An Improved Model for Analyzing the Performance of Photocatalytic Oxidation Reactors in Removing Volatile Organic Compounds and Its Application

Abstract

An improved photocatalytic oxidation (PCO) reactor model was developed to analyze the removal of volatile organic compounds (VOCs) in indoor air. One new parameter, the average total removing factor K _t, together with the other two parameters, the number of mass transfer units NTU_m and the fractional conversion e, are found to be the main parameters influencing the photooxidation performance of PCO reactors. Three new parameters, the ideal reaction number of mass transfer units, NTU_m,ir; the ideal reaction fractional conversion, ε_ir; and the reaction effectiveness, η, also are defined. These concepts are helpful to the structural design and optimization for PCO reactors. The application of the model in designing a plate-type PCO reactor is demonstrated. This study shows that the present model is an effective tool for designing PCO reactors and for evaluating VOC removal performance of available PCO reactors.     

Nanofluid heat transfer under mixed convection flow in a tube for solar thermal energy applications

The solar flat plate collector operating under different convective modes has low efficiency for energy conversion. The energy absorbed by the working fluid in the collector system and its heat transfer characteristics vary with solar insolation and mass flow rate. The performance of the system is improved by reducing the losses from the collector. Various passive methods have been devised to aid energy absorption by the working fluid. Also, working fluids are modified using nanoparticles to improve the thermal properties of the fluid. In the present work, simulation and experimental studies are undertaken for pipe flow at constant heat flux boundary condition in the mixed convection mode. The working fluid at low Reynolds number in the mixed laminar flow range is undertaken with water in thermosyphon mode for different inclination angles of the tube. Local and average coefficients are determined experimentally and compared with theoretical values for water-based Al₂O₃ nanofluids. The results show an enhancement in heat transfer in the experimental range with Rayleigh number at higher inclinations of the collector tube for water and nanofluids.     

Some Factors that Affect the Deposition Rates of Sulfur Dioxide and Similar Gases on Vegetation

The deposition of sulfur dioxide on growing vegetation is affected by diverse environmental factors, many of which undergo large diurnal and spatial variations. The aerodynamic resistance to vertical transfer in the surface boundary layer can be formulated in terms of the friction velocity, height of observation, vertical heat flux, and surface roughness. Also important are the resistance in the air layer closest to the surface elements and, in dry vegetation, the average stomatal resistance of the plants. The latter variable is among the most difficult to estimate, but over many agricultural field crops like those in the midwestern U.S., a typical minimum value of average stomatal resistance to SO₂ transfer is about 0.7 s cm^-1, as is indicated by various experimental data. The deposition velocity can be estimated as the inverse of the sum of the resistances of the layers, necessarily down to where the concentrations are zero; in the surface boundary layer, any of the various resistances might be dominant. Above the surface layer, the micrometeorological relationships are known with less certainty, but reasonable approximations indicate that during unstable conditions the resistance to transfer is very small at heights of several tens of meters and during stable conditions the aerodynamic resistance is very large aloft.     

The Effects of Rotary Kiln Operating Conditions and Design on Burden Heating Rates as Determined by a Mathematical Model of Rotary Kiln Heat Transfer

A mathematical model of heat transfer in a directly-fired rotary kiln is developed and used to examine the effects of operating and design parameters on burden temperature. The model includes a mean beam length radiation model and axial zoning. Conductive and convective heat transfer are also included. Radiation between immediately adjacent zones is permitted. Calculation of heat transfer rates is facilitated by the use of an electric circuit analogue. An iterative solution procedure is adopted to solve the energy balance equations.

At the conditions examined, the model predicts that coflowlng gas and solid streams result in higher average burden temperatures than do counterflowing streams. The moisture level of the feed is predicted to be a key operating parameter. The effects of kiln length, burden residence time, firing rate, and flame length are also examined.     

Estimating PM10 air concentrations from dust storms in Iraq,Kuwait and Saudi Arabia

A model for the emission of PM₁₀ dust has been constructed using the concept of a threshold friction velocity which is dependent on surface roughness. Surface roughness in turn was correlated with geomorphology or soil properties for Kuwait, Iraq, part of Syria, Saudi Arabia, the United Arab Emirates and Oman. The PM₁₀ emission algorithm was incorporated into a Lagrangian transport and dispersion model. PM₁₀ air concentrations were computed from August 1990 through August 1991. The model predicted about the right number of dust events over Kuwait (events occur 18% of the time). The model results agreed quantitatively with measurements at four locations in Saudi Arabia and one in Kuwait for one major dust event (>1000 μg/m³). However, for smaller scale dust events (200–1000 μg/m³), especially at the coastal sampling locations, the model substantially over-predicted the air concentrations. Part of the over-prediction was attributed to the entrainment of dust-free air by the sea breeze, a flow feature not represented by the large-scale gridded meteorological data fields used in the model computation. Another part of the over-prediction was the model's strong sensitivity to threshold friction velocity and the surface soil texture coefficient (the soil emission factor), and the difficulty in accurately representing these parameters in the model. A comparison of the model predicted PM₁₀ spatial pattern with the TOMS satellite aerosol index (AI) yielded a spatial pattern covering a major portion of Saudi Arabia that was quite similar to the observed AI pattern.     

Energy transfer and kinetics in mechanochemistry

Mechanochemistry (MC) exerts extraordinary degradation and decomposition effects on many chlorinated, brominated, and even fluorinated persistent organic pollutants (POPs). However, its application is still limited by inadequate study of its reaction kinetic aspects. In the present work, the ball motion and energy transfer in planetary ball mill are investigated in some detail. Almost all milling parameters are summarised in a single factor—total effective impact energy. Furthermore, the MC kinetic between calcium oxide/Al and hexachlorobenzene is well established and modelled. The results indicate that total effective impact energy and reagent ratio are the two factors sufficient for describing the MC degradation degree of POPs. The reaction rate constant only depends on the chemical properties of reactants, so it could be used as an important index to appraise the quality of MC additives. This model successfully predicts the reaction rate for different operating conditions, indicating that it could be suitably applied for conducting MC reactions in other reactors.

     

Analysis of a solar still with photovoltaic modules and electrical heater - Energy and exergy approach

The availability of drinkable water, along with food and air, is a fundamental human necessity. Because of the presence of higher amounts of salt and pollution, direct use of water from sources such as lakes, sea, rivers, and subsurface water reservoirs is not normally suggested. Solar is still a basic technology that can use solar energy to transform accessible waste or brackish water into drinkable water. Exergy analysis is a strong inferential technique for evaluating the performance of thermal systems. Exergy is becoming more popular as a predictive tool for analysis, and there is a rising interest in using it. In this paper, performance analysis on the aspect of energy and exergy from the proposed solar still (PSS) (conventional solar still with the photovoltaic modules-AC heater) was analyzed on three different water depths (W_d) conditions (1, 2, and 3 cm). Using a solar still with an electric heater, the daily potable water production was found as 8.54, 6.37, and 4.43 kg, for the variations in water depth (W_d) of 1, 2, and 3 cm respectively. The energy and exergy efficiency of the PSS at the W_d of 1, 2, and 3 cm were 75.67, 51.45, and 37.21% and 5.08, 2.29, and 1.03%, respectively. At 1 cm W_d, PSS produced the maximum freshwater yield as compared to the other two water depths. When the W_d is increased from 1 to 2 cm and from 1 to 3 cm, the yield is decreased up to 27.3 and 52.7%, respectively. Similarly, the energy and exergy efficiency is decreased up to 36.8 and 53.2% and 50.4 and 80.6%, respectively. The water cost of the modified solar still is calculated as 0.028 $/kg for the least water thickness.

     

Energy and emission benefits of chicken manure biogas production: a case study

Studies on the production of biogas of different organic materials in an anaerobic environment are being carried out all over the world. The most important parameters in these researches can be listed as raw material potential, production processes, economic analyses, and environmental effects. Chicken manure is one of the raw materials used in biogas production. In this study, in addition to the analysis of biogas and energy production potential from chicken manure, greenhouse gas emissions were analyzed to evaluate environmental effects. In Turkey, chicken manure is not adequately processed and causes environmental pollution. The model biogas plant and potential energy generation were researched in this field study. The pilot plant produces 8.58 million m³ of biogas per year by processing about 110 thousand tons of waste. It produces 17 GWh/year of electricity and 16 GWh/year of thermal energy, as well as reducing CO₂ greenhouse gas emissions by 13.86 thousand tons/year.

     

Evaluating China’s regional energy and environmental efficiency by considering three internal parallel industries

With the rapid development of China’s economy, high energy consumption and high pollution emission have become serious problems. To solve these problems, many studies have been done to evaluate energy and environmental efficiency, as the results can provide valuable information to improve performance. However, the previous research mainly evaluates China’s regional energy and environmental efficiency by considering each region’s industry as a whole system, ignoring the internal structure. In reality, each region mainly includes three parallel types of industry: primary, secondary, and tertiary. Therefore, this paper provides a parallel data envelopment analysis (DEA) approach to evaluate China’s regional energy and environment efficiency by considering these parallel industrial systems. The following findings can be obtained based on the empirical results: (1) the overall energy efficiency of China is low, and the inefficiency of the economic system is mainly sourced from the lower energy and environmental performance of the primary industry and the tertiary industry. (2) the introduction of the environmental variable (CO₂) leads to the increase of some backward areas’ efficiencies. (3) the energy efficiency of each provincial region is different, and most of them have their own inefficient industries. (4) the total factor productivity of China is declining, mainly because of the decline of technical efficiency.

     

Estimates of carbon dioxide emissions based on incomplete condition information: a case study of liquefied natural gas in China

Recent calculations of carbon dioxide (CO₂) emissions have faced challenges because data consist of only partial information, which is called “incomplete information.” According to the emission factor method, energy consumption and CO₂ emission factors with incomplete information may lead to unmatched multiplication between themselves, which affects accuracy and increases uncertainties in emission results. To address a specific case of incomplete information that has not been fully explored, we studied the effects of incomplete condition information on the estimates of CO₂ emissions from liquefied natural gas (LNG) in China. Based on Chinese LNG sampling data, we obtained the specific-country CO₂ emission factor for LNG in China and calculated the corresponding CO₂ emissions. By applying hypothesis testing, regression analysis, variance analysis, or Monte Carlo (MC) simulations, the effects of incomplete information on the uncertainty of CO₂ emission calculations in three cases were analyzed. The results indicate that calorific values have more than a 9.8% impact on CO₂ emission factors and CO₂ emissions with incomplete sample information. Regarding incomplete statistical information, the impact of statistical temperature on CO₂ emissions exceeds 5.5%. Regarding incomplete sample and statistical information, sample and statistical temperatures can individually increase estimate biases by more than 5.2%. Significantly, the impacts of sample temperature and statistical temperature may offset each other. Therefore, the incomplete condition information is quite important and cannot be ignored in the estimation of CO₂ emissions from LNG and international fair comparison.

     

Effect of start of main injection timing on performance,emission, and combustion characteristics of a VGT CI engine fueled with neem biodiesel

The performance of engine parameters is more influenced with fuel injection strategies namely start of main injection timing (SoMI). An experimental analysis was performed to find the optimum SoMI timing based on performance, emission, and combustion characteristics. Base fuel of diesel and neem biodiesel was used as test fuels. The neem biodiesel was prepared by esterification and transesterification process. It is found from literature that neem biodiesel blend NB20 with diesel gives optimum performance and emission characteristics; therefore, NB20 blend was used for experiments. A variable geometry turbocharger (VGT) compression ignition (CI) engine was used to conduct the experiments. Engine performance parameters were estimated and compared with a base fuel of diesel and with NB20 blends. In this experimentation, fuel injection pressure (FIP) of 800 bar and engine speed of 1700 rpm were considered. SoMI timing was varied from 2° to 10° bTDC with an increment of 2° bTDC timing. Cylinder pressure (CP) and heat release rate (HRR) were estimated and found that are higher for diesel fuel compared to NB20 blend at different SoMI timings. The addition of neem biodiesel NB20 blend to diesel fuel decreases the exhaust emissions except NOx emissions. The BSFC was considerably reduced and BTE was improved almost equivalent to the diesel fuel for NB20. From the results, it is concluded that 10° bTDC SoMI timing provides 13% improvement in BTE, 21% decrement in BSFC, and 7.5% reduction in CO₂ emissions.

     

Application of different single extraction procedures for assessing the bioavailability of heavy metal(loid)s in soils from overlapped areas of farmland and coal resources

Heavy metal(loid) extraction from soils in overlapped areas of farmland and coal resources (OAFCR) is crucial in understanding heavy metal bioavailability in soil and the subsequent risks to crops and consumers. However, limited attention has been paid to the extraction procedure of heavy metal(loid)s in OAFCR soils in the research. This study therefore explored different single and mixed extraction procedures, such as acetic acid (HOAc), citric acid, ammonium bicarbonate-diethylenetriaminepentaacetic acid (AB-DTPA), ethylene diamine tetraacetic acid + ammonium acetate (EDTA+NH₄OAc), and total digestion (HNO₃-HClO₄-HF) to determine the bioavailability of As, Cd, Cr, Cu, Pb, and Zn in OAFCR soil in Xuzhou, China. The results showed the metal(loid) extraction capacity from soil of the different procedures could be ranked as AB-DTPA > EDTA+NH₄OAc > HOA_C > citric acid. The transfer ability of heavy metal(loid)s from soil to wheat tissues and from wheat roots to aerial parts was analyzed by calculating the bioconcentration factor and transfer factor, respectively. Transfer factors of all metal(loid)s were < 1 except Cr whose transfer factor from root to shell and straw were > 1. It is suspected that foliar uptake plays a dominant role in Cr uptake. Correlation analysis between the bioavailability of heavy metal(loid)s in soil and uptake in respective wheat tissues was performed to recommend the best extraction procedures for different studies. The results show that AB-DTPA extraction is recommended for Cu uptake to wheat roots, straws, shells and grains, Zn uptake to roots, and Cd uptake to roots and straws.

     

Interactive Analysis of Waste Recycling and Energy Recovery Program in a Small-Scale Incinerator

Abstract

Conflicting goals affecting solid waste management are explored in this paper to find the best implementation of resource recovery with a small-scale waste-to-energy process. Recycling paper and plastic material often leaves a shortage of thermal energy to support incineration that forces operators to supplement the process with auxiliary fuels. Although there are considerable profits to be made from material recovery, the increase of fuel usage causes conflict given that it is cost prohibitive. A series of trials performed on a small-scale 1.5-t/day incineration plant with a cyclone heat recovery system found that material recycling can impede performance. Experimental results are expressed as empirical regression formulas with regard to combustion temperature, energy transfer, and heat recovery. Process optimization is possible if the waste moisture content remains <30%. To test the robustness of the optimization analysis, a series of sensitivity analyses clarify the extent of material recycling needed with regard to plastic, paper, and metal. The experiments also test whether the moisture in the waste would decrease when recycling paper because of its exceptional capacity to absorb moisture. Results show that recycling paper is strongly recommended when the moisture content is >20%, whereas plastic recycling is not necessary at that moisture condition. Notably, plastic recovery reduces the heat needed to vaporize the water content of the solid waste, thus it is recommended only when the moisture content is <10%. For above-normal incineration temperatures, plastic recycling is encouraged, because it removes excess energy. Metal is confirmed as an overall priority in material recycling regardless of the moisture content of the incoming waste.     

Could China’s long-term low-carbon energy transformation achieve the double dividend effect for the economy and environment?

Exploring the low-carbon energy transformation pathway is vital to coordinate economic growth and environmental improvement for achieving China’s carbon peak target. Three energy-target scenarios are developed in this paper, considering the targets of energy structure, electrification rate, and carbon mitigation towards 2030 announced by the Chinese government. A dynamic multi-sectoral computable general equilibrium model, CHINAGEM, is employed to examine the economic and environmental effects under different pathways of long-term low-carbon transformation. It detects that China’s energy structure would substantially transfer to the low-carbon and clean one, whereas CO₂, SO₂, and NO_X emissions in 2020–2030 would vastly abate along with all three energy-target scenarios. Different pathways would produce varying positive impacts on China’s macro-economy and achieve the different extent of double dividend effects. It is highly conceivable for China to peak its carbon emission at 12.4 GtCO₂ by 2028 if it serves the comparatively more stringent low-carbon transformation pathways.

     

Fluoride removal from aqueous solution by direct contact membrane distillation: theoretical and experimental studies

Direct contact membrane distillation (DCMD) process using polyvinylidene fluoride (PVDF) membrane was used for fluoride removal from aqueous solution. This study has been carried out on heat and mass transfer analyses in DCMD. The dusty-gas model was used to analyze the mass transfer mechanism and to calculate the permeate flux. The heat transfer is analyzed based on energy balance, and the different layers are considered as a series of thermal resistances. Mass transfer analysis showed that the transition Knudsen-molecular diffusion is the dominant mechanism to describe the transport of water vapor through the pores of the PVDF membrane. The most significant operating parameter is the feed temperature. The permeate increases sensitively with feed temperature and velocity, and it shows insignificant change with feed salts concentration. Heat transfer analysis showed the conduction through the matrix of the membrane presents the major part of available energy. The increasing feed temperature leads to increase thermal efficiency (TE) and decrease temperature polarization coefficient (TPC). The experimental results are in good agreement with theoretical values. Therefore, it is suggested to work at high feed temperature, which will benefit both the thermal efficiency and permeate flux. The experimental results proved that DCMD process is able to produce almost fluoride-free water suitable for many beneficial uses.     

The Sensitivity of PM25 Source-Receptor Relationships to Atmospheric Chemistry and Transport in a Three-Dimensional Air Quality Model

ABSTRACT

Air quality model simulations constitute an effective approach to developing source-receptor relationships (so-called transfer coefficients in the risk analysis framework) because a significant fraction of particulate matter (particularly PM_2.5) is secondary (i.e., formed in the atmosphere) and, therefore, depends on the atmospheric chemistry of the airshed. In this study, we have used a comprehensive three-dimensional air quality model for PM_{2 5} (SAQM-AERO) to compare three approaches to generating episodic transfer coefficients for several source regions in the Los Angeles Basin. First, transfer coefficients were developed by conducting PM_2.5 SAQM-AERO simulations with reduced emissions of one of four precursors (i.e., primary PM, sulfur dioxide (SO₂), oxides of nitrogen (NO_x), and volatile organic compounds) from each source region. Next, we calculated transfer coefficients using two other methods: (1) a simplified chemistry for PM_2.5 formation, and (2) simplifying assumptions on transport using information limited to basin-wide emission reductions. Transfer coefficients obtained with the simplified chemistry were similar to those obtained with the comprehensive model for VOC emission changes but differed for NO and SO emission changes. The differences were due to the parameterization of the rates of secondary PM formation in the simplified chemistry. In 90% of the cases, transfer coefficients estimated using only basin-wide information were within a factor of two of those obtained with the explicit source-receptor simulations conducted with the comprehensive model. The best agreement was obtained for VOC emission changes; poor agreement was obtained for primary PM_2.5.     

Renewable energy powered membrane desalination — review of recent development

Due to current water stress, there is a problem with hygiene and sanitation in many parts of the world. According to predictions from the United Nations, more than 2.7 billion people will be challenged by water scarcity by the middle of the century. The water industry is increasingly interested in desalination of the sea, ocean, and brackish water. Desalination processes are widely classified as thermal or membrane technologies. In the Middle East, thermal desalination remains the primary technology of choice, but membrane processes, for example reverse osmosis (RO), have evolved rapidly and in many other parts of the world are currently even surpassing thermal processes. The purpose of this paper is to review the renewable energy source, the technology, desalination systems, and their possible integration with renewable energy resources and their cost. This article suggests that the most practical renewable desalination techniques to be used are the solar photovoltaic integrated RO desalination process, the hybrid solar photovoltaic-wind integrated RO desalination process, the hybrid solar photovoltaic-thermal (PVT) integrated RO desalination process, and the hybrid solar photovoltaic-thermal effect distillation (PVT-MED) desalination process. However, intensive research is still required to minimize the cost, reduce the heat loss, enhance the performance, and increase the productivity.

     

Chemical transport models

Background, aim, and scope  Improving the parameterization of processes in the atmospheric boundary layer (ABL) and surface layer, in air quality and chemical transport models. To do so, an asymmetrical, convective, non-local scheme, with varying upward mixing rates is combined with the non-local, turbulent, kinetic energy scheme for vertical diffusion (COM). For designing it, a function depending on the dimensionless height to the power four in the ABL is suggested, which is empirically derived. Also, we suggested a new method for calculating the in-canopy resistance for dry deposition over a vegetated surface. Materials and methods  The upward mixing rate forming the surface layer is parameterized using the sensible heat flux and the friction and convective velocities. Upward mixing rates varying with height are scaled with an amount of turbulent kinetic energy in layer, while the downward mixing rates are derived from mass conservation. The vertical eddy diffusivity is parameterized using the mean turbulent velocity scale that is obtained by the vertical integration within the ABL. In-canopy resistance is calculated by integration of inverse turbulent transfer coefficient inside the canopy from the effective ground roughness length to the canopy source height and, further, from its the canopy height. Results  This combination of schemes provides a less rapid mass transport out of surface layer into other layers, during convective and non-convective periods, than other local and non-local schemes parameterizing mixing processes in the ABL. The suggested method for calculating the in-canopy resistance for calculating the dry deposition over a vegetated surface differs remarkably from the commonly used one, particularly over forest vegetation. Discussion  In this paper, we studied the performance of a non-local, turbulent, kinetic energy scheme for vertical diffusion combined with a non-local, convective mixing scheme with varying upward mixing in the atmospheric boundary layer (COM) and its impact on the concentration of pollutants calculated with chemical and air-quality models. In addition, this scheme was also compared with a commonly used, local, eddy-diffusivity scheme. Simulated concentrations of NO₂ by the COM scheme and new parameterization of the in-canopy resistance are closer to the observations when compared to those obtained from using the local eddy-diffusivity scheme. Conclusions  Concentrations calculated with the COM scheme and new parameterization of in-canopy resistance, are in general higher and closer to the observations than those obtained by the local, eddy-diffusivity scheme (on the order of 15–22%). Recommendations and perspectives  To examine the performance of the scheme, simulated and measured concentrations of a pollutant (NO₂) were compared for the years 1999 and 2002. The comparison was made for the entire domain used in simulations performed by the chemical European Monitoring and Evaluation Program Unified model (version UNI-ACID, rv2.0) where schemes were incorporated.     

无机材料对固定化微生物凝胶球性能的影响

为了提高固定化微生物凝胶球的性能,实验研究了在凝胶球中添加无机材料粉末活性炭、SiO2、CaCO3和人造沸石,并从固定化微生物凝胶球的生物活性、机械强度、微观结构和溶出性多方面考核,比较不同无机材料对凝胶球性能的影响。研究结果表明,添加CaCO3能明显提高凝胶球的传质性能,进而提高凝胶球对氨氮的处理效果,添加人造沸石能提高凝胶球的抗拉强度,添加SiO2能提高凝胶球的密度,添加粉末活性炭能提高凝胶球的压缩强度。     

The Autothermal Pyrolysis of Waste Tires

Abstract

The growing amount of rubber waste, such as that from tires and cables, has resulted in serious environmental problems. Since rubber waste is not easily biodegradable even after a long period of landfill treatment, material and energy recovery is the preferable alternative to disposal. The potential offered by waste tire pyrolysis for solving both energy and waste treatment problems is widely recognized. Pyrolysis is one method of inducing thermal decomposition without using any oxidizing agent, or using such a limited supply of the agent that oxidization does not proceed to an appreciable extent. The latter may be described as autothermal pyrolysis and will be studied in the present work.

The main objective of this research was to study the operating parameters of autothermal pyrolysis of scrap tires in a laboratory-scale fluidized bed reactor with a 100-cm bed height (10 cm I.D.) and a 100-cm freeboard (25 cm I.D.). Scrap tires were pyrolyzed in a limited oxygen supply, so that the heat for pyrolysis of the scrap tires was provided by combustion of some portion of the scrap tires. The operating parameters evaluated included the effect on the pyrolysis oil products and their relative proportions of (1) the air factor (O.O7–O35); (2) the pyrolysis temperature (370–570 °C); and (3) the catalyst added (zeolite and calcium carbonate). The results show that: (1) the composition of the liquid hydrocarbon obtained is affected significantly by the air factor; (2) the higher operating temperature caused a higher yield of gasoline and diesel; (3) the yield of gasoline increased due to the catalyst zeolite added, and the yield of diesel increased due to the addition of the catalyst calcium carbonate; (4) the principal constituents of gasoline included dipentene and diprene.