稀盐酸预处理对稻草厌氧消化的影响

为探明稀酸预处理对稻草厌氧消化的影响,采用不同浓度的稀盐酸溶液对稻草进行了浸泡预处理,并在完全混合厌氧消化条件下,研究了稻草厌氧发酵过程中的产气量、甲烷含量,发酵液中COD、pH值及挥发性脂肪酸(VFA)的变化情况.结果表明,增大稀盐酸溶液浓度会提高稻草厌氧消化反应的效果.分别经4%、8%和12%的稀盐酸溶液浸泡预处理...     

含固率对牛粪常温厌氧消化的影响

在常温、pH值为7.0下,采用10 L玻璃瓶作为反应器对含固率(TS)分别为2%、6%、10%和14%的4组牛粪溶液进行厌氧消化实验,系统运行48 d,分析了厌氧消化过程中的COD(化学需氧量)、pH、VFA(挥发性脂肪酸)和产气量的变化。结果表明,进料TS是影响牛粪厌氧消化产气效果的重要因素,调节牛粪进料TS至10%,可以使其厌氧消化获得最佳的产气效果,COD去除率为24.6%,产气中甲烷含量为56.1%。     

碳氮比对鸭粪中温厌氧消化的影响

在中温(35±1)℃、6%的料液浓度、pH为中性条件下,采用10 L玻璃瓶作为反应器对碳氮比(C/N)分别为15、20、25和35的4组鸭粪溶液进行厌氧消化实验,系统运行30 d,分析了厌氧消化过程中的COD(化学需氧量)、pH、VFA(挥发性脂肪酸)和产气量的变化。结果表明,碳氮比是影响鸭粪厌氧消化过程的重要因素,调节鸭粪碳氮比至25,可以使其厌氧消化获得最佳的产气效果,COD去除率为24.06%,原料干物质产气率为0.178 m3/kg,产气中甲烷含量为71.5%,产甲烷率为0.127 m3/kg。     

污泥加热预处理对中温厌氧消化的影响

对污泥加热预处理给中温厌氧混合消化和污泥单独消化带来的影响进行了研究.研究结果表明,污泥加热预处理有利于提高混合消化对 COD 的去除率,尤其是 SCOD 的去除率由 77%增长到 93%,但不利于 TS 和 VS 的去除;而对污泥单独消化,预处理则不利于有机物的去除.采用加热预处理后的污泥进样,混合消化和污泥单独消化的甲烷产气量均有所提高.     

超声波预处理对牛粪厌氧消化的影响

以牛粪为研究对象,考察超声波预处理对牛粪厌氧消化的影响。结果表明,适宜强度的超声波预处理对牛粪厌氧消化有一定促进作用。与未经预处理牛粪相比,在100、175、250W超声波预处理下牛粪厌氧消化的最高产气速率从127.02mL/d分别提高到179.26、212.73、298.71mL/d,累计产气量从1 674.18mL分别提高到2 279.81、2 508.05、2 730.66mL,消化液达到最低pH的时间从30d分别缩短至25、15、10d;消化液最大溶解性COD从14 881mg/L分别提高到16 450、17 080、19 250mg/L,牛粪挥发性固体的生物降解率从44.7%分别提高到55.4%、57.3%、61.7%。超声波强度过大将对微生物造成破坏,降低生物反应活性,从而抑制牛粪厌氧消化。经325W超声波预处理后,牛粪厌氧消化的最高产气速率、累计产气量等参数均不及未经预处理牛粪。在未来实际应用中,应注意控制超声波强度,以达到最优预处理效果。     

超声联合热碱预处理对剩余污泥厌氧消化的影响

以不同含固率剩余污泥为研究对象,在超声联合热碱预处理条件下,考察了污泥在厌氧消化过程中的减量以及细胞物质释放的特性。厌氧消化阶段,经过预处理作用的预处理泥挥发性悬浮固体(VSS)、溶解性COD(SCOD)的去除率均高于原泥,且VSS、SCOD去除率均随污泥含固率的增加而减少,SCOD去除率(X_(SCODr),%)和产气量(Y_(QY),mL/g)存在定量函数关系,即Y_(QY)=-0.148 7 X~2_(SCODr)+24.771 X_(SCODr)-775.68,同时SCOD去除率与VSS去除率(X_(VSSr),%)存在线性关系X_(SCODr)=0.533 3 X_(VSSr)+43.411。预处理对污泥在厌氧消化阶段氨氮、磷酸根磷的影响也随含固率的增大而减小,含固率为1.5%的预处理泥氨氮、磷酸根磷浓度相较原泥增幅最大,依次增长了97.3%、166.0%。     

零价铁对餐厨垃圾厌氧消化产甲烷的影响研究

针对餐厨垃圾厌氧消化酸抑制而造成的消化效率低和产气量低等问题,在中温((37±1)℃)条件下,通过向厌氧消化器中投加不同量的零价铁(Fe~0),考察其对餐厨垃圾厌氧消化过程中pH、挥发性脂肪酸(VFAs)、日产气量、COD及累计产气量的影响。结果表明,投加1 000mg/L Fe~0对餐厨垃圾厌氧消化酸抑制的缓冲作用最好,可保证厌氧系统的稳定及最佳运行,第10天的VFAs转化率比对照组(CK组)提高了36.21%;COD去除率比CK组高13.10百分点;日产气量峰值为1 728mL;25d的累积产气量为10 108mL,比CK组高35.01%。     

臭氧预处理—厌氧消化工艺促进剩余污泥减量化的研究

主要研究了臭氧氧化对剩余污泥的破解效果及污泥厌氧消化效率的影响.结果表明,随着臭氧投加量的增加,悬浮物(SS)、可挥发性悬浮物(VSS)逐步减少,而剩余污泥上清液中的溶解性COD(SCOD)、总有机碳(TOC)、蛋白质和多糖则明显增加.经臭氧预处理(臭氧投加量为0.050 g(以每克SS计))后,剩余污泥中温(35℃)厌氧消化效率明显提高,经65d稳定运行后,总挥发性固体(TVS)去除率为67.58％,与未经臭氧预处理的剩余污泥相比提高50.61％;甲烷平均产率为0.303 L(以每克TVS计),与未经臭氧预处理的剩余污泥相比提高54.59％.可见,臭氧预处理能有效促进污泥厌氧消化,从而达到污泥减量的目的.     

电弧流溶胞技术促进污泥厌氧消化

为提高污水厂处理污泥时的厌氧消化速率,利用电弧流溶胞技术处理剩余污泥,研究电弧流溶胞技术对污泥破解预处理效果的影响。实验结果表明,与未经预处理的污泥相比,电弧流溶胞处理能够明显提高污泥厌氧消化效率,增加有机物含量和沼气产量。其中,经处理后的污泥TS、VS剩余量分别降低了8.3%和6.3%,COD增加了11.9%。厌氧系统平均产气量平均增加79.76 L/d,增加率45.82%,甲烷含量增加1.03 L/d,增加率102%。由此说明,电弧流溶胞技术可以提高厌氧消化反应中有机物的去除率,有效促进厌氧消化中污泥的水解过程,显著增加甲烷气体的产生量。在综合考虑运行费用和污泥消化效果的前提下,采取适宜的电弧流强化处理措施有一定的积极意义。     

竹叶与餐厨垃圾厌氧共消化工艺

将黄金竹和毛竹的竹叶分别与餐厨垃圾厌氧共消化,通过分析消化过程中的产气量、pH、COD、NH4+-N和VFAs变化,探讨添加不同竹叶对餐厨垃圾厌氧消化效果的影响.实验结果表明,添加毛竹叶显著增强了餐厨垃圾的厌氧消化能力.毛竹叶+餐厨垃圾组的总产气量是餐厨垃圾对照组单独厌氧消化总产气量的3.28倍,甲烷总产量为10.1 L,COD去除率高达83.0％.而添加黄金竹叶对餐厨垃圾厌氧消化的影响则不明显,可能因为黄金竹叶在消化过程中释放了大量挥发性脂肪酸(VFAs),造成体系酸中毒.     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.