveries of six neonicotinoids obtained by one cycle PLE with acetonitrile at 140?°C and 50?bar for 10?min were 94.7–99.5%. These results were acceptable according to the validation guideline for testing method of agricultural chemicals in food by Ministry of Health, Labour, and Welfare in Japan. PLE was also validated by the test on the incurred green onion. The analytical values of four neonicotinoids obtained by PLE were good agreement with those obtained by solid–liquid extraction with homogenizer, which is employed for Japanese official method for the analysis of pesticide residues in food (the ratios of analytical values obtained by PLE to those obtained by solid–liquid extraction were 99.7–101.2%). These results indicate that PLE is applicable for the determination of neonicotinoids in green onion.     

Method for the determination of selected organochlorine pesticides and polychlorinated biphenyls in human serum based on a gel permeation chromatographic clean-up

A gel permeation chromatographic (GPC) clean-up based method was developed for determination of selected organochlorine pesticides and polychlorinated biphenyls in human serum. The method permits automation of the sample extract clean-up stage and is designed to work with small amounts of sample. Different working variables were studied in its development, including injection volume, flow rate, and fat amount as the most representative coextract. The method provides solvent and time savings. Initial extraction was performed using 96-well solid-phase disk extraction plates, and quantification was performed by gas chromatography with electron capture detection and mass spectrometry. Recoveries of PCB congeners 28, 52, 101, 118, 138, 153, and 180 and organochlorine pesticides HCB, β-HCH, γ-HCH, heptachlor epoxide, p,p′-DDE, and p,p′-DDT at two spiking levels ranged from 55% to 115% with relative standard deviations ranging from 2.0% to 14.6%. Limits of quantification ranged from 0.06 to 0.16 ng mL⁻¹ for PCBs and from 0.12 to 0.36 ng mL⁻¹ for organochlorine pesticides. Finally, the method was applied to the analysis of 38 serum samples and the results were compared with those of another procedure validated at the laboratory.     

A method for the analysis of organophosphorus pesticide residues in Mexican axolotl

A method based on matrix solid-phase dispersion (MSPD) was developed for quantitative extraction of three organophosphorus pesticides (OPPs) from the Mexican axolotl, Ambystoma mexicanum. The determination was carried out using high- performance liquid chromatography (HPLC) with diode array spectrophotometric UV detection (DAD). The MSPD extraction with octadecylsilyl (C18) sorbent combined with a silica gel clean-up and acetonitrile elution was optimised for chlorpyrifos, fenthion and methyl parathion. The method was validated, yielding recovery values higher than 90%. The precision, expressed as the relative standard deviation (RSD), was less than or equal to 6% in muscle samples at spiking levels of 10 and 5 ppm. Linearity was studied from 15 to 60 ppm for chlorpyrifos and fenthion, and from 7.5 to 30 ppm for methyl parathion. The limits of detection (LODs) were found to be less than or equal to 0.5 ppm_.This method was applied to the analysis of samples from a chlorpyrifos-exposed axolotl, demonstrating its use as an analytical tool for toxicological studies.     

Application of automated mass spectrometry deconvolution and identification software for pesticide analysis in surface waters

A new approach to surface water analysis has been investigated in order to enhance the detection of different organic contaminants in Nathan Creek, British Columbia. Water samples from Nathan Creek were prepared by liquid/liquid extraction using dichloromethane (DCM) as an extraction solvent and analyzed by gas chromatography mass spectrometry method in scan mode (GC-MS scan). To increase sensitivity for pesticides detection, acquired scan data were further analyzed by Automated Mass Spectrometry Deconvolution and Identification Software (AMDIS) incorporated into the Agilent Deconvolution Reporting Software (DRS), which also includes mass spectral libraries for 567 pesticides. Extracts were reanalyzed by gas chromatography mass spectrometry single ion monitoring (GC-MS-SIM) to confirm and quantitate detected pesticides. Pesticides: atrazine, dimethoate, diazinone, metalaxyl, myclobutanil, napropamide, oxadiazon, propazine and simazine were detected at three sampling sites on the mainstream of the Nathan Creek. Results of the study are further discussed in terms of detectivity and identification level for each pesticide found. The proposed approach of monitoring pesticides in surface waters enables their detection and identification at trace levels.     

Rapid determination of residues of pesticides in honey by µGC-ECD and GC-MS/MS: Method validation and estimation of measurement uncertainty according to document No. SANCO/12571/2013

A simple and straightforward method for simultaneous determination of residues of 13 pesticides in honey samples (acrinathrin, bifenthrin, bromopropylate, cyhalothrin-lambda, cypermethrin, chlorfenvinphos, chlorpyrifos, coumaphos, deltamethrin, fluvalinate-tau, malathion, permethrin and tetradifon) from different pesticide classes has been developed and validated. The analytical method provides dissolution of honey in water and an extraction of pesticide residues by n-Hexane followed by clean-up on a Florisil SPE column. The extract was evaporated and taken up by a solution of an injection internal standard (I-IS), ethion, and finally analyzed by capillary gas chromatography with electron capture detection (GC-µECD). Identification for qualitative purpose was conducted by gas chromatography with triple quadrupole mass spectrometer (GC-MS/MS). A matrix-matched calibration curve was performed for quantitative purposes by plotting the area ratio (analyte/I-IS) against concentration using a GC-µECD instrument. According to document No. SANCO/12571/2013, the method was validated by testing the following parameters: linearity, matrix effect, specificity, precision, trueness (bias) and measurement uncertainty. The analytical process was validated analyzing blank honey samples spiked at levels equal to and greater than 0.010 mg/kg (limit of quantification). All parameters were satisfactorily compared with the values established by document No. SANCO/12571/2013. The analytical performance was verified by participating in eight multi-residue proficiency tests organized by BIPEA, obtaining satisfactory z-scores in all 70 determinations. Measurement uncertainty was estimated according to the top-down approaches described in Appendix C of the SANCO document using the within-laboratory reproducibility relative standard deviation combined with laboratory bias using the proficiency test data.     

Determination of pharmaceuticals, personal care products, and pesticides in surface and treated waters: method development and survey

Water is fundamental to the existence of life since it is essential to a series of activities, such as agriculture, power generation, and public and industrial supplies. The residual water generated by these activities is released into the environment, reaches the water systems, and becomes a potential risk to nontarget organisms. This paper reports the development and validation of a quantitative method, based on solid-phase extraction and liquid chromatography tandem mass spectrometry, for the simultaneous analysis of 18 pharmaceuticals and personal care products (PPCPs) and 33 pesticides in surface and drinking waters. The accuracy of the method was determined by calculating the recoveries, which ranged from 70 to 120 % for most pesticides and PPCPs, whereas limits of quantification ranged from 0.8 to 40 ng/L. After the validation step, the method was applied to drinking and surface waters. Pesticides and PPCPs were found in concentrations lower than 135.5 ng/L. The evaluation of different water sources with regard to contamination by pesticides and PPCPs has been quite poor in southern Brazil.     

Adsorption/thermal desorption-GC/MS for the analysis of pesticides in the atmosphere

An analytical methodology using Automatic Thermal Desorption (ATD) and GC/MS was developed for the determination of the pesticides alachlor, atrazine, captan, formothion, lindane and phosalone in atmospheric samples. This methodology was developed to evaluate the atmospheric contamination by pesticides during treatments and by post-application. Atmospheric samples were collected by using (4 i.d. x 89 mm) stainless steel sampling tubes containing 125 mg of adsorbents at a flow rate of 80 ml min-1. Different types of adsorbents were tested for their ability to efficiently trap pesticides under study: Tenax TA, Carbopack Y, Carbopack B, Carbotrap, Carboxen, Chromosorb 106 and XAD-4. Results of experiment show that Tenax gives the better results for all the pesticides used but the use of the thermal-desorption method, especially for pesticides with low volatility and/or poor thermal stability presents some difficulties. This method was validated by the analysis of the contamination of atmosphere, through volatilization by post-application processes, of atrazine in a parcel of 1 ha.     

A method to determine residue levels of persistent organochlorine pesticides in human milk from Indonesian women

A method has been developed for the analysis of organochlorine pesticides in human milk using solvent extraction, Florisil solid phase extraction clean-up and analysis by gas chromatography with an electron capture detector. The recovery of analytes from spiked milk samples was in the range 53 +/- 1% to 109 +/- 7% (n = 9). A small number of samples were obtained from women in a rural and an urban area of Indonesia and analysed using the developed method. The results are reported on a milk fat basis. All samples contained detectable residues of p,p'-DDT (urban mean 0.11 +/- 0.18 mgkg(-1) (n = 5), rural mean 0.07 +/- 0.03 mg kg(-1) (n = 5)) and p,p'-DDE (urban mean 0.05 +/- 0.04 m kg(-1) (n = 5), rural mean 0.76 +/- 1.46 mg kg(-1) (n = 5)). Residues of HCB, betaHCH, alpha-endosulfan and dieldrin were also detected in some samples. There was no significant difference (at the 95% confidence level) in levels of pesticides between urban and rural areas. The levels of organochlorine pesticides in milk from Indonesian women were lower than those reported from Indonesian women exposed to DDT through malaria eradication schemes and were similar to levels reported from UK and Japan.     

Application of Automated Mass Spectrometry Deconvolution and Identification Software for Pesticide Analysis in Surface Waters

A new approach to surface water analysis has been investigated in order to enhance the detection of different organic contaminants in Nathan Creek, British Columbia. Water samples from Nathan Creek were prepared by liquid/liquid extraction using dichloromethane (DCM) as an extraction solvent and analyzed by gas chromatography mass spectrometry method in scan mode (GC-MS scan). To increase sensitivity for pesticides detection, acquired scan data were further analyzed by Automated Mass Spectrometry Deconvolution and Identification Software (AMDIS) incorporated into the Agilent Deconvolution Reporting Software (DRS), which also includes mass spectral libraries for 567 pesticides. Extracts were reanalyzed by gas chromatography mass spectrometry single ion monitoring (GC-MS-SIM) to confirm and quantitate detected pesticides. Pesticides: atrazine, dimethoate, diazinone, metalaxyl, myclobutanil, napropamide, oxadiazon, propazine and simazine were detected at three sampling sites on the mainstream of the Nathan Creek. Results of the study are further discussed in terms of detectivity and identification level for each pesticide found. The proposed approach of monitoring pesticides in surface waters enables their detection and identification at trace levels.     

Evaluation of a multiresidue method for pesticides in cereals using supercritical fluid extraction and gas chromatographic detection

Supercritical fluid extraction (SFE) was evaluated to be applied for residue analysis of 22 gas chromatography/electron capture detector-nitrogen phosphorus detector (GC/ECD-NPD) amenable pesticides in rice, wild rice and wheat. Samples were extracted with supercritical carbon dioxide at 200 atm pressure and 50°C temperature, using methanol as a static modifier. Mean recoveries obtained with the proposed SFE method at two spiking levels with four replicates per level are compared with those obtained with an ethyl acetate-based solvent extraction/gel permeation chromatography (GPC) clean up method. Both methods gave consistent high recoveries for almost all the pesticides from all the commodities with overall mean recoveries higher than 70% with relative standard deviations lower than 20%. Remarkable exceptions were captafol and dimethoate, for which low and/or non-reproducible recoveries were obtained with the SFE method. Residue levels determined with both methods in nine different incurred samples of wheat, containing some of the studied pesticides, were very similar, but, in all cases, slightly higher levels were determined with the SFE method.     

Multiresidue analysis and monitoring of pesticides in rice by pressurized liquid extraction

The aim of this study was to assess the performance of a method of analyzing pesticides in rice by using pressurized liquid extraction (PLE) and to perform a preliminary monitoring by using that method. The instrumental quantification limit, instrumental detection limit, method quantification limit, and method detection limit were determined. PLE temperature was also optimized for 6 target pesticides. Mean recoveries of spiked rice with target pesticides (4 ng/g and 40 ng/g) were 83%–109% with the repeatability of the analysis, represented as relative standard deviations, ranged from 1.3% to 11% (n = 5) for PLE at 130°C. These results were satisfactory according to the method of positive list in Japan. In a preliminary analysis of 10 target pesticides in 54 commercial rice samples, ferimzone was detected in only one unpolished rice sample.     

Determination of 10 particle-associated multiclass polar and semi-polar pesticides from small streams using accelerated solvent extraction

A new analytical method using accelerated solvent extraction was developed for the determination of 10 particle-associated polar and semipolar pesticides. In addition, six deuterated analogues of the target compounds were evaluated as internal standards. The method yielded acceptable accuracy (73–103% recovery) and precision (<25% relative standard deviation) for eight compounds. Using size exclusion chromatography (SEC) as cleanup step resulted in higher recoveries compared to solid phase extraction (SPE) cleanup.

Deuterated standards with 10 or more deuterium atoms performed well as internal standards concerning similar recovery and correlation with the target analytes.

The method was employed to extract particle-associated pesticides from 16 streams located in an area with intense agriculture in France. Acetochlor, pirimicarb, tebuconazole, fenpropidin, -endosulfan and chlorfenvinphos were detected at concentrations up to 1 mg kg⁻¹ dry weight. A comparison with aquatic toxicity data indicated potential risk to the benthic fauna exposed to these concentrations of pirimicarb, -endosulfan and chlorfenvinphos.

We suggest that the method presented here be used for the extraction and quantitation of particle-associated polar pesticides.     

Validation of an efficient method for the determination of pesticide residues in fruits and vegetables using ethyl acetate for extraction

In this study, a version of the "quick, easy, cheap, effective, rugged, and safe" (QuEChERS) method was modified to use ethyl acetate (EtOAc) rather than acetonitrile (MeCN) for extraction in the determination of multiple pesticide residues in fruits and vegetables. EtOAc is better suited than MeCN for gas chromatographic (GC) analysis with electron capture detection (ECD) and nitrogen-phosphorus detection (NPD). The method entailed extraction of 30 g chopped sample plus 5 g NaHCO(3) and 30 g anhydrous Na(2)SO(4) with 60 mL EtOAc using a probe blender. After a centrifugation step, removal of residual water and cleanup were performed using dispersive solid-phase extraction (dispersive-SPE) with MgSO(4) and primary secondary amine (PSA) sorbent. (14)C-labeled chlorpyrifos with liquid scintillation counting was used to assist in optimizing and characterizing the method, and GC-ECD and GC-NPD were used for analysis of 24 selected pesticides. The method was validated using tomato, apple and frozen green bean matrices spiked at 0.05, 0.5, and 5 mg/kg. For 22 of the analytes, recoveries averaged 93% for all three commodities over the validation range with a relative standard deviation of 10% (n = 1182). Lower recoveries of dichlorvos were obtained with the method and iprodione determination was compromised in the green beans by an interfering peak. Typical limits of detection were 0.005-0.01 mg/kg with the method.     

Comparative study of accessibility of distinctive pesticides

Interactions of micro-contaminants with soil may play a crucial role in their environmental fate and possible harmful effects. Major goals of our investigations were to model the availability of widely used pesticides and characterize adsorption capabilities of distinctive soil types by the accomplishment of extensive comparative studies and application of several extraction methods. Environmental and biological relevance of these examinations is enhanced by the fact that intrinsic features and specific details of pesticide accessibility have not been revealed so far by a comparative approach. Five different experimental methods were assessed for modelling accessibility of five selected pesticides. The applied models for regaining the pesticides showed diverse efficiency in extraction capability in cases of the different soil types (sandy, brown forest and alluvial soils). The amounts of the obtained pesticides were determined by using gas-chromatography coupled to mass spectrometry (GC-MS) and high pressure liquid chromatography coupled to mass spectrometry (HPLC-MS). Accessibility of pesticides was also compared in cases of sterilized and real soil samples in order to estimate the extent of the influence of microflora. Aqueous extraction solvents proved to be suitable for accurate assessment of the accessible amounts of pesticides, as their effectivity was at least as high as that of the applied organic solvents. In our studies pesticide-soil interactions have comprehensively been characterized, and possible influences of environmental factors on the accessibility have also been revealed. Our study might be regarded as a tentative approach to model some significant circumstances playing key roles in pesticides' possible bioavailability.     

Multicriteria optimisation of a simultaneous supercritical fluid extraction and clean-up procedure for the determination of persistent organohalogenated pollutants in aquaculture samples

A useful tool based on a single-step extraction and clean-up procedure for the determination of 15 organohalogenated pollutants (including brominated flame retardants) in aquaculture samples, using aluminium oxide basic and acidic silica gel in the supercritical extraction cell followed by gas chromatography with electron capture detection or mass spectrometry has been developed. This effective clean-up step ensures a minimum of chromatographic difficulties related to complex matrix components such as aquaculture feed. The extraction procedure has been screened by a fractional factorial design for the preliminary statistically significant parameters. The factors selected were extraction temperature, pressure, static extraction time, dynamic extraction time and carbon dioxide flow rate. The Doehlert design, followed by a multicriteria decision-making strategy, was then performed in order to determine the optimum conditions for the two most significant factors: pressure (165 bar) and dynamic extraction time (27 min). Under optimal conditions, the procedure developed with GC-MS/MS provides an excellent linearity, detection (0.01-0.2 ng g(-1)) and quantification limits (0.05-0.8 ng g(-1)) for most of the analytes investigated. The feasibility of the proposed supercritical fluid extraction method was validated by analysing two reference materials and fish feed and shellfish samples with satisfactory results.