Identification and assessment of ship emissions and their effects in the harbour of Göteborg,Sweden

The effect of ship emissions in the urban environment of Göteborg has been studied by multivariate analysis. The simultaneous measurements of relevant gases and sub-micron particles make identification of ship plumes possible. Increased concentrations of these species due to ship emissions are quantified for ships entering the inner part of the harbour. Annual depositions of SO₂ and NO₂ are estimated to be 220 and 115 kg km⁻² yr⁻¹, respectively. Exposure of transient particles (less than 0.1 μm in diameter) to this part of the harbour increased by a factor of 3 in number concentration when a ship plume was recorded. Ni, Pb, V and Zn are shown to have positive correlation with NO emissions from ships.     

Comparison of line– and point–source releases of tracer gases

Field measurements were made of greenhouse gas emissions from a wastewater treatment system using open path monitoring with detection by FTIR spectroscopy. Emission rates were determined by the ratio technique using a sulfur hexafluoride tracer gas released from a line source. As a quality control check, a second tracer gas – ethylene – was released from various single point locations. This paper presents a comparison of the line-source and point-source tracer releases for approximating emissions from the area source. The two types of tracer release showed excellent agreement when both release points were two hundred meters from the FTIR beam path. Data for other release points also were comparable, once differences in vertical dispersion as a function of distance are taken into account.     

Environmental hazard — Assessment of chemicals and products

Part III: The Limits to Single Compound Assessment The principles and basic assumptions of single compound assessment are briefly reviewed. Limitations to this approach are shown, especially with regard to complex mixtures of similar substances, substitution products, and complicated (final) products containing chemicals and materials produced by the chemical industry. A new thinking in product lines and life cycles is emerging, leading to new assessment methods. In some cases, substitution has not improved the environmental performance of products, since very similar chemicals were used as substitutes.     

Lethal and sublethal effects of the natural and healthy spinosad-based formulation Tracer™ on tadpoles of two neotropical species

Environmental Science and Pollution Research - This paper presents the first acute toxicity data of the natural insecticide spinosad in amphibians. The sensitivity of two neotropical sympatric...     

Sources and concentrations of gaseous and particulate reduced nitrogen in the city of Münster (Germany)

Atmospheric ammonia mixing ratios and the main inorganic ions NH₄⁺, NO₃⁻ and SO₄²⁻ of size-resolved particles in the range from 0.05 to 10 μm were measured at an urban site in Münster, Germany. High mixing ratios of ammonia with a median of 5.2 ppb and a maximum of 50 ppb were detected. The mass fraction of submicron particles was much higher during the day than at night. At night, a greater particle mass and an increased presence of particulate nitrate was measured. Recurring patterns of particle distribution were distinguished and their characteristics analysed. In half of the measurements, the accumulation mode was clearly dominating, which is an indication of aged aerosol. In some measurements, higher concentrations of fine particles were found indicating particle formation. In these cases, a smaller particle mass and about four times greater ratios of ammonia versus ammonium concentrations were observed. These data show that ammonia contributes considerably to the formation of secondary particulate material.     

Concentrations of heavy metal and radioactivity in surface water and sediment of Hazar Lake (Elaziğ, Turkey)

Concentration of heavy metals and natural gross radioactivity were measured in the surface water and sediment of Hazar Lake (Elazi?, Turkey). Eight sampling sites were pre-defined in different locations of the lake. A preliminary study on heavy metals (Zn, Fe, Mn, Ni, Cu, Cr, Co and Pb), major elements (Na, K, Ca, Mg) concentrations and natural radioactivity related to 226Ra, gross-alpha and gross-beta radiations in the surface water and deep sediments were determined. The obtained results showed that, in general, the heavy metals (Zn, Fe, Mn, Ni, Cu and Pb) and major elements (Na, K, Ca, Mg) concentrations in water did not exceed WHO (World Health Organization, 1999), EC (Europe Community, 1998), EPA (Environment Protection Agency, 2002) and TSE-266 (Turkish Standard, 1997) guidelines. Generally, heavy metals and major elements concentration of the sediments were found decrease in sequence of Fe>Mg>Ca>Mn>Zn>Ni>Cr>Cu>Co>Pb. The results of this study indicated that a general absence of serious pollution in the Hazar Lake. The results obtained from the radioactivity determination indicate that the surface water radioactivity concentration of 226Ra, gross-alpha and gross-beta were ranging from 0.52+/-0.02 to 2.02+/-0.06 Bq/l and from 0.65+/-0.03 to 2.52+/-0.07 Bq/l and from 0.01+/-0.01 to 0.14+/-0.01 Bq/l, respectively. Deep sediment radioactivity concentrations of 226Ra is ranging from 0.07+/-0.03 to 0.32+/-0.07 Bq/g.     

Determination and evaluation of cadmium, lead and nickel in greenhouse soils of Almería (Spain)

This study determines total levels of three (Cd, Pb and Ni) potentially toxic trace elements in western Almería (Spain) greenhouse surface soil horizons using microwave digestion; it establishes the geochemical baseline concentration, and it investigates possible relationships between soil properties and elemental concentrations. The results show that the soil concentration of these heavy metals is lower than mentioned in the European and Spanish normative, but they are higher than those reported by other authors working on agricultural soils. The obtained geochemical baseline concentrations (mg kg(-1)) were: Cd 0.4-0.8, Pb 2.5-89.9 and Ni 16.1-30.7. Using the upper baseline criterion, 88% of greenhouse soils have relatively higher content of heavy metals because of their Cd, Pb and Ni concentration. Moreover, soil properties are related to heavy metals contents suggesting that among Cd, Pb and Ni have a similar origin and those total metal concentrations are controlled primarily by soil compositions.     

Correlating the trends of COVID-19 spread and air quality during lockdowns in Tier-I and Tier-II cities of India—lessons learnt and futuristic strategies

Environmental Science and Pollution Research - The present study focuses on the impact of early imposed lockdowns and following unlocking phases on the status of air quality in six Tier-I and nine...     

An on-farm survey of spatial and temporal stratifications of 17β-estradiol concentrations

17β-estradiol (E2) is a natural estrogenic hormone found in animal manure and urine, which may cause endocrine disruption in sensitive organisms. 17β-Estradiol has been widely detected in the environment, and animal agriculture may be an important source. The objectives of this study were to investigate the potential sources and/or spatial and temporal characteristics contributing to detections of E2 at the farm-scale. Soil cores, segmented into 0.15 m increments, were taken down to the water table from four locations (three potential E2 sources and one control) at or around a swine (Sus scrofa domesticus) farm on five different dates between 2006 and 2007. Estradiol was quantified in the soil-water extracts using liquid chromatography-with tandem mass spectrometry (LC/MS/MS) analysis. Estradiol detections were widespread and found in 128 out of 345 extractions (37%). Concentrations ranged from 0 to 1910 ng L⁻¹ (porewater equivalents). A location that received field application of manure had significantly lower E2 concentrations compared to other locations. Also, the spring 2007 E2 concentrations were significantly higher than all other sample dates, perhaps related to climatic and hydrological events. Results suggested E2 was not directly related to manure sources, but was widespread in this environment. Where E2 was detected, highest concentrations favored the upper profile, while the greatest frequency of detections was in the lower profile and near the water table. Detections of E2 were associated with high organic mater contents in the upper profile and high sand contents in the lower profile. The study suggests that E2 is widespread in some soil environments, raising questions as to the source and mechanisms that facilitate its transport and mobility.     

The photochemical formation and gas–particle partitioning of oxidation products of decamethyl cyclopentasiloxane and decamethyl tetrasiloxane in the atmosphere

Decamethyl cyclopentasiloxane (D₅) and decamethyl tetrasiloxane (MD₂M) were injected into a smog chamber containing fine Arizona road dust particles (95% surface area <2.6 μM) and an urban smog atmosphere in the daytime. A photochemical reaction – gas–particle partitioning reaction scheme, was implemented to simulate the formation and gas–particle partitioning of hydroxyl oxidation products of D₅ and MD₂M. This scheme incorporated the reactions of D₅ and MD₂M into an existing urban smog chemical mechanism carbon bond IV and partitioned the products between gas and particle phase by treating gas–particle partitioning as a kinetic process and specifying an uptake and off-gassing rate. A photochemical model PKSS was used to simulate this set of reactions. A Langmuirian partitioning model was used to convert the measured and estimated mass-based partitioning coefficients (K_P) to a molar or volume-based form. The model simulations indicated that >99% of all product silanol formed in the gas-phase partition immediately to particle phase and the experimental data agreed with model predictions. One product, D₄TOH was observed and confirmed for the D₅ reaction and this system was modeled successfully. Experimental data was inadequate for MD₂M reaction products and it is likely that more than one product formed. The model set up a framework into which more reaction and partitioning steps can be easily added.     

Chemistry of fog waters in California's Central Valley—Part 3: concentrations and speciation of organic and inorganic nitrogen

Although organic nitrogen (ON) has been found to be a ubiquitous and significant component in wet and dry deposition, almost nothing is known about its concentration or composition in fog waters. To address this gap, we have investigated the concentration and composition of ON in fog waters collected in Davis, in California's Central Valley. Significant quantities of dissolved organic nitrogen (DON) were found in these samples, with a median concentration of 303 μM N (range=120–1630 μM N). DON typically represented approximately 16% of the total dissolved nitrogen (inorganic+organic) in Davis fog waters. The median concentration of nitrogen in free amino acids and alkyl amines was 16 μM N (range=3.8–120 μM N), which accounted for 3.4% of the DON in Davis fogs. Thus, although the absolute concentrations of free amino compounds were significant, they were only a minor component of the DON pool. Combined amino nitrogen (e.g., proteins and peptides) was present at higher concentrations and accounted for 6.1–29% (median=16%) of DON. Overall, free and combined amino compounds typically accounted for a median value of 22% of DON in the fog waters.The high concentrations of DON found, and the fact that amino and other N-containing organic compounds can serve as nitrogen sources for microorganisms and plants, indicate that atmospheric ON compounds likely play an important role in nitrogen cycling in the Central Valley. In addition, due to the basicity of some N functional groups, ON compounds likely contribute to the previously observed acid buffering capacity of Central Valley fog waters. Finally, a comparison of fog waters with fine particles (PM_2.5) collected from the same site during the same period of time indicated that the median concentrations (mol N m⁻³-air) of total water-soluble ON, free amino nitrogen and total amino nitrogen were very similar in the fog water and PM_2.5. Given the high water solubility of many organic N compounds, this result suggests that ON might contribute to the hygroscopic properties of atmospheric particles.     

Preparation of calcium oxalate—bromopyrogallol red inclusion sorbent and application to treatment of cationic dye and heavy metal wastewaters

Background, aim, and scope  Dye pollutants are a major class of environmental contaminants. Over 100,000 dyes have been synthesized worldwide and more than 700,000 tons are produced annually and over 5% are discharged into aquatic environments. The adsorption or sorption is one of the most efficient methods to remove dye and heavy metal pollutants from wastewater. However, most of the present sorbents often bear some disadvantages, e.g. low sorption capacity, difficult separation of spoil, complex reproduction, or secondary pollution. Development of novel sorbents that can overcome these limitations is desirable. Materials and methods  On the basis of the chemical coprecipitation of calcium oxalate (CaC₂O₄), bromopyrogallol red (BPR) was embedded during the growing of CaC₂O₄ particles. The ternary C₂O₄ ^2––BPR–Ca²⁺ sorbent was yielded by the centrifugation. Its composition was determined by spectrophotometry and AAS, and its structure and morphology were characterized by powder X-ray diffraction (XRD), laser particle-size analysis, and scanning electron microscopy (SEM). The adsorption of ethyl violet (EV) and heavy metals, e.g. Cu(II), Cd(II), Ni(II), Zn(II), and Pb(II) were carried out and their removal rate determined by spectrophotometry and ICP-OES. The adsorption performance of the sorbent was compared with powder activated carbon. The Langmuir isothermal model was applied to fit the embedment of BPR and adsorption of EV. Results  The saturation number of BPR binding to CaC₂O₄ reached 0.0105 mol/mol and the adsorption constant of the complex was 4.70 × 10⁵ M^–1. Over 80% of the sorbent particles are between 0.7 and 1.02 μm, formed by the aggregation of the global CaC₂O₄/BPR inclusion grains of 30–50 nm size. Such a material was found to adsorb cationic dyes selectively and sensitively. Ethyl violet (EV) was used to investigate the adsorption mechanism of the material. One BPR molecule may just bind with one EV molecule. The CaC₂O₄/BPR inclusion material adsorbed EV over two times more efficiently than the activated carbon. The adsorption of EV on the CaC₂O₄/BPR inclusion sorbent was complete in only 5 min and the sedimentation complete in 1 h. However, those of EV onto activated carbon took more than 1.5 and 5 h, respectively. The treatment of methylene blue and malachite green dye wastewaters indicated that only 0.4% of the sorbent adsorbed over 80% of color substances. Besides, the material can also adsorb heavy metals by complexation with BPR. Over 90% of Pb²⁺, and approximately 50% of Cd²⁺ and Cu²⁺, were removed in a high Zn²⁺-electroplating wastewater when 3% of the material was added. Eighty-six percent of Cu²⁺, and 60% of Ni²⁺ and Cd²⁺, were removed in a high Cd²⁺-electroplating wastewater. Discussion  The embedment of BPR into CaC₂O₄ particles responded to the Langmuir isothermal adsorption. As the affinity ligand of Ca²⁺, BPR with sulfonic groups may be adsorbed into the temporary electric double layer during the growing of CaC₂O₄ particles. Immediately, C₂O₄ ^2– captured the Ca²⁺ to form the CaC₂O₄ outer enclosed sphere. Thus, BPR may be released and embedded as a sandwich between CaC₂O₄ layers. The adsorption of EV on the sorbent obeyed the Langmuir isothermal equation and adsorption is mainly due to the ion-pair attraction between EV and BPR. Different from the inclusion sorbent, the activated carbon depended on the specific surface area to adsorb organic substances. Therefore, the adsorption capacity, equilibrium, and sedimentation time of the sorbent are much better than activated carbon. The interaction of heavy metals with the inclusion sorbent responded to their coordination. Conclusions  By characterizing the C₂O₄ ^2––BPR–Ca²⁺ inclusion material using various modern instruments, the ternary in situ embedment particle, [(CaC₂O₄)₉₅(BPR)] _n ^2n–, an electronegative, micron-sized adsorbent was synthesized. It is selective, rapid, and highly effective for adsorbing cationic dyes and heavy metals. Moreover, the adsorption is hardly subject to the impact of electrolytes. Recommendations and perspectives  The present work provides a simple and valuable method for preparing the highly effective adsorbent. If a concentrated BPR wastewater was reused as the inclusion reactant, the sorbent will be low cost. By selecting the inclusion ligand with a special structure, we may prepare some particular functional materials to recover the valuable substances from seriously polluted wastewaters. The recommended method will play a significant role in development of advanced adsorption materials. Electronic supplementary material  The online version of this article (doi:) contains supplementary material, which is available to authorized users.     

Characterization of the toxic effects of cadmium and 3.5-dichlorophenol on nitrifying activity and mortality in biologically activated sludge systems—effect of low temperature

Background, aims, and scope  Sometimes, urban wastewaters convey a more or less significant part of toxic products from industries or the craft industry. Nitrifying activity can be affected by these substances, implying higher ammonia concentrations in the outlet effluent and contributing to toxicity for the aquatic environment. Moreover, the more stringently treated wastewater standards now require a reliable treatment for nitrogen. One of the key issues is the identification of the inhibition behavior of nitrifying bacteria facing a toxic substance. This new understanding could then finally be integrated into models in order to represent and to optimize wastewater treatment plants (WWTP) operation in cases involving ‘toxic scenarios’. Materials and methods  The toxic substances studied in this work, cadmium and 3.5-dichlorophenol (3.5-DCP), are representative of chemical substances commonly found in municipal sewage and industrial effluents and symbolize two different contaminant groups. The effects of Cd and 3.5-DCP on nitrification kinetics have been investigated using respirometry techniques. Results  IC50 values determination gives concentrations of 3.1 mg/L for 3.5-DCP and 45.8 mg/L for Cd at 21 ± 1°C. The variation to low temperature seems to have no real effect on IC50 for DCP, but induces a decrease of cadmium IC50 to 27.5 mg/L at 14°C. Finally, specific respirometric tests have been carried out in order to determine the potential effect of these toxic substances on the nitrifying decay rate b _a . No significant effect has been noticed for Cd, whereas the presence of 3.5-DCP (at IC50 concentration) induced a dramatic increase of b _a at 20°C. The same behavior has been confirmed by experiments performed in winter periods with a sludge temperature around 12°C. Discussion  The target substances have different modes of action on activity and mortality, notably due to the abilities of the contaminant to be precipitated, accumulated, or even to be progressively degraded. Studies realized at low temperature confirmed this assumption, and put in evidence the effect of temperature on toxic substances capable of being biosorbed. However, the change in the sludge sample characteristics can be pointed out as a problem in the investigation of the temperature effect on nitrification inhibition, as biosorption, bioaccumulation, and predation are directly linked to the sludge characteristics (VSS concentration, temperature) and the plant operating conditions (loading rates, sludge age, etc.). Conclusions  This work brings new understandings concerning the action mode of these specific contaminants on nitrifying bacteria and, in particular, on the role of temperature. The experiments lead to the determination of the IC50 values for both toxic substances on biological nitrification. The inhibition mechanisms of Cd and 3.5-DCP on nitrifying activity have been simply represented by a non-competitive inhibition model. Recommendations and perspectives  Other experiments carried out in a continuous lab-scale pilot plant should be done with a proper control of the operating conditions and of the sludge characteristics in order to better understand the mechanisms of nitrification inhibition for each contaminant. Finally, these first results show that toxic substances can have an effect on the growth rate but also on the decay rate, depending on the characteristics of the toxic substance and the sludge. This eventual double effect would imply different strategies of WWTP operation according to the behavior of the contaminant on the bacteria.     

Effect thresholds and ‘Adequate Control’ of risks

BACKGROUND: Preparation of the new European REACH (Registration, Evaluation and Authorisation of CHemicals) regulation on chemicals has reached a critical stage. Depending on how key elements of the legislative proposal are finalised, especially that on authorisation of uses of 'substances of very high concern', REACH could either provide an effective measure to drive innovation towards cleaner and safer alternatives, or instead lead to further avoidable chemical exposures on the basis of demonstrated 'adequate control' of risks. Given that some key indicators of human and wildlife reproductive health continue to decline in parts of Europe, while evidence for chemical exposure as a contributory factor grows, it will clearly be vital to get the legislation right. GOAL AND SCOPE: Whereas there is now a consensus between the European Parliament and Council of the European Union that uses of persistent, bioaccumulative and toxic (PBT) and very persistent and very bioaccumulative (vPvB) substances should only be permitted when no safer alternatives are available, major differences remain regarding the manner in which other 'substances of very high concern' (including substances which are carcinogenic, mutagenic or toxic to reproduction (CMRs) and endocrine disruptors) are addressed. This paper examines those differences in more detail and proposes some ways forward. METHODS: Using case studies of specific chemicals as examples, the paper critically evaluates the concepts of 'effect thresholds' and 'adequate control' of risks, which underpin the Council's proposal for many CMRs and endocrine disruptors. RESULTS: The subjectivity and uncertainties inherent in the threshold approach proposed by the Council, as illustrated by these case examples, bring its ability to ensure a high level of protection for the environment and human health into question: i. the nature and extent of toxic effects recorded depend on many different factors, including the type of test and conditions selected, the organisms exposed, the timing of exposure and precisely which effects are measured and over what timeframe. ii. doses considerably below 'no effect levels' for survival could nevertheless be causing significant impairment to health and/or reproductive success. iii. chemicals present in mixtures at levels below established thresholds for effects may, in combination, induce significant toxicological responses. DISCUSSION: Under the Council's current proposal, companies will be granted authorisations for some uses of CMRs and endocrine disruptors, even if safer alternatives without these properties are already on the market. The high level of evidence required for identification of substances as being of equivalent concern represents an additional weakness in the Council approach. CONCLUSIONS: Instead, a requirement (along the lines of the Parliament's proposals) to address the availability of alternatives in all cases, to use them when available and to initiate their development when not, represents a more robust, defensible and protective approach to the management of 'substances of very high concern'. The possibility for authorisation of essential uses would remain, while all avoidable uses and exposures would progressively be prevented and sustainable innovation supported. PERSPECTIVES: In the long run, this can only lead to a more sustainable future for the chemical industry in Europe, as well as delivering benefits of increased protection for our environment and health for generations to come.     

Effectiveness of UV/SO32− advanced reduction process for degradation and mineralization of trichlorfon pesticide in water: identification of intermediates and toxicity assessment

Environmental Science and Pollution Research - This study aimed to investigate the degradability, mineralization, proposed decomposition pathway, intermediate products, and toxicity of effluent...     

Crystal structure of δ-isobutoxypentabromo-cyclododecanes, kinetics and selectivity of their isomerization during thermal treatment of flame-proofed polystyrenes

Hexabromocyclododecanes (HBCDs) are persistent organic pollutants now ubiquitous in the environment. Technical HBCD mixtures and with it flame-proofed polystyrenes (FP-PS) also contain isobutoxypentabromocyclododecanes (iBPBCDs) as minor constituents, which are possibly released together with HBCDs. So far, eight diastereomeric pairs of enantiomers named as α-, β-, γ-, δ-, ?-, ξ-, η-, and θ-iBPBCDs with proportions of 10%, 5%, 2%, 21%, 11%, 11%, 12% and 28% were found in technical HBCD. Herein the crystal structure of racemic δ-iBPBCD, the second most prominent diastereomer, is presented and assigned to (1S)-1-isobutoxy-(2R,5R,6S,9S,10S)-2,5,6,9,10-pentabromocyclododecane and its enantiomer. During thermal treatment of FP-PS, e.g. the production of extruded polystyrenes (XPS), proportions of δ-iBPBCDs decrease and those of other stereoisomers increase. Evidence was found that δ-iBPBCDs isomerize stereo- and regioselectively to β-iBPBCDs. Based on structural and kinetic data, a transformation mechanism was proposed. Apparent first-order rate constants (k_iso) of 0.0019, 0.0050, and 0.012 min⁻¹ are found for the δ- to β-iBPBCD isomerization at 120, 130, and 140 °C, respectively, corresponding to half-lives of 360, 140, and 56 min. These transformations also occur during the production of XPS, which predominantly contain β-iBPBCDs, whereas δ-iBPBCDs dominate in materials experiencing lower thermal stress, e.g. expanded polystyrenes (EPS). The relative configurations of δ- and θ-iBPBCDs are TtCtCt, like the one of γ-HBCDs. γ-HBCDs are the kinetically and α-HBCDs with a TcCtCc configuration the thermodynamically favored products. In analogy, β-iBPBCDs are assumed to have a TcCtCc configuration like α-HBCDs because they are formed from δ-iBPBCDs under thermodynamic control. In conclusion, HBCD- and iBPBCD-patterns in flame-proofed polystyrenes vary substantially, reflecting the thermal stress these materials have experienced. When released to the environment, these patterns might further change, as observed for HBCDs.     

Identification of new ozonation disinfection byproducts of 17β-estradiol and estrone in water

Estrogens are a class of micro-pollutants found in water at low concentrations (in the ng L⁻¹ range), but often sufficient to exert estrogenic effects due to their high estrogenic potency. Disinfection of waters containing estrogens through oxidative processes has been shown to lead to the formation of disinfection byproducts, which may also be estrogenic. The present work investigates the formation of disinfection byproducts of 17β-estradiol (E2) and estrone (E1) in the treatment of water with ozone. Experiments have been carried out at two different concentrations of the estrogens in ground water (100 ng L⁻¹ and 100 μg L⁻¹) and at varying ozone dosages (0-30 mg L⁻¹). Detection of the estrogens and their disinfection byproducts in the water samples has been performed by means of ultra performance liquid chromatography-tandem mass spectrometry (UPLC-MS/MS) with a triple quadrupole (QqQ) and a quadrupole-time of flight (QqTOF) instrument. Both E2 and E1 have been found to form two main byproducts, with molecular mass (MM) 288 and 278 in the case of E2, and 286 and 276 in the case of E1, following presumably the same reaction pathways. The E2 byproduct with MM 288 has been identified as 10epsilon-17beta-dihydroxy-1,4-estradieno-3-one (DEO), in agreement with previously published results. The molecular structures and the formation pathways of the other three newly identified byproducts have been suggested. These byproducts have been found to be formed at both high and low concentrations of the estrogens and to be persistent even after application of high ozone dosages.     

Rapid photodegradation and detection of zolpidem over β-SnWO4 and α-SnWO4 nanoparticles: optimization and mechanism

Environmental Science and Pollution Research - We reported the tin (II) tungstate nanoparticles as the photocatalyst and sensor modifier that were synthesized via chemical precipitation reaction...     

Magnetic photocatalysts from δ-FeOOH and TiO2 and application in reactions for degradation of methylene blue and paracetamol with UV-C and sunlight

Environmental Science and Pollution Research - Water contamination is a common problem, especially considering dyes and drugs disposal. A possible and effective treatment method to remove these...     

Concentrations of phthalate esters and identification of other additives in PVC children’s toys

This study was intended to provide data on the composition of soft PVC toys, addressing the widest practicable range of chemical additives and including non-phthalate additives. The study also included toys from as many countries as possible, since for many, no data were available. A total of 72 toys were purchased in 17 countries. The majority (64) were PVC or had PVC sections. In almost all the soft PVC toys analysed, phthalates comprised a sizeable proportion (most frequently 10–40%) of the total weight of the toy. The predominant phthalates detected were diisononyl phthalate (DINP) and di(2-ethylhexyl) phthalate (DEHP). Other phthalates identified in high concentrations in some toys include isomeric mixes of diisooctyl phthalate (DIOP) and diisodecyl phthalate (DIDP). The estrogenic chemical nonylphenol was isolated from 13 toys, while 2 toys were found to contain the fungicide Fungitrol 11 (Folpet). 78% of PVC toys contained one or more extractable organic compounds in addition to those reported above. Some of these data have been released previously by Greenpeace and made available on the internet.This report, however, which is intended for a technically expert audience, has been peer reviewed and contains further analytical data that have not been published before.