Heterogeneous photocatalytic oxidation of cyprodinil and fludioxonil in leaching water under solar irradiation

The efficiency of ZnO and TiO₂ suspensions in the photocatalytic degradation of two fungicides (cyprodinil and fludioxonil) in leaching water was investigated. The experiments were carried out at pilot plant scale using compound parabolic collectors under natural sunlight. The blank experiments for both irradiated compounds solutions showed that both oxides strongly enhanced the removal of the fungicides. The addition of an oxidant (Na₂S₂O₈) to the ZnO or TiO₂ increased the rate of photooxidation. The degradation of cyprodinil and fludioxonil followed first order kinetics according to the Langmuir-Hinshelwood model. Complete degradation of both fungicides was achieved within 4 h (t_30W = 18 min) when treated with illuminated ZnO. The disappearance time (DT₇₅), when referred to the normalized illumination time (t_30W), was lower than 40 and 550 min (t_30W = 2 and 40 min) for both fungicides using ZnO or TiO₂, respectively. ZnO appeared to be more effective in cyprodinil and fludioxonil oxidation than TiO₂ probably due to its nonstoichiometry.     

Photolytic degradation of decabromodiphenyl ethane (DBDPE)

The photolytic degradation of decabromodiphenyl ethane (DBDPE), an alternative flame retardant to decabromodiphenyl ether, was investigated in a variety of matrixes (n-hexane, tetrahydrofuran, methanol/water, humic acid/water, and silica gel) by irradiation under ultraviolet light and in n-hexane under natural light. Photolytic degradation of DBDPE occurs in all the matrixes investigated within the irradiation period (<320 min). The degradation experiments showed varied reaction rates, dependent on the matrixes, with increasing half-lives (t_1/2) in the order of tetrahydrofuran (t_1/2 = 6.0 min) > n-hexane (t_1/2 = 16.6 min) > humic acid/water (30 < t_1/2 < 60) > silica gel (t_1/2 = 75.9 min) > methanol/water (t_1/2 > 240 min). The reaction in tetrahydrofuran, n-hexane, and silica gel matrixes can be described by the pseudo first order kinetics. Nevertheless, the matrixes have little effect on the degradation product distributions of DBDPE. A numbers of debrominated intermediates were identified. The degradation involves the initial formation of nona-BDPEs and the subsequent decomposition of these congeners to lower brominated congeners (octa- and hepta-BDPEs) within the irradiation time. To our knowledge, the present work is the first attempt to investigate the photolytic degradation kinetics and the identification of intermediates, as well as the degradation mechanism, during the degradation of DBDPE. Further research is needed to understand the photolytic degradation pattern of DBDPE in the natural environment.     

Photolytic and photocatalytic degradation of 6-chloronicotinic acid

This work describes for the first time the photolytic and photocatalytic degradation of 6-chloronicotinic acid (6CNA) in double deionised water, which is a degradation product of neonicotinoid insecticides imidacloprid and acetamiprid, and it is known to appear in different environmental matrices. Photolytic experiments were performed with three UVA (ultraviolet A) polychromatic fluorescent lamps with broad maximum at 355 nm, while photocatalytic experiments were performed using immobilised titanium dioxide (TiO₂) on six glass slides in the spinning basket inside a photocatalytic quartz cell under similar irradiation conditions. Photolytic degradation revealed no change in concentration of 6CNA within 120 min of irradiation, while the photocatalytic degradation within 120 min, obeyed first-order kinetics. The observed disappearance rate constant was k = 0.011 ± 0.001 min⁻¹ and t_1/2 was 63.1 ± 5.5 min. Mineralisation rate was estimated through total organic carbon (TOC) and measurements revealed no carbon removal in case of photolysis after 120 min of exposure. However in photocatalytic experiments 46 ± 7% mineralisation was achieved within 120 min of irradiation. Nevertheless, the removal of total nitrogen (TN) was not observed across all experiments. Ion chromatographic analyses indicated transformation of chlorine atoms to chloride and increase of nitrate(V) ions only via photocatalytic experiments. Efficiency of selected advanced oxidation process (AOP) was investigated through toxicity assessment with Vibrio fischeri luminescent bacteria and revealed higher adverse effects of treated samples on bacteria following photocatalytic degradation in spite of the fact that higher mineralisation was achieved. New hydroxylated product generated in photocatalytic experiments with TiO₂, was confirmed with liquid chromatography-electro spray ionisation mass spectrometry (LC-ESI-MS/MS) analyses, gas chromatography-mass spectrometry (GC-MS) and nuclear magnetic resonance spectroscopy (¹H NMR).     

Toxicity of nanoparticulate and bulk ZnO, Al2O3 and TiO2 to the nematode Caenorhabditis elegans

Limited information is available on the environmental behavior and associated potential risk of manufactured oxide nanoparticles (NPs). In this research, toxicity of nanoparticulate and bulk ZnO, Al₂O₃ and TiO₂ were examined to the nematode Caenorhabditis elegans with Escherichia coli as a food source. Parallel experiments with dissolved metal ions from NPs were also conducted. The 24-h median lethal concentration (LC₅₀) and sublethal endpoints were assessed. Both NPs and their bulk counterparts were toxic, inhibiting growth and especially the reproductive capability of the nematode. The 24-h LC₅₀ for ZnO NPs (2.3 mg L⁻¹) and bulk ZnO was not significantly different, but significantly different between Al₂O₃ NPs (82 mg L⁻¹) and bulk Al₂O₃ (153 mg L⁻¹), and between TiO₂ NPs (80 mg L⁻¹) and bulk TiO₂ (136 mg L⁻¹). Oxide solubility influenced the toxicity of ZnO and Al₂O₃ NPs, but nanoparticle-dependent toxicity was indeed observed for the investigated NPs.     

Microbial degradation of pharmaceuticals in estuarine and coastal seawater

Microbial degradation rates were measured for 19 pharmaceuticals in estuarine and coastal surface water samples. Antipyrine, carbamazepine, cotinine, sulfamethoxazole, and trimethoprim were the most refractory (half-lives, t_1/2 = 35 to >100 days), making them excellent candidates for wastewater tracers. Nicotine, acetaminophen, and fluoxetine were labile across all treatments (t_1/2 = 0.68-11 days). Caffeine, diltiazem, and nifedipine were also and relatively labile in all but one of the treatments (t_1/2 = 3.5-13 days). Microbial degradation of caffeine was further confirmed by production ¹⁴CO₂. The fastest decay of non-refractory compounds was always observed in more sewage-affected Jamaica Bay waters. Degradation rates for the majority of these pharmaceuticals are much slower than reported rates for small biomolecules, such as glucose and amino acids. Batch sorption experiments indicate that removal of these soluble pharmaceuticals from the water column to sediments is a relatively insignificant removal process in these receiving waters.     

Acute effects of Fe₂O₃, TiO₂, ZnO and CuO nanomaterials on Xenopus laevis

Metal oxide nanomaterials have exhibited toxicity to a variety of aquatic organisms, especially microbes and invertebrates. To date, few studies have evaluated the toxicity of metal oxide nanomaterials on aquatic vertebrates. Therefore, this study examined effects of ZnO, TiO₂, Fe₂O₃, and CuO nanomaterials (20-100 nm) on amphibians utilizing the Frog Embryo Teratogenesis Assay Xenopus (FETAX) protocol, a 96 h exposure with daily solution exchanges. Nanomaterials were dispersed in reconstituted moderately hard test medium. These exposures did not increase mortality in static renewal exposures containing up to 1000 mg L⁻¹ for TiO₂, Fe₂O₃, CuO, and ZnO, but did induce developmental abnormalities. Gastrointestinal, spinal, and other abnormalities were observed in CuO and ZnO nanomaterial exposures at concentrations as low as 3.16 mg L⁻¹ (ZnO). An EC₅₀ of 10.3 mg L⁻¹ ZnO was observed for total malformations. The minimum concentration to inhibit growth of tadpoles exposed to CuO or ZnO nanomaterials was 10 mg L⁻¹. The results indicate that select nanomaterials can negatively affect amphibians during development. Evaluation of nanomaterial exposure on vertebrate organisms are imperative to responsible production and introduction of nanomaterials in everyday products to ensure human and environmental safety.     

Cellular uptake and mutagenic potential of metal oxide nanoparticles in bacterial cells

Extensive production and consumption of nanomaterials such as ZnO and TiO₂ has increased their release and disposal into the environment. The accumulation of nanoparticles (NPs) in ecosystem is likely to pose threat to non-specific targets such as bacteria. The present study explored the effect of ZnO and TiO₂ NPs in a model bacterium, Salmonella typhimurium. The uptake of ZnO and TiO₂ bare NPs in nano range without agglomeration was observed in S. typhimurium. TEM analysis demonstrated the internalization and uniform distribution of NPs inside the cells. Flow cytometry data also demonstrates that both ZnO and TiO₂ NPs were significantly internalized in the S. typhimurium cells in a concentration dependent manner. A significant increase in uptake was observed in the S. typhimurium treated even with 8 and 80 ng mL⁻¹ of ZnO and TiO₂ NPs with S9 after 60 min, possibly the formation of micelles or protein coat facilitated entry of NPs. These NPs exhibited weak mutagenic potential in S. typhimurium strains TA98, TA1537 and Escherichia coli (WP2uvrA) of Ames test underscoring the possible carcinogenic potential similar to certain mutagenic chemicals. Our study reiterates the need for re-evaluating environmental toxicity of ZnO and TiO₂ NPs presumably considered safe in environment.     

Zero valent iron mediated degradation of the pharmaceutical diazepam

Parameters that influence the zero valent iron mediated degradation of the pharmaceutical diazepam (DZP) were evaluated including the iron concentration and its pre-treatment, the effect of complexation with EDTA and oxic versus anoxic condition. It was observed that acid pre-treatment of iron particles is important for degradation efficiency and that H₂SO₄ is a better choice than HCl, resulting in higher degradation of DZP. Under oxic conditions, the degradation of DZP achieved 96% after 60 min using Fe⁰ (25 g L⁻¹) pre-treated with H₂SO₄ in the presence of EDTA (119 mg L⁻¹), while mineralization achieved around 60% after the same time. Under anoxic conditions, degradation occurred, however at lower extent, achieving 67% after 120 min. The addition of EDTA improved the treatment efficiency in 20% leading to 99% DZP degradation after 120 min. The first intermediates formed during DZP degradation were identified using LC/MS analysis and revealed the formation of mono- and di-hydroxylated products from DZP during Fe⁰/EDTA/O₂ degradation, which evidences that OH was the main oxidizing species formed in this process.     

Antimicrobial activity of metal oxide nanoparticles supported onto natural clinoptilolite

The antimicrobial activity of Cu₂O, ZnO and NiO nanoparticles supported onto natural clinoptilolite was investigated in the secondary effluent under dark conditions. After 24 h of contact the Cu₂O and ZnO nanoparticles reduced the numbers of viable bacterial cells of Escherichia coli and Staphylococcus aureus in pure culture for four to six orders of magnitude and showed consistent 100% of antibacterial activity against native E. coli after 1 h of contact during 48 exposures. The antibacterial activity of NiO nanoparticles was less efficient. The Cu₂O and NiO nanoparticles showed 100% of antiprotozoan activity against Paramecium caudatum and Euplotes affinis after 1 h of contact, while ZnO nanoparticles were less efficient. The morphology and crystallinity of the nanoparticles were not affected by microorganisms. The metal oxide nanoparticles could find a novel application in the disinfection of secondary effluent and removal of pathogenic microorganisms in the tertiary stage of wastewater treatment.     

Sorption-desorption behavior of metsulfuron-methyl and sulfosulfuron in soils

Sorption of metsulfuron-methyl and sulfosulfuron were studied in five Indian soils using batch sorption method. Freundlich adsorption equation described the sorption of herbicides with K_f (adsorption coefficient) values ranging between 0.21 and 1.88 (metsulfuron-methyl) and 0.37 and 1.17 (sulfosulfuron). Adsorption isotherms were L-type suggesting that the herbicides sorption decreased with increase in the initial concentration of the herbicide in the solution. The K_f for metsulfuron-methyl showed good positive correlation with silt content (significant at p = 0.01) and strong negative correlation with the soil pH (significant at p = 0.05) while sorption of sulfosulfuron did not correlate with any of the soil parameter. Desorption of herbicides was concentration dependent and, in general, sulfosulfuron showed higher desorption than the metsulfuron-methyl. The study indicates that these herbicides are poorly sorbed in the Indian soil types and there may be a possibility of their leaching to lower soil profiles.     

Chronic toxicity of ZnO nanoparticles, non-nano ZnO and ZnCl2 to Folsomia candida (Collembola) in relation to bioavailability in soil

The chronic toxicity of zinc oxide nanoparticles (ZnO-NP) to Folsomia candida was determined in natural soil. To unravel the contribution of particle size and free zinc to NP toxicity, non-nano ZnO and ZnCl₂ were also tested. Zinc concentrations in pore water increased with increasing soil concentrations, with Freundlich sorption constants K_f of 61.7, 106 and 96.4 l/kg (n = 1.50, 1.34 and 0.42) for ZnO-NP, non-nano ZnO and ZnCl₂ respectively. Survival of F. candida was not affected by ZnO-NP and non-nano ZnO at concentrations up to 6400 mg Zn/kg d.w. Reproduction was dose-dependently reduced with 28-d EC50s of 1964, 1591 and 298 mg Zn/kg d.w. for ZnO-NP, non-nano ZnO and ZnCl₂, respectively. The difference in EC50s based on measured pore water concentrations was small (7.94-16.8 mg Zn/l). We conclude that zinc ions released from NP determine the observed toxic effects rather than ZnO particle size.     

Nitrous oxide and methane emission from a flooded rice field as influenced by separate and combined application of herbicides bensulfuron methyl and pretilachlor

Combination of divergent active principles to achieve broad-spectrum control is gaining popularity to manage the weed menace in intensive agriculture. However, such application could have non-target impacts on the soil processes affecting soil ecology and environmental interactions. A field experiment was conducted to investigate the impact of separate and combined applications of herbicides bensulfuron methyl and pretilachlor on the emission of N₂O and CH₄, and related soil and microbial parameters in a flooded alluvial field planted to rice cv Lalat. Single application of the herbicide bensulfuron methyl or pretilachlor resulted in a significant reduction of N₂O and CH₄ emissions while the combination of these two herbicides distinctly increased N₂O and CH₄ emissions. Cumulative N₂O emissions (kg N₂O-N) followed the order of bensulfuron methyl (0.35 kg ha⁻¹) < pretilachlor (0.36 kg ha⁻¹) < control (0.45 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (0.49 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (0.54 kg ha⁻¹). Cumulative CH₄ emissions (kg CH₄), on the other hand, followed the order of bensulfuron methyl (47.89 kg ha⁻¹) < pretilachlor (73.17 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% single dose (93.50 kg ha⁻¹) < control (106.54 kg ha⁻¹) < bensulfuron methyl 0.6% + pretilachlor 6.0% double dose (124.67 kg ha⁻¹). The inhibitory effect of separate application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% on N₂O emission was linked to lower mineral N, lower denitrifying and nitrifying activity and low denitrifier and nitrifier populations. Inhibitory effect on CH₄ emission, on the contrary, was linked to prevention in the drop of redox potential, lower readily mineralizable carbon (RMC) and microbial biomass carbon (MBC) contents as well as lower methanogenic and higher methanotrophic bacterial population. Admittedly, stimulatory effect of combined application of herbicides bensulfuron methyl 0.6% and pretilachlor 6.0% at double dose on N₂O and CH₄ emission was related to reversal of the identified indicators of inhibition. Results indicate that while individual application of herbicides bensulfuron methyl 0.6% or pretilachlor 6.0% can reduce N₂O and CH₄ emission from flooded soil planted to rice, their combined application at normal dose can keep the emission at a comparatively lower level with significantly higher grain yield as compared to the herbicides applied alone.     

Aerobic degradation of tetrabromobisphenol-A by microbes in river sediment

This study investigated the aerobic degradation of tetrabromobisphenol-A (TBBPA) and changes in the microbial community in river sediment from southern Taiwan. Aerobic degradation rate constants (k₁) and half-lives (t_1/2) for TBBPA (50 μg g⁻¹) ranged from 0.053 to 0.077 d⁻¹ and 9.0 to 13.1 d, respectively. The degradation of TBBPA (50 μg g⁻¹) was enhanced by adding yeast extract (5 mg L⁻¹), sodium chloride (10 ppt), cellulose (0.96 mg L⁻¹), humic acid (0.5 g L⁻¹), brij 30 (55 μM), brij 35 (91 μM), rhamnolipid (130 mg L⁻¹), or surfactin (43 mg L⁻¹), with rhamnolipid yielding a higher TBBPA degradation than the other additives. For different toxic chemicals in the sediment, the results showed the high-to-low order of degradation rates were bisphenol-A (BPA) (50 μg g⁻¹) > nonylphenol (NP) (50 μg g⁻¹) > 4,4′-dibrominated diphenyl ether (BDE-15) (50 μg g⁻¹) > TBBPA (50 μg g⁻¹) > 2,2′,3,3′,4,4′,5,5′,6,6′-decabromodiphenyl ether (BDE-209) (50 μg g⁻¹). The addition of various treatments changed the microbial community in river sediments. The results also showed that Bacillus pumilus and Rhodococcus ruber were the dominant bacteria in the process of TBBPA degradation in the river sediments.     

Quantitative assessment of the toxic effects of heavy metals on 1,2-dichloroethane biodegradation in co-contaminated soil under aerobic condition

1,2-Dichloroethane (1,2-DCA) is one of the most hazardous pollutant of soil and groundwater, and is produced in excess of 5.44 × 10⁹ kg annually. Owing to their toxicity, persistence and potential for bioaccumulation, there is a growing interest in technologies for their removal. Heavy metals are known to be toxic to soil microorganisms at high concentrations and can hinder the biodegradation of organic contaminants. In this study, the inhibitory effect of heavy metals, namely; arsenic, cadmium, mercury and lead, on the aerobic biodegradation of 1,2-DCA by autochthonous microorganisms was evaluated in soil microcosm setting. The presence of heavy metals was observed to have a negative impact on the biodegradation of 1,2-DCA in both soil samples tested, with the toxic effect being more pronounced in loam soil, than in clay soil. Generally, 75 ppm As³⁺, 840 ppm Hg²⁺, and 420 ppm Pb²⁺ resulted in 34.24%, 40.64%, and 45.94% increase in the half live (t_½) of 1,2-DCA, respectively, in loam soil, while concentrations above 127.5 ppm Cd²⁺, 840 ppm Hg²⁺ and 420 ppm of Pb²⁺ and less than 75 ppm As³⁺ was required to cause a >10% increase in the t_½ of 1,2-DCA in clay soil. A dose-dependent relationship between degradation rate constant (k₁) of 1,2-DCA and metal ion concentrations was observed for all the heavy metals tested, except for Hg²⁺. This study demonstrated that different heavy metals have different impacts on the degree of 1,2-DCA degradation. Results also suggest that the degree of inhibition is metal specific and is also dependent on several factors including; soil type, pH, moisture content and available nutrients.     

Abatement of spinosad and indoxacarb residues in pure water by photocatalytic treatment using binary and ternary oxides of Zn and Ti

The photodegradation of indoxacarb, a broad spectrum foliar insecticide and spinosad, a natural insecticide containing two active ingredients, spinosyn A (major component) and spinosyn D (minor component), was studied in aqueous suspensions of binary (ZnO and TiO₂) and ternary (Zn₂TiO₄ and ZnTiO₃) oxides under artificial light (300–460 nm) irradiation. As expected, the influence of the semiconductor materials on the degradation of both was very significant in all cases. Photocatalytic experiments showed that the addition of semiconductors in tandem with Na₂S₂O₈ as electron acceptor strongly improved the removal of indoxacarb and spinosad in water compared with the photolytic tests. The reaction rates significantly increased, especially for the ZnO/Na₂S₂O₈ and TiO₂/Na₂S₂O₈ systems. The first-order equation (monophasic model) satisfactorily explained the disappearance process, although it offered no explanation for the small concentrations remaining in the process.     

Glucuronidation of hydroxylated polybrominated diphenyl ethers and their modulation of estrogen UDP-glucuronosyltransferases

Polybrominated diphenyl ethers (PBDEs) can be metabolically converted to their hydroxylated metabolites (OH-PBDEs). The estrogenic effects of PBDEs may be mediated by OH-PBDEs, but the mechanisms of which are still not understood. This study investigated the glucuronidation of 11 OH-PBDEs and their potential in modulating UDP-glucuronosyltransferases (UGTs) activity of 17β-estradiol (E2) in rat liver microsomes. The number of bromine atoms at phenolic ring was observed as the most influential factor of OH-PBDEs glucuronidation. 2′-OH-BDE-28 having one bromine atom at phenolic ring showed the fastest metabolic rates with t_1/2 value of 3.86 min, while 6-OH-BDE-137 having four bromine atoms at phenolic ring was the poorest substrate with t_1/2 value over 60 min. Regarding to the modulation of E2-UGTs activity, the phenolic hydroxyl group in OH-PBDEs played an essential role. Depending on the substitution patterns of bromine and hydroxyl group, OH-PBDEs inhibited or stimulated E2-UGTs activity. Ten of OH-PBDEs inhibited both 3-glucuronidation and 17-glucuronidation of E2 with IC₅₀ values varying from 3.80 to 129.38 μM, while 3′-OH-BDE-100 exhibited stimulating effects on 3-glucuronidation with EC₅₀ value of 35.95 μM. Kinetic analysis suggested noncompetitive inhibition mode of E2 glucuronidation by 3′-OH-BDE-7, 6-OH-BDE-47 and 2′-OH-BDE-68 with K_i values varying from 11.95 to 67.22 μM. This study demonstrated OH-PBDEs exhibited large interindividual differences in glucuronidation and modulation of E2-UGTs activity. By inhibiting the formation of E2 glucuronidation, OH-PBDEs may increase E2 bioavailability in target tissue, thereby exerting an indirect estrogenic effect.     

Bacterial toxicity comparison between nano- and micro-scaled oxide particles

Toxicity of nano-scaled aluminum, silicon, titanium and zinc oxides to bacteria (Bacillus subtilis, Escherichia coli and Pseudomonas fluorescens) was examined and compared to that of their respective bulk (micro-scaled) counterparts. All nanoparticles but titanium oxide showed higher toxicity (at 20 mg/L) than their bulk counterparts. Toxicity of released metal ions was differentiated from that of the oxide particles. ZnO was the most toxic among the three nanoparticles, causing 100% mortality to the three tested bacteria. Al₂O₃ nanoparticles had a mortality rate of 57% to B. subtilis, 36% to E. coli, and 70% to P. fuorescens. SiO₂ nanoparticles killed 40% of B. subtilis, 58% of E. coli, and 70% of P. fluorescens. TEM images showed attachment of nanoparticles to the bacteria, suggesting that the toxicity was affected by bacterial attachment. Bacterial responses to nanoparticles were different from their bulk counterparts; hence nanoparticle toxicity mechanisms need to be studied thoroughly.     

Hydrolysis of di-n-butyl phthalate, butylbenzyl phthalate and di(2-ethylhexyl) phthalate in human liver microsomes

Diester phthalates are industrial chemicals used primarily as plasticizers to import flexibility to polyvinylchloride plastics. In this study, we examined the hydrolysis of di-n-butyl phthalate (DBP), butylbenzyl phthalate (BBzP) and di(2-ethylhexyl) phthalate (DEHP) in human liver microsomes. These diester phthalates were hydrolyzed to monoester phthalates (mono-n-butyl phthalate (MBP) from DBP, mono-n-butyl phthalate (MBP) and monobenzyl phthalate (MBzP) from BBzP, and mono(2-ethylhexyl) phthalate (MEHP)) by human liver microsomes. DBP, BBzP and DEHP hydrolysis showed sigmoidal kinetics in V-[S] plots, and the Hill coefficient (n) ranged 1.37-1.96. The S₅₀, V_max and CL_max values for DBP hydrolysis to MBP were 99.7 μM, 17.2 nmol min⁻¹ mg⁻¹ protein and 85.6 μL min⁻¹ mg⁻¹ protein, respectively. In BBzP hydrolysis, the values of S₅₀ (71.7 μM), V_max (13.0 nmol min⁻¹ mg⁻¹ protein) and CL_max (91.3 μL min⁻¹ mg⁻¹ protein) for MBzP formation were comparable to those of DBP hydrolysis. Although the S₅₀ value for MBP formation was comparable to that of MBzP formation, the V_max and CL_max values were markedly lower (<3%) than those for MBzP formation. The S₅₀, V_max and CL_max values for DEHP hydrolysis were 8.40 μM, 0.43 nmol min⁻¹ mg⁻¹ protein and 27.5 μL min⁻¹ mg⁻¹ protein, respectively. The S₅₀ value was about 10% of DBP and BBzP hydrolysis, and the V_max value was also markedly lower (<3%) than those for DBP hydrolysis and MBzP formation for BBzP hydrolysis. The ranking order of CL_max values for monoester phthalate formation in DBP, BBzP and DEHP hydrolysis was BBzP to MBzP ? DBP to MBP > DEHP to MEHP > BBzP to MBP. These findings suggest that the hydrolysis activities of diester phthalates by human liver microsomes depend on the chemical structure, and that the metabolism profile may relate to diester phthalate toxicities, such as hormone disruption and reproductive effects.     

Adsorption and breakdown of penicillin antibiotic in the presence of titanium oxide nanoparticles in water

The fate and transport of antibiotics in natural water systems is controlled in part by interactions with nanometer (10⁻⁹ m) metal oxide particles. Experiments were performed by mixing solutions of ampicillin (AMP), a common, penicillin-class human and veterinary antibiotic, with 25 nm-TiO₂ (anatase) nanoparticles at different pH conditions. Both sorption and degradation of AMP were observed in the AMP-nanoparticle solutions. For AMP concentrations from ∼3 μM to 2.9 mM the overall AMP removal from solution can be described by linear isotherms with removal coefficients (K_r) of 3028 (±267) L kg⁻¹ at pH 2, 11,533 (±823) L kg⁻¹ at pH 4, 12,712 (±672) L kg⁻¹ at pH 6, and 1941 (±342) L kg⁻¹ at pH 8. Mass spectral analysis of AMP solutions after removal of the solid nanoparticles yielded ions that indicate the presence of peniclloic acid, penilloic acid and related de-ammoniated by-products as possible compounds resulting from the degradation of AMP at the TiO₂ surface.