Fenton氧化-序批式膜生物反应器耦合处理干法腈纶废水

采用Fenton氧化-序批式膜生物反应器(SBMBR)组合工艺处理干法腈纶废水。结果表明,在废水初始pH值为3.0,H2O2投加量为90.0 mmol/L,Fe2+投加量为20.0 mmol/L,反应时间为2.0 h的条件下,Fenton氧化预处理对腈纶生产废水的COD去除率达到47.0%以上,COD由1 091 mg/L降至560 mg/L,废水的BOD5/COD由0.32升至0.69,废水的可生化性得到显著提高。Fenton处理出水与丙烯腈废水等比例混合后,采用SBMBR进行生化处理,在水力停留时间为24 h,90 min缺氧/150 min好氧交替运行的条件下,COD、NH4+-N和TN的平均去除率分别为71.7%、97.2%和47.4%,碳源不足是限制TN去除效果的主要影响因素。在无外加碳源的条件下,组合工艺处理后出水COD和NH4+-N浓度分别为117 mg/L和1.7 mg/L,出水水质可以稳定达到国家一级排放标准(GB8978-1996)。     

臭氧/过氧化氢氧化活性红X-3B的实验研究

采用臭氧/过氧化氢氧化技术对活性红X-3B模拟染料废水进行处理。考察和优化了连续曝气实验条件下臭氧投加流量、反应时间、初始pH、过氧化氢投加量等因素对活性染料废水处理效果的影响。结果表明,最佳操作参数为反应时间60min、pH 10.25、臭氧投加量250mg/(L·h)、过氧化氢投加量36mg/L。在此条件下,COD去除率达到70.09%,色度去除率达到99.95%,BOD5/COD由初始的0.04提高到0.32,废水可生化性得到较好改善。     

O_3/H_2O_2深度处理印染废水二级出水

采用O3/H2O2高级氧化工艺深度处理印染废水二级出水,考察了不同反应条件对O3/H2O2工艺的影响,并且对污水二级出水有机物(Ef OM)的性质和去除行为进行了表征分析。结果表明,在p H=9,臭氧进气流量0.2 L/min,臭氧浓度116 mg/L,反应时间100 min,H2O2投加量9.79 mmol/L时,COD和色度去除率分别为82.2%、96.9%,B/C(BOD5/COD)由初始的0.10提升到0.32。此外,三维荧光光谱(3DEEM)、相对分子质量分布(MWD)以及亲疏水性分布分析表明,处理后Ef OM的荧光特性发生变化,低分子量物质大量增加,亲疏水性分布也有所改变。     

加压活性污泥法处理有机中间体废水的研究

对加压活性污泥法处理有机中间体废水进行了研究,主要考察了停留时间(HRT)、污泥浓度(MLSS)和反应压力等条件对COD去除率的影响.有机中间体废水经铁炭预处理后,COD从原来的8 000 mg/L降到5 000 mg/L左右,BOD5/COD由原来的0.20升高到0.40左右.当反应器内废水混合后COD 2 000 mg/L时,在反应压力0.10 MPa、污泥质量浓度3～5 g/L、停留时间8～10 h条件下,出水COD小于600 mg/L,COD去除率大于70%;出水经混凝沉淀处理后COD小于400 mg/L,可以达到<污水综合排放标准>(GB 8978-1996)三级标准.与常规的活性污泥处理方法相比,加压活性污泥法具有处理速度快、降解效率高和容积负荷大等优点.     

铁炭微电解预处理电路板废水

采用铁炭微电解法预处理电路板废水.结果表明,在进水pH为2.00、铁炭质量比为4:1、振荡时间为20 min的铁炭微电解静态实验最佳条件下,絮凝出水COD去除率为30%;在进水pH为2.00、铁炭质量比为4:1、水力停留时间为50 min的铁炭微电解柱动态实验最佳条件下,连续曝气.絮凝出水COD为11021 mg/L,COD去除率约为34%,BOD5/COD从0.12上升到0.32,可生化性提高,Cu2+质量浓度从9.11 mg/L下降至0.76 mg/L,降低了废水的生物毒性,为生化处理创造了条件.     

零价铁Fenton技术处理含聚乙烯醇的印染退浆废水

采用零价铁Fenton技术处理含聚乙烯醇(PVA)的印染退浆废水。通过单因素实验和正交实验,考察了初始pH、H2O2投加量、铁屑粒径及投加量和反应时间对实验结果的影响。结果表明,初始pH和H2O2投加量对处理效果影响很大。最佳反应条件是初始pH=4.0,H2O2投加量为100mmol/L,铁屑(粒径为1~3mm)投加量为15g/L,反应时间为30min。在该条件下,出水PVA质量浓度为0.9mg/L,PVA去除率为99.9%,COD去除率为23.6%,BOD5/COD由0.12升高至0.34,可生化性明显提高。无论从处理效果考虑还是从成本考虑,零价铁Fenton技术都优于传统Fenton技术。     

旋转填充床中Fenton+O_3氧化降解模拟阿莫西林废水

以旋转填充床(RPB)作为反应装置,研究了Fenton工艺与Fenton+O3工艺处理模拟阿莫西林废水的效果,考察了FeSO4·7H2O的投加量、温度、旋转床转速、液体流量及pH对COD去除率的影响。实验表明,Fenton+O3工艺的COD脱除率及BOD5/COD相对于Fenton工艺分别提升26.7%和140%。该工艺在pH为3、温度为25℃、液体流量30 L/h、气体流量2.5 L/h、转速800 r/min、H2O2的投加量为1 mmol/L及Fe2+投加量为0.4 mmol/L的条件下,100 mg/L的模拟阿莫西林废水中COD的去除率达到57.9%,BOD5/COD从0增加到0.36,满足后续生化处理要求。     

微电解-Fenton深度处理制药废水影响因素与参数控制

采用铁炭微电解-Fenton联合工艺深度处理制药废水生化出水,探讨了初始pH、曝气量、反应时间等因素对微电解出水Fe2+和Fe3+变化规律、COD降解速率以及后续Fenton氧化效果的影响,为优化微电解-Fenton氧化联合工艺提出了微电解间歇加酸的理论。间歇加酸可提高微电解系统中COD降解速率和Fe2+含量,使后续Fenton氧化无需投加FeSO4·7H2O即可达到较好的COD去除效果。结果表明,当初始pH=2.5,曝气量为0.6 m3/h,间歇加酸30 min/次,微电解反应2 h,出水投加1 mL/L的H2O2进行Fenton氧化2 h,COD总去除率可达81.33%;间歇加酸30 min/次可将微电解反应2 h出水Fe2+浓度从50 mg/L提高至151 mg/L,COD降解速率从10.6 mg COD/(L·h)提高至22.2 mg COD/(L·h)。     

Ti(Ⅳ)催化臭氧化预处理酸性难降解制药废水

考察了酸性条件下Ti(Ⅳ)催化臭氧化预处理医药废水的效能,关联了废水氧化度与可生化性(BOD5/COD)的关系。结果表明,酸性条件下O3和O3/H2O2的氧化效率明显低于Ti(Ⅳ)/H2O2/O3。原始pH条件(3.5)下,Ti(Ⅳ)/H2O2/O3体系Ti(Ⅳ)离子和H2O2的最佳浓度分别为10 mg/L和200 mg/L。调节pH值至5.0处理120 min,制药废水的化学需氧量(COD)和总有机碳(TOC)的去除率分别为56.13%和31.49%。此时水样氧化度从原来的0.388提升到了0.608,BOD5/COD值从原来的0.019升至0.297,两者呈现较好的正相关性。以上结果表明,增大pH可以提高Ti(Ⅳ)/H2O2/O3的处理效果;此外,可以考虑利用氧化度的大小来快速判断水样的可生化性。     

Fenton氧化-前置反硝化缺氧好氧池(A/O)处理荧光增白剂废水中试研究

采用Fenton氧化-前置反硝化缺氧好氧池(A/O)对荧光增白剂废水IC出水进行中试实验研究。实验表明,在Fe2+投加量为0.003 mol/L,进水pH值为3,[H2O2]/[Fe2+]为4∶1,反应时间为2 h的条件下,Fenton氧化法对COD的去除率可以达到46%以上,出水BOD5/COD的值由0.26提高到0.58。氧化后废水进入前置反硝化生物脱氮系统进行生化处理,该系统采用间歇式进水,水力停留时间为2 d,实验结果表明,A/O系统对COD、氨氮和总氮的去除率分别达41%、90%以上和86%。该组合工艺对COD的总去除率可达到67%,出水氨氮在20 mg/L以下,总氮在37 mg/L以下。     

次氯酸钠发生器的研制

介绍了电解法生产次氯酸钠的原理 ,并在原有生产工艺的基础上进行了重新设计和对设备的重新选择、改造 ,得出了各个工艺参数的最佳值 ,生产出高品质的次氯酸钠     

Estimation of uncertainty of sampling for analysis of pesticide residues

Abstract

A computer model was used to take random samples from primary sample populations obtained from field trials to simulate the uncertainty of sampling for residue analysis of plant commodities and soil. The results indicate about 40%, 30% and 20% relative uncertainty when random samples of size 5, 10 and 25 are taken respectively, from a single lot. Therefore the sample size should be the same for establishing and enforcing legal limits.     

不同泥源对厌氧氨氧化反应器启动的影响

采用2套上流式生物膜反应器,分别接种少量厌氧氨氧化污泥和大量硝化污泥,考察其对厌氧氨氧化反应器启动的影响。污泥接种入反应器后,测得接种厌氧氨氧化污泥的反应器(R1)内MLSS为0.22 g/L,另一个反应器(R2)MLSS为2.7 g/L。与直接接种厌氧氨氧化污泥相比,R1经过72 d的运行才显现出厌氧氨氧化特性。经过114 d的培养,前者氮去除速率由0.23 kg/(m3.d)提升到5.29 kg/(m3.d),总氮去除率大于89%;R2的氮去除速率由0.01 kg/(m3.d)提升到1.1 kg/(m3.d),总氮去除率大于84.6%。说明普通污泥启动需要一个较长的筛选过程,直接接种少量的厌氧氨氧化污泥比接种普通的污泥能够更快启动厌氧氨氧化反应器。     

Evaluation of the presence of drugs of abuse in tap waters

A total of seventy samples of drinking water were tested for non-controlled and illicit drugs. Of these, 43 were from Spanish cities, 15 from seven other European countries, three from Japan and nine from seven different Latin American countries. The most frequently detected compounds were caffeine, nicotine, cotinine, cocaine and its metabolite benzoylecgonine, methadone and its metabolite EDDP. The mean concentrations of non-controlled drugs were: for caffeine 50 and 19 ng L⁻¹, in Spanish and worldwide drinking water respectively and for nicotine 13 and 19 ng L⁻¹. Illicit drugs were sparsely present and usually at ultratrace level (<1 ng L⁻¹). For example, cocaine has mean values of 0.4 (Spain) and 0.3 ng L⁻¹ (worldwide), whereas for benzoylecgonine, these mean values were 0.4 and 1.8 ng L⁻¹, respectively. Higher concentrations of benzoylecgonine were found in Latin American samples (up to 15 ng L⁻¹). No opiates were identified in any sample but the presence of methadone and EDDP was frequently detected. Total mean values for EDDP were 0.4 ng L⁻¹ (Spain) and 0.3 ng L⁻¹ (worldwide). Very few samples tested positive for amphetamines, in line with the reactivity of chlorine with these compounds. No cannabinoids, LSD, ketamine, fentanyl and PCP were detected.     

An application of the theory of kinematics of mixing to the study of tropospheric dispersion

The most common technique used for numerical simulations of tracer mixing is that of the numerical solution of the advection–diffusion equation with the unresolved fluxes parameterized using the similarity theory. Despite correct predictions of the overall directions of transport, models based on a numerical solution of the advection–diffusion equation lack sufficient accuracy to correctly reproduce the coupling of mixing with small scale processes which are sensitive to the microstructure of the tracer distribution. The objective of this paper is to revisit the basic formalism employed in numerical models used to investigate atmospheric tracers. The main mathematical method proposed here is the theory of kinematics of mixing which could be applied effectively for simulations of atmospheric transport processes. At the beginning of the paper, we introduce simple mathematical transformations in order to demonstrate how complex topological structures are created by mixing processes. These idealistic flow systems are essential to explain transport properties of much more complex three-dimensional geophysical flows. An example of the application of the kinematics of mixing to the analysis of tracer transport on a planetary scale is presented in the following sections. The complex filamentary structures simulated in the numerical experiment are evaluated using some commonly applied statistical measures in order to compare the results with the data published in the literature. The results of the experiment are also analysed with the help of simple conceptual models of fluid filaments. The microstructure of the tracer distribution introduced in the paper is essential to increase our understanding of atmospheric transport and to develop more realistic parameterizations of small-scale mixing. The presented results could also be used to improve calculations of the coupling between microphysical processes and tracer mixing.     

Mechanisms of biodegradation of dibenzoate plasticizers

Biodegradation mechanisms were elucidated for three dibenzoate plasticizers: diethylene glycol dibenzoate (D(EG)DB), dipropylene glycol dibenzoate (D(PG)DB), both of which are commercially available, and 1,6-hexanediol dibenzoate, a potential green plasticizer. Degradation studies were done using Rhodococcus rhodochrous in the presence of pure alkanes as a co-substrate. As expected, the first degradation step for all of these systems was the hydrolysis of one ester bond with the release of benzoic acid and a monoester. Subsequent biodegradation of the monobenzoates of diethylene glycol (D(EG)MB) and dipropylene glycol (D(PG)MB) was very slow, leading to significant accumulation of these monoesters. In contrast, 1,6-hexanediol monobenzoate was quickly degraded and characterization of the metabolites indicated that the biodegradation proceeded by way of the oxidation of the alcohol group to generate 6-(benzoyloxy) hexanoic acid followed by β-oxidation steps. This pathway was blocked for D(EG)MB and D(PG)MB by the presence of an ether function.The use of a pure hydrocarbon as a co-substrate resulted in the formation of another class of metabolites; namely the esters of the alcohols formed by the oxidation of the alkanes and the benzoic acid released by hydrolysis of the original diesters. These metabolites were biodegraded without the accumulation of any intermediates.     

混凝试验搅拌器的研制

影响混凝效果的因素众多,混凝沉淀烧杯试验是进行水的混合、絮凝、沉淀工艺研究、设计和生产指导的最有效方法之一,阐述了智能型混凝试验搅拌器的设计原理和技术性能.     

产油微藻培养与回收的关键技术研究进展

寻找廉价而高效的替代原料是实现生物柴油产业化的关键所在.微藻以含油量高、生长周期短、环境适应能力强、生物产量高等优点,有望成为一种极具潜力的生物柴油生产原料.然而,目前尚存在微藻培养低效成本高和微藻回收效率低两大难题.综述了微藻培养与回收过程中的关键技术,并对存在的两大难题及其改进技术进行了详细的探讨.最后,总结并展望了微藻培养、回收技术未来的发展趋势.     

生物质快速热裂解主要参数对生物油产率的影响

以松木木屑为原料,在自制的小型流化床上,开展了生物质热裂解温度、生物质粒径和进料速率对生物油产率的影响实验研究.结果表明,在热裂解温度分别为450、475、500、525和550℃条件下,当热裂解温度为500℃时,生物油产率最高,平均产率达到53.33%（质量百分比）.反应温度越高,炭产量越低,不可冷凝气体产量越高,气体发热值越高;粒径＜1 mm的生物质其粒径对生物油产率影响不大;生物质进料速率增加时,生物油产率增加.本研究为生物能的利用提供了新的途径.     

造纸废水混凝处理中SFT助凝替代性研究

中小造纸厂废水处理常用PAC作混凝剂 ,PAM作助凝剂。由于PAM成本很高 ,影响了处理设备的投运率。用超细滑石粉 (SFT)替代PAM助凝 ,与混凝剂PAC配合 ,其混凝处理效果基本相当 ,但是处理成本降低 0 .10元 /m3 。由于SFT属环境无害材料 ,不会给排泥带来二次污染