一体化A/O移动床生物膜反应器中DO、TN分布及脱氮效果研究

采用一体化A/O移动床生物膜法工艺，以模拟生活污水研究了该工艺的除碳脱氮效果，并对一体化移动床生物膜反应器的好氧区和缺氧区各纵向断面的COD、DO、NH₃-N、TN、NO^-₃-N和NO^-₂-N进行了检测，通过对缺氧区各断面的DO和TN浓度分布情况，分析了脱氮的产生过程。试验结果表明: 在水力停留时间HRT＝12 h，好氧区DO保持5 mg/L左右，COD进水浓度处于250～400 mg/L时，COD的去除率均在90%以上，且出水COD均在40 mg/L以下；TN进水浓度为20～50 mg/L时，NH₃-N去除率高于90%，其出水浓度可达到5 mg/L以下，脱氮效率也较高，TN去除率可达到65%～85%。COD和NH₃-N的浓度分布状况表明该一体化A/O移动床生物膜反应器的流态趋于全混式。     

UASB反应器厌氧氨氧化菌的脱氮特性研究

研究UASB厌氧氨氧化（ANAMMOX）反应器运行情况，采用普通城市污水厂活性污泥接种，人工合成废水，pH值在7.4～7.8之间，温度控制在(32±1)℃。在反应器稳定运行270～450 d之间的180 d中，对NH⁺₄-N和NO^-₂-N去除率均达到99.9％以上，总氮去除率保持在90％以上，NO^-₃-N产生量在20～30 mg/L之间波动。研究表明,UASB厌氧氨氧化反应器处理废水效果明显，对NH⁺₄-N、NO^-₂-N和TN去除率高，NO^-₂-N和NH⁺₄-N比值可以指示厌氧氨氧化反应器性能的演变。UASB反应器稳定运行阶段容积负荷的影响较小，ANAMMOX菌对合成废水适应性强，反应器抗冲击能力较强，受冲击后恢复迅速。出水pH值稳定在8.5附近，pH值变化情况可作为反应器运行状况的指示。关键词硝化厌氧氨氧化上流式厌氧污泥床生物脱氮     

复合沸石滤床修复北方景观水体的实验研究

以天然矿物质沸石、细砂及煤渣取代传统滤料构建复合基质生态床，表面种植景观植物，采用下向流-上向流运行方式修复北方景观水体。分别进行静态实验及不同循环速率下的动态实验，考察对水体污染物去除过程。结果表明，2种运行方式下对水体NH⁺₄-N去除率都在85%以上，其中以1 h为循环周期的运行方式去除率达97%，较静态提高12.8%；TN去除率最高为84%；TP去除不稳定，过程缓慢。煤渣层对NH⁺₄-N的去除效果差，硝化作用不彻底与反硝化作用的加强使下层出水NH⁺₄-N 、NO^-₂-N及NO^-₃-N浓度均高于上层。提高循环速率有利于对氮的去除。     

pH值控制MAP法脱氮进程的可行性研究

MAP沉淀法处理高NH₃-N废水，操作简便，处理效果好。本试验以NH₃-N浓度为1 000 mg/L的模拟废水为研究对象，研究结果表明，在Mg²⁺∶PO^3-₄∶NH⁺₄=1.2∶1.2∶1（摩尔比）、NaOH投加量为675 g/L的条件下NH₃-N去除率高达98%以上。试验选择出水pH作为控制反应进程的参数，并建立了出水pH与NH₃-N去除率之间的关系。通过调整NaOH投加量控制出水pH在7.5～8之间时，NH₃-N去除率最高，可达98%以上。X-衍射图谱及定量分析表明，沉淀物中MAP的纯度较高，具有一定的回收价值。     

水平潜流人工湿地系统处理微污染原水的研究

采用水平潜流人工湿地系统处理微污染原水，同时考察了水力停留时间、温度、水力负荷以及植物的生长状况等对人工湿地系统处理效果的影响。结果表明，水平潜流人工湿地系统对微污染原水有较好的处理效果，COD、TP、TN、NH⁺₄-N、NO^-₃-N和NO^-₂-N的平均去除率分别为51.55%、49.90%、51.74%、 47.36%、52.67%和63.23%。按照国家地表水环境质量标准（GB3838-2002），经过湿地处理后，出水COD平均值达到Ⅰ类；出水TP平均值达到Ⅱ类；出水TN平均值基本接近Ⅳ类；出水NH⁺₄-N平均值达到Ⅱ类。另外，研究表明, 本系统在水力停留时间为3 d时,水力负荷为0.2 m/d处理效果最好，温度的变化与污染物的去除率呈正相关关系，植物生长旺盛程度直接影响着整个系统的处理效果。     

温度对复合厌氧折流板膜生物反应器处理生活污水效能的影响简

将新型CAMBR反应器（厌氧折流板反应器（ABR）与膜生物反应器（MBR）优化组合）用于处理生活污水，研究温度对该反应器处理效能的影响。实验水力停留时间7.5 h，混合液回流比设置为200%，pH值为6.5~8.5，溶解氧3 mg/L左右。控制3个温度梯度：高温（32~37℃），中温（20~25℃），低温（5~10℃），每个温度运行35 d。结果表明，在高温条件下，系统出水COD、NH₄⁺-N、TN和TP平均浓度分别为25、0.5、12.5和0.7 mg/L。在中温条件下，系统出水COD、NH₄⁺-N、TN和TP浓度分别30、1.2、12.5和0.4 mg/L。在低温条件下，COD和TP分别经过15 d和20 d调整适应，出水可恢复至35 mg/L和1 mg/L。由于低温（10℃以下）对硝化细菌产生强烈抑制，出水NH₄⁺-N去除率最终稳定在35%，TN去除率为40%。低温条件下，该反应器应用于污水处理中需注意适当保温，以保证出水水质。     

污水生物生态处理工艺中的脱氮机理研究

通过水解池-美人蕉湿地、水解/接触氧化池-菖蒲湿地现场实验装置考察了生物-生态工艺深度净化分散生活污水的效果。结果表明,水解池-美人蕉湿地尽管湿地停留时间达到7 d，出水NH⁺₄-N仍难以达到一级A（GB18918-2002）标准；而增加接触氧化池后，湿地停留时间仅2 d，组合工艺出水水质远优于一级A出水要求。美人蕉湿地脱氮的主要途径是湿地微生物的硝化/反硝化，植物吸收约占28%。对经接触氧化处理，NH⁺₄-N、NO^-₃-N浓度均较高的进水，菖蒲湿地可在C/N小于2时高效脱氮。菖蒲湿地对TN的去除占组合工艺TN去除量的79%，其中植物吸收仅占湿地除氮总量的8%。湿地介质的厌氧氨氧化活性试验表明，菖蒲湿地介质表面的微生物在无有机碳源存在的条件下，可使培养液中的NH⁺₄-N与NO^-₃-N、NO^-₂-N短期内发生同步脱氮，厌氧氨氧化可能是菖蒲湿地在进水低碳源条件下脱氮的主要原因。     

SBR-BAF工艺处理效能的试验研究

根据生物除磷和脱氮的机理,污水的脱氮除磷存在基质竞争和泥龄等方面的矛盾。为了分析和解决这个问题，设计开发了一种新的污水生物处理工艺——SBR-BAF复合工艺,并以模拟城市生活污水为处理对象对该工艺的处理效能进行了考察。试验结果表明，系统对COD（不计BAF加入的外碳源）、TP、NH⁺₄-N和TN的平均去除率分别为96%、98%、93%和84%，出水中COD、TP、NH⁺₄-N和TN的平均浓度分别为20、0.23、3.24和7.68 mg/L，各项水质指标均达到《城镇污水处理厂污染物排放标准》（GB 18918-2002 ) 规定的一级标准中的A标准。     

容积负荷对ANAMMOX生物滤池脱氮效能的影响及其基质动力学

采用2套启动成功的上向流厌氧氨氧化（ANAMMOX）生物滤柱，通过调节进水NaNO₂和（NH₄）₂SO₄ 的浓度负荷及水力负荷，改变进水容积负荷，探讨容积负荷对ANAMMOX生物滤柱脱氮效能的影响及其动力学模型。结果表明，滤速恒定条件下，通过提高进水基质浓度来提高进水TN容积负荷，其容积负荷去除动力学过程符合Monod-Haldane基质抑制模型。进水NH₄⁺-N与NO₂^--N浓度分别低于100 mg/L和133 mg/L时，反应器脱氮效果不受明显影响，TN容积去除负荷可达4.21 kg/（m³·d），TN去除率可达80%以上。进水基质浓度恒定条件下，通过提高滤速来提高进水TN容积负荷，其容积负荷去除动力学过程符合零级动力学方程。不受基质浓度抑制的条件下，滤速为3.0 m/h、进水容积负荷为8.82 kg/（m³·d）时，反应器总氮容积负荷去除量可达7.15 kg/（m³·d），总氮去除率可达81.1%。     

利用城市生态河道深度净化污水处理厂出水的工程技术研究

提出了城市生态河道工程构建的技术方法，并研究了示范工程对城市污水处理厂出水的深度净化规律。实验结果表明，在保证生态景观功能的前提下，将生态河道技术工艺用于污水处理厂出水的深度净化，能够高效、稳定地去除氮磷等营养物，河道出水可以满足城市景观水体补充水源的水质要求，出水TP、PO^3-₄、TN、NH₃-N和NO₃-N平均值分别达到0.263、0.116、2.570、0.752和2.438 mg/L，去除率分别达到85.4%、92.8%、60.8%、39.7%和77.2%。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.