添加天然沸石和石灰对土壤镉形态转化的影响

采用土壤培养实验,研究镉污染土壤中添加沸石、石灰及两者配施对土壤pH值和土壤镉形态变化的影响。结果表明,土壤pH值随沸石用量的增加而增加,随培养时间呈现先增加后下降并逐渐趋于稳定的趋势,但均高于对照。高剂量石灰的处理对土壤pH的影响最大,与对照相比土壤pH提高了3.33个单位。在土壤5~50 d培养过程中,石灰处理的土壤交换态镉含量呈现先逐渐降低而后略有升高的趋势,其余处理均呈下降趋势。培养50 d后,高剂量的沸石、石灰及高剂量沸石与石灰配施处理的土壤交换态镉含量从5 d时的67.54、61.95和55.56 mg/kg降低至54.65、49.93和45.96mg/kg。相关分析表明,不同培养时期交换态镉含量与土壤pH值呈负相关关系。在10个处理中,L2Z3(石灰2 g/kg土和沸石60 g/kg土)组合处理效果最好,使土壤交换态镉含量下降了34.68%,碳酸盐结合态镉含量上升了4.30%,铁锰氧化结合态镉含量上升了16.97%,有机结合态镉含量上升了1.31%,残渣态镉含量上升了12.11%。     

氮肥对污染农田土壤中铅的调控效应

用铅污染农田土壤做盆栽试验,研究了氮肥品种和施用量对小白菜吸收铅及土壤中铅形态的影响.结果表明,在氮肥施用量相同的条件下,施用不同形态氮肥对小白菜地上部及根系吸收铅有显著影响;适量的NH4NO3不会对小白菜地上部造成显著影响,增施Ca(NO3)2也不会造成小白菜地上部含铅量的继续增加;各施氮处理的土壤pH较不施氮处理的土壤pH均有不同程度的降低,且以(NH4)2SO4处理的土壤pH下降幅度最大,施用Ca(NO3)2的处理的土壤pH变化不显著;氮肥在一定程度上会影响土壤中各形态含铅量,其中对交换态、碳酸盐结合态、无定形氧化锰结合态,无定形氧化铁结合态及有机结合态含铅量影响较大,但并未改变各形态铅的分布顺序;小白菜吸收的铅主要来源于土壤中的交换态铅,但也可吸收部分碳酸盐结合态铅、铁锰氧化物结合态铅及有机结合态铅,甚至可吸收部分残渣态铅.     

几种典型土壤对电动修复镉污染效果的影响

选择5种典型土壤进行了镉污染的电动修复研究。结果表明,经12 d电动修复后,黑土、潮土、红壤、水稻土和黄棕壤中镉的去除率依次为16.7%、21.0%、47.1%、10.7%和12.6%。红壤靠阳极附近Cd含量由初期435 mg·kg-1降至32.4 mg·kg-1,迁移率高达92.5%。黑土、红壤和潮土都维持了较高的电流强度和电渗流量,但由于红壤对碱的缓冲能力较强,修复效果最好。水稻土中电渗流量高,但由于电流低,镉的去除率不高,说明电动修复中电迁移作用强于电渗析。修复后,土壤中可交换态镉、碳酸盐结合态镉、铁锰氧化物结合态镉总量减少,残渣态镉总量增加,有机结合态在阳极附近总量减少、阴极附近总量增加。上述结论揭示了电动修复的土壤镉污染的主要机制,通过镉的运动轨迹和形态分布,可预测不同土壤的电动修复效果,同时能改变不同土壤的电动修复策略,为场地修复提供参考。     

黔中地区不同污染风险等级黄壤镉形态分布特征

为探究喀斯特地区地带性黄壤的镉形态分布特征,在中国南方喀斯特中心区域——黔中地区进行了农田黄壤样品采集,并对其化学成分进行了定量分析,通过对土壤镉形态及pH、钙、镁的分析测定,探究了喀斯特背景对黄壤中镉形态分布的影响。结果表明,黔中地区黄壤全镉为0.184～3.316mg/kg,具有较大的空间差异,各形态镉含量随污染风险等级的提高而显著增加(p0.01)。黄壤中的镉主要以残渣态及可还原态存在,可交换态镉占全镉的17.52%(质量分数,下同)～22.83%,且随着风险等级的提高,可交换态镉向更为稳定的形态转变。可交换态镉与全镁、可交换态镁均显著负相关(p0.05),镁组分可在一定程度上降低黄壤中可交换态镉含量,对镉的生物有效性具有一定的调控作用。     

公路两侧土壤中铅和镉污染以及存在形态分布的分析

测定了土壤中铅、镉总量,并采用五级连续浸提法和石墨炉原子吸收分光光度法对北京市3条典型公路两侧的土壤样品中铅和镉的存在形态分布进行了测定.结果表明,所选3条公路出京方向右侧的土壤铅和镉污染严重,其铅、镉总量分别是北京地区土壤铅和镉含量背景值的1.62～6.69、5.97～18.74倍.土壤中铅主要以铁锰氧化物结合态、碳酸盐结合态、有机结合态和残渣态等形式存在,镉主要以铁锰氧化物结合态和残渣态形式存在,而活性强的离子交换态浓度均较低.不容忽视的是,铅和镉的碳酸盐结合态在碱性条件下稳定,但是具有遇酸释放的隐患.     

堆肥和腐殖酸对土壤锌铅赋存形态的影响

通过实验室土壤培养实验，研究2种有机物质——腐殖酸和堆肥，单独或者复合应用对土壤中铅锌形态转化的影响。经过1～3个月的培养，发现单独添加腐殖酸和堆肥均可以显著改变土壤中Zn、Pb形态转化，使它们从容易被植物吸收利用的交换态和碳酸盐结合态向难以被植物吸收利用的有机结合态和残渣态转化。与对照相比，单独添加10%堆肥和5%腐殖酸并培养1～3个月后，导致土壤交换态Zn比重分别由38%～51%下降到14%～21%和26%～46%；铁锰氧化物结合态Zn比重分别由23%～34%提高到33%～56%和26%～45%；碳酸盐结合态Pb比重分别由12%～25%下降到1%～15%和2%～15%；残渣态Pb比重分别由12%～14%提高到32%～45%和20%～23%。其他结合态的Zn和 Pb比重也有不同程度的变化。说明堆肥和腐殖酸均可以固定土壤中的Zn和 Pb。而当两者一起使用时，可以中和它们各自所引起土壤pH的变化，而对重金属固定效率更明显增强。研究还发现，不管是腐殖酸还是堆肥，对Pb的固定效果均好于对Zn的固定。     

含磷材料对矿区铅镉污染土壤重金属形态转化的影响

以湖南郴州东江湖风景区矿区遗留地重金属污染土壤为研究对象,研究了3种含P材料,及其与蒙脱石的组合材料,对矿区土壤铅镉污染的修复效果.实验设6组处理,分别为P1组、P2组、P3组、P1 +M组、P2+M组、P3 +M组,通过添加5％的稳定剂,稳定2d后,分析土壤中铅镉的形态变化.实验结果表明:添加含P材料,及组合材料后,土壤中铅镉的离子交换态、铁锰结合态、有机结合态大幅度降低,残渣态显著升高.对Pb离子转化效果均在90.00％以上,Cd离子的转化效率相对较差,最优P1处理效果为74.20％.离子交换态的减少,有效地降低了重金属的生物有效性,有效地降低了环境风险.同时,含P材料均增加了土壤有效磷的含量,对矿区土壤的肥力也有一定提升.     

硫化钠对土壤中铅镉的固定效果简

研究了硫化钠用于固定土壤中铅镉的可行性，考察了硫化钠用量及土壤pH、有机质对固定过程中土壤铅、镉赋存形态及固定效果的影响。结果表明，添加硫化钠可改变土壤中铅镉的形态分布，明显降低可交换态铅镉的含量。条件适当时，铅镉可交换态下降值分别为63%和73%。硫化钠在固定铅的过程中，固定效率对土壤pH、有机质含量的变化较为敏感，在有机质含量较低或酸性土壤中，硫化钠对铅固定效率较高；相对于铅，有机质含量和pH变化对镉的固定效率影响不是很大。     

金矿区高浓度砷污染土壤的稳定化处理

以粉煤灰、干化污泥、粉碎花生壳、硫酸亚铁(Fe_2SO_4)和磷酸二氢钾(KH_2PO_4)为稳定剂对矿区高浓度As污染土壤进行处理,通过土壤理化性质、重金属形态和浸出浓度变化等综合评估稳定剂对高浓度砷污染土壤的稳定化处理效果。结果表明,添加稳定剂可以提高土壤pH值、有机质含量和阳离子交换量。粉煤灰、干化污泥、粉碎花生壳、硫酸亚铁对土壤中的As有较好的稳定化作用,其中硫酸亚铁对土壤中As的稳定效果最好。同时添加10%粉煤灰、10%干化污泥和1%硫酸亚铁后,土壤中可交换态As、碳酸盐结合态As、铁锰氧化物结合态As、有机结合态As含量显著降低,降幅分别为62.3%、55.2%、29.6%、58.2%,残渣态As含量增加8.1%。添加粉煤灰、干化污泥、硫酸亚铁能显著降低土壤中As的浸出浓度,而添加KH_2PO_4会使土壤中As浸出浓度增加,移动性增强。当同时添加10%粉煤灰、10%干化污泥、1%粉碎花生壳和1%硫酸亚铁后,As浸出浓度最低(0.93 mg·L~(-1)),稳定效果最好,稳定化效率达到了74.8%。土壤中As的浸出浓度与可交换态As和碳酸盐结合态As呈显著正相关,与残渣态As呈显著负相关,可交换态As、碳酸盐结合态As和残渣态-As含量是影响土壤中As浸出浓度变化的主要因素。     

氯化铁和硫酸铁对酸性土壤中有效态镉和铅污染的修复作用

采用浸泡实验法研究了氯化铁和硫酸铁对酸性土壤中有效态镉和铅污染的修复效果,结果表明,氯化铁和硫酸铁均能有效去除土壤有效态镉和铅污染,Fe(Ⅲ)用量为50～100 mmol/kg时,有效态Cd和Pb的去除效果可达70％～96％.氯化铁和硫酸铁能去除土壤中的水溶态、碳酸盐结合态、腐殖酸结合态、铁锰氧化物结合态和强有机结合态Cd和Pb及交换态Cd.氯化铁和硫酸铁对Cd均既有洗脱修复作用又有固定修复作用,且洗脱修复作用的贡献稍大;氯化铁用量较小时(50 mmol/kg)对Pb既有固定修复又有洗脱修复作用,固定修复作用稍大;用量较大时(100 mmol/kg),对Pb只有洗脱修复作用.硫酸铁对Pb的修复作用则以固定修复作用为主,洗脱修复作用很小.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%(质量百分比).反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

Visualisation of the complexity of EUSES

The interdependencies of parameters applied in the models of EUSES are visualised in a directed connectivity graph. The parameters (inputs, defaults, state variables, outputs) are represented by boxes (nodes) and their relations by lines (edges). The visualisation, on the one hand, clarifies the complexity of the models in EUSES and, on the other hand, creates an overview and transparency. The parameters’ relations to each other can be recognised faster, and the models can be better understood. The complexity was quantified by the number (variety), kind (substance parameter, physico-chemical parameter, concentration, other parameters), and depth (dimension) of the parameter and the number of relations (connectivity). The variety of EUSES (without the modelsSimple Treat andSimple Box whose interior structure is not documented and without the effect and risk characterisation) amounts to 466, the connectivity to 961, and the maximal dimension is 21.