SBR-混凝处理渗滤液过程中有机物的变化特征

考察了SBR-混凝组合工艺对垃圾渗滤液中溶解性有机物(DOM)不同分子量区间物质及组分腐殖酸(HA)、富里酸(FA)和亲水性有机物(Hy I)的去除效果,同时利用傅里叶红外光谱及三维荧光光谱对处理过程中DOM各组分变化特性进行了分析。结果表明,组合工艺对表观分子量为2 000~4 000及2 000的DOM去除率分别为89.3%和72.1%;对渗滤液DOM组分HA、FA和Hy I的去除率分别为-52.0%、73.1%和77.1%。红外光谱显示,DOM各组分都含有醇、羧酸、脂等多种有机物,SBR对糖、醇、羧酸等去除效果较好,而混凝对脂肪族及芳香族化合物去除效果较好;三维荧光光谱分析表明,经组合工艺处理,DOM各组分荧光峰强度及复杂化程度明显降低,且SBR工艺对色氨酸等类蛋白物质去除效果较好,混凝工艺对类腐殖酸、类富里酸等大分子物质的去除效果较好。     

垃圾渗滤液处理工艺中有机污染物的三维荧光光谱

利用荧光发射和三维荧光光谱研究了三峡库区某垃圾堆场的渗滤液及其处理工艺出水溶解性有机质(DOM)的荧光光谱特性。堆场渗滤液的DOM含有类酪氨酸、色氨酸及紫外区类富里酸，特征荧光峰中心位于E_x/E_m=275 nm/305 nm，为高激发波长类酪氨酸，与前人的研究结果并不一致，这可能与垃圾的堆放期有关。渗滤液和各处理工艺出水的荧光指数f_450/500均大于1.9，表明腐殖质主要为微生物源。渗滤液在处理前后荧光峰特征和强度均发生明显改变，类蛋白荧光强度与DOC值变化趋势基本一致。生化处理工艺中，类蛋白荧光强度降低了66.4%～95.5%，紫外区类富里酸荧光强度只降低了28.8%，显示类蛋白质具有良好的可生化性，而类富里酸相对较难生化降解。三维荧光光谱能反映渗滤液处理过程中污染物的种类、性质和数量等变化信息，能快速地进行定性分析、定量评价。     

回灌型准好氧填埋场脱氮特性及加速稳定化研究

采用2个模拟填埋生物反应器,1号柱渗滤液简单回灌,2号柱为渗滤液回灌准好氧联合运行方式,研究了渗滤液回灌准好氧生物反应器填埋场的脱氮特性及加速垃圾稳定化特性.研究结果表明:渗滤液回灌准好氧填埋场具有很强的脱氮能力,2号柱由厌氧运行方式改为准好氧条件下,渗滤液中的氨氮和凯式氮浓度分别由最大值的3 198 mg/L和3 345 mg/L降低到第160 d的73 mg/L和81 mg/L,去除率分别为97.7%和97.6%,pH快速升高到8.0左右,COD浓度快速降低.渗滤液中溶解性有机物(DOM)分级结果表明,2号柱HA和FA含量的增加明显快于1号柱.2号柱DOM的三维荧光光谱特性发生了较大变化,荧光基团从60 d结构简单的类蛋白物质转变为95 d结构复杂的类胡敏酸和富里酸物质,而l号柱渗滤液DOM荧光基团一直是结构简单的类蛋白物质.结果表明回灌准好氧生物反应器填埋场的稳定化速度远快于简单回灌的生物反应器填埋场.     

转运站垃圾渗滤液的深度处理及其荧光分析

采用电Fenton法对北京市某垃圾转运站垃圾渗滤液进行深度处理,运用三维荧光光谱技术对电Fenton法氧化前后溶解性有机物(DOM)的荧光特性进行了分析。结果表明,电Fenton法可使COD去除率达到88%以上,NH3-N及色度的去除率接近或等于100%。通过三维荧光特性的测定表明,电Fenton法对大分子的类富里酸有很好的去除效果。     

组合工艺处理填埋场渗滤液中溶解性有机污染物的去除特性

以采用"SBR+混凝+Fenton氧化+BAF"组合工艺处理的晚期垃圾渗滤液各级出水为研究对象,考察了HA、FA和HyI等溶解性有机物(DOM s)在各个工艺处理过程中的变化。结果表明,组合工艺COD和NH3-N去除率分别达到98.4%和99.3%;对DOM s的去除率为98.3%,其中胡敏酸(HA)、富里酸(FA)和亲水性有机物(HyI)的去除率分别为98.3%、99.5%和95.7%。各处理工艺中SBR和混凝工艺对HA和HyI的去除贡献较大,Fenton氧化工艺对FA去除率较高。Fenton氧化和BAF联用,可以有效去除难降解的溶解性有机污染物,使出水达到《生活垃圾填埋污染控制标准》(GB16889-2008)排放标准。     

造纸工业园区污水处理厂溶解性有机物迁移转化规律

在对某造纸工业园区污水处理厂污染物变化规律分析的基础上,采用UV-vis光谱、凝胶色谱和三维荧光等指纹图谱手段对溶解性有机物(DOM)特性进行表征。结果表明,该工业园区污水处理厂能够有效去除以造纸废水为主的混合污水中的有机污染物。UV-vis光谱和凝胶色谱分析表明:水解酸化可将大分子有机物分解成小分子,腐殖化程度降低;高级氧化深度处理后小分子物质所占比例明显增加。三维荧光光谱结果表明,DOM中主要的荧光物质包括色氨酸类蛋白质、芳香族类蛋白质、类腐殖酸、类富里酸物质和酪氨酸类蛋白质。水解酸化可以提高芳香族类蛋白质、类腐殖酸和类富里酸的含量。高级氧化则能有效降低类蛋白质和类腐殖酸物质的含量。     

生物强化组合工艺处理河水的三维荧光及生物多样性分析

通过对受污染地表水进行生物滤池-臭氧预氧化-生物活性炭滤池工艺处理,考察生物强化条件下该项工艺对河水中主要污染物的净化效果,并采用EEM光谱技术进行了溶解性有机物变化和去除规律分析,利用PCR-DGGE技术进行各单元中微生物多样性对比分析。结果表明,生物强化组合工艺系统出水水质主要指标已达到/接近地表水环境质量标准(GB 3838-2002)Ⅳ类限值,生物强化滤池填料中微生物多样性指数和物种数均高于其他工艺单元。受污染河水DOM中主要的荧光物质有类芳香族蛋白质(荧光峰A、B和E)及类腐殖酸(荧光峰C)及类富里酸(荧光峰D),其中,A峰、B峰与E峰的中心位置分别位于225/340 nm、275/336 nm和225/298 nm,各特征荧光峰强度发生明显改变表明,污水中溶解性有机物的含量随系统处理过程而变化。     

垃圾填埋场渗滤液和浓缩液的蒸发特性

研究了垃圾填埋场渗滤液及其MBR-NF-RO处理过程所产生的膜浓缩过滤液在不同蒸馏阶段的水质情况,对比分析了不同pH下渗滤液蒸发情况,考察了蒸发前后的废水中溶解性有机物(DOM)的变化情况。结果表明,垃圾渗滤液蒸发各阶段水质(COD和NH_4~+-N)情况与膜过滤浓缩液大致相同,都是由高到低再升高的情况;在pH 5~10范围内,随着pH的增高,10%残留率下,NH_4~+-N的蒸发量逐渐增加,而TOC逐渐减少;膜过滤浓缩液和垃圾渗滤液的DOM成分大致相同,都以富里酸和腐殖酸为主,蒸发后蒸发液中DOM以类蛋白和色氨酸为主;通过蒸发法处理垃圾渗滤液膜浓缩液,出水水质可以满足《生活垃圾填埋场污染控制标准》(GB16889-2008);而垃圾渗滤液采用此法处理后仍旧含有较高浓度的NH_4~+-N,需结合其他处理设施才可达标排放。     

氨吹脱-两级矿化垃圾-Ac-Fenton处理晚期垃圾渗滤液

采用氨吹脱-两级矿化垃圾床组合工艺处理晚期垃圾渗滤液,对出水中的有机物进行分子质量分布及三维荧光特性分析。针对出水有机物特征及14项出水水质指标,提出联合Ac-Fenton技术进行深度处理,并正交分析深度处理的最佳工艺条件。研究结果表明:两级矿化垃圾床对各分子质量DOM的去除均可达70%~80%,且更易于去除可见区类富里酸,但出水仍以5 k Da的小分子富里酸为主;当活性炭投加量为4.0 g·L~(-1),H2O_2投加量为0.15 mol·L~(-1),H2O_2/Fe2+为2∶1,pH为3.0时,Ac-Fenton工艺处理效能达最佳,此时该组合工艺对色度、COD、BOD5及TN去除效能分别达99.2%、97.6%、97.4%、98.1%,且14项水质指标均能满足GB 16889-2008,实现达标排放。     

城市污水处理过程中溶解性有机物转化特性

运用反渗透技术对城市处理厂进出水中的溶解性有机物(DOM)进行浓缩富集,利用DAX-8大孔树脂将DOM分为亲水物质(Hy I)、类富里酸(FA)和类腐殖酸(HA)3种组分。研究表明,原污水中有机物各组分经生物处理后的总量去除近90%,各组分所占总TOC的百分含量在生化反应过程中也发生了变化:出水中HA组分有降低的趋势,平均下降9.77%,而FA和Hy I两大组分所占总和呈现上升趋势,其中类FA物质升高7.94%,而Hy I组分百分比略有下降。与进水相比,出水中Hy I、FA和HA组分在Ⅲ(色氨酸)、Ⅳ(酪氨酸)区的荧光峰全部消失,而在Ⅰ(类腐殖酸)、Ⅱ(类富里酸)荧光峰变化不大。SUVA和电位滴定结果表明出水有机物的结构发生变化,各组分的芳香性比进水有机物有所增加。研究结果表明,进水中的有机物在污水处理过程中,小分子物质可以被生物利用并形成新的代谢产物释放到水中,大分子物质却较难被生物利用,但在处理过程中其分子构造在一定程度上被微生物改变,系统的生化驯养可以达到构造改变的效果,从而影响出水各组分分子量变化。     

强化混凝-光电氧化组合工艺深度处理垃圾渗滤液膜滤浓缩液

采用强化混凝-光电氧化组合工艺对北京某垃圾填埋场垃圾渗滤液膜滤浓缩液进行处理。探讨了不同混凝剂投加量、电流密度和反应时间对COD去除率的影响,并考察了溶解性有机物的分子量和结构在本工艺中的变化。结果表明:同时投加Ca(OH)2、Fe2(SO4)3和PAM混凝后,COD去除率为28.00%,含量由4 700 mg/L降低到3 384 mg/L;同时投加KMnO4、Fe2(SO4)3和PAM进行二次混凝,COD去除率为60.20%,含量为1 870 mg/L;混凝后水样在电流密度为400A/m2,经3 h光电氧化后,COD去除率为86.20%,含量为650 mg/L。本工艺将垃圾渗滤液膜滤浓缩液中部分大分子量有机物降解为小分子量有机物;光电氧化后,有机物结构被迅速破坏。     

光催化氧化降解垃圾渗滤液中溶解性有机物

研究了UV-TiO2光催化氧化降解垃圾渗滤液过程中溶解性有机物(DOM)的变化特征。结果表明:在适宜条件下,UV-TiO2光催化氧化降解垃圾渗滤液的色度、COD和DOC的去除率分别可达97%、72%和60%;紫外光谱分析说明渗滤液DOM中包括多种含有共轭双键、羰基的大分子有机物及多环芳香类化合物,不同光催化处理液中DOM具有基本一致的结构单元和官能团;红外光谱分析说明渗滤液DOM中含有大量包括羟基、羧基、氨基和苯环的芳香族化合物,在光催化处理液中这几种官能团都能被有效降解;GC/MS分析结果表明,渗滤液DOM中含有72种有机污染物,醇类、羧酸和酮类分别为25、14和12种;在光催化72 h处理液中,有机物减少为44种;酯类和醇类较多,分别为12种和16种;酮类8种,羧酸没有检出。     

不同密度沉水植物腐解过程中水体DOM变化特征

选取白洋淀淀区的泥、水以及晒干的优势沉水植物金鱼藻、轮藻为研究对象,设置6个密度梯度模拟实验,分别于实验进行的50 d和100 d采集水样,运用紫外和荧光光谱技术研究沉水植物腐解阶段水体中溶解性有机质(DOM)的变化。结果显示,同步荧光光谱中,类蛋白峰荧光强度的变化不具规律性,类腐殖质峰荧光强度随密度的增加呈上升趋势,I2/I1的值随着密度的增加或时间的推移均逐渐增大;三维荧光光谱中,随着密度的增加,类富里酸荧光峰A和C的强度逐渐增加,而类色氨酸荧光峰T1的强度变化不大,腐解植物的密度大于3 kg/m3时各组均产生了类海洋腐殖质荧光峰B且强度随密度的增加逐渐增强,C峰的强度与水样中的COD和TP呈显著正相关;紫外光谱测定中,A253/A203的值随着密度的增加或时间的推移而逐渐增大,水体中的芳香族化合物也增多。     

Fenton法处理垃圾渗滤液MBR-NF浓缩液

采用Fenton法处理MBR-NF浓缩液,考察了FeSO4·7H2O投加量、n(H2O2)/n(Fe2+)投加比、初始pH对渗滤液MBR-NF浓缩液处理效果的影响,并在最佳实验条件下,探讨浓缩液富里酸(FA)、亲水性有机物(HyI)组分在Fenton氧化前后组成的变化。研究结果表明,在FeSO4·7H2O投加量为0.055 mol/L、n(H2O2)/n(Fe2+)投加比为4、初始pH为7.58时,对COD、腐植酸(UV254)、色度(CN)的去除率分别为79.6%、93.7%和97.8%。Fenton氧化后,浓缩液中有机物组分含量发生了较大变化,腐植酸含量下降,HyI成为渗滤液溶解性有机物主要成分。紫外-可见光谱表明,Fenton法对FA去除效果较好,而对HyI氧化效果较差;傅立叶红外光谱显示,经Fenton氧化后,FA的结构发生了明显变化,而HyI则变化不明显。     

电-Fenton法预处理干法腈纶生产废水

以Ti金属网为阴极,Ti基RuO2涂层形稳电极为阳极,采用外加H2O2和Fe2+的方式,研究了电-Fenton氧化预处理干法腈纶生产废水的工艺,考察了H2O2投加量、Fe2+投加量、pH值和电流强度等因素对污染物降解过程的影响,分析了废水可生化性和污染物变化规律。结果表明,电-Fenton法可以有效降解废水中有机污染物,使废水COD迅速降低,在初始pH值为3.0,Fe2+投加量为5.0 mmol/L,H2O2投加量为60.0 mmol/L,电流强度0.2 A的条件下,反应120 min后COD去除率可以达到44.0%以上;反应过程中H2O2的投加方式对电-Fenton法的处理效果具有明显影响,H2O2分6次投加可以使COD去除率由一次性投加时的44.8%提高至54.1%;处理后废水的BOD5/COD由0.29升高至0.68;GC-MS结果表明,经电-Fenton法预处理后,废水中多数芳香族化合物和特征污染物能被有效降解。     

Silica removal in industrial effluents with high silica content and low hardness

High silica content of de-inked paper mill effluents is limiting their regeneration and reuse after membrane treatments such as reverse osmosis (RO). Silica removal during softening processes is a common treatment; however, the effluent from the paper mill studied has a low hardness content, which makes the addition of magnesium compounds necessary to increase silica removal. Two soluble magnesium compounds (MgCl₂?6H₂O and MgSO₄?7H₂O) were tested at five dosages (250–1,500 mg/L) and different initial pH values. High removal rates (80–90 %) were obtained with both products at the highest pH tested (11.5). With these removal efficiencies, it is possible to work at high RO recoveries (75–85 %) without silica scaling. Although pH regulation significantly increased the conductivity of the waters (at pH 11.5 from 2.1 to 3.7–4.0 mS/cm), this could be partially solved by using Ca(OH)₂ instead of NaOH as pH regulator (final conductivity around 3.0 mS/cm). Maximum chemical oxygen demand (COD) removal obtained with caustic soda was lower than with lime (15 vs. 30 %). Additionally, the combined use of a polyaluminum coagulant during the softening process was studied; the coagulant, however, did not significantly improve silica removal, obtaining a maximum increase of only 10 %.     

Control of Diesel Gaseous and Particulate Emissions with a Tube-Type Wet Electrostatic Precipitator

Abstract

In this study, experiments were performed with a bench-scale tube-type wet electrostatic precipitator (wESPs) to investigate its effectiveness for the removal of mass- and number-based diesel particulate matter (DPM), hydrocarbons (HCs), carbon monoxide (CO), and oxides of nitrogen (NO_x) from diesel exhaust emissions. The concentration of ozone (O₃) present in the exhaust that underwent a nonthermal plasma treatment process inside the wESP was also measured. A nonroad diesel generator operating at varying load conditions was used as a stationary diesel emission source. The DPM mass analysis was conducted by means of isokinetic sampling and the DPM mass concentration was determined by a gravimetric method. An electrical low-pressure impactor (ELPI) was used to quantify the DPM number concentration. The HC compounds, n-alkanes, and polycyclic aromatic hydrocarbons (PAHs) were collected on a moisture-free quartz filter together with a PUF/XAD/PUF cartridge and extracted in dichloromethane with sonication. Gas chromatography (GC)/mass spectroscopy (MS) was used to determine HC concentrations in the extracted solution. A calibrated gas combustion analyzer (Testo 350) and an O₃ analyzer were used for quantifying the inlet and outlet concentrations of CO and NO_x (nitric oxide [NO] + nitrogen dioxide [NO₂]), and O₃ in the diesel exhaust stream. The wESP was capable of removing approximately 67–86% of mass- and number-based DPM at a 100% exhaust volumetric flow rate generated from 0- to 75-kW engine loads. At 75-kW engine load, increasing gas residence time from approximately 0.1 to 0.4 sec led to a significant increase of DPM removal efficiency from approximately 67 to more than 90%. The removal of n-alkanes, 16 PAHs, and CO in the wESP ranged from 31 to 57% and 5 to 38%, respectively. The use of the wESP did not significantly affect NO_x concentration in diesel exhaust. The O₃ concentration in diesel exhaust was measured to be less than 1 ppm. The main mechanisms responsible for the removal of these pollutants from diesel exhaust are discussed.     

Influence of temperature and origin of dissolved organic matter on the partitioning behavior of polycyclic aromatic hydrocarbons

Background, aim, and scope  

The behavior of polycyclic aromatic hydrocarbons (PAHs) is affected by dissolved organic matter (DOM) present in pore water of soils and sediments. Since partitioning to DOM reduces the bioavailable or freely dissolved PAH concentration in pore water, it is important to assess the effect of environmental variables on the magnitude of dissolved organic matter to water partition coefficients (K _DOC). The objective of this study was to apply passive samplers to measure freely dissolved PAHs allowing depletion from the aqueous phase. The method was applied to determine K _DOC at different temperatures for a selection of PAHs with natural DOM of very different origin.     

氯消毒对城市污水中DOM的三维荧光特性影响

在城市污水二级出水氯消毒过程中,通过对溶解性有机物(DOM)的三维荧光光谱(3DEEM)分析及反应过程中三卤甲烷(THMs)生成量的连续测定,分析各类荧光物质随加氯反应时间的变化规律,探讨其与THMs生成量之间的关系,以此来推测THMs的主要前驱物质。结果表明,加氯后0～6 h内,各反应时间点三维荧光光谱图的等高线的密集程度较原二级出水明显降低,荧光峰的荧光强度减少40%～70%,说明DOM与氯发生反应,芳香构造化程度及不饱程度降低,从而失去荧光特性。其中,简单芳香族蛋白质(酪氨酸类)、腐殖酸类及富里酸类物质在加氯前后荧光强度变化较大,是生成THMs的主要前驱物质。THMs的生成量随反应时间的增加呈现明显的上升趋势,15 min内各类荧光特性有机物的荧光强度减少约50%左右,同时生成了50.17%的THMs。     

Multimedia fate of petroleum hydrocarbons in the soil: Oil matrix of constructed biopiles

A dynamic multimedia fugacity model was used to evaluate the partitioning and fate of petroleum hydrocarbon fractions and aromatic indicator compounds within the soil: oil matrix of three biopiles. Each biopile was characterised by four compartments: air, water, soil solids and non-aqueous phase liquid (NAPL). Equilibrium partitioning in biopile A and B suggested that most fractions resided in the NAPL, with the exception of the aromatic fraction with an equivalent carbon number from 5 to 7 (EC₅₋₇). In Biopile C, which had the highest soil organic carbon content (13%), the soil solids were the most important compartment for both light aliphatic fractions (EC₅₋₆ and EC₆₋₈) and aromatic fractions, excluding the EC₁₆₋₂₁ and EC₂₁₋₃₅. Our starting hypothesis was that hydrocarbons do not degrade within the NAPL. This was supported by the agreement between predicted and measured hydrocarbon concentrations in Biopile B when the degradation rate constant in NAPL was set to zero. In all scenarios, biodegradation in soil was predicted as the dominant removal process for all fractions, except for the aliphatic EC₅₋₆ which was predominantly lost via volatilization. The absence of an explicit NAPL phase in the model yielded a similar prediction of total petroleum hydrocarbon (TPH) behaviour; however the predicted concentrations in the air and water phases were significantly increased with consequent changes in potential mobility. Further comparisons between predictions and measured data, particularly concentrations in the soil mobile phases, are required to ascertain the true value of including an explicit NAPL in models of this kind.