低温型复合发酵菌剂接种鸡粪堆肥的效应

以鲜鸡粪为主要材料,进行了低温启动型复合发酵菌剂在低温环境下的堆肥发酵试验,研究分析了发酵过程堆肥的温度、水分、pH值、C/N、灰分、NH~+_4-N和有机质含量的变化。结果表明:在15℃条件下,研制的发酵菌剂可使鸡粪堆肥在24 h内启动发酵,提早启动2 d以上,堆温达到50℃以上的时间提前5 d左右,维持55℃以上高温达到14 d,低温启动效果明显,且堆温较高;可加快堆肥物料水分的挥发,降低C/N比,发酵15 d后种子发芽指数达到80.4%,比对照提前12 d,发酵进程显著加快;虽然堆肥有机质的损失率略高于对照,但全氮的损失率却低于对照,堆肥铵态氮的含量提高70.2%,保氮效果显著。     

复合腐秆菌剂对稻草腐熟过程的影响

为了研究复合腐秆菌剂对稻草好氧堆肥的影响,采用好氧堆肥技术,设计了不接菌(对照)和接种复合菌剂2个处理,探讨堆肥过程中堆体温度、pH、有机质、C/N、发芽指数的变化。结果表明,接种复合腐秆菌剂堆体初期温度上升迅速,最高温度达到60℃,高温发酵阶段维持了12 d;与对照相比,接种复合腐秆菌剂对pH值、容重与孔隙度、有机质、C/N变化影响不大;但增加堆体全氮的含量,提高堆肥产品的质量,种子发芽率在第20天迅速上升,最大值为93%。显然接种复合腐秆菌剂促进好氧堆肥迅速起温,提高了堆肥的腐熟质量。     

添加VT菌剂和有机物料腐熟剂对堆肥的影响

通过在高温好氧堆肥中分别添加VT菌剂和有机物料腐熟剂,研究接种3‰的VT菌剂和有机物料腐熟剂促进堆肥的作用效果。结果表明,接种VT菌剂的处理与空白和接种有机物料腐熟剂的处理相比,堆肥初期升温更快;高温期更长;堆肥结束时,C/N降低的多,NO3-N增加的多,NH4+-N挥发的少,接种VT菌剂和VT有机物料腐熟剂都可促进有机质的充分降解,缩短堆肥时间,加快堆肥腐熟,提高堆肥肥力。     

添加VT菌剂和有机物料腐熟齐对堆肥的影响

通过在高温好氧堆肥中分别添加VT菌剂和有机物料腐熟剂，研究接种3％o的VT菌剂和有机物料腐熟剂促进堆肥的作用效果。结果表明，接种VT菌剂的处理与空白和接种有机物料腐熟剂的处理相比，堆肥初期升温更快；高温期更长；堆肥结束时，C／N降低的多，NO3-N增加的多，NH4-N挥发的少，接种VT菌剂和VT有机物料腐熟剂都可促进有机质的充分降解，缩短堆肥时间，加快堆肥腐熟，提高堆肥肥力。     

接种外源微生物菌剂对香蕉茎秆堆肥的影响

为了研究接种外源微生物菌剂对香蕉茎秆堆肥的影响,本实验采用高温好氧堆肥技术,设计了对照（不接菌）、接种白腐菌及棱盖多孔菌3个处理,探讨了不同处理堆肥过程中堆体温度、水分、pH值、电导率、有机碳、C/N、发芽指数及堆肥质量的变化情况。结果表明,接种微生物菌剂处理的温度均高于对照,且高温期持续时间相对较长,以接种白腐菌处理的高温持续时间最长;接种外源微生物菌剂对堆肥含水率、pH、EC、全碳、C/N变化影响不大;与对照相比,接种白腐菌可增加全氮及全钾的含量,有利于提高堆肥产品质量;接种白腐菌处理在36 d（GI〉50%）就达到腐熟,比对照提前8 d腐熟,明显缩短堆肥腐熟时间;而接种棱盖多孔菌处理比对照推迟10 d腐熟,共需54 d不利于香蕉茎秆堆肥的进行。     

调理料添加比例对菇渣基质发酵效果的影响

为探讨废弃蘑菇基料菇渣改性生产有机栽培基质技术,直接采用菇渣为主要原料,以猪粪作为调理料进行好氧发酵,研究猪粪的不同添加比例对菇渣好氧发酵腐熟条件中的温度、挥发性固体(VS)、p H、全氮、全磷、种子发芽指数(GI)的影响。结果表明,猪粪适宜作为菇渣改性生产有机基质的调理料,发酵过程始终维持含水率在65%左右,3个处理高温持续时间均在5 d以上,满足基质无害化卫生标准要求,发酵完成后p H均符合腐熟基质标准,GI均达到60%以上。而猪粪添加量较少时,可以缩短进入高温发酵期的时间,堆体达到的最高温度较高,堆料腐熟较快,且最有利于氮素的保存和全磷的浓缩。综合以上实验结果表明,在菇渣发酵中添加15%的猪粪有利于改善发酵条件,提高堆体的养分含量。     

添加小麦秸秆对猪粪高温堆肥腐熟进程的影响

选用猪粪与小麦秸秆为堆肥原料进行高温好氧堆肥实验,研究添加小麦秸秆对猪粪高温好氧堆肥过程中堆体温度、pH值、种子发芽指数、碳氮比和养分等理化指标的影响,寻求猪粪高温堆肥时的最佳秸秆配比,旨在为猪粪快速资源化利用提供科学依据。结果表明,猪粪高温堆肥时添加小麦秸秆可以缩短进入高温发酵阶段的时间,减少氮素损失,加快C/N的降低速率,加速有毒有害物质分解。其中猪粪和小麦秸秆6∶4处理各层温度在2~5 d内上升至50℃,并持续37~46 d,在堆肥结束时,有机质和速效氮含量较堆肥初期下降幅度最小,分别为33.90%和23.76%,全氮、全磷、全钾、速效磷和速效钾含量较堆肥初期提高幅度最大,分别为13.34%、20.24%、53.19%、41.53%和16.57%。若以种子发芽指数80%作为堆肥腐熟的评价指标,猪粪和小麦秸秆6∶4配比堆肥的腐熟速度比纯猪粪快18 d,36 d即可腐熟。综合判断,实际应用中,猪粪与小麦秸秆按体积6∶4进行堆肥较为适宜。     

添加外源纤维素酶对水稻秸秆模拟堆肥过程的影响

利用水稻秸秆模拟堆肥,对纤维素、半纤维素质量分数及堆肥相关指标随添加外源纤维素酶的变化进行研究。结果表明,与不加酶堆肥相比,添加外源纤维素酶显著提高了水稻秸秆纤维素及半纤维素的降解率,其降解趋势均可用一阶指数衰减方程拟合;堆肥结束时,添加纤维素酶处理的堆肥纤维素质量分数较不加酶处理低35.1%。纤维素酶促进了堆肥中腐殖酸的合成,提高了堆肥中的铵态氮(NO3-N)、硝态氮(NH4-N)及全氮(TN)的质量分数,并导致堆肥中碳素质量分数下降,C/N质量比下降了23.1%;添加纤维素酶进一步降低了堆肥的生物毒性,使得发芽指数提高了10.3%。外源添加纤维素酶加快了水稻秸秆堆肥的腐熟进程。     

二丁与连翘药渣联合堆肥腐熟度评价

为了对不同比例的二丁与连翘药渣堆肥腐熟度进行评价,采用条垛式好氧堆肥方式,将二丁和连翘两种药渣按照5种不同的比例进行堆肥处理,通过分析堆肥过程中温度、pH、C/N和发芽指数等指标的变化规律,对堆肥腐熟度进行评价。结果表明:在试验处理条件下及堆肥周期内,单一药渣堆肥的两组处理未能完全腐熟,混合药渣堆肥的3组处理均已达到完全腐熟的标准,说明两种药渣混合后进行堆肥,可以有效促进堆肥的顺利进行,且二丁与连翘比例为2∶1(质量比)时发酵效果最好。3组混合药渣的发酵产物可以作为有机肥或土壤改良剂施用,也可以与化肥配合,制备成有机/无机配方肥。     

二丁与连翘药渣联合堆肥腐熟度评价

为了对不同比例的二丁与连翘药渣堆肥腐熟度进行评价,采用条垛式好氧堆肥方式,将二丁和连翘两种药渣按照5种不同的比例进行堆肥处理,通过分析堆肥过程中温度、pH、C/N和发芽指数等指标的变化规律,对堆肥腐熟度进行评价。结果表明:在试验处理条件下及堆肥周期内,单一药渣堆肥的两组处理未能完全腐熟,混合药渣堆肥的3组处理均已达到完全腐熟的标准,说明两种药渣混合后进行堆肥,可以有效促进堆肥的顺利进行,且二丁与连翘比例为2∶1(质量比)时发酵效果最好。3组混合药渣的发酵产物可以作为有机肥或土壤改良剂施用,也可以与化肥配合,制备成有机/无机配方肥。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.