有机微污染物在污水处理过程中的变化研究

多环芳烃等有毒有机微污染物对污水处理综合指标BOD、COD和TOC等的贡献极小,但危害却很大.采用固相萃取的前处理方法和GC/MS、GC/μECD的分析方法,针对北京市某污水处理厂的总泵进水、二沉出水以及混凝沉淀出水中有机氯农药、多环芳烃和酚类的浓度进行分析.研究结果表明,在不同处理工艺段中,有机氯农药、多环芳烃和酚类的质量浓度分别为nd～10、nd～835、nd～3 248 μg/L.所有检出化合物均未超出中国污水与地表水相应标准限值,其中多环芳烃和酚残留水平较高,应为重点监测对象.这些污染物多数能够在二级处理过程中得到有效去除,但混凝沉淀并没有显著地进一步去除效果.     

北方某城市饮用水中多环芳烃的来源及其在水处理过程中的行为研究

采用固相萃取(SPE)样品富集前处理技术和气相色谱/质联联用(GC/MS)分析方法,对北方某工业城市给水系统中的多环芳烃类化合物的含量水平进行了研究.结果表明,该城市多环芳烃污染水平较高,但总浓度均未超过城市供水水质标准(CJ/T206-2005)中限值(2μg/L).近郊水库由于受到燃料燃烧产生的多环芳烃的污染,成为该市饮用水中多环芳烃污染的主要来源.传统的混凝-砂滤工艺对多环芳烃有较好的去除效果,总去除率可达55.9%.     

中国南方某城市自来水厂处理工艺对多环芳烃的去除效果研究

讨论了中国南方某城市自来水厂饮用水中的多环芳烃残留规律以及现有净水工艺对多环芳烃的去除效果。研究结果表明,该自来水厂饮用水中检出多环芳烃以2~4环芳烃为主,强致癌性高环数多环芳烃均在检出限以下,且多环芳烃总量未超出中国供水行业标准(2000年)的相关限值。各处理工艺段中,砂滤过程对多环芳烃的去除效果最好,相较于原水对多环芳烃总量的去除率可达64%。     

城市污水处理系统中典型内分泌干扰物的迁移转化特征

采用固相萃取-气相色谱法研究了邯郸某污水处理系统污水和污泥中内分泌干扰物的存在水平,在污水和污泥中均检测出多氯联苯类、多环芳烃类、邻苯二甲酸酯类、酚类和有机氯农药五大类内分泌干扰物,除多氯联苯浓度在μg水平外,其他4种内分泌干扰物的浓度均在ng水平。污水处理系统进水以及污泥中它们的平均浓度分别在19.43 ng/L~60.82μg/L和43.94 ng/g~167.45μg/g之间,污水经过处理后,平均去除率在16.6%~77.9%之间。在污水处理过程中,多氯联苯、多环芳烃和有机氯农药主要通过污泥吸附去除,而邻苯二甲酸酯和酚类则主要通过生物降解作用去除。     

强化活性炭吸附技术深度处理焦化废水的可行性研究

采用混凝沉淀、活性炭吸附以及混凝沉淀 活性炭吸附工艺对焦化厂生化出水进行深度处理.单独混凝沉淀或活性炭吸附均可以将水样中COD降到100 mg/L以下,达到国家污水一级排放标准和冷却用水建议标准.活性炭根据不同的材质和进水而表现出不同的吸附性能,对于焦化厂生化出水,煤质炭Ⅰ和果壳炭均表现出良好的吸附效果,并使出水COD＜100 mg/L,但处理成本较高.混凝沉淀 活性炭吸附工艺充分发挥适合去除大分子污染物的混凝沉淀与适宜去除小分子污染物的活性炭吸附技术两者的协同增效作用,吸附单元采用廉价的煤质炭,使出水水质达到个别生产或生活用水回用标准,并且降低深度处理成本.研究结果表明,混凝沉淀 活性炭吸附作为焦化厂生化出水回用工艺是经济可行的.     

中国南方某城市自来水厂处理工艺对多环芳烃的去除效果研究

讨论了中国南方某城市自来水厂饮用水中的多环芳烃残留规律以及现有净水工艺对多环芳烃的去除效果。研究结果表明，该自来水厂饮用水中检出多环芳烃以2～4环芳烃为主，强致癌性高环数多环芳烃均在检出限以下，且多环芳烃总量未超出中国供水行业标准(2000年)的相关限值。各处理工艺段中，砂滤过程对多环芳烃的去除效果最好，相较于原水对多环芳烃总量的去除率可达64％。     

常用城市污水再生处理工艺净化效果比较分析

以城市污水回用为目的,对常规混凝-沉淀-过滤工艺、臭氧生物活性炭和直接超滤等深度处理技术处理城市污水处理厂二级出水的效果进行了试验研究,对各种工艺的去除效果进行了评价。     

应用活性炭再生含多环芳烃植物油的可行性及性能评价

为利用植物油去除污染土壤中的多环芳烃,研究了应用活性炭F400吸附柱再生含多环芳烃植物油的可行性,对含高浓度多环芳烃的植物油进行二级再生处理,优化了过程参数,比较了原植物油和经活性炭再生的植物油去除土壤中多环芳烃能力的差别.结果表明,活性炭吸附法可以实现含多环芳烃植物油的再生,证明了修复策略的可行性.二级处理可以进一步吸附植物油中的多环芳烃,且高分子量多环芳烃几乎完全被去除.再生植物油和原植物油去除土壤中多环芳烃的能力没有明显差别.     

混凝-Fenton法处理采油污水的研究

对采油废水进行混凝预处理后进行了Fenton处理 ,确定了Fenton试剂处理采油废水的最佳配比为H2 O2 ∶Fe2 +=5 0mmol L :1mmol L。同时利用GC MS色谱图探讨了混凝 -Fenton法对有机物的去除机理。结果表明 :混凝工艺去除了75 %的有机污染物 ,碳数低于 2 1的烷烃去除率可达到 80 %以上 ,同时还去除了所有的多环芳烃 ,但是对苯酚类物质的去除率只有 5 0 %。在Fenton过程中 ,铁的水解吸附和OH·的氧化作用并存 ,采油污水经过 12 0min的Fenton处理后 ,其中的烷烃类物质、酚类物质、多环芳烃物质能被完全氧化。     

人工湿地处理系统中多环芳烃的行为

采用Oasis HLB柱固相萃取的前处理技术,以气相色谱质谱联用仪(GC/MS)的分析方法,对我国北方永定河上游黑土洼人工湿地中多环芳烃污染的特征以及分布规律进行了研究.结果表明,该湿地系统以低环数多环芳烃污染为主,其中浓度最高的是菲和蒽,未检出高环数(5环、6环)多环芳烃.通过比较进水和出水的浓度,湿地系统总体上不能有效去除进水中的多环芳烃.但是比较不同工艺单元进出水浓度,复氧、植物根系及微生物等均影响到多环芳烃的去除效果,去除率在28%～65%之间.     

Disinfection by-products in Finnish drinking waters

Disinfection by-products (DBPs) were measured in plant effluents of 35 Finnish waterworks, which utilized different treatment processes and raw water sources. DBPs were measured also from the distribution systems of three waterworks. Di- and trichloroacetic acids, and chloroform were the major DBPs found in treated water samples. The concentration of six haloacetic acids (HAA6) exceeded the concentrations of trihalomethanes (THMs). Chlorinated drinking waters (DWs) originating from surface waters contained the highest concentration of HAA6 and THMs: 108 and 26 microg/l, respectively. The lowest concentrations of DBPs were measured from ozonated and/or activated carbon filtrated and chloraminated DWs. Higher concentrations of HAA6, THMs, and adsorbable organic halogens were measured in summer compared to winter. The levels of chlorinated acetic acids, chloroform, and bromodichloromethane correlated positively with mutagenicity. Past mutagenicity levels of DWs were examined. A major reduction in the use of prechlorination, increased use of chloramine disinfection, and better removal of organic carbon were the most important reasons for the 69% decrease in mutagenicity from 1985 to 1994.     

Evaluation of activated carbon fiber filter for sampling of organochlorine pesticides in environmental water samples

A simple method for quantitative analyses of organic chlorine pesticides (OCPs) in environmental water samples such as rainwater, river water and seawater using activated carbon fiber filters (ACFF) is described. ACFF was used as adsorbent to collect the chemicals in water samples. The collection of OCPs was completed almost for one day by stirring the mixture of the sample and the ACFF chips at room temperature. The adsorbed OCPs on the ACFF could be extracted easily with toluene-ethanol (4:1) mixed solvent. The purified extract by a florisil column chromatograph was followed by the analysis using high-resolution gas chromatograph/high-resolution mass spectrometer. Recoveries of OCPs spiked to actual samples such as rainwater, river water and seawater samples were approximately more than 80%, and the coefficients of variations were within 10%. This method was applied to the actual samples and was confirmed to be applicable for monitoring sub-ng/l level OCPs in environmental water samples.     

Passive air sampler as a tool for long-term air pollution monitoring: Part 1. Performance assessment for seasonal and spatial variations

The potential of passive air sampling devices (polyurethane foam disks) to assess the influence of local sources on the quality of the surrounding environment was investigated. DEZA Valasske Mezirici, a coal tar and mixed tar oils processing plant, and Spolana Neratovice, a chemical factory with the history of high production of organochlorinated pesticides (OCPs), were selected as the point sources of PAHs, and OCPs, respectively. Levels of PCBs, OCPs and PAHs were determined for all sampling sites and sampling periods. The study brought useful data about the air concentrations of POPs in the investigated regions. More important, it provided information on the transport and fate of POPs in the vicinity of local sources of contamination useful for the estimation of their influence. Very good capability of passive samplers to reflect temporal and spatial fluctuation in concentrations of persistent organic pollutants in the ambient air was confirmed which makes them applicable for monitoring on the local scale.     

Residues of polycyclic aromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides in organically-farmed vegetables

The residues of polyaromatic hydrocarbons (PAHs), polychlorinated biphenyls (PCBs) and organochlorine pesticides (OCPs) in soils from organic farms and their uptake by four varieties of organic-produced potatoes and three varieties of organic carrots from England were investigated. Samples of the soils, crop peels and cores were all Soxhlet-extracted in triplicate, cleaned up by open-column chromatography and analysed by a multi-residue analytical method using gas chromatography with mass selective detection. The concentrations of PAHs, PCBs and OCPs in soils from organic farms ranged from 590+/-43 to 2301+/-146 microg/kg, 3.56+/-0.73 to 9.61+/-1.98 microg/kg and 52.2+/-4.9 to 478+/-111 microg/kg, respectively. Uptake by different crop varieties were 8.42+/-0.93 to 40.1+/-4.9 microg/kg sigmaPAHs, 0.83+/-0.19 to 2.68+/-0.94 microg/kg sigmaPCBs and 8.09+/-0.83 to 133+/-27 microg/kg sigmaOCPs. Residue uptake from soils depended on plant variety; Desiree potato and Nairobi carrot varieties were more susceptible to PAH contamination. Likewise, uptake of PCBs and OCPs depended on potato variety. There were significant positive correlations between the PCB and OCP concentrations (P<0.05) in soils and carrots but no significant correlation was found between the concentrations of any contaminants in soils and potatoes. Peeling carrots and potatoes was found to remove 52-100% of the contaminant residues depending on crop variety and the properties of the contaminants. Soil-crop bioconcentration factors (BCFs) decreased with increasing logK(ow) for PAHs up to about 4.5 and for PCBs up to about 6.5, above which no changes were discernible for either class of contaminants. No relationship was observed between soil-crop BCFs and logK(ow) for OCPs, most likely because their concentrations were low and variable.     

Use of semipermeable membrane devices (SPMDs)

Triolein-containing semipermeable membrane devices (SPMDs) were employed as passive samplers to provide data on the bioavailable fraction of organic, waterborne, organochlorine pesticides (OCPs), polychlorinated biphenyls (PCBs) and polynuclear aromatic hydrocarbons (PAHs) in streams flowing through a highly polluted industrial area of Bitterfeld in Saxony-Anhalt, Germany. The contamination of the region with organic pollutants originates in wastewater effluents from the chemical industry, from over one-hundred years of lignite exploitation, and from chemical waste dumps. The main objective was to characterise time-integrated levels of dissolved contaminants, to use them for identification of spatial trends of contamination, and their relationship to potential pollution sources. SPMDs were deployed for 43 days in the summer of 1998 at four sampling sites. The total concentration of pollutants at sampling sites was found to range from a low of 0.8 microgram/SPMD to 25 micrograms/SPMD for PAHs, and from 0.4 microgram/SPMD to 22 micrograms/SPMD for OCPs, respectively. None of the selected PCB congeners was present at quantifiable levels at any sampling site. A point source of water pollution with OCPs and PAHs was identified in the river system considering the total contaminant concentrations and the distribution of individual compounds accumulated by SPMDs at different sampling sites. SPMD-data was also used to estimate average ambient water concentrations of the contaminants at each field site and compared with concentrations measured in bulk water extracts. The truly dissolved or bioavailable portion of contaminants at different sampling sites ranged from 4% to 86% for the PAHs, and from 8% to 18% for the OCPs included in the estimation. The fraction of individual compounds found in the freely dissolved form can be attributed to the range of their hydrophobicity. In comparison with liquid/liquid extraction of water samples, the SPMD method is more suitable for an assessment of the background concentrations of hydrophobic organic contaminants because of substantially lower method quantification limits. Moreover, contaminant residues sequestered by the SPMDs represent an estimation of the dissolved or readily bioavailable concentration of hydrophobic contaminants in water, which is not provided by most analytical approaches.     

自然水体中主要有毒有机物的研究进展

介绍了主要有毒有机物多环芳烃(PAHs)、多氯联苯(PCBs)、有机氯农药(OCPs)在环境中的危害及其来源,着重评述了近年来中国自然水体中和沉积物中该类污染物的研究进展,指出新的检测技术的开发、有毒有机物的生殖毒性和生态环境风险影响方法学的研究及污染区域污染控制、消减及修复是今后该领域的工作重点.     

Reproductive toxicity assessment of surface water of the Tai section of the Yangtze River, China by in vitro bioassays coupled with chemical analysis

Reproductive toxicity of organic extracts of the surface water from the Tai section of the Yangtze River was assessed by in vitro cytotoxity assays and selected persistent organic pollutants including PCBs, OCPs and PAHs were quantified by instrumental analysis. Eleven of the US EPA priority PAHs were detected. Individual PAHs were found to range from 0.7 to 20 ng/L. Concentrations of BaP did not exceed the national drinking water source quality standard of China. However, a 286-fold concentrated organic extract induced significant reproductive toxicity in adult male rats. The morphology of cells, MTT assay and LDH release assay were all affected by exposure to the organic extracts of water. The results of the reproductive toxicity indicated that PAHs posed the greatest risk of the chemicals studied. The compounds present in the water could be bioconcentrated and result in adverse effects.     

Selective removal of organochlorine pesticides (OCPs) from aqueous solution by triolein-embedded composite adsorbent

A novel composite adsorbent (CA-T) was used for the selective removal of organochlorine pesticides (OCPs) from aqueous solution. The adsorbent was composed of the supporting activated carbon and the surrounding triolein-embedded cellulose acetate membrane. Scanning electron microscopy (SEM), N₂ adsorption isotherms and fluorescence methods were used to characterize the physicochemical properties of CA-T. Triolein was perfectly embedded in the cellulose acetate membrane and deposited on the surface of activated carbon. The adsorbent was stable in water and no triolein leakage was detected during the test periods. Some organochlorine pesticides (OCPs), such as dieldrin, endrin, aldrin, and heptachlor epoxide, were used as model contaminants and removed by CA-T in laboratory batch experiments. The adsorption isotherm followed the Freundlich equation and the kinetic data fitted well to the pseudo-second-order reaction model. Results also indicated that CA-T appeared to be a promising adsorbent with good selectivity and satisfactory removal rate for lipophilic OCPs from aqueous solutions when present in trace amounts. The adsorption rate and removal efficiency for lipophilic OCPs were positively related to their octanol-water partition coefficients (log K _ow). Lower residual concentrations of OCPs were achieved when compared to granular activated carbon (GAC).