负载TiO2/Fe^3＋的玻璃纤维反应器光催化苯酚

以玻璃纤维为载体,将TiO2负载到其表面形成了空间玻璃纤维反应器,引入Fe3＋作为掺杂改性离子,形成了负载TiO2/Fe^3＋的空间玻璃纤维光催化反应器,并以高压汞灯为光源进行了光催化降解水中苯酚的实验研究,考察了影响苯酚光催化降解的因素,确定了在UV365-250 W光源照射下,pH为3-5,O2通入量1.0 L/（min.L）,反应器内上升流速为0.7 m/min等实验条件下,初始浓度为30 mg/L的苯酚废水经120 min光催化反应后,降解率可达到85%,矿化率可达80%。     

Fe/TiO2光催化降解水溶液中的4-氯苯酚

以TiO2-P25及FeC2O4为前驱物制备了Fe3 掺杂TiO2光催化剂--Fe/TiO2.X射线衍射结果表明,500 ℃煅烧温度下的Fe/TiO2主要是锐态矿晶型,当掺Fe3 量为0.5%(质量分数,下同)时,Fe3 以取代掺杂形式进入TiO2晶格,而当掺Fe3 量达5.0%时,则出现α-Fe2O3的特征衍射峰;900 ℃煅烧温度下的Fe/TiO2则均为金红石晶型,掺Fe3 量达2.0%～5.0%时,出现Fe2TiO5的特征衍射峰.4-氯苯酚的光催化实验结果表明,煅烧温度及Fe3 掺杂量对Fe/TiO2的光催化活性有显著影响,以煅烧温度500 ℃及掺Fe3 量0.5%的Fe/TiO2为光催化剂,反应80 min,4-氯苯酚的降解率达100%,总有机碳去除率约95%.     

Fe~(3+)掺杂TiO_2/凹凸棒复合材料的光催化性能

采用酸催化的溶胶-凝胶法制备了一系列Fe3+掺杂TiO2/凹凸棒(Fe3+-TiO2/ATP)复合光催化剂材料。在可见光条件下,以亚甲基蓝(MB)溶液的光催化降解反应,评价了样品的光催化性能,研究了TiO2负载量、Fe3+掺杂量和焙烧温度对复合材料光催化性能的影响。在单因素实验的基础上,采用正交实验设计(L25(53))优化了催化剂的制备条件。光催化实验结果表明,MB在复合材料上的光催化降解反应遵循Langmuir-Hinshelwood(L-H)动力学模型。正交实验结果表明,当TiO2负载量为15%、Fe3+掺杂量为0.5%和焙烧温度为550℃时,得到的复合材料对MB的光催化降解效率最佳,测得表观反应速率常数kapp为6.09×10-3min-1,反应4 h后MB的降解率(Dt)可达75.88%,相同实验条件下与P25(1.51×10-3min-1)相比较,反应速率提高了4.03倍,降解率提高了45.05%。另外,复合材料的沉降性能优于P25,易于分离,是一类有应用前景的复合光催化剂。     

漂浮负载型光催化剂制备及降解草甘膦研究

以漂珠(FP)为载体,采用溶胶-凝胶-浸渍法制备了漂浮负载型CdS/TiO2/FP复合膜光催化剂,通过SEM、XRD对其结构进行了表征.以甘草膦农药的光催化降解为模型反应,使用不同光源研究了CdS/TiO2/FP的光催化性能,探讨了影响催化剂活性的因素及采用太阳光做光源处理草甘膦的可行性.结果表明,经4层镀膜500℃热处理的20%(w/w)CdS/TiO2/FP光催化剂具有良好的光催化性能,最佳降解条件为:催化剂加入量3 g/L,初始pH 7～9,Fe2 浓度为2.0×10-3 mol/L.通气量200 mL/min.在最佳条件下,对135 mg/L草甘膦溶液降解率可以分别达到96.3%(125 W高压汞灯,60 min)和82.4%(太阳光,180 min).     

固体超强酸SO42-/TiO2-SnO2／Ce4+ 光催化降解含酚废水

采用共沉淀-浸渍法制备了固体超强酸SO24-/TiO2-SnO2/Ce4+,并用XRD、SEM等方法对其结构进行了表征。以苯酚的光催化降解为反应模型,确定了最佳的工艺条件和催化剂再生方法。结果表明:在pH值为6,苯酚初始浓度为50mg/L,催化剂投加量4 g/L,光照距离12 cm,光照时间为150 min,降解率达67.73%,添加助催化剂H2O2后,反应60 min,苯酚降解率达到86.33%,催化剂的最佳再生方法是先用1 mol/L的硫酸浸渍24 h后,在450℃下焙烧6 h。     

负载型TiO2固定相光催化降解含酚废水的试验研究

以20W紫外灯为光源,研究了将TiO2粉末负载在硅胶颗粒上,对含酚废水进行光催化降解.由试验得出光催化反应过程中的工艺条件,在此基础上添加H2O2、Fe3+、Cu2+,反应1 h后,苯酚的降解率达95%以上.     

Fenton试剂协同TiO_2光催化降解三氯乙酸及协同机理

为了研究Fenton试剂协同TiO2光催化降解三氯乙酸(TCAA)的反应及其协同机理,在自制的光催化反应装置中分别考察了Fenton、UV/TiO2及Fenton/UV/TiO23个反应对TCAA的降解情况。研究结果表明,在TCAA初始浓度为2.0 mg/L,TiO2用量为1.0 g/L,紫外辐射光源为15 W(λmain=254 nm)的实验条件下,Fenton试剂协同TiO2光催化降解TCAA反应在pH 3~7范围内均有较高的降解率;TCAA在Fenton、UV/TiO2及Fenton/UV/TiO23个反应中的一级反应速率常数分别为0.0009、0.0131和0.0456 min-1;Fenton试剂与TiO2光催化反应间存在较明显的协同效应,其协同机理主要体现在两个方面:一是紫外光激发Fe(OH)2+和H2O2分解产生更多的·OH,二是Fenton试剂中部分被氧化成的Fe3+可与TiO2表面的光生电子结合被还原为Fe2+,抑制了光生电子与空穴的复合,从而提高了TiO2光催化降解TCAA的效率。     

SO2-4/TiO2光催化降解苯酚

以工业硫酸氧钛为原料水解制得SO42-/TiO2光催化剂,并以苯酚为目标降解物,考察了SO24-/TiO2的光催化性能。结果表明:随着SO42-/TiO2制备过程中焙烧温度的升高,其光催化活性逐渐增加,650℃焙烧获得的SO24-/TiO2的光催化活性最好,此后再升高温度会因催化剂中硫的挥发而下降;在确定苯酚原液初始浓度为50 mg/L条件下,SO42-/TiO2的光催化降解苯酚的最佳工艺条件为反应时间2 h、苯酚pH为7、催化剂用量1 g/L。XRD、SEM和FTIR的分析结果显示实验温度下制得的SO42-/TiO2均为锐钛型TiO2;其间掺杂的SO24-在TiO2表面分散性较好,没有聚集成大的颗粒;红外分析的结果初步判定低温(<550℃)焙烧制得的催化剂SO42-在TiO2表面是螯合双配位吸附,高温焙烧时(>550℃)SO42-在TiO2表面是桥式配位吸附。     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La₂O₃(0.5%)-ZnO(20%)-TiO₂/沸石复合光催化剂，以20 W紫外灯为光源，在自制的光催化反应器中降解活性艳红K-2BP，考察了光照时间、空气通入量、催化剂用量、溶液初始浓度、H₂O₂与Fe³⁺投加量等对活性艳红K-2BP光催化降解率的影响。结果表明，当溶液初始浓度为60 mg/L，催化剂投加量为12 g/L，通气量为1 200 mL/min，光照2.5 h，活性艳红K-2BP的降解率可达99.2%；H₂O₂和Fe³⁺投加量为4 mL/L和3 g/L时，光照1 h活性艳红K-2BP降解率分别为100%和97.2%。紫外可见吸收光谱显示，LZTZ光催化剂可有效降解印染废水。     

La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La2O3/ZnO/TiO2复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La2O3/ZnO/TiO2的光催化性能.结果表明:当锌和镧的掺杂量w(zno)=20%,w(La2O3)=0.5%,煅烧温度为500℃时,La2O3/ZnO/TiO2复合光催化剂的光催化活件最高;当催化荆投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La2O3/ZnO/TiO2对活性艳红K-2BP的降解效果最好.实验证明.La2O3/ZnO/TiO2对活性艳红K-2BP的降解遵从Lang-muir-Hinshelwood动力学模型,测得其反应速率常数k=11.5 mg/(L·min);吸附常数K=2.88×10-2L/mg.     

固体超强酸SO4^2-／TiO2-SnO2／Ce^4＋光催化降解含酚废水

采用共沉淀-浸渍法制备了固体超强酸SO4^2-／TiO2-SnO2／Ce^4＋，并用XRD、SEM等方法对其结构进行了表征。以苯酚的光催化降解为反应模型，确定了最佳的工艺条件和催化剂再生方法。结果表明：在pH值为6，苯酚初始浓度为50mg／L，催化剂投加量4g／L，光照距离12cm，光照时间为150min，降解率达67．73％，添加助催化剂H2O2后，反应60min，苯酚降解率达到86．33％，催化剂的最佳再生方法是先用1mol／L的硫酸浸渍24h后，在450℃下焙烧6h。     

Optimization of photo-Fenton process parameters on carbofuran degradation using central composite design

Carbofuran, one of the most toxic and biorefractory carbamate compounds, is widely used in insecticides in Taiwan (9-18% of total insecticides production per year). In the present study, a central composite design experiment was used to study the effect of photo-Fenton treatment on carbofuran solution and to optimize the process variables such as carbofuran concentration (1-100 mg L(-1)), H(2)O(2) dosage rate (0.25-6 mg L(-1) min(-1)) and Fe(3+) dosage (1-50 mg L(-1)), which influenced the efficiency of carbofuran degradation and mineralization. The results indicated that all the variables investigated in this study had significant roles in the degradation and mineralization of carbofuran in solution. The carbofuran degradation and mineralization efficiencies were increased with increase in H(2)O(2) dosage rate and Fe(3+) dosage, and with decrease in carbofuran concentration. Furthermore, optimum values of both H(2)O(2) dosage rate and Fe(3+) dosage were found to shift to higher values as carbofuran concentration increased. Based on the model obtained in this study, optimum H(2)O(2) dosage rate and Fe(3+) dosage were found to be 4 mg L(-1) min(-1) and 20 mg L(-1), respectively, for 51 mg L(-1) of carbofuran concentration. Under these conditions, carbofuran was completely removed within 30 min and coupled with 78% mineralization at the end of experiment.     

外负载Ce-TiO2/活性炭复合体对亚甲基蓝光催化

用超临界流体沉积法处理过的活性炭(AC)为载体,钛酸丁酯为前驱物,硝酸铈为掺杂剂,乙醇为溶剂,制备了外负载TiO2-Ce/Csurf复合材料。在紫外灯照射下,以亚甲基蓝溶液为标准模拟降解物,研究了复合体不同热处理温度、不同浓度、不同亚甲基蓝浓度、不同铈掺杂量以及不同反应温度对光催化性能的影响。结果表明:外负载催化剂的催化性能要高于纯TiO2和体负载催化剂。铈离子掺杂能抑制TiO2晶粒生长,阻碍了TiO2由锐钛矿型向金红石型的转变。当铈离子掺杂量为1.5%,热处理温度为600℃,亚甲基蓝溶液初始浓度为5.5 mg/L,样品浓度为1.5 g/L时,光催化性能最好。     

Photo-oxidation of cork manufacturing wastewater

Several photo-activated processes have been investigated for oxidation of a cork manufacturing wastewater. A comparative activity study is made between different homogeneous (H2O2/UV-Vis and H2O2/Fe2+/UV-Vis) and heterogeneous (TiO2/UV-Vis and TiO2/H2O2/UV-Vis) systems, with degradation performances being evaluated in terms of total organic carbon (TOC) removal. Results obtained in a batch photo-reactor show that photo-catalysis with TiO2 is not suitable for this kind of wastewater while the H2O2/UV-Vis oxidation process, for which the effect of some operating conditions was investigated, allows to remove 39% of TOC after 4 h of operation (for C(H2O2)=0.59 M, pH=10 and T=35 degrees C). The combined photo-activated process, i.e., using both TiO2 and H2O2, yields an overall TOC decrease of 46% (for C(TiO2)=1.0 gl(-1)). The photo-Fenton process proved to be the most efficient, proceeds at a much higher oxidation rate and allows to achieve 66% mineralization in just 10 min of reaction time (for C(H2O2)=0.31 M, T=30 degrees C, Fe2+:H2O2=0.12 (mol) and pH=3.2).     

三维电极/电-Fenton法降解苯酚

采用电-Fenton耦合三维电极法处理苯酚模拟废水，研究了活性炭作为第三电极的三维电极体系中苯酚的去除效果，重点考察了常温下初始pH值、电流强度、Fe²⁺浓度等因素对苯酚降解的影响。结果表明：在常温下，曝气速率20 L/min，初始pH=3，电流强度为0.3 A/m²，Fe²⁺浓度为0.1 mmol/L，反应时间60 min时，废水的苯酚的氧化降解率为91%，COD去除率为64%。在此条件下，三维电极/电-Fenton表现出较强的氧化能力，具有较好的去除效果，可应用于含苯酚废水的处理。     

TiO2光催化处理络合铜废水的实验研究

研究了以悬浮态TiO2为催化剂,在紫外光的作用下对络合铜废水进行光催化反应,分别考察了常温下TiO2投加量、反应时间、废水初始pH值、反应气氛等因素对处理效果的影响,并探讨了反应机理。结果表明:TiO2投加量为2 g/L,废水pH=4,300 W高压汞灯照射下,载入60 mL/min的空气反应40 min,120 mg/L EDTA络合铜废水的Cu(II)与COD的去除率达到最高,分别为96.56%和57.67%。     

Fe-exchanged zeolite as the effective heterogeneous Fenton-type catalyst for the organic pollutant minimization: UV irradiation assistance

The issue of investigations in this study was an application of heterogeneous Fenton-type catalyst, Fe-exchanged zeolite FeZSM5, for the minimization of phenol and overall organic content in the model wastewater. Applied treatment systems included variation of heterogeneous and homogeneous Fenton-type catalyst with and without the assistance of UV irradiation, FeZSM5/H2O2, Fe2+/H2O2/NH4ZSM5, Fe3+/H2O2/NH4ZSM5, UV/FeZSM5/H2O2, UV/Fe2+/H2O2/NH4ZSM5 and UV/Fe3+/H2O2/NH4ZSM5. Processes efficiency was evaluated on the basis of phenol removal, mineralization extent, H2O2 consumption and concentration of iron ions in the bulk after the treatment. By all applied systems, complete phenol removal was achieved in less than 30 min of treatment time. Systems including heterogeneous Fenton-type catalyst showed somewhat lower mineralization efficiency in comparison to the corresponding systems applying homogeneous Fenton-type catalysts and the addition of synthetic zeolite NH4ZSM5. Significantly lower concentration of iron ions in the bulk after the treatment could give these systems, particularly UV/FeZSM5/H2O2, a great advantage over the homogeneous Fenton-type systems.     

Performance of photocatalytic reactors using immobilized TiO2 film for the degradation of phenol and methylene blue dye present in water stream

TiO2 thin film photocatalyst was successfully synthesized and immobilized on glass reactor tube using sol-gel method. The synthesized TiO2 coating was transparent, which enabled the penetration of ultra-violet (UV) light to the catalyst surface. Two photocatalytic reactors with different operating modes were tested: (a) tubular photocatalytic reactor with re-circulation mode and (b) batch photocatalytic reactor. A new proposed TiO2 synthesized film formulation of 1 titanium isopropoxide: 8 isopropanol: 3 acetyl acetone: 1.1 H2O: 0.05 acetic acid (in molar ratio) gave excellent photocatalytic activity for degradation of phenol and methylene blue dye present in the water. The half-life time, t1/2 of photocatalytic degradation of phenol was 56 min at the initial phenol concentration of 1000 microM in the batch reactor. In the tubular photocatalytic reactor, 5 re-circulation passes with residence time of 2.2 min (single pass) degraded 50% of 40-microM methylene blue dye. Initial phenol concentration, presence of hydrogen peroxide, presence of air bubbling and stirring speed as the process variables were studied in the batch reactor. Initial methylene blue concentration, pH value, light intensity and reaction temperature were studied as the process variables in the tubular reactor. The synthesized TiO2 thin film was characterized using SEM, XRD and EDX analysis. A comparative performance between the synthesized TiO2 thin film and commercial TiO2 particles (99% anatase) was evaluated under the same experimental conditions. The TiO2 film was equally active as the TiO2 powder catalyst.