La2O3/ZnO/TiO2光催化降解活性艳红K-2BP的研究

采用溶胶-凝胶法制备了La2O3/ZnO/TiO2复合光催化剂,以紫外灯为光源,活性艳红K-2BP为模型降解物,研究了La2O3/ZnO/TiO2的光催化性能.结果表明:当锌和镧的掺杂量w(zno)=20%,w(La2O3)=0.5%,煅烧温度为500℃时,La2O3/ZnO/TiO2复合光催化剂的光催化活件最高;当催化荆投加量4 g/L,通气量800 mL/min,初始pH值3.12时,La2O3/ZnO/TiO2对活性艳红K-2BP的降解效果最好.实验证明.La2O3/ZnO/TiO2对活性艳红K-2BP的降解遵从Lang-muir-Hinshelwood动力学模型,测得其反应速率常数k=11.5 mg/(L·min);吸附常数K=2.88×10-2L/mg.     

水溶液中活性艳红KE-3B的臭氧超声联合脱除

采用臭氧/超声联合技术去除模拟废水中的活性艳红KE-3B。臭氧/超声处理前后KE-3B的紫外可见吸收谱没有明显的变化。臭氧/超声联合作用、单独臭氧化和单独超声处理脱除活性艳红KE-3B模拟废水5 min后的去除率分别为97%、73%和5%，表明臭氧/超声联合降解活性染料具有更高的氧化速率。实验研究了pH值、臭氧投加量、超声能量密度、反应温度对超声/臭氧降解活性艳红KE-3B反应速率的影响，在实验研究范围内，随着溶液初始pH的增大，KE-3B的去除率先增大后减小，超声能量密度的改变对KE-3B的去除影响不大，温度升高有利于氧化反应的进行。在溶液初始pH值为9.0，臭氧投加量3.2 g/h，超声能量密度176 W/L，反应温度20℃时，浓度为100 mg/L的活性艳红KE-3B溶液的去除率最高。     

天然沸石负载La2O3-ZnO-TiO2光催化降解活性艳红K-2BP

利用80目天然斜发沸石作载体制备La2O3(0.5%)-ZnO(20%)-TiO2/沸石复合光催化剂,以20 W紫外灯为光源,在自制的光催化反应器中降解活性艳红K-2BP,考察了光照时问、空气通入量、催化剂用最、溶液初始浓度、H2O2与Fe3 投加量等对活性艳红K-2BP光催化降解率的影响.结果表明,当溶液初始浓度为60 mg/L,催化剂投加量为12 g/L,通气量为1 200 mL/min,光照2.5 h,活性艳红K-2BP的降解率可达99.2%;H2O2和Fe3投加量为4 mL/L和3 g/L时,光照1 h活性艳红K-2BP降解率分别为100%和97.2%.紫外-可见吸收光谱显示,LZTZ光催化剂町有效降解印染废水.     

光催化臭氧氧化法在废水处理中的研究进展

光催化臭氧氧化法作为一种有效的废水处理技术,对难降解的有机废水,具有良好的降解功效。文中分析了UV/O3/Fe2＋、UV/O3/Fe3＋和UV/O3/H2O2体系的反应机理,介绍了光催化臭氧氧化法在废水处理中的应用情况,指出了光催化臭氧氧化法存在的问题和展望。     

涡流空化/Fenton协同降解溶液中活性艳红K-2BP

采用涡流空化(SC)/Fenton协同降解溶液中活性艳红K-2BP,探讨了H2O2、Fe2+、pH、涡流压力以及活性艳红K-2BP初始浓度对SC/Fenton降解效果的影响。结果表明,H2O2和Fe2+的浓度过高或过低都会降低活性艳红K-2BP的降解率,低pH环境有助于活性艳红K-2BP的降解,活性艳红K-2BP的降解率随涡流压力的增大而升高,随其初始浓度的增加而降低。当活性艳红K-2BP初始质量浓度为10mg/L,H2O2质量浓度为165mg/L,Fe2+摩尔浓度为1.5×10-4mol/L,pH为4.0,涡流压力为0.8MPa时,活性艳红K-2BP降解率可达91.81%。     

臭氧/双氧水/紫外光联用降解饮用水中溴氯乙腈的试验研究

为减少饮用水氯化消毒过程中产生的含氮消毒副产物溴氯乙腈(BCAN),降低其潜在的致癌风险,分别采用臭氧(O3)、双氧水(H2O2)和紫外光(UV)及其联合工艺,考察了不同试验条件下BCAN的降解效果及影响因素,并探讨了其降解机制和动力学规律。结果表明,O3、H2O2和UV工艺对BCAN降解效果都不理想,UV/H2O2和UV/H2O2/O3联合工艺可以较有效地降解水中的BCAN。在BCAN初始质量浓度为20μg/L、紫外光强为31μW/cm2、H2O2质量浓度为40 mg/L、O3质量浓度为7.9mg/L条件下,反应进行120min后,UV/H2O2联合工艺与UV/H2O2/O3联合工艺对BCAN的降解率分别为77.50%、94.05%。UV/H2O2/O3联合工艺对BCAN的降解效果比UV/H2O2联合工艺更好,UV/H2O2和UV/H2O2/O3联合工艺降解BCAN均符合一级反应动力学规律。     

O3/H2O2高级氧化技术H2O2加入量的简易控制方法

对与臭氧有着不同反应活性的3类有机污染物,探讨并建立了O3/H2O2高级氧化技术H2O2较优投加量的简易控制方法.结果表明,水中存在溶解臭氧是H2O2与臭氧降解效率具有协同作用的必要条件,另外,H2O2的较优加入量直接依赖于目标有机污染物与臭氧的反应活性.对于不同的有机物及在常规的臭氧化水处理时间内,H2O2加入量控制在单独臭氧化处理时水中溶解臭氧的20～30倍(质量比)之间为宜.这种简易控制H2O2加入量的方法对推广O3/H2O2技术在实际废水处理中的应用具有重要的意义.     

低强度紫外线催化降解活性艳红X-3B溶液研究

研究了低强度紫外线对活性艳红X 3B溶液的处理效果 ,考察了紫外线波长、溶液pH、起始浓度、催化剂用量、温度及曝气条件对染料降解的影响。结果表明 ,36 5nm紫外线 (UV3 65nm)的处理效果明显优于 2 5 4nm紫外线 (UV2 54nm) ,反应最适pH为 3 0～ 5 0 ,最佳TiO2 投加量为 2 0g/L ,最适温度为 4 0℃ ,通入空气或氧气均能加速活性艳红X 3B的降解。在上述条件下 ,起始浓度为 5 0mg/L的活性艳红X 3B在 1 5 0min内可完全分解     

臭氧/紫外联合降解甲醛的试验研究

在臭氧单独作用、紫外光单独作用和UV/O₃ 3种条件下分别对甲醛进行降解试验，研究表明,臭氧和紫外在降解甲醛的试验中存在明显的协同促进作用。单独臭氧对甲醛降解效果并不显著。紫外单独作用时，对甲醛几乎没有降解作用。在UV/O₃条件下，甲醛的降解率大大提高，特别是在高浓度臭氧条件下，降解率高达63％。臭氧浓度增大，降解率增大；紫外光强度增大，降解效果提高；气体流量增大，降解率下降；湿度增大，降解率提高。对甲醛降解试验进行动力学研究，结果表明，光照强度和臭氧浓度增大，一级反应速率增大，提高臭氧浓度要比加强紫外强度更能促进甲醛的降解。     

紫外光助O3、H2O2氧化降解炼油废碱水的可行性实验

炼油高浓度有机废碱水是石化行业中很难降解的废水.本实验用光化学氧化技术对其进行了降解研究,比较了紫外光/空气、紫外光/O3、紫外光/空气/H2O2系统的处理效果.结果表明,光化学氧化技术降解此废水是可行的,紫外光可使废水中COD、油、酚的降解率明显提高.当废水中O3的投加量每小时为22 mg/L,或H2O2投加量为1%/L时,UV/O3法与UV/空气/H2O2法的降解效果相近.同时,通过控制O3浓度或H2O2的投加量等条件,可使废水中COD、油、酚和硫化物降解到地方污染物二级排放标准.     

Advanced oxidation of a pulp mill bleaching wastewater.

The degradation, by several advanced oxidation reactions, of a pulp mill ECF bleaching effluent, was studied. The initial biodegradability of the organic matter present in the effluent, estimated as the BOD5/COD, was low (0.3). When the effluent was submitted to ozonation and to five different advanced oxidation systems (O3/UV, O3/UV/ZnO, O3/UV/TiO2, O2/UV/ZnO, O2/UV/TiO2), the biodegradability increase significantly. After five minutes of reaction, the O3/UV system appears as the most efficient in to transform the organic matter to more biodegradable forms. A similar effect was observed when the effluent was submitted to an activated sludge treatment. The COD, TOC and toxicity reduction correlated well with the biodegradability enhancement after AOPs treatments.     

活性炭纤维上4-氯酚及焦化废水尾水的O3催化氧化降解实验研究

选择YT-1000型活性炭纤维（ACF）作为催化剂，考察ACF与O₃协同作用催化降解水溶液中4-氯酚的最佳反应条件，并将该条件应用于焦化废水生物处理尾水中难降解有机污染物的催化氧化。ACF表面具有丰富的微孔结构，对4-氯酚有良好的吸附作用，在动力学上提高了其与O3反应的起始浓度，并且在ACF表面含氧、含氮等基团的催化作用下发生氧化反应，1 L浓度为100 mg/L的4-氯酚水样中投加2 g ACF反应6 min时，吸附作用对TOC的去除率为43.4%，而ACF协同O₃作用时的TOC去除率提高到72.5%，协同增效作用为67.1%；在选定的反应条件下，ACF协同O₃降解焦化废水生物处理尾水，60 min时的TOC与色度的去除率分别达到56.8%和96.3%。上述研究过程证明了吸附作用与催化作用的协同能有效降解生物过程不能降解的焦化废水中惰性有机污染物。     

Catalytic activity of Ru/Al2O3 for ozonation of dimethyl phthalate in aqueous solution

With dimethyl phthalate as the model pollutant and Ru/Al(2)O(3) as catalyst, this paper systemically investigates the removal of total organic carbon (TOC) of system. Our results have confirmed that Ru/Al(2)O(3) can significantly increase the effect of ozonation. TOC removal in 120 min can reach 72% while only 24% with ozone alone. The optimal catalyst preparing condition was 0.1 wt% Ru content, 600 degrees C calcination temperature, 0.5-1.0mm particle diameter, which is characterized by a high surface area and a large population of surface active sites. The contrasting experiments of ozone alone, catalyst adsorption after ozonation, and catalytic ozonation confirmed that catalytic reaction was the most important process to TOC removal in system with Ru/Al(2)O(3) as catalyst.     

A comparative study of the removal of 3-indolebutyric acid using advanced oxidation processes

In this study, advanced oxidation technologies, namely Fenton Process (FP), Fenton-Like Process (FLP), ozonation (O3) and O3/H2O2 processes, were applied to synthetic wastewater containing 3-indolebutyric acid (IBA). The effectiveness of each process was investigated at different pH values, Fe(+2), Fe(+3), O3 and H2O2 concentrations with respect to the removal efficiencies for chemical oxygen demand (COD) and total organic carbon (TOC). The best removal efficiencies were seen at pH 3 and 2 mM Fe concentration in both FP and FLP, in which the optimum H2O2 concentrations were 6 mM for FP and 10 mM for FLP. Optimum process conditions were pH 12 for the O3 process, pH 9 for the O3/H2O2 process and 1:1 O3/H2O2 molar ratio. The highest COD removal efficiency was 86 percent, obtained in the O3/H2O2 process and the highest TOC removal efficiency was obtained at 77 percent in the FP.     

改性TiO2/浮石光催化去除二级出水中有机物

为了实现城市污水厂二级出水的回用,将La3+、Fe3+共掺杂TiO2/浮石光催化用于二级出水中有机物的去除。在优化工艺条件下,该方法对TOC的去除率为49.0%,对UV254的去除率为76.5%;出水BDOC/DOC值大幅度提高,由最初的0.21提高到0.56,增加了出水的可生化性;二级出水中存在着影响光催化去除有机物的因素,其中阴离子对有机物的去除有一定的抑制作用;光催化反应在通过O3强化后对有机物的去除率得到提高,TOC的去除率达到75.0%,光催化和O3氧化对有机物的去除具有协同效应;随着光催化反应次数的增加,催化剂活性有下降趋势,使用10次后TOC去除率下降到第一次使用时的16.7%,再生能够使催化活性恢复到使用前的95%,催化剂在使用15次以内稳定性较好。     

Comparison of the degradation of p-hydroxybenzoic acid in aqueous solution by several oxidation processes

A comparative study is made of 12 methods of chemical oxidation applied to degrading p-hydroxybenzoic acid in aqueous solution. The oxidation processes tested were: UV, O3, UV/TiO2, O3/Fe2+, O3/H2O2, O3/UV, UV/H2O2, H2O2/Fe2+, H2O2/Fe2+/O3, UV/H2O2/O3, H2O2/Fe2+/UV and O3/UV/H2O2/Fe2+. The 12 processes were ranked by reactivity. In a kinetic study, the overall kinetic rate constant was split up into three components: direct oxidation by UV irradiation (photolysis), direct oxidation by ozone (ozonation), and oxidation by free radicals (mainly OH*).     

Mineralization of C.I. Reactive Yellow 84 in aqueous solution by sonolytic ozonation

The operational parameters and mechanism of mineralization of C.I. Reactive Yellow 84 (RY84), one of the azo dyes, in aqueous solution were investigated using sonolytic ozonation (US/O(3) oxidation). Of the pseudo-first-order degradation rate constants of TOC reduction, 9.0 x 10(-4), 7.3 x 10(-3) and 1.8 x 10(-2)min(-1) were observed with US, O3, and a combination of US and O3, respectively. These results illustrate that ozonation combined with sonolysis for removal of TOC is more efficient than ozonation alone or ultrasonic irradiation alone without considering the operating costs. With the initial pH value at 10.0, the ozone dose at 4.5 g h(-1), the energy density of ultrasound at 176 W l(-1), and the initial concentration of RY84 at 100 mg l(-1), the extent of mineralization measured as TOC loss was maximized. The variation of the concentrations of related ions (oxalate, formate, acetate, NO3(-), NO2(-), NH4(+), Cl(-), and SO4(2-)) during the reaction process was monitored. Other organic intermediates detected by GC/MS were N-methyleneaniline, phthalic acid, 4-hydroxyphthalic acid, isocyanatobenzene, aniline, 4-iminocyclohexa-2,5-dien-1-one, butene diacid and urea. Based on these findings, a tentative degradation pathway was proposed.     

Atrazine removal by ozonation processes in surface waters

Atrazine (6-chloro-N-ethyl-N'-isopropyl-1,3,5-triazinedyl-2,4-diamine) was treated with ozone alone and in combination with hydrogen peroxide or UV radiation in three surface waters. Experiments were carried out in two bubble reactors operated continuously. Variables investigated were the ozone partial pressure, temperature, pH, mass flow ratio of oxidants fed: hydrogen peroxide and ozone and the type of oxidation including UV radiation alone. Residence time for the aqueous phase was kept at 10 min. Concentrations of some intermediates, including deethylatrazine, deisopropylatrazine and deethyldeisopropylatrazine, were also followed. The nature of water, specifically the alkalinity and pH were found to be important variables that affected atrazine (ATZ) removal. Surface waters with low alkalinity and high pH allowed the highest removal of ATZ to be reached. There was an optimum hydrogen peroxide to ozone mass flow ratio that resulted in the highest ATZ removal in each surface water treated. This optimum was above the theoretical stoichiometry of the process. Therefore, to reach the maximum removal of ATZ in a O3/H2O2 process, more hydrogen peroxide was needed in the surface waters treated than in ultrapure water under similar experimental conditions. In some cases, UV radiation alone resulted in the removal of ATZ higher than ozonation alone. This was likely due to the alkalinity of the surface water. Ozonation and UV radiation processes yield different amounts of hydrogen peroxide. Combined ozonations (O3/H2O2 and O3/UV) lead to ATZ removals higher than single ozonation or UV radiation but the formation of intermediates was higher.     

Photocatalytic oxidation of pesticide rinsate

Pesticide rinsate has been considered as one of the major threats for the environment. In this study, photocatalysts such as TiO2 and O3 were used to promote the efficiency of direct UV photolysis to prevent such wastewater pollution. Carbofuran (a carbamate pesticide) and mevinphos (an organophosphate pesticide) with a concentration of 100 mg/L were selected as the test pesticide rinsates. Parent pesticide compound, COD, and microtoxicity analysis were employed to investigate the effect of photocatalyst on the degradation efficiency of pesticide in rinsate. It was found that the photocatalytic oxidation process (UV/O3, UV/TiO2) showed much higher COD removal and microtoxicity reduction efficiency for pesticide rinsate than did direct UV photolysis under the imposed conditions, suggesting that photocatalytic oxidation processes such as UV/O3 and UV/TiO2 could be a better alternative to treat pesticide rinsate. In addition, it was noted that increasing the initial pH of mevinphos rinsate to a basic level was required to reach higher COD removal efficiency and positive microtoxicity reduction efficiency while it was not necessary for the treatment of carbofuran rinsate.     

Degradation of dyes in aqueous solutions by the Fenton process

Degradation of 20 different dyes in aqueous solutions by the Fenton process was performed. These dyes include 6 types: acidic, reactive, direct, cationic, disperse and vat dyes. The former four types of dyes were decolorized and their TOC values were decreased greatly, while the color and TOC removals of the latter two types were lower. The catalytic activities of four metal ions on the degradation efficiencies of Vat Blue BO, which was chosen as a model dye because of its lowest color and TOC removals, were compared in the dark and under the ultraviolet light irradiation. The catalytic ability of different metals was Fe2+>Cu2+>Mn2+>Ag+ in the dark, and the same sequence was obtained under irradiation condition with greater degradation efficiency. Furthermore, the efficiencies of three oxidation processes, including H2O2/UV, Fe2+/H2O2 and Fe2+/H2O2/UV were compared. The results showed that the oxidation by Fe2+/H2O2/UV was the strongest, and even greater than the arithmetic sum of the other two processes, which suggests the synergistic effect of ultraviolet and ferrous ions on the degradation reaction.