The effect of variable sub-grid deposition factors on the results of the lagrangian long-range transport model of EMEP

The EMEP/MSC-W routine model for long-range atmospheric transport of sulphur and nitrogen includes a correction for the unresolved sub-grid-scale deposition in emission grid-squares. A constant fraction of the emissions is assumed to be directly deposited inside the first grid-square. Experiments have been performed to estimate the effects of using factors which vary with emission height and meteorological conditions. Results indicate that the constant local deposition factor used for sulphur dioxide in the routine model, is an overestimate, in particular for high-level emission sources. The change in annual deposition caused by the new local deposition factor for sulphur dioxide, is most clearly seen as a decreased deposition in the grid-squares with the largest emissions such as due for the former German Democratic Republic. The amount of this decrease strongly depends on the source height distribution. With the presently available emission data, a decrease of maximum 36% can be expected in individual grid squares. In grid-squares dominated by transboundary deposition, the increase is typically lower than 10%.     

Urban emissions measured with aircraft

Detailed knowledge of the quantity and composition of urban emissions is a prerequisite for successful application of atmospheric models to predict transport and distribution of primary and secondary air pollutants in the troposphere. We investigate the prospects and limitations of aircraft measurements in the determination of emission fluxes from urban areas. Our analysis focuses on data collected in September 1994 in and around Athens, Greece. Generally, emission fluxes from cities can be quantified with aircraft and with the minimum acceptable precision (uncertainty better than a factor of 2) only under very favorable meteorological conditions, namely in a homogeneous flow field in a well-mixed boundary layer. Better accuracy can be achieved only through ensemble averaging of repeated measurements. From our measurements in the Athens area, we deduced relative emission ratios of pollutant gases. With the support of ground-based measurements in a street canyon, the emission ratios NOx/CO, SO2/CO, and volatile organic compounds/CO (34 individual VOCs) could be determined with high precision. These results are very useful in analyzing differences between various existing emission inventories. Our data for VOCs reveal that the non-traffic emissions are of the same magnitude as the emissions originating from traffic.     

Estimates of emissions of SO2, NOx, HCl and NH3 from a densely populated region of the UK

Estimates of emissions of SO2, NOx, HCl and NH3 have been made for a densely populated region of the UK, the North-West of England, using data on power generation, incinerator plant capacity, fuel usage and animal and human population statistics. The spatial distributions of SO2 and NOx emissions are quite different, reflecting their different source strengths. The emissions from motor vehicles make up 52% of the NOx emissions from the North-West of England, whilst those from fossil-fuel-fired power stations make up 20%. The emissions of fossil-fuel-fired power stations make up 58% of SO2 emissions from the North-West. A large fossil-fuel-fired power station is the largest known point source for emissions of SO2, NOx and HCl. The largest contribution to NH3 emissions in the North-West is from cattle. Humans may contribute some NH3 to overall emissions but there is considerable uncertainty as to how much is emitted and what fraction of this is deposited within buildings. The uncertainties in the methodologies used are high-lighted and, where possible, recommendations are made as to how future emissions estimates might be improved. Potential reductions in emissions of SO2, NOx and HCl are discussed under basic scenarios of planned power station closures in the area and the compliance of the electricity generation industry with the European Community Directive on Large Combustion Plants.     

Measurements of nitrogen dioxide concentrations at rural sites in the United Kingdom using diffusion tubes

Nitrogen dioxide concentrations have been measured at rural sites in the United Kingdom and have revealed a marked spatial variation. The annual mean NO2 concentration varies from approximately 1 microg Nm-3 in Northern Ireland to approximately 7 microg Nm-3 in East Anglia. Though the temporal resolution of the diffusion tube method is limited by exposure periods of 2-4 weeks, it was possible to detect a marked seasonal variation in NO2 concentration at all sites, with higher values in the winter than in the summer. This is in contrast to the small seasonal variation previously observed at sites in London. Sulphur dioxide concentrations were measured daily using a bubbler method and, if expressed in terms of mass of sulphur and nitrogen, the SO2 and NO2 annual mean concentrations were similar. This is in contrast to an S/N ratio of greater than 3 in total UK emissions of SO2 and NOx. It seems likely that this difference is due to a combination of the different spatial distributions and heights of emissions of SO2 and NOx, the influence of local sources of NOx, and the smaller S/N ratio in Continental European emissions.     

Regional NOx emission inversion through a four-dimensional variational approach using SCIAMACHY tropospheric NO2 column observations

In this paper, the NOx emission scaling factors applied over the 2001 National Emissions Inventory (NEI) are estimated through a four-dimensional variational (4D-Var) approach using SCIAMACHY (Scanning Imaging Absorption spectroMeter for Atmospheric CHartographY) tropospheric NO₂ columns measured during summer 2004. In the “top-down” approach, two-month average NO₂ columns are assimilated into a regional chemical transport model (CTM), STEM, using different assimilation setups. In a basic setup, NOx emissions are adjusted by assimilating the NO₂ columns. A more general setup of emission inversion allows the initial O₃ concentrations be adjusted along with the NOx emissions. A final case is set up to assimilate both the NO₂ columns and O₃ measurement from various platforms while allowing adjustments of both the NOx emissions and the initial O₃ concentrations. It is found that the addition of O₃ measurements did not improve the NOx emission inversion. With the NOx emission at surface and upper levels being adjusted separately, results from four cases show that the elevated NOx emission reduction ranges from 8.9% to 11.4%, and the surface NOx emission reduction is up to 6.6%. All the cases show NOx emission reduction in Ohio valley and Washington, District of Columbia areas.     

Methodologies for estimating disaggregated anthropogenic emissions--application to a coastal Mediterranean region of Spain

Regional estimates of both anthropogenic and biogenic emissions are important inputs for models of atmospheric chemistry. A disaggregated emissions inventory of all relevant pollutants for an area of 100 x 100 km2 centered in Burriana (Castellon, Spain) has been worked out. Time and spatial resolutions were hourly and 1 x 1 km2, respectively. Estimates were made for all relevant sources of anthropogenic emissions. The pollutants considered were SO2, NOx, NMVOCs (nonmethane volatile organic compounds), CH4, CO, CO2, N2O, and NH3. Thus, the emissions inventory includes up to 18 different NMVOCs. Emissions were computed for a typical sunny workday in June when strong photochemical activity could be expected. A "top-down" methodology was applied, taking as a starting point official annual and provincial estimates based on CORINAIR emission factors. This procedure is a very useful tool, particularly for those cases where a lack of sufficient local detailed information about the main emission-generating activities, such as road traffic, makes the use of a "bottom-up" approximation inadvisable. Moreover, updating these emission inventories is easier and they could be used to evaluate the impact of possible abatement strategies.     

Idle emissions from heavy-duty diesel and natural gas vehicles at high altitude

Idle emissions of total hydrocarbon (THC), CO, NOx, and particulate matter (PM) were measured from 24 heavy-duty diesel-fueled (12 trucks and 12 buses) and 4 heavy-duty compressed natural gas (CNG)-fueled vehicles. The volatile organic fraction (VOF) of PM and aldehyde emissions were also measured for many of the diesel vehicles. Experiments were conducted at 1609 m above sea level using a full exhaust flow dilution tunnel method identical to that used for heavy-duty engine Federal Test Procedure (FTP) testing. Diesel trucks averaged 0.170 g/min THC, 1.183 g/min CO, 1.416 g/min NOx, and 0.030 g/min PM. Diesel buses averaged 0.137 g/min THC, 1.326 g/min CO, 2.015 g/min NOx, and 0.048 g/min PM. Results are compared to idle emission factors from the MOBILE5 and PART5 inventory models. The models significantly (45-75%) overestimate emissions of THC and CO in comparison with results measured from the fleet of vehicles examined in this study. Measured NOx emissions were significantly higher (30-100%) than model predictions. For the pre-1999 (pre-consent decree) truck engines examined in this study, idle NOx emissions increased with model year with a linear fit (r2 = 0.6). PART5 nationwide fleet average emissions are within 1 order of magnitude of emissions for the group of vehicles tested in this study. Aldehyde emissions for bus idling averaged 6 mg/min. The VOF averaged 19% of total PM for buses and 49% for trucks. CNG vehicle idle emissions averaged 1.435 g/min for THC, 1.119 g/min for CO, 0.267 g/min for NOx, and 0.003 g/min for PM. The g/min PM emissions are only a small fraction of g/min PM emissions during vehicle driving. However, idle emissions of NOx, CO, and THC are significant in comparison with driving emissions.     

Effectiveness of emission control technologies for auxiliary engines on ocean-going vessels

Large auxiliary engines operated on ocean-going vessels in transit and at berth impact the air quality of populated areas near ports. This paper presents new information on the comparison of emission ranges from three similar engines and the effectiveness of three control technologies: switching to cleaner burning fuels, operating in the low oxides of nitrogen (NOx) mode, and selective catalytic reduction (SCR). In-use measurements of gaseous (NOx, carbon monoxide [CO], carbon dioxide [CO2]) and fine particulate matter (PM2.5; total and speciated) emissions were made on three auxiliary engines on post-PanaMax class container vessels following the International Organization for Standardization-8178-1 protocol. The in-use NOx emissions for the MAN B&W 7L32/40 engine family vary from 15 to 21.1 g/kW-hr for heavy fuel oil and 8.9 to 19.6 g/kW-hr for marine distillate oil. Use of cleaner burning fuels resulted in NOx reductions ranging from 7 to 41% across different engines and a PM2.5 reduction of up to 83%. The NOx reductions are a consequence of fuel nitrogen content and engine operation; the PM2.5 reduction is attributed to the large reductions in the hydrated sulfate and organic carbon (OC) fractions. As expected, operating in the low-NOx mode reduced NOx emissions by approximately 32% and nearly doubled elemental carbon (EC) emissions. However, PM2.5 emission factors were nearly unchanged because the EC emission factor is only approximately 5% of the total PM2.5 mass. SCR reduced the NOx emission factor to less than 2.4 g/kW-hr, but it increased the PM2.5 emissions by a factor of 1.5-3.8. This increase was a direct consequence of the conversion of sulfur dioxide to sulfate emissions on the SCR catalyst. The EC and OC fractions of PM2.5 reduced across the SCR unit.     

On the local and regional influence on ground-level ozone concentrations in Hong Kong

Hong Kong is a densely populated city situated in the fast developing Pearl River Delta of southern China. In this study, the recent data on ozone (O3) and related air pollutants obtained at three sites in Hong Kong are analyzed to show the variations of O3 in urban, sub-urban and rural areas and the possible regional influences. Highest monthly averaged O3 was found at a northeastern rural site and lowest O3 level was observed at an urban site. The levels of NOx, CO, SO2 and PM10 showed a different spatial pattern with the highest level in the urban site and lowest at the rural site. Analysis of chemical species ratios such as SO2/NOx and CO/NOx indicated that the sites were under the influences of local and regional emissions to varying extents reflecting the characteristics of emission sources surround the respective sites. Seasonal pattern of O3 is examined. Low O3 level was found in summer and elevated levels occurred in autumn and spring. The latter appears different from the previous result obtained in 1996 indicating a single maximum occurring in autumn. Principal component analysis was used to further elucidate the relationships of air pollutants at each site. As expected, the O3 variation in the northeastern rural area was largely determined by regional chemical and transport processes, while the O3 variability at the southwestern suburban and urban sites were more influenced by local emissions. Despite the large difference in O3 levels across the sites, total potential ozone (O3+NO2) showed little variability. Cases of high O3 episodes were presented and elevated O3 levels were formed under the influence of tropical cyclone bringing in conditions of intense sunlight, high temperature and light winds. Elevated O3 levels were also found to correlate with enhanced ratio of SO2 to NOx, suggesting influence of regional emissions from the adjacent Pearl River Delta region.     

The relationship between atmospheric pollutant emissions and fuel qualities of inland vessels in Jiangsu Province,China

Air pollution caused by ship exhaust emission is receiving more and more attention. The physical and chemical properties of fuels, such as sulfur content and PAHs content, potentially had a significant influence on air pollutant emissions from inland vessels. In order to investigate the effects of fuel qualities on atmospheric pollutant emissions systematically, a series of experiments was conducted based on the method of actual ship testing. As a result, SO2, PM and NOx emission rates all increased with the increase of main engine rotating speed under cruise mode, while PM and NOx emission factors were inversely proportional to the main engine rotating speed. Moreover, SO2 emission factor changed little with the increase of the main engine rotating speed. In summary, the fuel-dependent specific emission of SO2 was a direct reflection of the sulfur content in fuel. The PM emission increased with the increase of sulfur content and PAHs content in fuel. However, fuel qualities impacted little on NOx emissions from inland vessels because of NOx formation mechanisms and conditions.

Implications: Ship activity is considered to be the third largest source of air pollution in China. In particular, air pollutants emitted from ships in river ports and waterways have a direct impact on regional air quality and pose threat on the health of local residents owing to high pollutants concentration and poor air diffusion. The study on the relationship between air pollutant emissions and fuel quality of inland vessels can provide foundational data for local authority to formulate reasonable and appropriate policies for reducing atmospheric pollution due to inland vessels.     

The contribution from shipping emissions to air quality and acid deposition in Europe

A global three-dimensional Lagrangian chemistry-transport model STOCHEM is used to describe the European regional acid deposition and ozone air quality impacts along the Atlantic Ocean seaboard of Europe, from the SO2, NOx, VOCs and CO emissions from international shipping under conditions appropriate to the year 2000. Model-derived total sulfur deposition from international shipping reaches over 200 mg S m(-2) yr(-1) over the southwestern approaches to the British Isles and Brittany. The contribution from international shipping to surface ozone concentrations during the summertime, peaks at about 6 ppb over Ireland, Brittany and Portugal. Shipping emissions act as an external influence on acid deposition and ozone air quality within Europe and may require control actions in the future if strict deposition and air quality targets are to be met.     

Models to predict emissions of health-damaging pollutants and global warming contributions of residential fuel/stove combinations in China

Residential energy use in developing countries has traditionally been associated with combustion devices of poor energy efficiency, which have been shown to produce substantial health-damaging pollution, contributing significantly to the global burden of disease, and greenhouse gas (GHG) emissions. Precision of these estimates in China has been hampered by limited data on stove use and fuel consumption in residences. In addition limited information is available on variability of emissions of pollutants from different stove/fuel combinations in typical use, as measurement of emission factors requires measurement of multiple chemical species in complex burn cycle tests. Such measurements are too costly and time consuming for application in conjunction with national surveys. Emissions of most of the major health-damaging pollutants (HDP) and many of the gases that contribute to GHG emissions from cooking stoves are the result of the significant portion of fuel carbon that is diverted to products of incomplete combustion (PIC) as a result of poor combustion efficiencies. The approximately linear increase in emissions of PIC with decreasing combustion efficiencies allows development of linear models to predict emissions of GHG and HDP intrinsically linked to CO2 and PIC production, and ultimately allows the prediction of global warming contributions from residential stove emissions. A comprehensive emissions database of three burn cycles of 23 typical fuel/stove combinations tested in a simulated village house in China has been used to develop models to predict emissions of HDP and global warming commitment (GWC) from cooking stoves in China, that rely on simple survey information on stove and fuel use that may be incorporated into national surveys. Stepwise regression models predicted 66% of the variance in global warming commitment (CO2, CO, CH4, NOx, TNMHC) per 1 MJ delivered energy due to emissions from these stoves if survey information on fuel type was available. Subsequently if stove type is known, stepwise regression models predicted 73% of the variance. Integrated assessment of policies to change stove or fuel type requires that implications for environmental impacts, energy efficiency, global warming and human exposures to HDP emissions can be evaluated. Frequently, this involves measurement of TSP or CO as the major HDPs. Incorporation of this information into models to predict GWC predicted 79% and 78% of the variance respectively. Clearly, however, the complexity of making multiple measurements in conjunction with a national survey would be both expensive and time consuming. Thus, models to predict HDP using simple survey information, and with measurement of either CO/CO2 or TSP/CO2 to predict emission factors for the other HDP have been derived. Stepwise regression models predicted 65% of the variance in emissions of total suspended particulate as grams of carbon (TSPC) per 1 MJ delivered if survey information on fuel and stove type was available and 74% if the CO/CO2 ratio was measured. Similarly stepwise regression models predicted 76% of the variance in COC emissions per MJ delivered with survey information on stove and fuel type and 85% if the TSPC/CO2 ratio was measured. Ultimately, with international agreements on emissions trading frameworks, similar models based on extensive databases of the fate of fuel carbon during combustion from representative household stoves would provide a mechanism for computing greenhouse credits in the residential sector as part of clean development mechanism frameworks and monitoring compliance to control regimes.     

Quantification of variability and uncertainty in lawn and garden equipment NOx and total hydrocarbon emission factors

Variability refers to real differences in emissions among multiple emission sources at any given time or over time for any individual emission source. Variability in emissions can be attributed to variation in fuel or feedstock composition, ambient temperature, design, maintenance, or operation. Uncertainty refers to lack of knowledge regarding the true value of emissions. Sources of uncertainty include small sample sizes, bias or imprecision in measurements, nonrepresentativeness, or lack of data. Quantitative methods for characterizing both variability and uncertainty are demonstrated and applied to case studies of emission factors for lawn and garden (L&G) equipment engines. Variability was quantified using empirical and parametric distributions. Bootstrap simulation was used to characterize confidence intervals for the fitted distributions. The 95% confidence intervals for the mean grams per brake horsepower/hour (g/hp-hr) emission factors for two-stroke engine total hydrocarbon (THC) and NOx emissions were from -30 to +41% and from -45 to +75%, respectively. The confidence intervals for four-stroke engines were from -33 to +46% for THCs and from -27 to +35% for NOx. These quantitative measures of uncertainty convey information regarding the quality of the emission factors and serve as a basis for calculation of uncertainty in emission inventories (EIs).     

Dynamic-chemical coupling of the upper troposphere and lower stratosphere region

The importance of the interaction between chemistry and dynamics in the upper troposphere and lower stratosphere for chemical species like ozone is investigated using two chemistry-climate models and a Lagrangian trajectory model. Air parcels from the upper troposphere, i.e. regions of lightning and aircraft emissions, are able to be transported into the lowermost stratosphere (LMS). Trajectory calculations suggest that the main transport pathway runs via the inter tropical convergence zone, across the tropical tropopause and then to higher latitudes, i.e. into the LMS. NOx from aircraft emissions at mid-latitudes are unlikely to perturb the LMS since they are washed-out while still in the troposphere. In contrast, NOx from tropical lightning has the chance to accumulate in the LMS. Because of the longer residence times of NOx in the LMS, compared to the upper troposphere, this excess NOx from lightning has the potential to form ozone in the LMS, which then is transported back to the troposphere at mid-latitudes. In the models, around 10% of the ozone concentration and 50% of the NOx concentration in the northern hemisphere LMS is produced by lightning NOx At least 5% of the ozone concentration and 35% the NOx concentration at 150 hPa at mid-latitudes originates from tropical lightning in the climate-chemistry simulations.     

Comparison of two photochemical modeling systems in a tropical urban area

Two photochemical smog modeling systems, UAM-V/ SAIMM (the Variable-Grid UAM/Systems Applications International Mesoscale Model) and CHIMERE/ECMWF (European Center for Medium Range Weather Forecast), are applied to the same tropical domain (Bangkok Metropolitan Region) and the same episode (January 13-14, 1997) to evaluate their relative performance using the same anthropogenic emission database (emission database available at the Pollution Control Department [PCD] 1997). Ozone (O3) produced by both models meets U.S. Environment Protection Agency (EPA) suggested prediction criteria of mean normalized bias error and mean normalized gross error on January 14 but none on January 13. Both models are tested with various modified databases of precursors emissions from the PCD original database. Performance of UAM-V is the best when using the modified emission data with volatile organic compound (VOC), NOx, and CO mobile source emission reduced by 50%, 50%, and 20% from the original database. CHIMERE suggests a similar emission database except for the VOC emission, which is a reduction by 40% from the original PCD mobile source emission. Spatial and temporal variations of O3, CO, NOy (total reactive nitrogen), and Ox (NO2+O3) predicted by both model systems using the modified     

Modeling and direct sensitivity analysis of biogenic emissions impacts on regional ozone formation in the Mexico-U.S. border area

A spatially and temporally resolved biogenic hydrocarbon and nitrogen oxides (NOx) emissions inventory has been developed for a region along the Mexico-U.S. border area. Average daily biogenic non-methane organic gases (NMOG) emissions for the 1700 x 1000 km2 domain were estimated at 23,800 metric tons/day (62% from Mexico and 38% from the United States), and biogenic NOx was estimated at 1230 metric tons/day (54% from Mexico and 46% from the United States) for the July 18-20, 1993, ozone episode. The biogenic NMOG represented 74% of the total NMOG emissions, and biogenic NOx was 14% of the total NOx. The CIT photochemical airshed model was used to assess how biogenic emissions impact air quality. Predicted ground-level ozone increased by 5-10 ppb in most rural areas, 10-20 ppb near urban centers, and 20-30 ppb immediately downwind of the urban centers compared to simulations in which only anthropogenic emissions were used. A sensitivity analysis of predicted ozone concentration to emissions was performed using the decoupled direct method for three dimensional air quality models (DDM-3D). The highest positive sensitivity of ground-level ozone concentration to biogenic volatile organic compound (VOC) emissions (i.e., increasing biogenic VOC emissions results in increasing ozone concentrations) was predicted to be in locations with high NOx levels, (i.e., the urban areas). One urban center--Houston--was predicted to have a slight negative sensitivity to biogenic NO emissions (i.e., increasing biogenic NO emissions results in decreasing local ozone concentrations). The highest sensitivities of ozone concentrations to on-road mobile source VOC emissions, all positive, were mainly in the urban areas. The highest sensitivities of ozone concentrations to on-road mobile source NOx emissions were predicted in both urban (either positive or negative sensitivities) and rural (positive sensitivities) locations.     

Effects of improved spatial and temporal modeling of on-road vehicle emissions

Numerous emission and air quality modeling studies have suggested the need to accurately characterize the spatial and temporal variations in on-road vehicle emissions. The purpose of this study was to quantify the impact that using detailed traffic activity data has on emission estimates used to model air quality impacts. The on-road vehicle emissions are estimated by multiplying the vehicle miles traveled (VMT) by the fleet-average emission factors determined by road link and hour of day. Changes in the fraction of VMT from heavy-duty diesel vehicles (HDDVs) can have a significant impact on estimated fleet-average emissions because the emission factors for HDDV nitrogen oxides (NOx) and particulate matter (PM) are much higher than those for light-duty gas vehicles (LDGVs). Through detailed road link-level on-road vehicle emission modeling, this work investigated two scenarios for better characterizing mobile source emissions: (1) improved spatial and temporal variation of vehicle type fractions, and (2) use of Motor Vehicle Emission Simulator (MOVES2010) instead of MOBILE6 exhaust emission factors. Emissions were estimated for the Detroit and Atlanta metropolitan areas for summer and winter episodes. The VMT mix scenario demonstrated the importance of better characterizing HDDV activity by time of day, day of week, and road type. More HDDV activity occurs on restricted access road types on weekdays and at nonpeak times, compared to light-duty vehicles, resulting in 5-15% higher NOx and PM emission rates during the weekdays and 15-40% lower rates on weekend days. Use of MOVES2010 exhaust emission factors resulted in increases of more than 50% in NOx and PM for both HDDVs and LDGVs, relative to MOBILE6. Because LDGV PM emissions have been shown to increase with lower temperatures, the most dramatic increase from MOBILE6 to MOVES2010 emission rates occurred for PM2.5 from LDGVs that increased 500% during colder wintertime conditions found in Detroit, the northernmost city modeled.     

The sensitivity of PM2.5 source-receptor relationships to atmospheric chemistry and transport in a three-dimensional air quality model

Air quality model simulations constitute an effective approach to developing source-receptor relationships (so-called transfer coefficients in the risk analysis framework) because a significant fraction of particulate matter (particularly PM2.5) is secondary (i.e., formed in the atmosphere) and, therefore, depends on the atmospheric chemistry of the airshed. In this study, we have used a comprehensive three-dimensional air quality model for PM2.5 (SAQM-AERO) to compare three approaches to generating episodic transfer coefficients for several source regions in the Los Angeles Basin. First, transfer coefficients were developed by conducting PM2.5 SAQM-AERO simulations with reduced emissions of one of four precursors (i.e., primary PM, sulfur dioxide (SO2), oxides of nitrogen (NOx), and volatile organic compounds) from each source region. Next, we calculated transfer coefficients using two other methods: (1) a simplified chemistry for PM2.5 formation, and (2) simplifying assumptions on transport using information limited to basin-wide emission reductions. Transfer coefficients obtained with the simplified chemistry were similar to those obtained with the comprehensive model for VOC emission changes but differed for NOx and SOz emission changes. The differences were due to the parameterization of the rates of secondary PM formation in the simplified chemistry. In 90% of the cases, transfer coefficients estimated using only basin-wide information were within a factor of two of those obtained with the explicit source-receptor simulations conducted with the comprehensive model. The best agreement was obtained for VOC emission changes; poor agreement was obtained for primary PM2.5.     

NO2 and SO2 dispersion modeling and relative roles of emission sources over Map Ta Phut industrial area, Thailand

Map Ta Phut industrial area (MA) is the largest industrial complex in Thailand. There has been concern about many air pollutants over this area. Air quality management for the area is known to be difficult, due to lack of understanding of how emissions from different sources or sectors (e.g., industrial, power plant, transportation, and residential) contribute to air quality degradation in the area. In this study, a dispersion study of NO2 and SO2 was conducted using the AERMOD model. The area-specific emission inventories of NOx and SO2 were prepared, including both stack and nonstack sources, and divided into 11 emission groups. Annual simulations were performed for the year 2006. Modeled concentrations were evaluated with observations. Underestimation of both pollutants was Jbund, and stack emission estimates were scaled to improve the modeled results before quantifying relative roles of individual emission groups to ambient concentration overfour selected impacted areas (two are residential and the others are highly industrialized). Two concentration measures (i.e., annual average area-wide concentration or AC, and area-wide robust highest concentration or AR) were used to aggregately represent mean and high-end concentrations Jbfor each individual area, respectively. For AC-NO2, on-road mobile emissions were found to be the largest contributor in the two residential areas (36-38% of total AC-NO2), while petrochemical-industry emissions play the most important role in the two industrialized areas (34-51%). For AR-NO2, biomass burning has the most influence in all impacted areas (>90%) exceptJor one residential area where on-road mobile is the largest (75%). For AC-SO2, the petrochemical industry contributes most in all impacted areas (38-56%). For AR-SO2, the results vary. Since the petrochemical industry was often identified as the major contributor despite not being the largest emitter, air quality workers should pay special attention to this emission group when managing air quality for the MA.     

Control of ozone precursors in a complex industrial terrain by using multiscale-nested air quality models with fine spatial resolution (1 km2)

The location of the northeastern Iberian Peninsula (NEIP) in the northwestern Mediterranean basin, the presence of the Pyrenees mountain range (with altitudes > 3000 m), and the influence of the Mediterranean Sea and the large valley canalization of Ebro river induce an extremely complicated structure for the dispersion of photochemical pollutants. Air pollution studies in very complex terrains such as the NEIP require high-resolution modeling for resolving the very complex dynamics of flows. To deal with the influence of larger-scale transport, however, high-resolution models have to be nested in larger models to generate appropriate initial and boundary conditions for the finer resolution domains. This article shows the results obtained through the utilization of the MM5-EMICAT2000-CMAQ multiscale-nested air quality model relating the sensitivity regimes for ozone (O3)-nitrogen oxides (NOx)-volatile organic compounds (VOCs) in an area of high geographical complexity, like the industrial area of Tarragona, located in the NEIP. The model was applied with fine temporal (one-hour) and spatial resolution (cells of 24 km, 2 km, and 1 km) to represent the chemistry and transport of tropospheric O3 and other photochemical species with respect to different hypothetical scenarios of emission controls and to quantify the influence of different emission sources in the area. Results indicate that O3 chemistry in the industrial domain of Tarragona is strongly sensitive to VOCs; the higher percentages of reduction for ground-level O3 are achieved when reducing by 25% the emissions of industrial VOCs. On the contrary, reductions in the industrial emissions of NOx contribute to a strong increase in hourly peak levels of O3. At the same time, the contribution of on-road traffic and biogenic emissions to ground-level O3 concentrations in the area is negligible with respect to the pervasive weight of industrial sources. This analysis provides an assessment of the effectiveness of different policies for the control of emission of precursors by comparing the modeled results for different scenarios.