Fenton氧化/混凝沉淀协同处理腈纶聚合废水

采用Fenton法处理湿法腈纶聚合废水,考察了H2O2投加量、Fe2+投加量、p H和反应时间等因素对氧化和混凝作用去除废水污染物的影响,并分析了废水可生化性和特征污染物的变化。结果表明,Fenton法可以有效去除废水中有机污染物,在初始p H为3.0,Fe2+投加量为15.0 mmol/L,H2O2投加量为90.0 mmol/L的条件下,反应120 min后废水COD去除率可以达到56.8%,其中氧化和混凝作用对应的去除率分别为43.3%和13.5%;处理后废水的BOD5/COD由0.24升高至0.43;处理后废水中丙烯腈以及其他多数有机污染物能被有效去除。     

强化混凝-光电氧化组合工艺深度处理垃圾渗滤液膜滤浓缩液

采用强化混凝-光电氧化组合工艺对北京某垃圾填埋场垃圾渗滤液膜滤浓缩液进行处理。探讨了不同混凝剂投加量、电流密度和反应时间对COD去除率的影响,并考察了溶解性有机物的分子量和结构在本工艺中的变化。结果表明:同时投加Ca(OH)2、Fe2(SO4)3和PAM混凝后,COD去除率为28.00%,含量由4 700 mg/L降低到3 384 mg/L;同时投加KMnO4、Fe2(SO4)3和PAM进行二次混凝,COD去除率为60.20%,含量为1 870 mg/L;混凝后水样在电流密度为400A/m2,经3 h光电氧化后,COD去除率为86.20%,含量为650 mg/L。本工艺将垃圾渗滤液膜滤浓缩液中部分大分子量有机物降解为小分子量有机物;光电氧化后,有机物结构被迅速破坏。     

异相Fenton试剂催化氧化-混凝沉淀深度处理焦化废水

针对焦化废水二级生化处理出水COD、色度和浊度无法达标的问题,实验研究了异相Fenton试剂催化氧化法和混凝沉淀法以及二者联合深度处理焦化废水的效果,分别探讨了H2O2、FeOOH投加量、初始pH,混凝剂投加量及种类对COD去除的影响,确定了最佳运行条件,采用GC-MS分析了联合工艺对废水中有机物的去除规律。异相Fenton试剂催化氧化静态实验研究表明,当H2O2(10%)投加量为2 mL/300 mL,FeOOH投加量为3 g/L,初始pH为4~6之间,处理效果最佳;混凝沉淀实验中最佳的混凝剂为聚丙烯酰胺阳离子,最佳投加量为8 mg/L。异相Fenton试剂催化氧化-混凝沉淀联合工艺深度处理焦化废水,出水COD基本在90 mg/L左右,浊度为0.8NTU左右,色度为40度以下,满足国家污水综合排放二级标准(GB8978-1996)。GC-MS分析显示,联合工艺能有效减少废水中有机物的种类和浓度,并将废水中长链大分子化合物和杂环化合物分解为短链的小分子化合物,构成联合工艺出水COD的主要是小分子有机物,尤其是卤代烷烃含量较高。     

铁碳微电解-混凝对印染废水二级生化出水的深度处理

针对印染废水二级生化出水水质难降解且难以达标的现状,研究在不调节p H的前提下,采用铁碳微电解混凝工艺进行处理研究。通过单因素实验确定最优条件范围,建立响应面(response surface methods,RSM)分析实验,确定铁碳微电解的最佳工艺条件为:Fe的投量为72.1 g/L、m(C)∶m(Fe)为2.98∶1、水力停留时间(HRT)为2.6 h。最佳混凝条件为:Al2(SO4)3投量为100 mg/L、混凝沉淀时间为30 min。实验结果表明,在上述最优工艺条件下对该废水进行深度处理,对COD的去除率能达到50%以上,出水COD低至46.1 mg/L,达到提标后的《纺织染整工业水污染物排放标准》新标准(COD≤60 mg/L),其药剂处理成本为每吨印染废水0.355元左右,该法技术可行、经济合理。     

不同铝系混凝剂处理印染废水

印染废水具有色度大、有机物含量高、水质变化大等特点,处理难度较大。对比了不同种类的混凝剂对印染废水的处理效果,结果表明,随着混凝剂投加量的增加,SS,色度和COD的去除率逐渐增大,当混凝剂的投加量达到80 mg/L时,4种混凝剂的混凝效果达到最优。Al_(13)在最优投加量下SS的去除率达到92.47%,色度去除率达到88.49%,COD的去除率达到80.47%。不同p H值条件下的混凝实验结果表明,随着p H值的升高,混凝效果逐渐提高,在p H值处于6.0~9.0的范围内均具有良好的混凝效果。在沉降的初始阶段,随着沉降时间的延长,4种混凝剂的混凝效果逐渐提高;当沉降时间超过10 min后,混凝效果没有明显的提高。Al_(13)形成絮体的沉降速度最快,11 min左右可以完成沉降,其他3种混凝剂需要在14 min左右完成沉降。     

响应面法优化Fenton法预处理腈纶废水

为得到Fenton法预处理腈纶废水的最优条件参数,以初始pH、H_2O_2投加量、Fe~(2+)投加量、反应时间为考察因素,废水COD去除率为评价指标,在单因素实验基础上,通过Box-Behnken方案构建与拟合响应面模型,分析4个独立因素及各因素之间的交互作用对COD去除效果的影响。确定了最佳Fenton法预处理工艺:初始pH为3.0,H_2O_2投加量为5.0mL/L,Fe~(2+)投加量为4.9g/L,反应时间为150min时。此时,COD去除率预测结果为44.08%,实际运行结果为43.89%,表明该模型可靠。考察了无机离子对Fenton法预处理的影响,并研究预处理前后腈纶废水可生化性的变化。结果表明,SO~(2-)_4对腈纶废水的降解无明显影响,Fenton法预处理显著改善了腈纶废水可生化性。通过对比Fenton法预处理前后腈纶废水的傅立叶变换红外光谱(FTIR)可以得出,Fenton法预处理有效去除了腈纶废水中难降解有机物。     

强化混凝工艺深度处理给水厂排泥废水

水厂废水的综合处理与回用是我国供水行业的新趋势和节水目标所在,采用强化混凝技术进行水厂排泥废水的深度处理。通过混凝剂筛选实验和有机物表征确定最佳混凝剂为高效聚合铝(HPAC),适宜投加量为650 mg/L。当混凝剂HPAC投加量为650 mg/L时,对COD、TOC、浊度和色度的去除率分别为82.5%、89.8%、95%和92.5%,相应的出水值分别为58 mg/L、8.46 mg/L、2.35 NTU、13度,COD满足《污水综合排放标准》(GB 8978-1996)的要求(COD≤100 mg/L),同时实验结果显示聚合氯化铝(PAC)、HPAC、三氯化铁(FeCl3)主要去除分子量处于>1 300 Da范围的有机物,对分子量处于744～1 300 Da之间的有机物去除有限。     

可用于去除高盐废水中有机污染物的混凝-Fenton氧化联合工艺

以某环氧树脂生产厂产生的高盐有机废水为对象,对比研究了Fenton、Fenton-混凝、混凝-Fenton等工艺去除废水中有机污染物的效能。考察了Fenton反应中Fe2+、H2O_2投加比、初始pH、反应时间以及混凝反应中混凝剂种类、投加量等参数对处理效果的影响。结果表明:Fenton工艺的最佳条件为亚铁和过氧化氢投加比1∶20,投加量分别为25 mmol·L~(-1)和500 mmol·L~(-1),初始pH 3,反应时间120 min,TOC去除率为62.50%;混凝工艺选择Fe SO_4混凝剂,投加量为300 mg·L~(-1),TOC去除率为23.78%;废水经过Fenton-无混凝剂混凝、Fenton-混凝剂混凝、混凝-一级Fenton氧化和混凝-二级Fenton氧化工艺处理,TOC去除率分别为68.32%、71.51%、80.69%和89.27%。     

Fenton氧化-序批式膜生物反应器耦合处理干法腈纶废水

采用Fenton氧化-序批式膜生物反应器(SBMBR)组合工艺处理干法腈纶废水。结果表明,在废水初始pH值为3.0,H2O2投加量为90.0 mmol/L,Fe2+投加量为20.0 mmol/L,反应时间为2.0 h的条件下,Fenton氧化预处理对腈纶生产废水的COD去除率达到47.0%以上,COD由1 091 mg/L降至560 mg/L,废水的BOD5/COD由0.32升至0.69,废水的可生化性得到显著提高。Fenton处理出水与丙烯腈废水等比例混合后,采用SBMBR进行生化处理,在水力停留时间为24 h,90 min缺氧/150 min好氧交替运行的条件下,COD、NH4+-N和TN的平均去除率分别为71.7%、97.2%和47.4%,碳源不足是限制TN去除效果的主要影响因素。在无外加碳源的条件下,组合工艺处理后出水COD和NH4+-N浓度分别为117 mg/L和1.7 mg/L,出水水质可以稳定达到国家一级排放标准(GB8978-1996)。     

玉米深加工废水的混凝实验

在室温条件下,分别选用聚合氯化铝(PAC)、聚合氯化铝铁(PAFC)及三氯化铁(FeCl3)对玉米深加工废水进行混凝实验。综合考虑各种混凝剂对磷、COD以及SS的去除效果,最终选取PAC作为混凝剂。采用PAC和聚丙烯酰胺(PAM)作为复合混凝剂,对其去除效果做进一步研究,并确定了最佳投加量及pH值。实验结果表明,在PAC投加量25mg/L,PAM投加量0.5 mg/L,pH为8条件下,混凝效果最佳。磷、COD、SS去除率可分别达到90.1%、53.3%和88.2%,对应的出水质量浓度分别为0.41、26.8和2 mg/L。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.