微波热解城市污水污泥的H2S释放影响因素研究

利用微波热解城市污水污泥是实现污泥无害化、减量化和资源化的有效出路之一,但热解过程中产生的恶臭气体(如H2S等)也会对大气环境造成严重的影响.以微波热解城市污水污泥10 min所收集的气体为研究对象,研究了热解终温、污泥含水率、升温速率及矿物催化剂种类4个因素对热解过程中H2S产量的影响.结果表明,随着热解终温的升高,城市污水污泥微波热解过程中的H2S产量逐渐上升,800℃时H2S产量为5.86 mg/g(以干污泥计,下同);含水率在50％～80％时,随着含水率的增加,城市污水污泥微波热解过程中的H2S产量逐渐上升,当含水率增至90％时,污泥出现了泥水分层现象,致使后续热解反应无法进行,故没有H2S产生;升温速率越快,热解反应的活化能越高,反应不易进行,H2S产量降低;添加矿物催化剂能有效固硫,且雷尼镍基催化剂的效果更好,热解终温为800℃时的H2S产量为4.15 mg/g,较不添加矿物催化剂时降低约30％;可通过铜铁吸收法和活性炭吸附两步工艺对热解产生的H2S加以吸收处理,处理后的H2S排放浓度满足《恶臭污染物排放标准》(GB 14554-93)中的厂界一级标准限值.     

污泥连续式微波热解制备生物气

采用升温迅速的微波能作为热源,利用自主设计微波设备对含水率为82%(m/m)的湿污泥进行高温热解实验。采用单因素实验法,探究热解终温、停留时间、活性炭添加量对污泥热解生物气组分和含量的影响规律,确定连续式运行的最佳工况条件:热解终温900℃,停留时间50 min,活性炭添加比例为30%,热解功率1 600 W;在此基础上进行连续12h微波高温热解实验,共热解污泥56 kg,产生生物气32.26 kg,热解油10.98 kg,固体残渣12.66 kg,产气转化率高达57.8%,生物气组分H_2+CO含量高达67%,热解产物具有良好的工业利用价值。污泥热解生物气中H2S浓度超标10倍以上,而NH_3浓度未超标,硫化氢的去除技术研究值得关注。     

城市干污泥热解气化

针对包头市南郊污水处理厂污水污泥,采用先热解后对热解残渣进行气化的方法探讨城市污泥的有效利用方式。污泥热解实验取升温速率(20~60℃·min-1)和终温(400~600℃)作为影响因素,得出各热解产物产率的变化规律。结果表明,污泥热解在终温为600℃时失重率达到57.53%,焦油产率在450℃达到峰值。污泥残渣的气化分别以水蒸气和CO2作为气化剂,探讨了800~1 000℃范围内的气化产品气组分变化规律。以水蒸气为气化剂时,污泥热解残渣的可制备富氢产品气,产品气中H2体积分数随着反应温度的增加而增加,1 000℃时H2含量可达68.83%,H2+CO含量达到81.36%,低位热值为9.18 MJ·Nm-3。以CO2作为气化剂时,产品气中富含CO,温度越高CO含量越高,1 000℃时到达最大值53.84%,产品气低位热值为7.25 MJ·Nm-3。     

炼焦煤尾煤催化热解制取富氢燃料气

以炼焦煤原煤、尾煤为研究对象，采用微量热重、常量固定床实验装置对其在热解过程中的质量变化和气相产物进行了对比分析。考察了温度、6种催化剂（CaO、MgO、Fe、Ni、NaOH、A1）及其添加比例对炼焦煤尾煤热解制取富氢燃料气的影响。结果表明，尾煤中富集的无机矿物质对热解制取富氢燃料气有促进作用，单位尾煤热解H2产率要比原煤高出1．93％。温度是影响尾煤热解产气的重要参数，热解终温的上升有利于H2产量的提高，随终温800℃升高到950℃H，产量增长了32．59mL／g。在催化热解实验中，除Al和MgO对尾煤热解有抑制作用外，CaO、Fe、Ni及NaOH均对尾煤热解产H2有促进作用，以CaO和Fe效果最为明显。并且不同添加比例的CaO和Fe对热解制取富氢燃料有一定的影响。     

润滑油废白土的热解处理

以润滑油废白土为原料,利用电热解法,研究了热解终温、加热速率和CaO添加量对热解产物的影响。实验结果表明:热解终温对热解产物的影响最为显著。随着热解终温的升高,不凝气产量和产油率均迅速增加。当热解终温达到600℃时,其增加的速率逐渐缓慢增大。当控制热解终温为800℃、加热速率为16℃/min、CaO添加量为0.5%时,富氢气体产量为189.2 L/kg,气体中主要成分为H2和CH4,其含量分别为27.97%和41.64%;热解残渣含油率和重金属溶出物均低于标准规定值,热解油产率为10.98%,回收率为38.94%,其主要成分为汽油、柴油和重油3部分组成,分别含19.13%、31.35%和49.52%。     

含油污泥微波热解工艺条件优化现场实验研究

采用自主设计的30 kW大功率微波设备开展了含油污泥微波热解的现场实验,考察了吸波剂种类和添加量、热解终温、微波辐照时间、污泥处理量等对微波热解处理效果的影响.结果表明,污泥热解残渣可以作为吸波剂提高含油污泥的微波热解处理效果,综合考虑热解效果和成本,其较佳的添加量为5％(质量分数),此时污泥的除油率可达99.84％；随着热解终温的升高,污泥的除油率逐渐升高,当热解终温达到500℃时,处理后污泥的含油率降为0.200％(质量分数,下同),满足《农用污泥中污染物控制标准》(GB 4284-84)的限值标准(石油类限值为0.3％(质量分数))；微波辐照时间对含油污泥的热解效果影响较显著,当微波辐照时间达到180 min时,处理后污泥含油率仅为0.230％；含油污泥处理量低于20 kg/次时,单位质量含油污泥完成热解消耗的电量随着处理量的增加而减少,而超过20 kg/次时,耗电量随着处理量的增加而增加,因此本实验所用设备较经济的含油污泥处理量为20 kg/次.     

催化剂掺混对污泥快速热解产气的影响

将干污泥(DS)与3种催化体系(CaO、焦炭、CaO-焦炭)掺混,经机械化学预处理后制得热解混合样品,考察催化剂掺混对DS快速热解产气的影响。研究表明,CaO可以提高DS热解综合产气效果,促进热解气相产物中的CH4和CO2向H2和CO转化,当CaO和DS质量比为1.00∶1.00时,热解气相产物中H2、CO体积分数之和、气体产率、产气低位热值及H2产量均达到最大值,分别为77.04%、0.412 m3/kg、62.75kJ/kg和6.88 mol/kg;焦炭可以改善DS热解气相产物品质,当焦炭和DS质量比为1.00∶1.00时,热解气相产物中H2体积分数和氢占比(H2与CO的体积比)最优,分别为38.90%和1.23;CaO-焦炭体系可以明显提高DS热解液相产物质量分数,当CaO、焦炭和DS质量比为0.50∶0.50∶1.00时,热解液相产物的质量分数达到最大值50.17%。研究结果为剩余污泥的资源化利用提供数据支持。     

城市有机垃圾热解过程中NH_3、H_2S和HCl的析出特性

为了对城市有机垃圾热解过程中NH_3、H_2S和HCl的析出特性进行研究,采用箱式气氛炉在500~800℃热解终温下进行热解实验。热解过程中产生的NH3、H2S和HCl分别用硼酸溶液、乙酸锌-乙酸钠溶液以及Na OH溶液吸收,并分别采用分光光度法和滴定法进行量化。实验结果表明:NH3-N、H2S-S和HCl-Cl的析出率随着温度的升高而增加,热解终温为500、600、700和800℃时,NH3-N的析出率分别为39%、40%、30%和44%,H_2S-S的析出率分别为18%、22%、25%和26%,HCl-Cl的析出率分别为68%、71%、76%和85%;热解终温控制在700℃有利于减少NH3-N的析出,低温热解(500℃)有利于减少H2S和HCl的析出;热解炭中S和Cl的残留率随着热解终温的升高而降低,终温800℃时的残留率分别为41%和5%。     

生物质催化气化制取富氢燃气的研究

以流化床为反应器 ,探讨了一些主要参数如 :反应器温度 ,水蒸气 ,当量比ER以及催化剂对气体成分、氢产率和潜在氢产率的影响。实验所用催化剂为白云石和镍基催化剂。在实验条件范围内 ,氢产率为 2 2— 83g/kg生物质 (湿基 ) ,潜在氢产率为 115— 2 2 3g/kg生物质 (湿基 )。结果表明 ,较高的反应器温度 ,适当的水蒸气添加量可以有效提高氢的产出 ;白云石和镍基催化剂可使产品气中的氢含量提高 10 %以上。     

热解条件对硫酸钙/污泥基生物炭中Pb、Ni形态分布及生态风险的影响

以污泥为原料,硫酸钙为添加剂,采用热解法制备了硫酸钙/污泥基生物炭,考察了硫酸钙添加量、热解温度、升温速率及保温时间对生物炭中Pb、Ni形态分布的影响,并利用生态风险评价指数(RAC)对优化热解条件下制备的硫酸钙/污泥基生物炭中的Pb、Ni进行了生态风险评价。结果显示,优化热解条件为:硫酸钙添加量2.5%(质量分数)、热解温度750℃、升温速率2℃/min、保温时间15min。该优化热解条件下制备的硫酸钙/污泥基生物炭中的重金属Pb、Ni的生态风险分别为无风险、低风险,相对于污泥(低风险、中等风险)明显降低。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.