不同接种量的微生物秸秆腐熟剂对蔬菜副产物堆肥效果的影响

为了明确不同接种量的微生物秸秆腐熟剂对蔬菜副产物堆肥效果的影响,以玉米秸秆为调理剂,在调节初始物料含水率为63％和C/N为28的条件下,设置了B1(堆肥混合物+1％秸秆腐熟剂)、B2(堆肥混合物+3％秸秆腐熟剂)、B3(堆肥混合物+5％秸秆腐熟剂)和CK(堆肥混合物+3％灭菌惰性载体)4个处理,测定不同堆肥处理对温度、含水率、碳氮比(C/N)、半纤维素、纤维素、木质素、总养分含量、发芽指数等指标的影响.结果表明,蔬菜副产物堆肥接种微生物秸秆腐熟剂均能够使堆肥周期缩短,有效降低堆肥含水率,提高有机质的降解幅度,并且使堆肥中半纤维素、纤维素、木质素降解率分别提高1.03％、1.16％和1.47％;氮磷钾养分含量也比不接种处理平均提高0.48％.4个处理的总体堆肥效果表现为:B2＞B1 ＞B3＞CK.     

生化黄腐酸投加量对木薯渣堆肥效果的影响

为了明确不同生化黄腐酸投加量对木薯渣堆肥效果的影响,以木薯渣、干鸡粪和烟杆粉为原料,设置了T1(堆肥原料+1‰生化黄腐酸)、T2(堆肥原料+2‰生化黄腐酸)、T3(堆肥原料+3‰生化黄腐酸)和CK(不添加生化黄腐酸的堆肥原料)4个处理,测定不同堆肥处理对温度、含水率、淀粉、水溶性碳(DOC)、纤维素、半纤维素、木质素含量以及一些腐熟程度指标的影响。结果表明,添加生化黄腐酸能促进堆体升温,有效降低堆体含水率,能使堆肥过程中淀粉、DOC、纤维素、半纤维素的降解率分别提高5.95%、5.29%、7.35%和4.95%,并且腐熟程度指标的变化也表明添加生化黄腐酸能有效促进堆肥腐熟程度,缩短腐熟周期。4个处理的总体堆肥效果表现为:T2T1T3CK,说明添加2‰的生化黄腐酸的堆肥效果最好。     

微生物菌剂和鸡粪对蔬菜废弃物堆肥化处理的影响

由于我国缺乏适用的蔬菜废物循环利用技术,致使蔬菜产地的生产废物难以处理与再循环利用而被弃置。为获得适用的蔬菜废物堆肥化处理技术,本研究以小麦秸秆为水分调理剂,并分别以鸡粪和微生物菌剂为接种剂,在初始物料含水率65%和C/N为25的条件下,设置了V1(蔬菜残体+小麦秸秆)、V2(V1+鸡粪)、V3(V2+微生物菌剂)和V4(V1+微生物菌剂)等4个处理,通过测定4个不同堆肥处理对温度、含水率、C/N比以及发芽指数(GI)等指标的影响。结果表明:同时加入微生物菌剂和鸡粪的处理(V3)可使堆肥最高温度达到67.5℃,且水分脱除效果最好,最终产品的含水率是最低的;鸡粪也是较好的接种剂,提升堆肥温度且能缩短堆肥周期;发芽率指数(GI)的结果显示,4个处理之间的堆肥腐熟成度为V3>V4>V2>V1,这进一步表明,添加微生物菌剂和鸡粪可降低堆肥产品对后茬植物发芽和生长的不良抑制。     

沉水植物与2种不同辅料混合好氧堆肥

沉水植物富含氮、磷和钾等营养元素,通过堆肥实现营养物质的回收和利用是沉水植物资源化的有效途径。但是沉水植物含水率高、碳氮比低,需要对其进行一定的优化才能实现更好的堆肥效果。本研究采用麦秸、树叶分别作为辅料和沉水植物进行混合好氧堆肥实验,沉水植物好氧堆肥作为控制组。通过测定温度、挥发分、耗氧速率、电导率、种子发芽率(GI)、总氮、总磷和总钾等以评价堆肥产品的腐熟度和养分。结果表明,沉水植物好氧堆肥具有一定可行性,堆肥产品总养分含量为6.01%,符合有机肥使用标准(NY525-2012)中对总养分的要求,具有较好腐熟度,但堆肥产品pH值为8.90,大于标准值8.50,氮素损失率为35.11%;通过分别添加麦秸、树叶与沉水植物混合堆肥,堆肥产品pH值分别为8.33和8.24,氮素损失率分别为20.25%和11.21%;由电导率、GI、碳氮比综合分析3组堆肥产品腐熟度从高到低顺序为沉水植物与树叶沉水植物与麦秸沉水植物。通过添加富碳辅料如麦秸、树叶与沉水植物混合堆肥可以提高堆肥产品腐熟度,减少氮素损失提高肥效。     

碳氮比对堆肥过程NH3挥发和腐熟度的影响

通过强制通风静态堆肥试验,研究了不同碳氮干质量比(简写为C/N)处理(17.6、24.0、32.4、40.3)对猪粪堆肥NH3挥发和腐熟度的影响.结果表明:(1)不同C/N处理间NH3变化存在极显著差异.低C/N处理的NH3挥发明显大于高C/N处理;(2)当C/N为17.6、24.0、32.4和40.3时,其氮素的损失率分别为32.19%、20.80%、13.65%和7.66%,说明C/N越低,其氮素损失越大;(3)低C/N堆肥盐分过高,会抑制种子发芽率,而高C/N会导致堆肥肥料养分含量不达标.相比之下,C/N为24.0和32.4的处理较有利于减小氮素的损失和促进堆肥的腐熟.因此,综合考虑各方面因素,堆肥的C/N控制在25～30为宜.     

添加VT菌剂和有机物料腐熟剂对堆肥的影响

通过在高温好氧堆肥中分别添加VT菌剂和有机物料腐熟剂,研究接种3‰的VT菌剂和有机物料腐熟剂促进堆肥的作用效果。结果表明,接种VT菌剂的处理与空白和接种有机物料腐熟剂的处理相比,堆肥初期升温更快;高温期更长;堆肥结束时,C/N降低的多,NO3-N增加的多,NH4+-N挥发的少,接种VT菌剂和VT有机物料腐熟剂都可促进有机质的充分降解,缩短堆肥时间,加快堆肥腐熟,提高堆肥肥力。     

接种外源微生物菌剂对香蕉茎秆堆肥的影响

为了研究接种外源微生物菌剂对香蕉茎秆堆肥的影响,本实验采用高温好氧堆肥技术,设计了对照（不接菌）、接种白腐菌及棱盖多孔菌3个处理,探讨了不同处理堆肥过程中堆体温度、水分、pH值、电导率、有机碳、C/N、发芽指数及堆肥质量的变化情况。结果表明,接种微生物菌剂处理的温度均高于对照,且高温期持续时间相对较长,以接种白腐菌处理的高温持续时间最长;接种外源微生物菌剂对堆肥含水率、pH、EC、全碳、C/N变化影响不大;与对照相比,接种白腐菌可增加全氮及全钾的含量,有利于提高堆肥产品质量;接种白腐菌处理在36 d（GI〉50%）就达到腐熟,比对照提前8 d腐熟,明显缩短堆肥腐熟时间;而接种棱盖多孔菌处理比对照推迟10 d腐熟,共需54 d不利于香蕉茎秆堆肥的进行。     

添加VT菌剂和有机物料腐熟齐对堆肥的影响

通过在高温好氧堆肥中分别添加VT菌剂和有机物料腐熟剂，研究接种3％o的VT菌剂和有机物料腐熟剂促进堆肥的作用效果。结果表明，接种VT菌剂的处理与空白和接种有机物料腐熟剂的处理相比，堆肥初期升温更快；高温期更长；堆肥结束时，C／N降低的多，NO3-N增加的多，NH4-N挥发的少，接种VT菌剂和VT有机物料腐熟剂都可促进有机质的充分降解，缩短堆肥时间，加快堆肥腐熟，提高堆肥肥力。     

复合腐秆菌剂对稻草腐熟过程的影响

为了研究复合腐秆菌剂对稻草好氧堆肥的影响,采用好氧堆肥技术,设计了不接菌(对照)和接种复合菌剂2个处理,探讨堆肥过程中堆体温度、pH、有机质、C/N、发芽指数的变化。结果表明,接种复合腐秆菌剂堆体初期温度上升迅速,最高温度达到60℃,高温发酵阶段维持了12 d;与对照相比,接种复合腐秆菌剂对pH值、容重与孔隙度、有机质、C/N变化影响不大;但增加堆体全氮的含量,提高堆肥产品的质量,种子发芽率在第20天迅速上升,最大值为93%。显然接种复合腐秆菌剂促进好氧堆肥迅速起温,提高了堆肥的腐熟质量。     

厨余垃圾堆肥间歇通风方式的可行性研究

以好氧堆肥成熟的通风方式连续通风为参考,研究了对厨余垃圾好氧堆肥采用间歇通风方式的可行性。结果表明,厨余垃圾好氧堆肥采用间歇通风方式的温度和O2体积分数变化规律与连续通风方式基本一致。腐熟度指标pH、电导率(EC)和发芽率指数(GI)均能达到厨余垃圾好氧堆肥的要求。但是间歇通风不但可以减少鼓风时间,节约成本,而且能够显著降低NH3、N2O的排放,提高总碳(TC)、总氮(TN)的积累,从而提高堆肥产品品质。因此,建议厨余垃圾好氧堆肥过程采用间歇通风方式。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染