SiO3^2-离子的加入对脉冲倒极电解合成PASiC的研究

探索了试验过程中SiO3^2-离子团的加入对脉冲自动倒极电解法合成聚合氯化硅酸铝中Alb含量的影响。通过试验确定了最佳摩尔比。在脉冲倒极周期和电解槽电流一定的情况下，当总铝Al，与SiO3^2-的摩尔比为10：1～20：1时；在此合成条件下制备液中Alb含量超过80％；处理模拟水样最佳投药量为：0．5～5mgAl2O3／L。在制备过程中，极化现象得到了极好的控制，电解槽电压和电流十分稳定。     

SiO23-离子的加入对脉冲倒极电解合成PASiC的研究

探索了试验过程中SiO23-离子团的加入对脉冲自动倒极电解法合成聚合氯化硅酸铝中Alb含量的影响.通过试验确定了最佳摩尔比.在脉冲倒极周期和电解槽电流一定的情况下,当总铝AlT与SiO23-的摩尔比为101～201时;在此合成条件下制备液中Alb含量超过80%;处理模拟水样最佳投药量为0.5～5 mg Al2O3/L.在制备过程中,极化现象得到了极好的控制,电解槽电压和电流十分稳定.     

电絮凝过程中倒极消除极板钝化

针对电絮凝处理污水过程中极板易发生钝化影响电絮凝效果的问题,采用倒极方法消除了极板钝化,并通过SEM和EDS,定性、定量分析不同反应时间段极板的表面形态和元素含量的变化,研究了表面钝化层成分及含量随处理时间的变化趋势。结果表明:电絮凝处理压裂废水中Al阳极钝化层的主要成分是Al_2O_3,阴极钝化层的主要成分是CaCO_3;倒极后的阴极板表面Al_2O_3含量在20 h内由48.94%下降到18.73%,阳极板Al_2O_3含量由11.87%降低到9.28%,这表明倒极能有效消除Al_2O_3氧化膜对极板钝化的影响;对于Ca~(2+)含量较低的压裂废水,倒极使CaCO_3的吸附量控制在0.01%～0.34%,可有效控制极板钝化现象的发生。     

新型高效氧化偶合絮凝剂COF-I的研制及其应用研究

以硫酸铝为主要原料 ,经过化学改性后 ,制得兼具氧化和絮凝为一体的新型、高效水处理药剂COF I ,并设计正交实验找出了药剂最佳组合配方 ,且对微污染水源水、城市污水及印染废水进行了强化处理试验研究。结果表明 ,最佳配方为复合比 1∶1、添加剂含量 1 2 5 %、稳定剂含量 0 3%、氧化成分含量 1 0 % ,在最佳配方和最佳工艺条件下 ,复合药剂COF I对微污染水源水、城市污水及印染废水均具有良好的处理效果     

污泥与底泥烧结陶粒骨料的中试研究

建立了中试研究生产线,工艺流程包括干燥、粉磨、混合上料、成型、烧结和烟气处理等,在中试生产线上,对污泥(包括工业污泥(ISS)和生活污泥(DSS))与底泥烧结制备陶粒骨料的物料配比、烧结温度、添加剂等相关技术参数进行了系统研究。研究发现,ISS中CaO和磷的化合物含量较高,导致骨料的膨胀性能不佳,添加一定量的生活污水污泥(DSS)可改善骨料的膨胀性能。中试研究确定600～800级的陶粒骨料烧结的适宜工艺条件为:配比SS∶DSS∶RS=1∶4∶5～1∶5∶4或DSS∶RS=3∶7～5∶5,烧结温度1 140℃,烧结时间28 min环境安全性研究表明,在陶粒烧结过程中大部分重金属在烧结过程中被固定在陶粒中,重金属浸出率非常低,在使用过程中不会对环境产生危害。     

分子印迹型TiO_2的制备及其对邻苯二甲酸二(2-乙基)己酯的光催化性能

以邻苯二甲酸二(2-乙基)己酯为模板分子、甲基丙烯酸为功能单体和乙二醇二甲基丙烯酸酯为交联剂,在TiO_2表面合成DEHP分子印迹聚合物,制备了分子印迹型TiO_2(MIP-TiO_2),优化了制备工艺条件。利用傅里叶红外光谱(FIIR)和X-射线衍射(XRD)对MIP-TiO_2进行表征,并考察了MIP-TiO_2对DEHP的光催化降解性能。结果表明,MIP-TiO_2的最佳制备工艺条件为模板分子、单体、交联剂和TiO_2的摩尔比为1∶4∶10∶1.875,反应温度为60℃;聚合时间为18 h。MIPTiO_2仍保持了和TiO_2一样的锐钛矿型结构,对DEHP的光催化效果明显高于TiO_2,对浓度为5 mg·L~(-1)的DEHP的光催化降解效率可达88.15%。     

焦炭负载改性纳米TiO2阳光催化降解染料模拟废水的初步研究

以焦炭为载体，Na2SiO3为粘结剂，制备了负载型铁改性纳米TiO3光催化剂，并研究了该催化剂在太阳光照射下降解亚甲基兰染料废水的效果，通过正交和单因素优化试验，探讨了影响染料废水降解效果的主要因素，研究结果表明，影响降解因素的大小次序是：煅烧时间〉铁掺杂量〉Na2SiO3质量百分比〉煅烧温度。本光催化剂制备的最佳制备条件是：以20％的Na2SiO3溶液为粘结剂，掺杂2％的Fe，400℃煅烧温度下煅烧3h。以太阳光为光源，亚甲基兰染料废水的降解率可达到87．1％。     

氧化铝对煤矸石提铝废渣制备水玻璃的影响

以纯石英砂或煤矸石酸浸提铝废渣为原料,采用低温(850℃)纯碱烧结法制备水玻璃,考察了杂质Al2O3含量对原料中SiO2溶出率以及产品水玻璃模数的影响,通过电感耦合等离子发射光谱(ICP)、傅里叶红外光谱仪(FTIR)、X射线衍射仪(XRD)和热重分析(TGA)手段对原料和产物进行了分析和表征.结果表明,与纯石英砂为原料制备水玻璃相比,杂质Al2O3的存在降低了SiO2-Na2O体系的反应温度,但由于Al2O3会与反应体系中的SiO2和Na2O反应生成水不溶性的铝硅酸钠盐,导致实际可溶性SiO2的含量减少,降低了SiO2的溶出率和硅酸钠的模数.通过添加石英砂可控制提铝废渣中的A12O3含量低于5％,使提铝废渣中SiO2的溶出率达到90％以上,制得水玻璃模数达2.15.     

复合絮凝剂APAC中铝形态分布及絮凝性能研究

用慢速滴碱法合成聚合氯化铝的过程中加入酸改性的凹凸棒,制备了新型絮凝剂APAC。采用Al-Ferron逐时络合比色法和烧杯絮凝实验法分别研究了APAC复合絮凝剂中铝的形态分布和絮凝性能。结果表明,Ala随盐基度的升高而逐渐降低;Alb随盐基度的升高而升高;Alc则先随盐基度的升高而升高,达到最大值后,再随盐基度的升高而降低。在相同实验条件下,盐基度愈高,混凝效果愈好,Alb含量愈高,混凝效果并不一定愈好。因此,APAC的质量控制以及追求目标应当是尽量提高Alc的含量,而不是Alb的含量。     

应用于微波处理正丁酸模拟废水的催化剂制备及表征

通过正交实验对镍铁铈(Ni-Fe-Ce)、镍铁钛(Ni-Fe-Ti)、镍铁锆(Ni-Fe-Zr)3组复合催化剂的共沉淀-焙烧法制备工艺进行优化,并对优选出的催化剂进行SEM和XRD表征。结果表明,镍铁锆催化剂是最优催化剂,最佳制备条件为Ni∶Fe(摩尔比)0∶10、Zr∶Fe(摩尔比)4∶1、干燥时间6 h、焙烧温度350℃、焙烧时间6 h、沉淀时间5 h;此条件下制备的Fe-Zr催化剂的催化效能最高,TOC去除率达到75%;Zr的掺和改变了Fe催化剂的物相,进而提高了Fe催化剂的催化活性。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染