侧流化学除磷对AO连续流生物除磷系统的影响

为解决城市污水高效除磷和磷回收的问题,开发厌氧释磷上清液侧流除磷工艺(anaerobic supernatant phosphate strip process,简称ASPS工艺),在侧流比为33%下运行,发现该工艺对生物除磷系统的影响主要表现在以下几个方面:(1)系统磷和有机物的去除性能不受影响,出水可溶性磷和COD浓度分别为(0.53±0.12)mg/L、(42.00±5.69)mg/L;(2)活性污泥分布松散并与大量丝状菌结合成难沉降的絮状结构,沉降性能变差,粒径变小;(3)从系统内微生物能量代谢角度分析知,胞内PHA和糖原含量水平无明显变化;但胞内聚磷颗粒含量减少,厌氧释磷受阻,侧流厌氧释磷浓度从22.17mg/L下降至5.20 mg/L,最终导致侧流部分失去高浓度磷化学沉淀的优势;(4)化学磷回收量占进水磷量比由133.02%下降至31.20%,可实现磷的有效去除和回收利用;(5)对微生物种群变化的影响还有待进一步探究。     

水解酸化-A~2O污泥减量工艺的运行性能研究

生物处理单元采用水解酸化、多级串联接触曝气、连续流的除磷脱氮A2/O工艺,并辅以外排厌氧富磷污水侧流除磷,开发了一个新型的具有强化除磷脱氮功能的污泥减量HA-A/A-MCO工艺。用该工艺处理校园生活污水发现,在SRT60 d、进水COD 316~407 mg/L、NH4+-N30~40 mg/L、TN35~53 mg/L、TP 8~12 mg/L的条件下,出水COD≤18 mg/L、NH4+-N≤2.1 mg/L、TN≤10.3 mg/L、TP≤0.44 mg/L。研究还发现,水解酸化池处理产生的VFA能有效促进生物除磷脱氮,导致厌氧释磷量达57 mg/L,进入化学除磷池的侧流液量仅相当于进水量的13%;系统最主要的脱氮形式是SND和缺氧反硝化,SND脱氮占脱氮总量的50%,缺氧反硝化占26%;HA-A/A-MCO系统有效实现了生物相分离,并利用生物捕食作用获得较低的污泥产率,0.1 g MLSS/g COD。     

污水生物除磷若干影响因素分析

在系统阐述污水生物除磷机理的基础上,深入分析了微生物群体平衡、城市污水水质、环境因子以及工艺运行参数和运行方式等方面对生物除磷效果的影响.分析结果表明:生物除磷系统的溶解氧浓度不宜太高,一般好氧区DO＜2 mg/L,厌氧区DO＜0.2 mg/L;厌氧段存在硝酸盐对生物释磷有负面影响,缺氧段存在一定浓度的硝酸盐有利于生物聚磷;碳源必须充分、易降解;TKN/COD＜0.1的城市污水有利于生物除磷;pH偏碱性可提高生物除磷效率;低温对生物除磷效果影响不明显.     

厌氧-立体循环一体化氧化沟除磷脱氮工艺中影响厌氧释磷的因素研究

本研究考察了厌氧-立体循环一体化氧化沟工艺(AN-IODVC)中厌氧释磷效果及诸影响因素.研究结果表明,AN-IODVC除磷脱氮系统中好氧污泥的VSS/MLSS值比厌氧污泥小,好氧污泥含磷量与厌氧污泥含磷量的差值和TP去除率、厌氧磷释放率及厌氧ORP呈良好的线性相关关系.厌氧磷释放的最佳条件为:污水COD/TP＞55,维持厌氧区ORP低于-400mV.     

厌氧-立体循环一体化氧化沟除磷脱氮工艺中影响厌氧释磷的因素研究

本研究考察了厌氧-立体循环一体化氧化沟工艺（AN-IODVC）中厌氧释磷效果及诸影响因素.研究结果表明,AN-IODVC除磷脱氮系统中好氧污泥的VSS/MLSS值比厌氧污泥小,好氧污泥含磷量与厌氧污泥含磷量的差值和TP去除率、厌氧磷释放率及厌氧ORP呈良好的线性相关关系.厌氧磷释放的最佳条件为：污水COD/TP＞55,维持厌氧区ORP低于-400mV.     

COD对强化生物除磷系统的影响及OUR的变化规律

以实际生活污水为研究对象,在SBR系统中采用厌氧/好氧运行方式,考察强化生物除磷(EBPR)系统中好氧阶段COD浓度对聚磷菌除磷性能的影响以及不同好氧阶段COD浓度下的OUR变化规律.实验分4个阶段进行,分别为不投加外碳源、厌氧结束时投加不同体积的乙酸钠作为外碳源,使COD分别提高50、100和300mg/L.4种工况...     

氧化锌纳米颗粒对污水生物除磷的影响及其机理研究

在序批式反应器中探究了不同浓度氧化锌纳米材料(ZnO NPs)对污水生物强化除磷的影响。结果表明:(1)低质量浓度(1mg/L)ZnO NPs对污水生物除磷影响不明显,而高质量浓度(32mg/L)ZnO NPs能明显降低生物除磷效率(除磷效率仅为55%左右)。(2)高浓度ZnO NPs的存在能抑制厌氧释磷和好氧吸磷。32mg/L ZnO NPs作用下聚磷菌相对丰度仅为21.6%,明显低于空白组,与除磷相关的酶活也明显低于空白组。     

水解酸化-A2O污泥减量工艺的运行性能研究

生物处理单元采用水解酸化、多级串联接触曝气、连续流的除磷脱氮A2／O工艺，并辅以外排厌氧富磷污水侧流除磷，开发了一个新型的具有强化除磷脱氮功能的污泥减量HA—A／A—MCO工艺。用该工艺处理校园生活污水发现，在SRT60d、进水COD316～407mg／L、NH4＋-N30～40mg／L、TN35～53mg／L、TP8—12mg／L的条件下，出水COD≤18mg／L、NH4＋-N≤2．1mg／L、TN≤10．3mg／L、TP≤0．44mg／L。研究还发现，水解酸化池处理产生的VFA能有效促进生物除磷脱氮，导致厌氧释磷量达57mg／L，进入化学除磷池的侧流液量仅相当于进水量的13％；系统最主要的脱氮形式是SND和缺氧反硝化，SND脱氮占脱氮总量的50％，缺氧反硝化占26％；HA-A／A—MCO系统有效实现了生物相分离，并利用生物捕食作用获得较低的污泥产率，0．1gMLSS／gCOD。     

生物倍增工艺同步脱氮除磷强化途径分析

通过对生物倍增工艺处理市政污水的沿程污染物降解规律的考察表明,工艺对有机物的去除效果显著,COD和BOD5出水分别为47.80 mg/L和19.80 mg/L;氨氮去除率可达100%。发现厌氧区提前发生反硝化并一定程度上影响系统除磷效果;通过对各主要影响因素进行分析,认为低碳源的进水条件是影响系统同步脱氮除磷效果的关键因素;提出在进水口直接添加碳源以及分点进水的碳源分配＋辅助化学除磷的方式可强化氮磷去除效果。     

补充碳源对交替式厌氧/好氧生物滤池生物蓄磷/回收磷的影响

碳源不足是废水高效脱氮除磷、磷回收的限制因素,研究高效利用碳源同时能提高磷回收效果的的新工艺及其运行方式尤为重要。本研究采用连续式厌氧/好氧交替生物滤池(AABF)处理低碳磷比废水(COD/P=11),并研究碳源的补充方式(间歇型、连续型、连续循环型)、补充周期对生物滤池除磷、回收磷的影响;采用生物膜吸收并蓄积废水中的磷,并采用定期补充碳源方式诱导生物滤池内聚磷菌群(PAOs)充分释磷,以便形成高浓度的磷回收液,同时在PAOs胞内积累内源性碳,用于后续的生物除磷。结果表明,连续循环型碳源补充方式优于其他两种碳源补充方式,合理缩短碳源补充周期利于提高AABF的生物除磷以及磷回收效率;定期补充AABF进水碳源可增加AABF生物膜内聚羟基丁酸酯(PHB)含量、大幅提高AABF厌氧释磷浓度、提高厌氧释磷(磷回收)过程中PAOs的对碳源的利用效率。     

不同来源废水COD、TOC与Cl^-的关系

通过对含盐化工废水（A）、受潮汐影响的河流水（B）、城市生活污水处理厂排水（C）、采油废水（D）4种不同来源废水进行为期15 d的采样监测,测定了其COD、TOC和Cl^-浓度,分析比较了3种废水指标之间的关系,其中COD分别使用重铬酸钾法、氯气校正法和碘化钾碱性高锰酸钾法3种方法进行测定。实验结果表明,4种废水Cl^-浓度差异较大,盐化工废水A（21749 mg/L）〉采油废水D（7013 mg/L）〉受潮汐影响的河流水B（1807 mg/L）〉城市生活污水处理厂排水C（977 mg/L）;在15 d的监测周期内,盐化工废水（A）的TOC波动较大,其余3种废水的TOC浓度基本保持稳定,与Cl^-浓度变化没有直接的关系;4种不同废水的COD与Cl^-浓度之间具有显著的正相关性。通过分析比较表明,碘化钾碱性高锰酸钾法比较适合于盐化工废水（A）和采油废水（D）的测定,氯气校正法比较适合于城市生活污水处理厂排水（C）和采油废水（D）的测定,受潮汐影响的河流水样（B）波动较大,3种方法测得的COD浓度与Cl^-浓度的变化趋势没有显著差异。TOC较适合表征水质有机污染程度。     

不同来源废水COD、TOC与Cl-的关系

通过对含盐化工废水(A)、受潮汐影响的河流水(B)、城市生活污水处理厂排水(C)、采油废水(D)4种不同来源废水进行为期15 d的采样监测,测定了其COD、TOC和Cl-浓度,分析比较了3种废水指标之间的关系,其中COD分别使用重铬酸钾法、氯气校正法和碘化钾碱性高锰酸钾法3种方法进行测定.实验结果表明,4种废水Cl-浓...     

Coagulation and precipitation as post-treatment of anaerobically treated primary municipal wastewater.

The main objective of this study was to investigate the feasibility of coagulation as a post-treatment method of anaerobically treated primary municipal wastewater. Both mesophilic and ambient (20 degrees C) temperature conditions were investigated in a laboratory-scale upflow anaerobic sludge bed (UASB) reactor. In addition, optimization of the coagulant, both in terms of type and dose, was performed. Finally, phosphorus removal by means of aluminum and iron coagulation and phosphorus and ammonia nitrogen removal by means of struvite precipitation were studied. Anaerobic treatment of primary effluent at low hydraulic retention times (less than 15 hours) resulted in mean chemical oxygen demand (COD) removals ranging from 50 to 70%, while, based on the filtered treated effluent, the mean removals increased to 65 to 80%. Alum coagulation of the UASB effluent gave suspended solids removals ranging from approximately 35 to 65%. Turbidity removal reached up to 80%. Remaining COD values after coagulation and settling were below 100 mg/L, while remaining total organic carbon (TOC) levels were below 50 mg/L. Filterable COD levels were generally below 60 mg/L, while filterable TOC levels were below 40 mg/L. All coagulants tested, including prepolymerized aluminum and iron coagulants, demonstrated similar efficiency compared with alum for the removal of suspended solids, COD, and TOC. Regarding struvite precipitation, optimal conditions for phosphorus and nitrogen removal were pH 10 and molar ratio of magnesium: ammonia-nitrogen: phosphate-phosphorus close to the stoichiometric ratio (1:1:1). During struvite precipitation, removal of suspended solids reached 40%, while turbidity removal reached values up to 80%. The removal of COD was approximately 30 to 35%; yet, when removal of organic matter was based on the treated filterable COD, the removal increased to approximately 65%. In addition, nitrogen was removed by approximately 70%, while phosphorus removal ranged between approximately 30 and 45% on the basis of the initial phosphorus concentration. Finally, size fractionation of the organic matter (COD) showed that the various treatment methods were capable of removing different fractions of the organic matter.     

Degradation of 2,4-dichlorophenol by combining photo-assisted Fenton reaction and biological treatment.

The photo-Fenton reaction effect on the biodegradability improvement of 100 mg/L solution of 2,4-dichlorophenol (DCP) has been investigated. Biochemical oxygen demand (BOD) at 5 and 21 days, BODn/ chemical oxygen demand (COD) and BODn/total organic carbon (TOC) ratios, average oxidation state, and inhibition on activated sludge were monitored. For 50 mg/L hydrogen peroxide and 10 mg/L iron(II) initial concentrations and 40 minutes of reaction time in the photo-Fenton process, the biodegradability of the pretreated solution, measured as BOD5/COD ratio, was improved from 0 for the original DCP solution up to 0.18 (BOD21/COD = 0.24). At that point, all DCP was eliminated from the solution. To study the effect of the pretreatment step, the biological oxidation of pretreated solutions was tested in two semicontinuous stirred tank reactors, one operated with activated sludge and one with biomass acclimated to phenol. Results showed that more than 80% TOC removal could be obtained by codigestion of the pretreated solution with municipal wastewater. Total organic carbon removals of approximately 60% were also obtained when the sole carbon source for the aerobic reactors was the pretreated solution. The hydraulic retention times used in the bioreactors were of the same order of magnitude as those used at domestic wastewater treatment plants (i.e., between 12 and 24 hours). Kinetic studies based on pseudo-first-order kinetics have also been carried out. Constants were found to be in range 0.67 to 1.7 L x g total volatiles suspended solids(-1) x h(-1).     

Fenton-水解酸化-接触氧化处理模拟磷霉素钠制药废水

对模拟磷霉素钠制药废水进行Fenton-水解酸化-接触氧化小试处理实验,考察了COD、有机磷的去除效果,并对处理前后的废水进行了GC-MS分析。结果显示,增加了Fenton预处理后磷霉素钠制药废水的COD和有机磷分别降低到100和2 mg/L,去除率均可达87%以上,出水COD满足化学制药行业污染物排放标准(GB 21904-2008);Fenton过程对制药厂废水中的复杂有机物去除效果明显,GC-MS结果表明,出水中基本检测不到复杂有机物。与制药厂采用的水解酸化-接触氧化处理效果相比,增加Fenton预处理可以提高废水的可生化性和系统的处理效率。     

无砾石微孔管地下渗滤系统处理生活污水的中试研究

进行了无砾石微孔管地下渗滤系统处理生活污水的中试研究。基于不同土壤、不同管径、不同植物的协同效应,对比研究了不同系统处理污水中有机物、氮、磷和SS的去除效果及其影响因素。结果表明,不同土壤、不同管径及不同植物组成的系统,对生活污水中有机物、氮、磷和SS的去除效果差别较大。中试系统对COD、总磷、氨氮、总氮和SS的最佳去除率分别达到86.13%、90.20%、61.24%、65.49%和97.43%,对应的出水COD、总磷、氨氮、总氮和SS的平均浓度分别为64.29、0.69、22.13、26.19和5.56 mg/L。分析表明,进水SS浓度过高、外界温度下降等共同作用是导致系统对生活污水中NH4+-N和TN的去除率相对较低的主要原因。     

固定化膜生物反应器处理含抗生素污水

采用细菌固定化技术包埋活性污泥浓缩液,并利用A/O膜生物反应器处理含抗生素生活污水,考察了膜生物反应器在抗生素存在条件下降解有机物及氮素的性能,并对土霉素为代表的抗生素的去除效果进行分析。结果表明,人工模拟抗生素污水的COD、TOC、NH4+-N、TN及土霉素浓度分别为325～413、101.35～206.10、15.51～24.54、15.00～25.30和0.17～0.47 mg/L,水力停留时间为6、12和24 h的条件下,系统的出水平均COD、TOC、NH4+-N和TN分别维持在50、20、1和3 mg/L以下,对土霉素的平均去除率分别达到64%、72%和75%;研究还发现固定化膜生物反应器对进水中氨氮的波动具有良好的抗冲击负荷能力且可以延缓膜污染,正确调整水处理工艺的运行工序可以在提高水处理效率的同时有效降低水环境中的抗生素药物含量。     

水解-BCMBBR-混凝沉淀组合工艺处理低浓度污水的中试研究

采用水解-生物陶粒移动床(BCMBBR)-混凝沉淀组合工艺处理南方低浓度、低碳高氨氮生活污水(COD 110～140 mg/L、C/N 4～5),开展中试研究。结果表明,BCMBBR 20 d成功挂膜,快速启动;在水温25～29℃,HRT 8 h,气水比5∶1,混合液回流比150%,无混凝沉淀下运行,COD、SS和NH4+-N的平均去除率均在81%以上,TN平均去除率大于47%,而TP去除率较低;后接PAC+PAM强化混凝沉淀后运行,有效提高了TP去除率,出水TP在0.5 mg/L以下,稳定达到(GB18918-2002)一级A标准。曝气强度不同相应BCMBBR中的微生物相(微生物种类和数量)也不同,可根据微生物相来指导曝气强度的调节,实现BCMBBR的高效运行。该组合工艺处理废水运行的直接成本为0.24元/m3,是一种适合南方低浓度、低碳高氨氮生活污水的经济高效处理工艺。     

Enhancement of chemical-oxygen demand and color removal of distillery spent-wash by ozonation.

Distillery spent-wash has very high organic content (75,000 to 125,000 mg/L chemical-oxygen demand [COD]), color, and contains difficult-to-biodegrade organic compounds. For example, anaerobic treatment of the distillery spent-wash used in this study resulted in 60% COD reduction and low color removal. Subsequent aerobic treatment of the anaerobic effluent resulted in enhancement of COD removal to 66%. In this paper, the effect of ozonation on various properties of the anaerobically treated distillery effluent, including the effect on its subsequent aerobic biodegradation, was investigated. Ozonation of the anaerobically treated distillery effluent at various ozone doses resulted in the reduction of total-organic carbon (TOC), COD, COD/TOC ratio, absorbance, color, and increase in the biochemical-oxygen demand (BOD)/COD ratio of the effluent. Further, ozonation of the anaerobically treated distillery effluent at an ozone dose of 2.08 mg/mg initial TOC and subsequent aerobic biodegradation resulted in 87.4% COD removal, as compared to 66% removal when ozonation was not used.