The effects of manganese precursors on Mn-based/TiO2 catalysts for catalytic reduction of NO with NH3

Manganese acetate (MnAc) and manganese nitrate (MnN) were employed as precursors for the preparation of MnAc)/TiO2, Mn (N)/TiO2, Mn(Ac)-Ce/TiO2, and Mn(N)-Ce/TiO2 by impregnation. These complexes were used as catalysts in the low-temperature selective catalytic reduction of NO with NH3. The influence of manganese precursors on catalyst characteristics, the reduction activity, and the stability of the catalysts to poisoning by H2O and SO2 were studied. Experiments showed that Mn(N) produced MnO2 with large grain sizes in Mn(N)/TiO2 catalyst. On the contrary, Mn(Ac) led to highly dispersed and amorphous Mn2O3 in Mn (Ac)/TiO2 catalyst, which had better catalytic activity and stability to SO2 at low temperatures. The doping of cerium reduced the differences in catalytic performance between the catalysts derived from different Mn precursors.     

A study on the reaction characteristics of vanadium-impregnated natural manganese oxide in ammonia selective catalytic reduction

This study investigated the effect of adding vanadium (V) to natural manganese oxide (NMO) in ammonia (NH3) selective catalytic reduction (SCR). The addition of V to NMO decreased the catalytic activity at low temperatures by blocking the active site. However, the enhancement of catalytic activity was achieved by controlling NH3 oxidation at high temperatures. From the NH3 temperature programmed desorption and oxygen on/off test, it was confirmed that the amount of Lewis acid site and active lattice oxygen of the catalyst affects the catalytic performance at low temperature.     

Size Distribution of Particles That May Contribute to Soiling of Material Surfaces

ABSTRACT

This study investigated the effect of adding vanadium (V) to natural manganese oxide (NMO) in ammonia (NH₃) selective catalytic reduction (SCR). The addition of V to NMO decreased the catalytic activity at low temperatures by blocking the active site. However, the enhancement of catalytic activity was achieved by controlling NH₃ oxidation at high temperatures. From the NH₃ temperature programmed desorption and oxygen on/off test, it was confirmed that the amount of Lewis acid site and active lattice oxygen of the catalyst affects the catalytic performance at low temperature

IMPLICATIONS Recently, NMO and manganese oxide have been reported as SCR catalysts. They usually have only reported the reaction characteristics and catalytic activity on the NH₃ SCR over NMO or manganese/metal oxide catalysts. There are no studies about the effect of addition of V to NMO. Therefore, this study investigates the catalytic activity and reaction characteristics on the NH₃ SCR over NMO and V/NMO, and a new application is proposed based on the conclusions of this study.     

Ti-Ce-Zr-Ox复合脱硝催化剂的制备及其性能研究

采用共混法制备了Ti-Ce-Zr-Ox复合脱硝催化剂TiCe0.1Zr0.1O2.4,运用X射线衍射、氮气物理吸附、扫描电镜等表征手段,分别对该催化剂的晶型、表面积、孔分布及结构形貌进行了分析,同时考察了反应温度、空速、水蒸气和SO2对该催化剂NH3选择性催化还原NO的影响.结果表明,TiCe0.1Zr0.1O2.4催...     

Catalytic wet oxidation of ammonia: why is N2 formed preferentially against NO3 -?

The role of catalyst and the reason for the preferential formation of N(2) in the catalytic oxidation reaction of ammonia in water over a Ru (3wt.%)/TiO(2) catalyst were elucidated. It was verified that the catalyst in the reaction had no direct relevance to the selective formation of N(2), but was responsible only for the oxidation of aqueous ammonia, NH(3)(aq), finally giving a molecule of nitrous acid. The preferential production of N(2) was experimentally demonstrated due to the homogeneous aqueous phase reaction of the nitrous acid-dissociated NO(2)(-) with NH(4)(+) ions. Even under the highly oxidizing condition, NO(2)(-) was much more likely to react with NH(4)(+) to form N(2) than being oxidized over the catalyst to NO(3)(-) as long as NH(4)(+) was available in solution.     

Structure of Mn-Zr mixed oxides catalysts and their catalytic performance in the gas-phase oxidation of chlorocarbons

The catalytic activity and selectivity of manganese zirconia mixed oxides were evaluated for the oxidation of two common chlorinated pollutants found in waste streams, namely 1,2-dichloroethane (DCE) and trichloroethylene (TCE). Mixed oxides with varying Mn-Zr content were prepared by coprecipitation via nitrates, and subsequent calcination at 600 degrees C for 4 h in air. These catalysts were characterised by means of several techniques such as atomic emission spectrometry, N2 adsorption-desorption, powder X-ray diffraction, temperature-programmed desorption of ammonia, pyridine adsorption followed by diffuse reflectance infrared spectroscopy and temperature-programmed reduction with hydrogen. The active catalytic behaviour of Mn-Zr mixed oxides was ascribed to a substantial surface acidity combined with readily accessible active oxygen species. Hence, the mixed oxide with 40 mol% manganese content was found to be an optimum catalyst for the combustion of both chlorocarbons with a T50 value around 305 and 315 degrees C for DCE and TCE oxidation, respectively. The major oxidation products were carbon dioxide, hydrogen chloride and chlorine. It was observed that the formation of both CO2 and Cl2 was promoted with Mn loading.     

Effect of the Mn oxidation state and lattice oxygen in Mn-based TiO2 catalysts on the low-temperature selective catalytic reduction of NO by NH3

TiO₂-supported manganese oxide catalysts formed using different calcination temperatures were prepared by using the wet-impregnation method and were investigated for their activity in the low-temperature selective catalytic reduction (SCR) of NO by NH₃ with respect to the Mn valence and lattice oxygen behavior. The surface and bulk properties of these catalysts were examined using Brunauer-Emmett-Teller (BET) surface area, X-ray diffraction (XRD), temperature-programmed reduction (TPR), and temperature-programmed desorption (TPD). Catalysts prepared using lower calcination temperatures, which contained Mn⁴⁺, displayed high SCR activity at low temperatures and possessed several acid sites and active oxygen. The TPD analysis determined that the Brönsted and Lewis acid sites in the Mn/TiO₂ catalysts were important for the low-temperature SCR at 80～160 and 200～350 °C, respectively. In addition, the available lattice oxygen was important for attaining high NO to NO₂ oxidation at low temperatures.

Implications: Recently, various Mn catalysts have been evaluated as SCR catalysts. However, there have been no studies on the relationship of adsorption and desorption properties and behavior of lattice oxygen according to the valence state for manganese oxides (MnO_x). Therefore, in this study, the catalysts were prepared by the wet-impregnation method at different calcination temperatures in order to show the difference of manganese oxidation state. These catalysts were then characterized using various physicochemical techniques, including BET, XRD, TPR, and TPD, to understand the structure, oxidation state, redox properties, and adsorption and desorption properties of the Mn/TiO₂ catalysts.     

Removal of nitrogenous compounds by catalytic wet air oxidation. Kinetic study

Aqueous wastes containing organic pollutants can be efficiently treated by wet air oxidation (WAO), i.e. oxidation by molecular oxygen in the liquid phase, under high temperature (200-325 degrees C) and pressure (up to 150 bar). However, organic nitrogen can be relatively resistant to oxidation and can be harmful to the environment. In the course of treatment, organic nitrogen (N-Org) is converted into ammonia (NH(3)), while organic carbon (C-Org) is converted mainly into carbon dioxide (CO(2)). This can be done without catalysts. In the presence of Mn/Ce composite oxides, it is possible to transform ammonia into molecular nitrogen at a temperature close to 260 degrees C. The direct conversion of organic nitrogen into molecular nitrogen also can be achieved using the same catalyst. This paper discusses the results obtained during the treatment of nitrogenous compounds like aniline, nitrophenol, beta-alanine and ammonia. Laboratory investigations were conducted in a stirred batch reactor with Mn/Ce composite oxides as catalysts. Very limited amounts of nitrites and nitrates were observed with amines, but more significant quantities were found with nitro-compounds. The kinetics of oxidation of ammonia, organic compounds, and more particularly aniline, were investigated. The treatment of a real waste (process wastewater) was also investigated. The dependence of the transformation rate on various parameters (amount of catalyst, temperature, etc.) was established. The rates of oxidation are described by first-order kinetic laws with respect to the various nitrogen species (aniline, NH(3)). Several parallel pathways are considered for the transformation of organic nitrogen, amongst which is an interaction with the catalyst surface. The orders with respect to oxygen and catalyst are established.     

A predictive mechanism for mercury oxidation on selective catalytic reduction catalysts under coal-derived flue gas

This paper introduces a predictive mechanism for elemental mercury (Hg(o)) oxidation on selective catalytic reduction (SCR) catalysts in coal-fired utility gas cleaning systems, given the ammonia (NH3)/nitric oxide (NO) ratio and concentrations of Hg(o) and HCl at the monolith inlet, the monolith pitch and channel shape, and the SCR temperature and space velocity. A simple premise connects the established mechanism for catalytic NO reduction to the Hg(o) oxidation behavior on SCRs: that hydrochloric acid (HCl) competes for surface sites with NH3 and that Hg(o) contacts these chlorinated sites either from the gas phase or as a weakly adsorbed species. This mechanism explicitly accounts for the inhibition of Hg(o) oxidation by NH3, so that the monolith sustains two chemically distinct regions. In the inlet region, strong NH3 adsorption minimizes the coverage of chlorinated surface sites, so NO reduction inhibits Hg(o) oxidation. But once NH3 has been consumed, the Hg(o) oxidation rate rapidly accelerates, even while the HCl concentration in the gas phase is uniform. Factors that shorten the length of the NO reduction region, such as smaller channel pitches and converting from square to circular channels, and factors that enhance surface chlorination, such as higher inlet HCl concentrations and lower NH3/NO ratios, promote Hg(o) oxidation. This mechanism accurately interprets the reported tendencies for greater extents of Hg(o) oxidation on honeycomb monoliths with smaller channel pitches and hotter temperatures and the tendency for lower extents of Hg(o) oxidation for hotter temperatures on plate monoliths. The mechanism also depicts the inhibition of Hg(o) oxidation by NH3 for NH3/NO ratios from zero to 0.9. Perhaps most important for practical applications, the mechanism reproduces the reported extents of Hg(o) oxidation on a single catalyst for four coals that generated HCl concentrations from 8 to 241 ppm, which covers the entire range encountered in the U.S. utility industry. Similar performance is also demonstrated for full-scale SCRs with diverse coal types and operating conditions.     

温度变化对厌氧氨氧化反应的影响

对一套处理效率高、运行稳定的UASB．生物膜厌氧氨氧化反应器进行了温度变化的实验研究。实验结果表明，厌氧氨氧化反应对温度变化比较敏感，温度从31℃下降到17℃后，反应器内的厌氧氨氧化活性受到显著抑制，氨氮、亚硝酸盐氮和总氮的平均去除率迅速从97．0％、94．1％、86．0％下降为46．2％、41．8％、35．5％。当历时2个月反应器温度逐渐从17℃升高到31℃时，反应器内高效厌氧氨氧化活性逐渐得到恢复。反应器在17℃停止运行2个月后，直接升温至31℃再次运行，仅仅需要17d时间，反应器内厌氧氨氧化高活性就得到恢复，氨氮、亚硝酸盐氮和总氮的最高去除率达到99．4％、90．6％和85．0％。厌氧氨氧化反应的最佳温度应为31℃。     

Superior pillared clay catalysts for selective catalytic reduction of nitrogen oxides for power plant emission control

Fe(3+)-, Cr(3+)-, Cu(2+)-, Mn(2+)-, Co(2+)-, and Ni(2+)-exchanged Al2O3-pillared interlayer clay (PILC) or TiO2-PILC catalysts are investigated for the selective catalytic reduction (SCR) of nitric oxide by ammonia in the presence of excess oxygen. Fe(3+)-exchanged pillared clay is found to be the most active. The catalytic activity of Fe-TiO2-PILC could be further improved by the addition of a small amount of cerium ions or cerium oxide. H2O and SO2 increase both the activity and the product selectivity to N2. The maximum activity on the Ce-Fe-TiO2-PILC is more than 3 times as active as that on a vanadium catalyst. Moreover, compared to the V2O5-WO3/TiO2 catalyst, the Fe-TiO2-PILC catalysts show higher N2/N2O product selectivities and substantially lower activities (by approximately 85%) for SO2 oxidation to SO3 under the same reaction conditions. A 100-hr run in the presence of H2O and SO2 for the CeO2/Fe-TiO2-PILC catalyst showed no decrease in activity.     

Removal of ammonia solutions used in catalytic wet oxidation processes

Ammonia (NH(3)) is an important product used in the chemical industry, and is common place in industrial wastewater. Industrial wastewater containing ammonia is generally either toxic or has concentrations or temperatures such that direct biological treatment is unfeasible. This investigation used aqueous solutions containing more of ammonia for catalytic liquid-phase oxidation in a trickle-bed reactor (TBR) based on Cu/La/Ce composite catalysts, prepared by co-precipitation of Cu(NO(3))(2), La(NO(3))(2), and Ce(NO(3))(3) at 7:2:1 molar concentrations. The experimental results indicated that the ammonia conversion of the wet oxidation in the presence of the Cu/La/Ce composite catalysts was determined by the Cu/La/Ce catalyst. Minimal ammonia was removed from the solution by the wet oxidation in the absence of any catalyst, while approximately 91% ammonia removal was achieved by wet oxidation over the Cu/La/Ce catalyst at 230 degrees C with oxygen partial pressure of 2.0 MPa. Furthermore, the effluent streams were conducted at a liquid hourly space velocity of under 9 h(-1) in the wet catalytic processes, and a reaction pathway was found linking the oxidizing ammonia to nitric oxide, nitrogen and water. The solution contained by-products, including nitrates and nitrites. Nitrite selectivity was minimized and ammonia removal maximized when the feed ammonia solution had a pH of around 12.0.     

Photocatalytic oxidation of gaseous DMF using thin film TiO2 photocatalyst

The heterogeneous photocatalytic oxidation of gaseous N,N'-dimethylformamide (DMF) widely used in the manufacture of synthetic leather and synthetic textile was investigated. The experiments were carried out in a plug flow annular photoreactor coated with Degussa P-25 TiO2. The oxidation rate was dependent on DMF concentration, reaction temperature, water vapor, and oxygen content. Photocatalytic deactivation was observed in these reactions. The Levenspiel deactivation kinetic model was used to describe the decay of catalyst activity. Fourier transform infrared (FTIR) was used to characterize the surface and the deactivation mechanism of the photocatalyst. Results revealed that carbonylic acids, aldehydes, amines, carbonate and nitrate were adsorbed on the TiO2 surface during the photocatalytic reaction. The ions, NH4+ and NO3-, causing the deactivation of catalysts were detected on the TiO2 surface. Several treatment processes were applied to find a suitable procedure for the regeneration of catalytic activity. Among these procedures, the best one was found to be the H2O2/UV process.     

Phenol nitration upon oxidation of nitrite by Mn(III,IV) (hydr)oxides

An interesting aspect of the chemistry of nitrite is the possibility for this compound to interact with other environmental factors and many oxidising species, which results in the oxidation of nitrite to nitrogen dioxide. This is a potentially interesting process that can lead to the formation of nitroaromatic compounds in the environment. In previous papers we have shown that nitrite can interact with dissolved Fe(III) and nitrate under irradiation, Fenton and heterogeneous photo-Fenton reagents, and semiconductor oxides such as TiO2, alpha-Fe2O3, and beta-FeOOH under irradiation. This paper reports on the interaction between nitrite/nitrous acid and the Mn(III,IV) (hydr)oxides beta-MnO2 and gamma-MnOOH, both in neutral solution under irradiation and in acidic conditions in the dark. beta-MnO2 and gamma-MnOOH originate from the oxidation of Mn(II) and play a key role in the redox cycling of manganese in the environment. These Mn(III,IV) (hydr)oxides show some photocatalytic activity, and they can act as thermal oxidants at acidic pH. The photoinduced oxidation of nitrite and the thermal oxidation of nitrous acid by Mn(III,IV) (hydr)oxides yield nitrogen dioxide and lead to the formation of nitrophenols in the presence of phenol. These processes can take place at the water-sediment or water-colloid interface in natural waters and on the surface of atmospheric particulate. Furthermore, the phenol/gamma-MnOOH/HNO2 system in dark acidic solution is an interesting model due to the formation of phenoxyl radical upon phenol monoelectronic oxidation by gamma-MnOOH. The kinetics of nitrophenol generation under such conditions indicates that phenol nitration is unlikely to take place upon reaction between phenoxyl and *NO2 and suggests a solution to a literature debate on the subject.     

过渡金属氧化物催化氧化NO实验研究

采用沉淀法制备出一系列过渡金属氧化物催化剂,在内径为10 mm的固定床反应器中考察其对低浓度NO的催化氧化活性,催化反应活性顺序为:MnCrCoCuFeZn,并考察了以锰为活性组分采用低温固相法、流变相法和浸渍法制备的催化剂催化氧化NO的活性。实验结果表明,采用流变相法和低温固相法制备的锰氧化物催化剂,在反应温度150℃,NO浓度为5×10-4,O2为3%,N2为平衡气,空速51 000 h-1条件下,NO转化率分别为65%和57%;采用浸渍法制备的Mn/TiO2-10%催化剂,在反应温度200℃,空速相同的条件下,NO转化率为47%。     

Production of copper-based rare earth composite metal materials by coprecipitation and applications for gaseous ammonia removal

This study addresses the oxidation of ammonia (NH3) at temperatures between 423 and 673 K by selective catalytic oxidation (SCO) over a copper-based, rare earth composite metal material that was prepared by coprecipitating copper nitrate, lanthanum nitrate, and cerium nitrate at various molar ratios. The catalysts were characterized using Brunner, Emmett, and Teller spectroscopy, Fourier-transform infrared spectroscopy, Xray diffraction, ultraviolet-visible spectroscopy, cyclic voltammetric spectroscopy, and scanning electron microscopy. At a temperature of 673 K and an oxygen content of 4%, approximately 99.5% of the NH3 was reduced by catalytic oxidation over the 6:1:3 copper-lanthanum-cerium (molar ratio) catalyst. Nitrogen (N2) was the main product of this NH3-SCO process. Results from the activity and selectivity tests revealed that the optimal catalyst for catalytic performance had the highest possible cerium content and specific surface area (43 m2/g).     

Mn的氧化价态对Mn／γ-Al2O3催化剂催化臭氧氧化气相低浓度甲苯的影响

采用共沉淀法，以Al2O3为载体制备Mn／γ-Al2O3和Mn—Ce／Mn／γ-Al2O3催化剂，并分别在N2气氛和O2气氛下焙烧。采用固定床连续流动反应器，研究所制备催化剂在室温条件下催化臭氧氧化甲苯的性能。通过XRD、XPS和FTIR等手段对催化剂的结构和组成进行表征。结果表明，Mn／Mn／γ-Al2O3催化剂具有良好的催化臭氧氧化甲苯和催化臭氧自身分解的性能，共沉淀法制备催化剂的最佳Mn负载量为20％。O2气氛焙烧和Ce的加入，可以有效提高催化剂的活性和寿命。原因是O2气氛焙烧和Ce的加入可以提高Mn的氧化价态。催化剂失活的主要原因是有机副产物在催化剂表面吸附堆积，失活催化剂在550℃、空气气氛下焙烧可恢复催化性能。     

Effects of NO2 and SO2 on selective catalytic reduction of nitrogen oxides by ammonia

The selective catalytic reduction (SCR) characteristics of NO and NO(2) over V(2)O(5)-WO(3)-MnO(2)/TiO(2) catalyst using ammonia as a reducing agent have been determined in a fixed-bed reactor at 200-400 degrees C. The presence of NO(2) enhances the SCR activity at lower temperatures and the optimum ratio of NO(2)/NO(x) is found to be 0.5. During the SCR reactions, there are some side reactions occurred such as ammonia oxidation and N(2)O formation. At higher temperatures, the selective catalytic oxidation of ammonia and the nitrous oxide formation compete with the SCR reactions. The denitrification (DeNO(x)) conversion decreases at lower temperatures but it increases at higher temperatures with increasing SO(2) concentration. The presence of SO(2) in the feeds inhibits N(2)O formation.     

Fe2O3-Cr2O3/TiO2系列催化剂的结构和脱硝性能

研究以纳米TiO2为载体,浸渍负载过渡金属氧化物,以CO为还原剂的脱硝催化剂的脱硝性能。实验中以计算量的Ni（NO3）2和Fe（NO3）3混合溶液浸渍纳米TiO2粉末,室温下搅拌30 min至混合均匀,放入旋转蒸发器中,70℃下至水分蒸干为止;所得粉末在550℃下、空气气氛中焙烧4 h即得所需催化剂。用以上方法分别制备2%Fe2O3-10%Cr2O3/TiO2、4%Fe2O3-8%Cr2O3/TiO2、6%Fe2O3-6%Cr2O3/TiO2、8%Fe2O3-4%Cr2O3/TiO2与10%Fe2O3-2%Cr2O3/TiO2等5种催化剂样品。实验结果表明,制备的催化剂具有较好的结构,分散较为均匀。对于CO＋NO反应,Fe2O3-Cr2O3/TiO2系列催化剂具有较好的催化活性,NO的转化率都达到了100%。其中,10%Fe2O3-2%Cr2O3/TiO2样品具有最好的低温活性,H2-TPR结果表明,这是由于10%Fe2O3-2%Cr2O3/TiO2催化剂更易于被CO预还原。     

Cyclohexane oxidation and carbon deposition over metal oxide catalysts

Catalytic activity of V, Mn, Ni, Cu, Zn, Mo, Zr and Ce oxides over an -alumina support was evaluated for cyclohexane oxidation under oxygen deficient conditions in order to understand the relation between carbon deposition and catalytic activity/selectivity. Carbon formation over the catalysts during the oxidation reaction was measured by means of Fourier transformed infrared spectroscopy (FTIR). Catalysts Mn/Al₂O₃ and Ce/Al₂O₃, which are selective for deep oxidation of cyclohexane, possessed relatively carbon free surfaces. The catalysts with relatively high carbon deposition (V, Ni, Cu, Zn, Mo and Zr) produced CO in addition to CO₂. Traces of formaldehyde were produced over the catalysts Mo and V.