Formation and destruction of PCDD/F inside a grate furnace

Formation and destruction of polychlorinated dibenzo-p-dioxins and dibenzofurans PCDD/F during the combustion process was investigated experimentally in a pilot plant. All important process steps like the burnout of the fuel bed on the grate, the burnout of the flue gas inside the combustion chamber, the heat recovery in a boiler as well as influences of the fuel composition are described in detail.

High concentrations especially of PCDF are formed during the burnout of the fuel bed. The formation reaction is mainly influenced by the fuel composition and the burnout characteristic of the fuel bed. Fuels with low chlorine and low metal content (Cu) result only in negligible concentrations of PCDD/F.

Under stable combustion conditions characterized by an excellent flue gas burnout PCDD/F will almost be completely destroyed already inside the combustion chamber. “Cold strands” of unburned flue gas (high CO concentrations) caused by disturbed combustion conditions will result in high concentrations of PCDD and especially of PCDF in the raw gas.

A second place of PCDD/F formation is the well-known boiler section. Here fly ash deposits containing residual carbon (mainly soot particles) are the source for the formation reaction. Under stationary effective combustion conditions, they are dominant for PCDD/F concentrations in the raw gas over a very long period of time.

Stationary efficient flue gas burnout (especially soot) together with effective boiler cleaning will guaranty low concentrations of PCDD/F in the flue gas in front of the flue gas cleaning system.     

The role of humic substances in chromium sorption onto natural organic matter (peat)

To elucidate mechanisms of Cr³⁺ sorption onto the unaltered solid natural organic matter, the comparative studies of this ion binding from a solution at pH 4.0 onto three selected particle size fractions: 2000–1000 μm, 630–200 μm and 63–20 μm of markedly different HS content and structure, separated by a wet sieving from an overall sample of peat (Brushwood Peat Humus) were carried out. Comparable patterns of COOH groups and CEC_t confirmed that for cation exchange capacity were responsible mainly cations connected with COO⁻ functional groups. It was though found that aliphatic acids in the solid state did not take part in Cr³⁺ binding, thus the finest studied fraction 63–20 μm of the highest contents of functional groups showed the lowest sorption capacity for Cr³⁺, while similar patterns of sorbed Cr³⁺, soluble HS content and base CEC₀ indicated that these parameters were directly interrelated. The base ion exchange processes determined by CEC₀ (with Ca²⁺ as a predominant exchangeable cation) appeared to be not the major mechanisms responsible for Cr³⁺ sorption. For this metal, strong binding to insoluble large molecular weight organic pool two- to threefold prevailed over the ion exchange processes. Very low acid desorption indicated generally low mobility of Cr³⁺-organic compounds.     

Characterization of carbonaceous combustion residues: II. Nonpolar organic compounds

Aromatic and aliphatic fractions of black carbon (BC) solvent extracts were examined by gas chromatography/mass spectrometry to determine how differences in broad chemical and physical features are correlated with the load, composition, "extractability" and bioavailability of organic compounds. Diesel soot, urban dust and chimney soot had concentrations of n-alkanes >20 microg/g and of carcinogenic polycyclic aromatic hydrocarbons (PAHs)>8 microg/g. These high levels of solvent-extractable compounds were interpreted as resulting from combustion at temperatures below optimum values for BC formation. PAH concentrations normalized to the amount of soot carbon in chimney soot were close to values for diesel soot. However, the high proportion of polar amorphous organic matter in chimney soot suggests a higher bioavailability for associated PAHs. Carbon black, vegetation fire residues, and straw and wood charcoals had only residual concentrations of n-alkanes (<9 microg/g) and PAHs (<0.2 microg/g). PAH distributions were mostly unspecific, while the overall signature of the aliphatic fraction varied with BC origin. Molecular markers among plant-derived BC included steroid and sesquiterpenoid hydrocarbons. Molecular fingerprints suggest that compounds associated with fossil BC might be more refractory than those associated with plant-derived BC.     

Characterisation of particulate matter and gaseous emissions from a large ship diesel engine

Composition of exhaust from a ship diesel engine using heavy fuel oil (HFO) was investigated onboard a large cargo vessel. The emitted particulate matter (PM) properties related to environmental and health impacts were investigated along with composition of the gas-phase emissions. Mass, size distribution, chemical composition and microphysical structure of the PM were investigated. The emission factor for PM was 5.3 g (kg fuel)^?1. The mass size distribution showed a bimodal shape with two maxima: one in the accumulation mode with mean particle diameter D_P around 0.5 μm and one in the coarse mode at D_P around 7 μm. The PM composition was dominated by organic carbon (OC), ash and sulphate while the elemental carbon (EC) composed only a few percent of the total PM. Increase of the PM in exhaust upon cooling was associated with increase of OC and sulphate. Laser analysis of the adsorbed phase in the cooled exhaust showed presence of a rich mixture of polycyclic aromatic hydrocarbon (PAH) species with molecular mass 178–300 amu while PM collected in the hot exhaust showed only four PAH masses.Microstructure and elemental analysis of ship combustion residuals indicate three distinct morphological structures with different chemical composition: soot aggregates, significantly metal polluted; char particles, clean or containing minerals; mineral and/or ash particles. Additionally, organic carbon particles of unburned fuel or/and lubricating oil origin were observed. Hazardous constituents from the combustion of heavy fuel oil such as transitional and alkali earth metals (V, Ni, Ca, Fe) were observed in the PM samples.Measurements of gaseous composition in the exhaust of this particular ship showed emission factors that are on the low side of the interval of global emission factors published in literature for NO_x, hydrocarbons (HC) and CO.     

Utilization and degradation of imazaquin by a naturally occurring isolate of Arthrobacter crystallopoietes

A species of bacteria that is capable of utilizing imazaquin as the sole carbon source was isolated from soil with repeated imazaquin applications, and was identified as Arthrobacter crystallopoietes (designated as strain “WWX-1”). This isolate degrades imazaquin as high as 200 μg ml⁻¹, and the estimated dissipation half-lives increased from 1.51 d for the treatment at 50 μg ml⁻¹ to 4.75 d for 200 μg ml⁻¹. Optimal growth of WWX-1 in mineral salt medium with 50 μg ml⁻¹ imazaquin was obtained at 35 °C and a pH of 5.0. Growth of WWX-1 was also observed in mineral salt medium with the addition of other imidazolinone herbicides such as imazethapyr and imazapyr, but not with different classes of herbicides such as metsulfuron-methyl. Two imazaquin metabolites were detected, and spectral analysis with HPLC–MS, ¹H NMR, and IR revealed one metabolite with a molecular weight (MW) of 199 as quinoline-2,3-dicarboxylic anhydride. We propose that A. crystallopoietes (WWX-1) could serve as an efficient biodegradation system for remediation of water and soils that are heavily contaminated with imazaquin or other structurally similar chemicals.     

Using Radiocarbon to Apportion Sources of Polycyclic Aromatic Hydrocarbons in Household Soot

To determine whether polycyclic aromatic hydrocarbons (PAHs) in household soot were derived from the combustion of scrap wood or creosote that was impregnated in the wood (or some combination of both), the molecular composition and radiocarbon ( 14 C) content of the total carbon and several PAHs in the soot was investigated. The 5730-year half-life of 14 C makes it an ideal marker for identifying creosote-derived PAHs ( 14 C-free) versus those derived from the combustion of wood (contemporary 14 C). The 14 C abundance of phenanthrene, fluoranthene, pyrene, and retene was determined by accelerator mass spectrometry after solvent extraction and purification by preparative capillary gas chromatography. The molecular analysis (presence of retene and 1,7-dimethylphenanthrene) and bulk 14 C content (contemporary) of the soot indicated that wood combustion was a strong source of carbon to the soot. The 14 C of retene in two soot samples was also contemporary, indicating that it was derived from the combustion of the scrap wood. These results are consistent with previous work that has suggested that retene is an excellent marker of wood combustion. However, the 14 C content of phenanthrene, fluoranthene, and pyrene in one soot sample was much lower and revealed that these compounds had a mixed creosote and wood source. Using an isotopic mass balance approach, we estimate that 40 to 70% of phenanthrene, fluoranthene, and pyrene were derived from the combustion of the scrap wood. The results of this study show that molecular marker and bulk 14 C analysis can be potentially misleading in apportioning sources of every PAH, and that molecular-level 14 C analysis of PAHs can be a powerful tool for environmental forensics.     

A morphological investigation of soot produced by the detonation of munitions

The morphology of three different detonation soot samples along with other common soot materials such as carbon black, diesel soot and chimney soot was studied by elemental and proximate analysis, X-ray diffraction and electron microscopy. The goal of this study was to better define the morphology of the detonation soot in order to better assess the interactions of this type of soot with explosive residues. The detonation soot samples were obtained by the detonation of artillery 155mm projectiles filled with either pure TNT (2,4,6-trinitrotoluene) or composition B, a military explosive based on a mixture of TNT and RDX (trimethylentrinitramine). The carbon content of the soot samples varied considerably depending on the feedstock composition. Detonation soot contains less carbon and more nitrogen than the other carbonaceous samples studied, due to the molecular structure of the energetic materials detonated such as TNT and RDX. The ash concentration was higher for detonation soot samples due to the high metal content coming from the projectiles shell and to the soil contamination which occurred during the detonation. By X-ray diffraction, diamond and graphite were found to be the major crystalline carbon forms in the detonation soot. Two electron microscopy techniques were used in this study to visualise the primary particles and to try to explain the formation mechanism of detonation soot samples.     

Chemical and Biological Characterization of Products of Incomplete Combustion from the Simulated Field Burning of Agricultural Plastic

Chemical and biological analyses were performed to characterize products of Incomplete combustion emitted during the simulated open field burning of agricultural plastic. A small utility shed equipped with an air delivery system was used to simulate pile burning and forced-air-curtain incineration of a nonhalogenated agricultural plastic that reportedly consisted of polyethylene and carbon black. Emissions were analyzed for combustion gases; volatile, semi-volatile, and particulate organics; and toxic and mutagenlc properties. Emission samples, as well as samples of the used (possibly pesticide-contaminated) plastic, were analyzed for the presence of several pesticides to which the plastic may have been exposed. Although a variety of alkanes, alkenes, and aromatic and polycyclic aromatic hydrocarbon (PAH) compounds were identified in the volatile, seml-volatlle, and particulate fractions of these emissions, a substantial fraction of higher molecular weight organic material was not identified. No pesticides were Identified in either combustion emission samples or dlchloromethane washes of the used plastic. When mutagenlcity was evaluated by exposing Salmonella bacteria (Ames assay) to whole vapor and vapor/partlculate emissions, no toxic or mutagenlc effects were observed. However, organic extracts of the particulate samples were moderately mutagenlc. This mutagenlcity compares approximately to that measured from residential wood heating on a revertant per unit heat release basis. Compared to pile burning, forced air slightly decreased the time necessary to burn a charge of plastic. There was not a substantial difference, however, in the variety or concentrations of organic compounds Identified In samples from these two burn conditions. This study highlights the benefits of a combined chemical/biological approach to the characterization of complex, multi-component combustion emissions. These results may not reflect those of other types of plastic that may be used for agricultural purposes, especially those containing halogens.     

Comparison of various sampling methods for PCDDs and PCDFs in stack gas

There have been discussions about how complete PCDDs and PCDFs are sampled from stack gas of waste combustion plants by various sampling methods. In Germany, at present, a sampling method is used, which was first proposed by Nottrodt et al.¹, consisting of a filter device, condenser, and an absorption train. Since this sampling procedure complicates sampling and analysis, we compared this “standard procedure” with a “dilution method”, where only a filter, impregnated with paraffin, is used as trapping device, and also tested the effectiveness of XAD-2 as an adsorption trap.

As standard procedure the standard train was always used in parallel to other sampling methods. The results of four parallel sampling periods confirmed, that comparable results are obtained, when parallel sampling is carried out with the standard train.

The result of our investigation can be summarized as follows: The total emission of PCDDs and PCDFs determined by different sampling procedures varies only insignificantly. This means that sampling and analysis for PCDDs and PCDFs in stack gas could be simplified considerably.     

The use of bioluminescent biotests for study of natural and laboratory aquatic ecosystems

A set of bioluminescent tests was developed to monitor water quality in natural and laboratory ecosystems. It consisted of four bioluminescent systems: luminous bacteria, coupled enzyme system NADH:FMN-oxidoreductase-luciferase and triplet enzyme systems with alcohol dehydrogenase and trypsin. The set of biotests was applied for a small forest pond (Siberia, Russia), laboratory microecosystems polluted with benzoquinone and a batch culture of blue-green algae. Thereby effects of natural water compared to those of models of heavy pollution and “bloom” of blue-greens on the bioluminescent tests were revealed. The set of biotests was not affected by a natural seasonal variability of water quality in the unpolluted pond, but responded to the heavy pollution and the “bloom” of blue-greens. The set of biotests could be recommended as the alarm test to control the acute toxicity of natural water bodies.     

PAH and soot emissions from burning components of medical waste: examination/surgical gloves and cotton pads

This is a laboratory investigation on the emissions from batch combustion of representative infectious ("red bag") medical waste components, such as medical examination latex gloves and sterile cotton pads. Plastics and cloth account for the majority of the red bag wastes by mass and, certainly, by volume. An electrically heated, horizontal muffle furnace was used for batch combustion of small quantities of shredded fuels (0.5-1.5 g) at a gas temperature of approximately 1000 degrees C. The residence time of the post-combustion gases in the furnace was approximately 1 s. At the exit of the furnace, the following emissions were measured: CO, CO2, NOx, particulates and polynuclear aromatic compounds (PACs). The first three gaseous emissions were measured with continuous gas analyzers. Soot and PAC emissions were simultaneously measured by passing the furnace effluent through a filter (to collect condensed-phase PACs) and a bed of XAD-4 adsorbent (to capture gaseous-phase PACs). Analysis involved soxhlet extraction, followed by gas chromatography-mass spectrometry (GC-MS). Results were contrasted with previously measured emissions from batch combustion of pulverized coal and tire-derived fuel (TDF) under similar conditions. Results showed that the particulate soot) and cumulative PAC emissions from batch combustion of latex gloves were more than an order of magnitude higher than those from cotton pads. The following values are indicative of the relative trends (but not necessarily absolute values) in emission yields: 26% of the mass of the latex was converted to soot, 11% of which was condensed PAC. Only 2% of the mass of cotton pads was converted to soot, and only 3% of the weight of that soot was condensed PAC. The PAC yields from latex were comparable to those from TDF. The PAC yields from cotton were higher than those from coal. A notable exception to this trend was that the three-ring gas-phase PAC yields from cotton were more significant than those from latex. Emission yields of CO and CO2 from batch combustion of cotton were, respectively, comparable and higher than those from latex, despite the fact that the carbon content of cotton was half that of latex. This is indicative of the more effective combustion of cotton. Nearly all of the mass of carbon of cotton gasified to CO and CO2 while only small fractions of the carbon in latex were converted to CO2 and CO (20% and 10%, respectively). Yields of NOx from batch combustions of latex and cotton accounted for 15% and 12%, respectively, of the mass of fuel nitrogen indicating that more fuel nitrogen was converted to NOx in the former case, possibly due to higher flame temperatures. No SO2 emissions were detected, indicating that during the fuel-rich combustion of latex, its sulfur content was converted to other compounds (such as H2S) or remained in the soot.     

Photodegradation of malachite green under natural sunlight irradiation: kinetic and toxicity of the transformation products

This article describes the photolytic degradation of malachite green (MG), a cationic triphenylmethane dye used worldwide as a fungicide and antiseptic in the aquaculture industry. Photolysis experiments were performed by direct exposure of a solution of MG in water to natural sunlight. The main transformation products (TPs) generated during the process were identified by liquid chromatography time-of-flight mass spectrometry (LC–TOF-MS) and gas chromatography mass spectrometry (GC–MS). The 28 TPs identified with this strategy indicate that MG undergoes three main reactions, N-demethylation, hydroxylation and cleavage of the conjugated structure forming benzophenone derivatives. These processes involve hydroxyl radical attack on the phenyl ring, the N,N-dimethylamine group and the central carbon atom. The Vibrio fischeri acute toxicity test showed that the solution remains toxic after MG has completely disappeared. This toxicity could be assigned, at least in part, to the formation of 4-(dimethylamine)benzophenone, which has an EC_50,30 min of 0.061 mg l⁻¹, and is considered “very toxic to aquatic organisms” by current EU legislation.     

Formation of PCDDs and PCDFs by the chlorination of water

Two samples of tab water and double distilled water were chlorinated using chlorine gas. A series of PCDFs could be identified from these experiments, however no PCDDs could be found. The two water samples gave very similar isomeric patterns ( . . tetra-CDFs), however the congener profile (Cl₄ --- Cl₈) was different. These experiments indicate that all products formed by chlorination reactions are potentially contaminated by PCDFs by a specific “chlorine pattern”.     

Investigation on organic pollutants from a domestic heating system using various solid biofuels

Various herbaceous biofuels (straw, whole plant cereals and set aside hay) and spruce wood were tested for their potential to form PCDD/F, PCPh, PCBz and PAH during combustion. The trials were conducted in an automatically charged multi-fuel furnace for domestic applications (50 kWth). Both, flue gas and the different ash fractions were analysed. CO-emission results show, that combustion conditions were relatively uniform (mean CO-level: 200 mg/m3 at 13% O2 in flue gas). Likewise, the TOC- and PAH-emissions in the fuel gas remained constantly on a relatively low level. However, for the PCDD/F, PCPh and PCBz increased emissions were detected when herbacious fuels were applied. This may be attributed to their higher chlorine concentration and the high ash content, which is responsible for increased dust emissions during combustion. Similar observations were also found for the PCDD/F-concentrations in the ashes. Combustion chamber ashes usually showed a drastically reduced contamination with highly toxical compounds, compared to the ash fraction from the heat exchanger ash or to chimney soot.     

A review of biomarker compounds as source indicators and tracers for air pollution

An overview of the application of organic geochemistry to the analysis of organic matter on aerosol particles is presented here. This organic matter is analyzed as solvent extractable bitumen/ lipids by gas chromatography-mass spectrometry. The organic geochemical approach assesses the origin, the environmental history and the nature of secondary products of organic matter by using the data derived from specific molecular analyses. Evaluations of production and fluxes, with cross-correlations can thus be made by the application of the same separation and analytical procedures to samples from point source emissions and the ambient atmosphere. This will be illustrated here with typical examples from the ambient atmosphere (aerosol particles) and from emissions of biomass burning (smoke). Organic matter in aerosols is derived from two major sources and is admixed depending on the geographic relief of the air shed. These sources are biogenic detritus (e.g., plant wax, microbes, etc.) and anthropogenic particle emissions (e.g., oils, soot, synthetics, etc.). Both biogenic detritus and some of the anthropogenic particle emissions contain organic materials which have unique and distinguishable compound distribution patterns (C₁₄-C₄₀). Microbial and vascular plant lipids are the dominant biogenic residues and petroleum hydrocarbons, with lesser amounts of the pyrogenic polynuclear aromatic hydrocarbons (PAH) and synthetics (e.g., chlorinated compounds), are the major anthropogenic residues. Biomass combustion is another important primary source of particles injected into the global atmosphere. It contributes many trace substances which are reactants in atmospheric chemistry and soot paniculate matter with adsorbed biomarker compounds, most of which are unknown chemical structures. The injection of natural product organic compounds into smoke occurs primarily by direct volatilization/steam stripping and by thermal alteration based on combustion temperature. Although the molecular composition of organic matter in smoke particles is highly variable, the molecular tracers are generally still source specific. Retene has been utilized as a tracer for conifer smoke in urban aerosols, but is not always detectable. Dehydroabietic acid is generally more concentrated in the atmosphere from the same emission sources. Degradation products from biopolymers (e.g., levoglucosan from cellulose) are also excellent tracers. An overview of the biomarker compositions of biomass smoke types is presented here. Defining additional tracers of thermally-altered and directly-emitted natural products in smoke aids the assessment of the organic matter type and input from biomass combustion to aerosols. The precursor to product approach of compound characterization by organic geochemistry can be applied successfully to provide tracers for studying the chemistry and dispersion of ambient aerosols and smoke plumes. Presented at the 6th FECS Conference on Chemistry and the Environment, Atmospheric Chemistry and Air Pollution, August 26–28, 1998, Copenhagen.     

Evaluation of the thermal/optical reflectance method for discrimination between char- and soot-EC

Many optical, thermal and chemical methods exist for the measurement of elemental carbon (EC) but are unable or neglect to differentiate between the different forms of EC such as char- or soot-EC. The thermal/optical reflectance (TOR) method applies different temperatures for measuring EC and organic carbon (OC) contents through programmed, progressive heating in a controlled atmosphere, making available eight separate carbon fractions - four OC, one pyrolyzed organic carbon, and three EC. These fractions were defined by temperature protocol, oxidation atmosphere, and laser-light reflectance/transmittance. Stepwise thermal evolutional oxidation of the TOR method makes it possible to distinguish char- from soot-EC. In this study, different EC reference materials, including char and soot, were used for testing it. The thermograms of EC reference materials showed that activation energy is lower for char- than soot-EC. Low-temperature EC1 (550 degrees C in a 98% He/2% O2 atmosphere) is more abundant for char samples. Diesel and n-hexane soot samples exhibit similar EC2 (700 degrees C in a 98% He/2% O2 atmosphere) peaks, while carbon black samples peaks at both EC2 and EC3 (800 degrees C in a 98% He/2% O2 atmosphere). These results supported the use of the TOR method to discriminate between char- and soot-EC.     

Azo-dyes photocatalytic degradation in aqueous suspension of TiO2 under solar irradiation

The photodegradation of two common and very stable azo-dyes, i.e. methyl-orange (C₁₄H₁₄N₃SO₃Na) and orange II (C₁₆H₁₁N₂SO₄Na), is reported. The photocatalytic oxidation was carried out in aqueous suspensions of polycrystalline TiO₂ irradiated by sunlight. Compound parabolic collectors, installed at the “Plataforma Solar de Almería” (PSA, Spain) were used as the photoreactors and two identical reacting systems allowed to perform photoreactivity runs for the two dyes at the same time and under the same irradiation conditions. The disappearance of colour and substrates together with the abatement of total organic carbon content was monitored. The main sulfonate-containing intermediates were found to be in lower number in respect to those obtained under artificial irradiation. In particular there were no more evidence of the presence of hydroxylated transients. The dependence of dye photooxidation rate on: (i) substrate concentration; (ii) catalyst amount; and (iii) initial pH was investigated. The influence of the presence of strong oxidant species (H₂O₂, S₂O₈²⁻) and some ions (Cl⁻, SO₄²⁻) on the process was also studied.     

Carbon nanotube-like materials in the exhaust from a diesel engine using gas oil/ethanol mixing fuel with catalysts and sulfur

Particulate matter from a diesel engine, including soot and carbon nanomaterials, was collected on a sampling holder and the structure of the materials was studied by transmission electron microscopy (TEM) and scanning electron microscopy (SEM). As a result of employing gas oil/ethanol mixing fuel with sulfur and ferrocene/molybdenum as catalyst sources, formation of carbon nanotubes (CNT)-like materials in addition to soot was observed in the exhaust gas from a diesel engine. It was revealed that CNT-like materials were included among soot in our system only when the following three conditions were satisfied simultaneously: high ethanol fraction in fuel, high sulfur loading, and presence of catalyst sources in fuel. This study confirmed that if at least one of these three conditions was not satisfied, CNT-like materials were not observed in the exhaust from a diesel engine. These experimental results shown in this work provide insights into understanding CNT-like material formation mechanism in a diesel engine.

Implications: Recent papers reported that carbon nanotube-like materials were included in the exhaust gas from engines, but conditions for carbon nanotube-like material formation have not been well studied. This work provides the required conditions for carbon nanotube-like material growth in a diesel engine, and this will be helpful for understanding the carbon nanotube-like material formation mechanism and taking countermeasures to preventing carbon nanotube-like material formation in a diesel engine.     

Photomineralization of n-alkanoic acids in aqueous solution by photocatalytic membranes. Influence of trialkyl vanadates as catalytic promoters of immobilized titanium dioxide

The Ti0₂-mediated photomineralization of 8–1000 ppm of methanoic acid, of 6–100 ppm of ethanoic acid, of 6–180 ppm of propanoic acid, and of 6–90 ppm of n-decanoic acid in aqueous solutions was studied at 296± 2 K or 308 ± 2 K, with low and high pressure mercury arc lamps (radiant power in the absorption range 8 and 145 W respectively), using PHOTOPERM® CPP/313 membranes containing immobilized 30±3 wt.% Ti0₂, and, in parallel runs, 7 wt.% of a synergic mixture of tri(t-butyl)- and tri-(i-propyl) vanadate(V) as photocatalytic promoter. Stoichiometric H₂0₂ was used or, in some of the runs, 0₃, at saturation, as oxygen suppliers. Disappearance of total organic carbon (TOC) was followed as a function of time. To fit kinetic curves up to complete photomineralization, a kinetic model was employed, already used successfully in previous studies, which considers appearance and disappearance of all intermediates, as if they were represented by a hypothetical single molecule, mediating all of them. The photocatalytic activity of trialkyl vanadates was evaluated from quantum yields at “infinite” concentration, with respect to the maximum allowable efficiencies. When using O₃, a dark catalysis effect clearly appeared towards intermediate species produced during the photocatalysed degradation.     

Soot Control During the Combustion of Polystyrene

This paper describes an experimental study on the control of soot formation during the combustion of polystyrene (PS). A stable, twodimensional flame generated by using a Wolfhard-Parker type diffusion flame burner was used to simulate practical combustion situations. The combustion characteristics, effects of operating conditions on soot formation, and the effectiveness of various metallic additives as soot suppressants were investigated. It was found that soot yield could not be significantly reduced by controlling the oxidizer (air) flow rate. Increasing the O₂ mole fraction of the oxidlzer increased soot yield under typical operating conditions. However, soot yield could be greatly reduced by adding small amounts of air into the pyrolysis zone of the flame. The additional air would probably increase the combustion reaction rate while decreasing the soot precursor formation rate, thereby causing the observed effect. It was thus suggested that effective soot control could be accomplished by improving mixing between air and the PS devolatilizatlon products In practical combustion situations. The metallic additives tested in this study were the salts of Na, K, Ca, and Ba. Among these salts, Ca was the least effective in reducing soot, and K and Na were nearly equally effective. Ba was much more effective than all the others, and Its effectiveness was strongly dependent on its addition rate.