Heterogeneous photocatalysis of aromatic and chlorinated volatile organic compounds (VOCs) for non-occupational indoor air application

The current study evaluated the technical feasibility of applying TiO2 photocatalysis to the removal of low-ppb concentrations of volatile organic compounds (VOCs) commonly associated with non-occupational indoor air quality issues. A series of experiments was conducted to evaluate five parameters (relative humidity (RH), hydraulic diameter (HD), feeding type (FT) for VOCs, photocatalytic oxidation (PCO) reactor material (RM), and inlet port size (IPS) of PCO reactor) in relation to the PCO destruction efficiencies of the selected target VOCs. None of the target VOCs exhibited any significant dependence on the RH, which is inconsistent with a previous study where, under conditions of low humidity and a ppm toluene inlet level, a drop in the PCO efficiency was reported with a decreasing humidity. However, the other four parameters (HD, RM, FT, and IPS) were found to be important for better VOC removal efficiencies as regards the application of TiO2 photocatalytic technology for cleansing non-occupational indoor air. The PCO destruction of VOCs at concentrations associated with non-occupational indoor air quality issues was up to nearly 100%, and the CO generated during PCO was a negligible addition to indoor CO levels. Accordingly, a PCO reactor would appear to be an important tool in the effort to improve non-occupational indoor air quality.     

Ba/TiO_2/MCM-41光催化降解对硝基苯甲酸

以钛酸丁酯为钛源、MCM-41分子筛为载体,采用溶胶-凝胶法制备了掺杂与负载相结合的光催化剂Ba/TiO2/MCM-41。结果表明：Ba/TiO2/MCM-41是一种比表面积高达341.2 m2/g的介孔材料,主要晶相为锐钛矿相,比P25有更强的紫外光吸收。将Ba/TiO2/MCM-41用于光催化氧化水中的对硝基苯甲酸,当催化剂投加量为0.5 g/L,对硝基苯甲酸初始pH为4、浓度为2×10-4mol/L时,紫外光照30 min后,对硝基苯甲酸降解率达到96.0%。用紫外光谱、红外光谱和高效液相色谱分析对硝基苯甲酸降解前后的变化,发现随着光照时间延长,苯环上的硝基、羧基吸收峰逐渐减弱;对硝基苯甲酸首先被降解为一些中间小分子产物,随着反应进行,小分子物质也逐渐被降解。     

臭氧与TiO2/UV协同降解对氯苯酚

利用O3／UV、TiO2／UV和O3／TiO2／UV降解对氯苯酚表明，臭氧与TiO2／UV具有明显的协同作用，如在本实验条件下降解5min后，上述3者对对氯苯酚的去除率分别为55％、10％和77%。O3／TiO2／UV协同作用的本质是由于臭氧能带走二氧化钛光致电子空穴对中的电子，从而产生了更多的羟基自由基，加速了有机物的降解。     

Ba/TiO2/MCM-41光催化降解对硝基苯甲酸

以钛酸丁酯为钛源、MCM-41分子筛为载体,采用溶胶-凝胶法制备了掺杂与负载相结合的光催化剂Ba/TiO2/MCM-41。结果表明:Ba/TiO2/MCM-41是一种比表面积高达341.2 m2/g的介孔材料,主要晶相为锐钛矿相,比P25有更强的紫外光吸收。将Ba/TiO2/MCM-41用于光催化氧化水中的对硝基苯甲酸,当催化剂投加量为0.5 g/L,对硝基苯甲酸初始pH为4、浓度为2×10-4mol/L时,紫外光照30 min后,对硝基苯甲酸降解率达到96.0%。用紫外光谱、红外光谱和高效液相色谱分析对硝基苯甲酸降解前后的变化,发现随着光照时间延长,苯环上的硝基、羧基吸收峰逐渐减弱;对硝基苯甲酸首先被降解为一些中间小分子产物,随着反应进行,小分子物质也逐渐被降解。     

Removal of indoor pollutants under UV irradiation by a composite TiO2-zeolite sheet prepared using a papermaking technique

Toluene and formaldehyde are malodorous and cause indoor pollution. These materials have received much attention as hazardous and malodorous substances. It is well known that long-term exposure to even fairly low levels of toluene and formaldehyde brings about the risk of asthma and eczema. In this study, a composite TiO2-zeolite (ZE) sheet prepared using a papermaking technique was applied to remove toluene and formaldehyde under UV irradiation. The optimum composition of the TiO2 (Ti)-ZE sheet was studied in detail with regard to the effective removal of various indoor pollutants. Gaseous toluene and formaldehyde were removed by a composite TiO2-ZE sheet with different efficiencies depending upon the ratio of Ti/ZE in the composite sheet. The composite sheets could decompose formaldehyde and toluene repeatedly after being recharged. It was shown that the sheets are potentially applicable as highly functional materials to be placed on walls and ceilings of houses for the removal of various indoor pollutants.     

Simultaneous decontamination of hexavalent chromium and methyl tert-butyl ether by UV/TiO2 process

Hexavalent chromium and methyl tert-butyl ether (MTBE) are two important environmental pollutants. Simultaneous decontamination of Cr(VI) and MTBE was studied by UV/TiO2 process. The influences of pH and the concentrations of pollutants on the kinetics of the photocatalytic reactions were evaluated. Dark adsorption tests showed that the acidic pH favored the adsorption of Cr(VI) while neutral pH favored the adsorption of MTBE. Under UV irradiation, Cr(VI) reduction was observed in Cr(VI)/TiO2 system, and MTBE oxidation was observed in MTBE/TiO2 system. The system containing Cr(VI) and MTBE by UV/TiO2 process demonstrated the synergistic effect between oxidation of MTBE and reduction of Cr(VI). The results demonstrated that two pollutants Cr(VI) and MTBE could be eliminated simultaneously by UV/TiO2 process. tert-Butyl formate, tert-butyl alcohol and acetone were identified as primary degradation products of MTBE by gas chromatography-mass spectrometry in the degradation of MTBE by UV/TiO2 process.     

Kinetics and mechanism of TNT degradation in TiO2 photocatalysis

The photocatalytic degradation of TNT in a circular photocatalytic reactor, using a UV lamp as a light source and TiO(2) as a photocatalyst, was investigated. The effects of various parameters such as the initial TNT concentration, and the initial pH on the TNT degradation rate of TiO(2) photocatalysis were examined. In the presence of both UV light illumination and TiO(2) catalyst, TNT was more effectively degraded than with either UV or TiO(2) alone. The reaction rate was found to obey pseudo first-order kinetics represented by the Langmuir-Hinshelwood model. In the mineralization study, TNT (30 mg/l) photocatalytic degradation resulted in an approximately 80% TOC decrease after 150 min, and 10% of acetate and 57% of formate were produced as the organic intermediates, and were further degraded. NO(-)(3) NO(-)(2), and NH(+)(4) were detected as the nitrogen byproducts from photocatalysis and photolysis, and more than 50% of the total nitrogen was converted mainly to NO(-)(3)in the photocatalysis. However, NO(-)(3) did not adsorbed on the TiO(2) surface. TNT showed higher photocatalytic degradation efficiency at neutral and basic pH.     

Study on particulates and volatile organic compounds removal with TiO2 nonwoven filter prepared by electrospinning

In this study, polyvinyl alcohol (PVA) and titania (TiO₂) Degussa P-25 were mixed to generate TiO₂ nonwoven filters using electrospinning. The wires of titanium dioxide and the nonwoven binding titania nanofibers were formed using 14 kV voltage and a distance of 15 cm. A single-factor experimental method was used to investigate the effects of parameters such as initial concentration, retention time, and light source on acetone removal by nonwoven binding titania nanofibers. Furthermore, the effects of parameters such as gas pressure, particle size, initial concentration, and retention time on the removal of particulates were also assessed. The results showed that the degradation efficiency increased with decreasing initial concentrations and increasing retention time. The best operational conditions during this study for the removal of acetone using the TiO₂ nonwoven filters were a retention time of 100 sec, initial acetone concentration of 250 ppm, and ultraviolet (UV) light source of 254 nm. Under those conditions, 99% acetone removal efficiency was obtained. In addition, 90% particulate matter removal efficiency was reached when the particulate size was greater than 200 nm and the reaction time was longer than 5 minutes. The prepared TiO₂/nanofiber has good performance for volatile organic compounds (VOCs) and particulate removal at the same time.

Implications: In this study, polyvinyl alcohol (PVA) and titania (TiO₂) Degussa P-25 were mixed to generate TiO₂ nonwoven filters using electrospinning. The results showed that the optimum operating conditions for the removal of acetone using the TiO₂ nonwoven filters were a retention time of 100 sec, initial acetone concentration of 250 ppm, and UV light source of 254 nm. Under those conditions, 99% acetone removal efficiency was obtained.     

CNTs/TiO2/CS光降解苯的动力学

综合光催化氧化苯的动力学过程、光辐射场模型和质量守恒定律,采用平板型反应器建立了碳纳米管/二氧化钛/壳聚糖（CNTs/TiO2/CS）催化薄膜光催化氧化气相苯的数学模型;该模型考虑了光强、相对湿度、初始浓度与气体流速对气相苯光降解的影响。结果表明,建立的数学模型与实验结果吻合较好。     

Photocatalytic degradation of isoproturon herbicide over TiO2/Al-MCM-41 composite systems using solar light

The present investigation covers immobilization of TiO2 using a simple solid state dispersion technique over mesoporous Al-MCM-41 support for the treatment of isoproturon herbicide. Catalysts are characterized by XRD, X-ray photo electron spectroscopy (XPS), surface area, UV-Vis diffused reflectance spectra (DRS), SEM and TEM. A detailed photocatalytic degradation study of isoproturon under solar light in aqueous suspensions is reported. The 10 wt% TiO2/Al-MCM-41 composite system found to be optimum with high degradation activity. The reaction follows pseudo-first order kinetics. The parameters like TiO2 loading over Al-MCM-41, amount of catalyst, concentration of substrate, pH effect, durability of the catalyst, activity comparison of TiO2 and Al-MCM-41 supported system are studied. The mineralization of isoproturon is monitored by TOC. Based on the degradation products detected through LC-MS, a plausible degradation mechanism is proposed. The data indicates that TiO2/Al-MCM-41 composite system is an effective photocatalyst for treatment of isoproturon in contaminated water.     

Decomposition of gas-phase trichloroethene by the UV/TiO2 process in the presence of ozone.

The decomposition of gas-phase trichloroethene (TCE) in air streams by direct photolysis, the UV/TiO2 and UV/O3 processes was studied. The experiments were carried out under various UV light intensities and wavelengths, ozone dosages, and initial concentrations of TCE to investigate and compare the removal efficiency of the pollutant. For UV/TiO2 process, the individual contribution to the decomposition of TCE by direct photolysis and hydroxyl radicals destruction was differentiated to discuss the quantum efficiency with 254 and 365 nm UV lamps. The removal of gaseous TCE was found to reduce by UV/TiO2 process in the presence of ozone possibly because of the ozone molecules could scavenge hydroxyl radicals produced from the excitation of TiO2 by UV radiation to inhibit the decomposition of TCE. A photoreactor design equation for the decomposition of gaseous TCE by the UV/TiO2 process in air streams was developed by combining the continuity equation of the pollutant and the surface catalysis reaction rate expression. By the proposed design scheme, the temporal distribution of TCE at various operation conditions by the UV/TiO2 process can be well modeled.     

Photocatalytic oxidation of volatile organic compounds using fluorescent visible light

Photocatalytic oxidation (PCO) of volatile organic compounds (VOCs) is a highly attractive alternative technology for purification and deodorization of indoor air. The main objectives of this study were to demonstrate that a common fluorescent visible light (FVL) lamp can be used to effectively remove by PCO low concentrations of VOCs from slightly contaminated air and to provide some fundamental and technical details on the process. The target VOC was n-butanol, which is a standard reference odorant. Its PCO was studied under a long residence time in a 3.7-L cylindrical reactor with commercial titanium dioxide (TiO2) as the reference photocatalyst and using mostly FVL for illumination. For comparison only, a UV (black) light lamp was used. The gas-phase products were detected and quantified online by gas chromatography (GC). The effects of reactor residence time, of inlet concentration, and of the relative light intensity on the efficiency of the process were also evaluated. At a high n-butanol concentration (0.1 vol %), butanal and propanal were identified as the intermediate products of the process; ethanal appeared when the initial concentration was < or = 850 ppm(v). This indicates that PCO leading to CO2 and H2O is relatively slow and proceeds in a stepwise manner. Although the efficiency of the process with an FVL lamp was significantly lower than when using a UV black light, complete PCO of low concentrations was achieved for 100 ppm(v). In a search for a material with photoactivation extended to higher wavelengths or increased photoactivity, several samples of transition metal- or silver ion-doped (2 atomic %) TiO2 as well as SrTi(1-x-)Fe(x)O3 (x = 0.1 and 0.15) perovskites were included in the study. None of these materials was more active than pure TiO2. The results of this study open new horizons in the area of in door air quality (IAQ) control.     

Photocatalytic degradation of lignin using Pt/TiO2 as the catalyst

Photocatalytic degradation of lignin was studied with the use of catalysts TiO(2) and Pt/TiO(2). The influence of several experimental parameters, i.e. pH, catalyst dosage and illumination on lignin degradation was investigated. The results showed that application of UV irradiation alone has almost no effect on the reduction of dissolved organic carbon (DOC) and American Dye Manufacture Institute value (ADMI). However, the addition of TiO(2) and Pt/TiO(2) reduced the original DOC (251 mg l(-1)) by more than 40% within 30 min of treatment and the reaction can be simulated with pseudo-first order kinetics. Rapid degradation of lignin was observed in acidic solution using either TiO(2) or Pt/TiO(2) as the catalyst compared to high pH cases. The content of Pt in the Pt/TiO(2) catalyst is 1%. In addition, too much catalyst addition has not increased the DOC and ADMI reduction proportionally. The investigation also indicated that the photocatalytic degradation rates could be enhanced 1-6 times faster after doping TiO(2) with Pt in different pH cases. A modified Nernst type model was adopted to simulate the decoloring process using TiO(2) and Pt/TiO(2) based on the profiles of oxidation reduction potential during the photocatalytic reaction. The developed equation can be used to predict the color removal efficiency of lignin wastewater by the photocatalytic process.     

Adsorption of mesitylene via mesoporous adsorbents

Mesitylene (or 1,3,5-trimethylbenzene) is a volatile organic compound emitted from various industrial processes, e.g., spray coating. Its emissions have become a critical issue because mesitylene is toxic and cannot be removed using traditional adsorbents, e.g., zeolite (H-ZSM-5; the diameter of mesitylene molecules is greater than the pore size of H-ZSM-5). Hence, an adsorbent with a large pore size, MCM-41, is used in this study to investigate its adsorption capacity for mesitylene and compare with that of H-ZSM-5. Experimental results reveal that MCM-41 without Al₂O₃ exhibits a good adsorption capacity (184 mg/g) for the gas stream containing 100 ppm of mesitylene at a relative humidity of 10%. The adsorption kinetics is well described by the Freundlich isotherm. Furthermore, experimental results reveal that MCM-41 is effective for the adsorption of low concentrations (10 ppm) of mesitylene. In addition, adsorption–desorption tests revealed that the sample MCM-41-AS is stable to sustain the adsorption capacity after 10 adsorption–desorption cycles. After 10 adsorption–desorption cycles, MCM-41-AS retains 92.4% of its initial adsorption capacity (170 vs. 184 mg/g). Finally, MCM-41 and H-ZSM-5 in series are effective for the simultaneous removal of mesitylene and toluene in the gas stream.

Implications: This study aims to improve the performance of adsorbent for mesitylene, which is typically applied in the spray-coating industry. The zeolite MCM-41-AS is selected as a candidate for the investigation. Experimental results reveal that MCM-41-AS exhibits a good adsorption capacity for mesitylene and that it can be integrated with H-ZSM-5-25 for the simultaneous adsorption of mesitylene and toluene.     

Decolorizing of lignin wastewater using the photochemical UV/TiO2 process

Studies on applying the photochemical UV/TiO2 oxidation process to treat the lignin-containing wastewater for dissolved organic carbon (DOC), color and reducing A254 (the absorption at the wavelength of 254 nm) have been carried out. The data obtained in this study demonstrate that the UV/TiO2 process is effective in oxidizing the lignin thus reducing the color and DOC of the wastewater treated. The combined UV/TiO2 treatment can achieve better removal of DOC and color than the UV treatment alone. Color removal, based on American Dye Manufacture Index (ADMI) measurement, is greater than 99% if the pH is maintained at 3.0 with the addition of 1 g l(-1) TiO2. When 10 g l(-1) TiO2 is applied, the oxidation reduction potential (ORP) value is reached to result in an 88% removal of both DOC and color. A model was developed based on the variation of ORP during the photochemical reaction to simulate the decoloring process. The proposed model can be used to predict the color removal efficiency of the UV/TiO2 process.     

活性炭纤维负载TiO2光催化降解甲醛的影响因素

利用自制光催化气体反应器体系,以活性炭纤维负载TiO2作催化剂,在紫外光照射下模拟降解室内污染气体甲醛,测试了活性炭纤维负载TiO2催化剂的催化活性,探讨了紫外光光强、催化剂的酸度、反应器内湿度及反应时间等控制反应的主要因素对甲醛降解率的影响。结果表明,活性炭纤维与TiO2的协同作用大大提高了对甲醛的降解效果;紫外光强增倍对甲醛降解率有一定提高,但提高幅度仅为11.71%;活性炭纤维用pH=5的TiO2溶胶浸泡做催化剂对甲醛的降解效果最好,60 min内降解率达到68.37%;反应器内的湿度为81%甲醛降解率最高,反应60 min后达82.2%;随着反应时间的延长,甲醛降解率的上升幅度不断减小,最高只能达到94.59%。     

Photochemical and photocatalytic degradation of gaseous toluene using short-wavelength UV irradiation with TiO2 catalyst: comparison of three UV sources

The feasibility of the use of short-wavelength UV (254+185 nm) irradiation and TiO2 catalyst for photodegradation of gaseous toluene was evaluated. It was clear that the use of TiO2 under 254+185 nm light irradiation significantly enhanced the photodegradation of toluene relative to UV alone, owed to the combined effect of photochemical oxidation in the gas phase and photocatalytic oxidation on TiO2. The photodegradation with 254+185 nm light irradiation was compared with other UV wavelengths (365 nm (black light blue lamp) and 254 nm (germicidal UV lamp)). The highest conversion and mineralization were obtained with the 254+185 nm light. Moreover, high conversions were achieved even at high initial concentrations of toluene. Catalyst deactivation was also prevented with the 254+185 nm light. Regeneration experiments with the deactivated catalyst under different conditions revealed that reactive oxygen species played an important role in preventing catalyst deactivation by decomposing effectively the less reactive carbon deposits on the TiO2 catalyst. Simultaneous elimination of photogenerated excess ozone and residual organic compounds was accomplished by using a MnO2 ozone-decomposition catalyst to form reactive species for destruction of the organic compounds.     

外负载Ce-TiO_2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭（AC）为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明：外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

Photodegradation of alachlor with the TiO(2) film immobilised on the glass tube in aqueous solution

Alachlor photodegradation was performed using TiO(2), which was synthesized by a modified sol-gel method. The thickness of a TiO(2) film immobilised by a 5-time dip-coating was 174 nm and the average diameter of TiO(2) particles was about 10-15 nm in SEM images. The crystal structure of a TiO(2) film calcinated at 300 degrees C for 1 h was observed as a typical anatase type. The stability of a TiO(2) film by a modified sol-gel method was 4% better than TiO(2) by a typical sol-gel method.The removal rate of alachlor with both Fe(3+) and UV radiation in the absence of TiO(2) was 0.28 mg/l/h in 10 h and the removal rate of alachlor with Fe(3+)/UV in the presence of TiO(2) was 0.32 g/l/h, which was higher by 14% than that with Fe(3+)/UV system. TOC concentration during the alachlor degradation with both TiO(2) and UV radiation in the absence of added Fe(3+) decreased from 100%, through 81% and 51%, to 44% with time elapses of 4, 8, and 10 h, respectively, while TOC concentration with both added Fe(3+) and UV radiation in the absence of TiO(2) decreased from 100% to 70% in 10 h.     

Degradation of short-chain alkyl- and alkanolamines by TiO2- and Pt/TiO2-assisted photocatalysis

The photooxidation of C2H5NH2, (C2H5)2NH, HOC2H4NH2, (HOC2H4)2NH and (HOC2H4)3N using TiO2 and Pt/TiO2 as photocatalysts has been investigated. A laboratory set up was designed and a study on the influence of the concentration of the photocatalyst, the pH-value and the structure of the amine performed. The photocatalytic process was optimized with respect to the concentrations of the model substances during degradation. The decrease of the amine concentrations was found to be maximum at a pH of 10. The time-dependence of the formation of cationic breakdown products, such as NH3/NH4 and short-chain alkyl- and alkanolamines was studied by analyses with single column ion chromatography. The experimental data show that the photodegradation follows a Langmuir-Hinshelwood kinetic. The mineralization of the model substances also was monitored by measurements of the decrease of the TOC and of the formation of NO2 and NO3. The different mineralization efficiencies for the model substances studied are discussed with regard to their structure and adsorption behaviour on the photocatalyst. A possible breakdown mechanism involving the electrophilic attack of the hydroxyl radical is given. The applicability of the TiO2-assisted photocatalytic degradation of C2H5NH2 and (C2H5)2NH was tested at the pilot plant-scale with real solar radiation. The degradation rates and products obtained were similar to those found in the laboratory experiments.