全细胞脂肪酶(菌)对SBR系统中微生物群落演替的影响

将具有油脂污水处理功能的全细胞脂肪酶(菌)制剂,直接加入到SBR系统的活性污泥中,应用PCR-DGGE技术的应用,研究该制剂对活性污泥中微生物群落演替的影响。16S rDNA DGGE图谱表明投加全细胞脂肪酶(菌)制剂72h后,菌群丰富度Rs为57%、与空白组的48%相比变化不明显,不同样品相似性系数Cs在48.1%~74.4%之间,表明投加全细胞脂肪酶(菌)对活性污泥中原核微生物群落的演替没有明显影响。18S rDNA DGGE图谱表明,投加全细胞脂肪酶(菌)制剂72 h后,菌群丰富度Rs为72%、与空白组的22%相比存在显著性的差异,不同样品相似性系数Cs在14.5%~73.7%之间,而且优势菌体也发生动态变化,表明投加全细胞脂肪酶(菌)后,对活性污泥中的真核微生物群落演替影响明显。     

解偶联剂与电气石协同作用对污泥性能的影响研究

为提升解偶联剂的污泥减量效果并缓解其对微生物的影响,在序批式活性污泥反应器(SBR)中添加不同浓度的解偶联剂(双香豆素)和电气石,分析两者协同作用对SBR系统中活性污泥产量及性能的影响。研究结果表明,当双香豆素投加量由10mg/L增加到40mg/L,污泥的表观产率由0.19降至0.15,下降约20%,污泥减量作用明显增强,但COD去除率由76.7%下降至76.3%,SBR内的亚硝酸盐氮积累量增加,TN去除率由87.5%降至80.3%,污泥沉降性能有所降低,污泥活性有所提高。40mg/L双香豆素与100g电气石协同作用下,SBR内污泥的表观产率降至0.13,COD去除率提高至82.6%,SBR内亚硝酸盐氮积累量显著降低,TN去除率可达88.9%,污泥沉降性能及污泥活性均有所提高。电气石可以改善高浓度双香豆素所导致的负面影响,不会提高系统污泥产率。     

邻苯二甲酸酯对序批式活性污泥法运行的影响

环境内分泌干扰物邻苯二甲酸酯(PAEs)在废水处理系统中广泛存在,难降解且易产生累积。PAEs的长期积累难以从废水处理工艺上解决。以序批式活性污泥(SBR)工艺处理人工配置的氨氮废水为例,考察PAEs存在条件下对SBR反应器运行的干扰。结果表明:随着原水中PAEs浓度增加,SBR反应器的活性污泥中,微生物最终能够以PAEs为唯一碳源;PAEs为10～150mg/L时,其浓度的变化对SBR反应器内活性污泥性状有明显影响,悬浮固体(MLSS)最终维持在2 000mg/L;随PAEs浓度的改变,SBR反应器内COD去除率变化不显著,而氨氮去除率随着PAEs浓度的升高而降低,最低值约为50%;亚硝态氮出现积累现象,积累量最高时接近60mg/L。     

微生物制剂强化SBR处理系统

应用固定化生物催化剂(IBC)进行SBR处理系统强化实验,考察了IBC的投加对SBR的处理效果和活性污泥的影响。结果表明,投加IBC能够提高SBR的污染物处理效率,相对于对照组,实验组的COD、NH3-N、BOD5和TP去除率分别提高了9.75%、19.36%、6.28%和28.09%。实验组和对照组SVI变化不大,投加微生物制剂IBC并没有显著提高活性污泥的沉降性能。但实验组活性污泥的OUR、SOUR和SBI均高于对照组,这表明IBC的投加提高了SBR中污泥活性,且优化了活性污泥中微生物群落结构。     

长期缺氧吸磷驯化下强化生物除磷系统污泥除磷方式的转化

采用交替厌氧/缺氧/好氧运行的序批式活性污泥反应器(SBR),通过梯度投加电子受体NO_3~-,考察长期缺氧吸磷驯化下强化生物除磷(EBPR)系统的性能及除磷方式的转化。结果表明,当进水COD为300～450mg/L、PO_4~(3-)(以P计,下同)和氨氮分别为8、14mg/L时,驯化期间TN去除率均保持在75%以上,长期缺氧吸磷驯化对COD和氨氮的去除没有影响。硝态氮投加量为5mg/L时,EBPR系统因电子受体投加不足除磷性能迅速恶化,增加硝态氮投加量至10mg/L,经过近30d的恢复,缺氧吸磷率最高可达97.67%,进一步提高硝态氮投加量至15mg/L,系统内硝态氮的积累导致缺氧吸磷率下降。污泥吸磷小试结果表明,经缺氧吸磷驯化后,即使除磷性能欠佳的低浓度电子受体系统污泥也具有良好的反硝化吸磷能力,可见经NO_3~-长期驯化的缺氧吸磷系统有利于筛选以NO_3~-为电子受体的反硝化聚磷菌。     

PACT工艺处理PAM生产废水的实验研究

采用粉末活性炭活性污泥工艺(PACT)处理经凹凸棒土预处理后的聚丙烯酰胺(PAM)生产废水。实验考察了粉末活性炭(PAC)的投加对活性污泥处理系统的影响,并探讨了PAC投加量、曝气时间、水力停留时间等参数对降解反应的影响。结果表明:PAC的投加能提高水中溶解氧的利用率,改善污泥沉降性能,增强活性污泥系统对有机物的去除效果;在PAC投加量500 mg/L、曝气10 h的条件下,PACT工艺对PAM生产废水的处理效果良好,COD的去除率为80.8%,BOD5去除率为83.8%,丙烯酰胺(AM)去除率为84.2%。     

好氧反硝化菌强化序批式活性污泥反应器处理生活污水

研究了好氧反硝化菌强化序批式活性污泥反应器(SBR1)处理生活污水的性能,同时以只接种相同量普通活性污泥的序批式活性污泥反应器(SBR2)作为对照组。结果表明:(1)反应前21天启动期间,SBR1对污水COD、NH+4-N和TN的平均去除率分别可达到77.79%、94.96%、63.21%,对COD和TN的平均去除率明显好于SBR2。(2)当C/N为4∶1(质量比,下同)和6∶1时,SBR1对COD和TN的去除率明显高于SBR2;当C/N为8∶1时,SBR1对COD和TN的去除效果达到最好,对两者的平均去除率分别达到85.31%和61.14%;当C/N为10∶1和12∶1时,两反应器对废水COD去除效果的差距缩小,但SBR1对TN的平均去除率分别为58.98%和51.64%,明显高于SBR2。(3)SBR1投加的好氧反硝化菌适应较低的C/N环境,且能在生活污水中快速增殖,保持了很好的污泥悬浮液浓度和沉降性能,在35d形成成熟的颗粒污泥。     

硝态氮为惟一氮源时异养微生物增长特性

采用SBR研究了缺氧条件下硝态氮为惟一氮源时异养微生物的增长特性。结果表明,异养微生物能利用硝态氮作为氮源进行增殖。当进水COD浓度为1 400 mg/L,硝态氮浓度为280 mg/L时,COD和硝态氮的去除率分别达到97%和99%;污泥中微生物的含氮量为8.8%,低于常规利用氨氮作为氮源的微生物;在实验条件下活性污泥的产率系数为0.30 g VSS/g COD。反硝化菌可利用硝态氮作为氮源进行细胞合成对含硝氮的废水处理具有重要意义。一方面由于无需投加氨氮降低了废水处理成本,另一方面由于污泥产率低,降低了污泥处理成本。     

甜菜碱对肝素钠废水好氧处理的影响

肝素钠废水因含高钠盐而导致其生物处理效率受到较大程度的抑制,对于如何改善高盐下的生物处理效率已成为目前研究的热点。针对SBR工艺处理高盐肝素钠生产废水的好氧生物处理过程,以污泥对有机物、氨氮的去除效率为要点,探讨了甜菜碱对活性污泥性能的影响效果。实验结果表明,(1)当稳定的好氧处理系统受到高钠盐冲击时,投加甜菜碱,TOC的去除率能提高9%~22%,氨氮的去除率能提高9%~16%;(2)当甜菜碱添加浓度为1 mmol/L(即117 mg/L)时,系统污泥性能的改善效果最好,TOC的去除率提高了15.3%,氨氮的去除率提高了18.7%;(3)甜菜碱的一次性添加对活性污泥性能的影响存在一定的持续性,持续时间约为6 d。     

SBR法降解高浓油脂废水的活性污泥菌驯化及小型连续处理

根据高浓度油脂废水生物降解处理采用酵母一级处理-SBR法二级处理的连续净化工艺的要求,使用规模为20 L的SBR反应器对城市生活污水处理用的活性污泥进行强制性驯化,并以驯化的活性污泥菌直接应用于SBR法处理含油废水.实验发现该小型SBR法的工艺技术方案可行,系统抗冲击负荷能力强,整个系统运行比较稳定,对于含高浓度油脂的油脂精练加工厂实际排放污水处理效果良好,油脂和COD的去除率分别连续稳定在95%和90%以上,出水水质指标达到国家一级排放标准的要求.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

红土吸附砷对其动电电位的影响

研究了遵义红土吸附砷对其动电电位的影响 ,从砷酸根浓度和体系pH对红土动电电位影响的角度作了探讨 ,结果表明 ,砷酸根离子浓度越大 ,Zata电位下降幅度越大 ,Zata电位也越低 ;随着体系pH的升高 ,氧化铁胶体动电电位逐渐下降 ,甚至改变了表面电位的符号。由此得出了红土吸附砷属于专性吸附的结论。     

活性炭三维电极法对印染废水的处理研究

对三维电极方法处理印染废水进行了实验研究,初步探讨了活性炭三维电极法处理印染废水的机理,对影响处理效果的各种要素,如反应时间、槽电压和pH值等进行了条件实验,得出了活性炭三维电极法处理印染废水的最佳运行条件为:停留时间120-180 min,槽电压25～30 V,进水pH值6.5～7.5。结果表明,该反应器能有效地降低废水色度,有较高的COD去除效率,并能提高印染废水的可生化性。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.