The effects of operational parameters and common anions on the reactivity of zero-valent iron in bromate reduction

Bromate reduction by Fe(0) was investigated under various conditions in batch tests. The bromate was primarily reduced to bromide ions with possible adsorption onto iron. Bromate reduction by Fe(0) can be described by pseudo-first-order kinetics. The differences in surface areas, numbers of reactive sites, impurities, pretreatment methods and numbers of repeated uses of iron affected the rates of bromate reduction through reducing or accumulating a passive oxide film on the iron surface. The reduction of bromate was significantly affected by only the dissolved oxygen content at supersaturated concentrations or by decreasing the pH from 6 to 5. Increasing the temperature increased the bromate reduction rate, which followed the Arrhenius relationship with activation energy of 52.6 kJmol(-1) and the reduction rate increased with increased mixing rates. These observations indicate that bromate reduction by iron is a surface-mediated process and diffusion to the surface is essential. Under the test conditions, modest inhibitory effects on bromate reduction by Fe(0) from nitrite, chlorate and bicarbonate were observed and the inhibitory effect from phosphate was relatively larger. Enhanced reactivity of Fe(0) to bromate was observed in the presence of nitrate or sulfate. These findings suggest that bromate reduction by Fe(0) can be an effective method for bromate control.     

Simultaneous oxidation of EDTA and reduction of metal ions in mixed Cu(II)/Fe(III)-EDTA system by TiO2 photocatalysis

Both the photooxidation of EDTA and the photoreduction of metal ions in metal-EDTA systems were investigated. EDTA oxidation by TiO(2) photocatalysis occurred sequentially as Cu(II)-EDTA>Cu(II)/Fe(III)-EDTA>Fe(III)-EDTA. For Cu(II)-EDTA, EDTA was completely decomposed after only 60min of irradiation. The rate of EDTA decomposition was directly correlated with the initial Cu(II) concentration in the case of a mixed Cu(II)/Fe(III)-EDTA system. The metal ions in a single metal-EDTA complex were removed following significant decomposition of EDTA. For a mixed Cu(II)/Fe(III)-EDTA system, however, no copper was removed whereas almost all of the iron was removed. The iron and copper species deposited on the TiO(2) surface were identified via EPR and XPS as mixed FeO/Fe(3)O(4) and Cu(0)/Cu(2)O, respectively.     

Effect of metal ions and humic acid on the dechlorination of tetrachloroethylene by zerovalent iron

The dechlorination of tetrachloroethylene (PCE) by zerovalent iron (Fe(0)) in the presence of metal ions and humic acid was investigated. In the absence of metal ion and humic acid, 64% of the initial PCE was dechlorinated after 125 h with the production of ethane and ethene as the major end products. The dechlorination followed pseudo-first-order kinetics and the normalized surface rate constant (k(SA)) for PCE dechlorination was (3.43+/-0.61)x10(-3)lm(-2)h(-1). Addition of metal ions enhanced the dechlorination efficiency and rate of PCE, and the enhancement effect followed the order Ni(II)>Cu(II)>Co(II). The k(SA) for PCE dechlorination in the presence of metal ions were 2-84 times higher than that in the absence of metal ions. X-ray photoelectron spectroscopy (XPS) showed that Cu(II) and Ni(II) were reduced by Fe(0) to zerovalent metals, and resulted in the formation of bimetallic system to accelerate the dechlorination reaction. On the contrary, humic acid out-competed the reactive sites on iron surface with PCE, and subsequently decreased the dechlorination efficiency and rate of PCE by Fe(0). However, the reactivity of Fe(0) for PCE dechlorination in the presence of metal ions and humic acid increased by a factor of 3-161 when compared to the iron system containing humic acid alone. Since humic acid and metal ions are the most often found co-existing compounds in the contaminated aquifers with chlorinated hydrocarbons, results obtained in this study is useful to better understand the feasibility of using Fe(0) for long-term application to the remediation of contaminated sites.     

Reduction of Ag(I), Au(III), Cu(II), and Hg(II) by Fe(II)/Fe(III) hydroxysulfate green rust

Green rusts are mixed Fe(II)/Fe(III) hydroxides that are found in many suboxic environments where they are believed to play a central role in the biogeochemical cycling of iron. X-ray absorption fine structure analysis of hydroxysulfate green rust suspensions spiked with aqueous solutions of AgCH(3)COO, AuCl(n)(OH)(4-n), CuCl(2), or HgCl(2) showed that Ag(I), Au(III), Cu(II), and Hg(II) were readily reduced to Ag(0), Au(0), Cu(0), and Hg(0). Imaging of the resulting solids from the Ag(I)-, Au(III)-, and Cu(II)-amended green rust suspensions by transmission electron microscopy indicated the formation of submicron-sized particles of Ag(0), Au(0), and Cu(0). The facile reduction of Ag(I), Au(III), Cu(II), and Hg(II) to Ag(0), Au(0), Cu(0), and Hg(0), respectively, by green rust suggests that the presence of green rusts in suboxic soils and sediments can have a significant impact on the biogeochemistry of silver, gold, copper, and mercury, particularly with respect to their mobility.     

Studies on removal of metal ions and sulphate reduction using rice husk and Desulfotomaculum nigrificans with reference to remediation of acid mine drainage

The utility of rice husk as an adsorbent for metal ions such as iron, zinc and copper from acid mine water was assessed. The adsorption isotherms exhibited Langmuirian behavior and were endothermic in nature. The free energy values for adsorption of the chosen metal ions onto rice husk were found to be highly negative attesting to favorable interaction. Over 99% Fe(3+), 98% of Fe(2+) and Zn(2+) and 95% Cu(2+) uptake was achieved from acid mine water, with a concomitant increase in the pH value by two units using rice husk. The remediation studies carried out on acid mine water and simulated acid mine water pretreated with rice husk indicated successful growth of Desulfotomaculum nigrificans (D. nigrificans). The amount of sulphate bioreduction in acid mine water at an initial pH of 5.3 was enhanced by D. nigrificans from 21% to 40% in the presence of rice husk filtrate supplemented with carbon and nitrogen. In simulated acid mine water with fortified husk filtrate, the sulphate reduction was even more extensive, with an enhancement to 73%. Concurrently, almost 90% Fe(2+), 89% Zn(2+) and 75% Cu(2+) bioremoval was attained from simulated acid mine water. Metal adsorption by rice husk was confirmed in desorption experiments in which almost complete removal of metal ions from the rice husk was achieved after two elutions using 1M HCl. The possible mechanisms of metal ion adsorption onto rice husk and sulphate reduction using D. nigrificans are discussed.     

Effect of biogenic iron species and copper ions on the reduction of carbon tetrachloride under iron-reducing conditions

In this study, the cell-mediated and abiotic reduction of carbon tetrachloride (CCl(4)) by biogenic iron species produced from the reductive dissolution of ferrihydrite in the presence of Geobacter sulfurreducens and copper ions (Cu(II)) were investigated. 9,10-Anthraquinone-2,6-disulfonate (AQDS), serving as a surrogate of natural organic matters and an electron shuttling compound, was added to enhance the efficiency of biological reduction of the solid Fe(III) minerals. G. sulfurreducens drove the reduction of CCl(4), primarily through the formation of biogenic surface-bound iron species produced from the reductive dissolution of ferrihydrite, in the presence of 10microM AQDS. The pseudo-first-order rate constant (k(obsCT)) for CCl(4) transformation in the presence of ferrihydrite was 3.0 times higher than that resulting from the use of G. sulfurreducens alone. Addition of 0.5mM Cu(II) slightly inhibited both the growth of G. sulfurreducens and the production of biogenic Fe(II). However, the k(obsCT) values for CCl(4) transformation in ferrihydrite suspensions containing G. sulfurreducens and 0.3-0.5mM Cu(II) were 2.1-4.2 times higher than that observed in the absence of Cu(II). X-Ray powder diffraction analysis indicated that the added Cu(II) reacted with the biogenic Fe(II) ions to produce catalytic cuprous ions (Cu(I)) and secondary iron oxide minerals such as magnetite and goethite, resulting in accelerating the chemical transformation efficiency and rate of CCl(4) under iron-reducing conditions.     

The enhancement methods for the degradation of TCE by zero-valent metals

Batch tests were performed to compare the degradation rates of TCE on Fe0 and Zn0. Our results indicated that the degradating capability of Zn0 to TCE was nearly 10 times higher than that of Fe0. On the other hand, the degradation rates of Fe0 or Zn0 in conjunction with other metals for reduction of TCE was investigated. The selected metals were nickel (Ni0) and palladium (Pd0) both of which have a strong enhancement effect. The reduction rates of Zn0/Pd0 and Zn0/Ni0 for TCE were the fastest. Fe0 that had lost its surface activity could be activated again by the addition of Pd0 or Ni0.     

Effect of amorphous silica and silica sand on removal of chromium(VI) by zero-valent iron

The effect of two surfaces (amorphous silica and silica sand) on the reduction of chromium(VI) by zero-valent iron (Fe(0)) was investigated using batch reactors. The amendment of both surfaces significantly increased the rate and extent of Cr(VI) removal. The rate enhancement by amended surfaces is presumed to result from scavenging of Fe(0)-Cr(VI) reaction products by the provided surfaces, which minimized surface deactivation of Fe(0). The rate enhancing effect was greater for silica compared to sand, and the difference is attributed to silica's higher surface area, greater affinity for reaction products and pH buffering effect. For a given mass of Fe(0), the reactivity and longevity of Fe(0) to treat Cr(VI) increased with increasing dose of silica. Elemental analyses of the reacted iron and silica revealed that chromium removed from the solution was associated with both surfaces, with its mass distribution being approximately 1:1 per mass of iron and silica. The overall result suggests reductive precipitation was a predominant Cr(VI) removal pathway, which involves initial reduction of Cr(VI) to Cr(III), followed by formation of Cr(III)/Fe(III) hydroxides precipitates.     

Regeneration of iron for trichloroethylene reduction by Shewanella alga BrY

Zero valent iron (ZVI), the primary reactive material in several permeable reactive barriers, is often oxidized to ferrous or ferric iron, resulting in decreased reactivity with time. Iron reducing bacteria can reconvert the ferric iron to its ferrous form, prolonging the reduction of chlorinated organic contaminants. In this study, the reduction of Fe(II,III) oxide and Fe(III) oxide by a strain of iron reducing bacteria of the group Shewanella alga BrY(S. alga BrY) was observed in both aqueous and solid phases. S. alga BrY preferentially reduced dissolved ferric iron over the solid ferric iron. In the presence of iron oxide the Fe(II) ions reduced by S. alga BrY efficiently reduced trichloroethylene (TCE). On the other hand, Fe(II) produced by S. alga BrY covered the reactive surfaces of ZVI iron filings and inhibited the reduction of TCE by ZVI. The formation of precipitates on the iron oxide or Fe0 surface was confirmed by scanning electron microscopy. The results suggest that iron-reducing bacteria in the oxidized Fe0 barriers can enhance the removal rate of chlorinated organic compounds and influence on the long-term performance of Fe0 reactive barriers.     

超声波/零价铁降解对硝基苯胺的试验研究

对在超声波、零价铁和超声波/零价铁(U/Fe0)等体系中对硝基苯胺的降解规律进行了研究。研究结果表明,对硝基苯胺在超声波作用下,降解规律符合一级反应动力学模型,但超声波对高浓度的对硝基苯胺降解效果较差。在U/Fe0体系中,超声波和零价铁对降解对硝基苯胺具有协同作用,对硝基苯胺降解速率显著提高。降解机理显示,对硝基苯胺在零价铁表面上发生原电池反应,被还原为对苯二胺,在超声波作用下进一步降解。在U/Fe0体系中添加Cu2+,形成Fe/Cu原电池,可进一步促进对硝基苯胺的降解速率,降解效率优于铸铁屑形成的Fe/C原电池。     

Iron-mediated reactions of polychlorinated biphenyls in electrochemical peroxidation process (ECP)

A study was conducted to explore some of the basic processes of polychlorinated biphenyl (PCB) destruction by a new technology termed electrochemical peroxidation process (ECP). ECP represents an enhancement of the classic Fenton reaction (H2O2 + Fe2+) in which iron is electrochemically generated by steel electrodes. Focus was on the extent of adsorption of a mixture of Aroclor 1248 on steel electrodes in comparison to iron filings. Commercially available zero-valent iron filings rapidly adsorbed PCBs from an aqueous solution of Aroclor 1248. Within 4 h, all the PCBs were adsorbed at 1%, 5%, and 10% Fe0 (w/v) concentrations. Little difference in adsorption was found between acidic (2.3) and unamended solutions (pH 5.5), even though significant differences in iron oxidation state and Fe2+ concentrations were measured in solution. PCB adsorption also occurs on steel electrodes regardless of the pH or electric current applied (AC or DC), suggesting the combination of oxidizing (free radical-mediated reactions) and reducing (dechlorination reactions) iron-mediated degradation pathways may be possible. Extraction of the iron powder after 48 h of contact time yielded the progressive recovery of biphenyl with increasing Fe mass(from 0.4% to 3.5%) and changes of the PCB congener-specific pattern as a consequence of dechlorination. A variety of daughter congeners similar to those accumulated during anaerobic microbial dechlorination of Aroclor 1248 in contaminated sediments indicate preferential removal of meta- and para-chlorines.     

Nitrate reduction by fluoride green rust modified with copper

Nitrate reduction by the fluoride form of green rust modified with copper (GR-F(Cu)) was investigated using a batch reactor system. The extent of nitrate reduction was measured by measuring the increase in concentration of ammonia, which is the final product of nitrate reduction by GR. This approach was required, because nitrate could be removed from solution by ion exchange without reduction. The rate of ammonium production was investigated over the range of pH 7.8-11. The fastest reaction was achieved at pH 9 when GR was present at a concentration of 0.083M as Fe(II) and 1mM of Cu(II) was added. The rate at pH 9 was enhanced by a factor of 2.5 compared to that at pH 7.8 by comparing the time elapsed to transform all nitrate to ammonium. Kinetics of nitrate reduction by GR-F at pH 7.8 were affected by the concentration of Cu(II) added. The rate constants for ammonium production increased from 0.012 to 1.52h(-1) as Cu(II) additions increased from 0 to 2.5mM, but the reaction rate at 5mM was slightly decreased to 1.25h(-1). The mechanism of enhanced rates of nitrate reduction by addition of Cu(II) could not be fully determined in this study. However, XRD results showed that magnetite was produced in the reaction of Cu(II) and GR-F and SEM shows the production of nano-size particles which were not fully identified in this study. In addition, the concentration of Fe(II) in GR was observed to linearly decrease with concentration of Cu(II) added.     

Removal of metal ions and humic acid from water by iron-coated filter media

Iron oxide is an excellent, regenerable adsorbent, and often controls free metals through adsorption reaction. The utilization of heating process for coating iron oxide on sand surface allowed the media to be used in a packed column. Iron-coated sand was investigated for adsorbing metal ions and natural organic matter from water by batch and column experiments. Chemical analysis (energy dispersive analysis of X-ray, EDAX) was used for characterizing the copper and lead adsorption sites on iron-coated sand. From the batch experiment results, the copper and lead ions could be removed simultaneously by the iron-coated sand in the competition adsorption system. The interaction between copper, lead ions and iron oxide on sand surface was primarily the chemical bonds. The maximum adsorption capacities of iron-coated sand for copper and lead were 0.259 mg Cu/g-sand and 1.211 mg Pb/g-sand, respectively. The presence of humic acid led to increase the adsorption of copper and lead. Results from column experiments indicated that the copper ions, lead ions and humic acid could be removed completely before the breakpoint. Consequently, the iron-coated sand may be applied for the adsorption/filtration of metal ions and natural organic matters from water.     

Catalytic reduction of NO on copper/MCM-41 studied by in situ EXAFS and XANES

Speciation of copper in the channels of MCM-41 during reduction of NO with CO at 473-773 K was studied by in situ extended X-ray absorption fine structural (EXAFS) and X-ray absorption near edge structural (XANES) spectroscopies in the present work. The component fitted (in situ) XANES spectra of the catalyst showed that about 72% of metallic copper (Cu(0)) in MCM-41 was oxidized to higher oxidation state coppers (Cu(II) (46%) and Cu(I) (26%)) during the NO reduction process (at 473 K). By EXAFS, we also found that in the NO reduction process, oxygen was inserted into the metallic copper matrix and led to a formation of the copper oxide species with a Cu-O bond distance of 1.93 A which was greater than that of the model compound Cu(2)O (typically 1.86 A). At 573-673 K, mainly Cu(II) was found in the channels of MCM-41. Nevertheless, at a higher temperature (e.g., 773 K), about 61% Cu(I), 31% Cu(II), and 8% Cu(O) with averaged Cu-Cu and Cu-O bond distances of 3.04 and 1.88 A, respectively were observed, that might account for the high selectivity-to-decomposition (S/D) ratios for yields of N(2) and CO(2) in the catalytic reduction of NO with CO.     

铜-胺改性ZSM-5吸附剂的制备及其对NOx的净化机理

以ZSM-5分子筛粉体为原料，成型后负载铜盐和有机胺改性，制备出一种高效脱除氮氧化物的吸附剂。通过改变铜盐、有机胺的含量以及铜盐活化温度使吸附剂的性能得到优化，在实验条件下（NO₂初浓度1 000 mg/m³，气流2.7 L/min）床层对NO₂动态吸附的透过时间由改性前的3 min提高到90 min，并使NO气体的释放得到有效减缓。通过动态吸附实验研究了NO释放时间在负载前后的变化，通过X射线光电子能谱（XPS）和红外分析（FTIR）研究了吸附剂表面铜元素、有机基团等在吸附前后的变化规律，提出了可能的净化机理。     

Influence of complex reagents on removal of chromium(VI) by zero-valent iron

The removal of Cr(VI) by zero-valent iron (Fe(0)) and the effect of three complex reagents, ethylenediaminetetraacetic acid (EDTA), NaF and 1,10-phenanthroline, on this reaction were investigated using batch reactors at pH values of 4, 5 and 6. The results indicate that the removal of Cr(VI) by Fe(0) is slow at pH 5.0 and that three complex reagents play different roles in the reaction. EDTA and NaF significantly enhance the reaction rate. The zero-order rate constants at pH 5.0 were 5.44 microM min(-1) in the presence of 4mM EDTA and 0.99 micrM min(-1) in the presence of 8 mM NaF, respectively, whereas that of control was only 0.33 micrM min(-1), even at pH=4.0. This enhancement is attributed to the formation of complex compounds between EDTA/NaF and reaction products, such as Cr(III) and Fe(III), which eliminate the precipitates of Cr(III), Fe(III) hydroxides and Cr(x)Fe(1-)(x)(OH)(3) and thus reduce surface passivation of Fe(0). In contrast, 1,10-phenanthroline, a complex reagent for Fe(II), dramatically decreases Cr(VI) reduction by Fe(0). At pH=4.0, the zero-order rate constant in the presence of 1mM of 1,10-phenanthroline was 0.02 micrM min(-1), decreasing by 99.7% and 93.9%, respectively, compared with the results in the presence and absence of EDTA. The results suggest that a pathway of the reduction of Cr(VI) to Cr(III) by Fe(0) may involve dissolution of Fe(0) to produce Fe(II), followed by reduction of Cr(VI) by Fe(II), rather than the direct reaction between Cr(VI) and Fe(0), in which Fe(0) transfers electrons to Cr(VI).     

Synthesis of a clinoptilolite-Fe system with high Cu sorption capacity

An iron oxide-clinoptilolite system was synthesized by adding natural clinoptilolite in an iron nitrate solution under strongly basic condition. The newly synthesized material has a red-brown color. A combination of XRD, FTIR and EPR spectroscopies, as well as specific surface area measurements and TG/DSC thermal analyses provided information on the type of Fe species located on the zeolite surface. Clinoptilolite seems to maintain its structure, while Fe(3+) species are in a symmetric environment (Th or Oh). The new material has a noteworthy high value of specific surface area (151 m(2)g(-1)) and is fully iron exchanged (Fe/Al=1.23). Differences in FTIR and TG/DSC spectrograms between the Fe-Clin system and untreated Clin were reported and explained. According to Cu adsorption/desorption experiments, carried out after the synthesis and characterization procedures, the Fe-Clin system is a promising new material since it adsorbs significantly larger Cu concentrations than clinoptilolite. This fact is owed to its high specific surface area and to its high negative surface charge. Desorption of Cu was also examined and it was observed that the Fe-Clin system desorbs smaller Cu amounts than untreated clinoptilolite.     

Iron improving bio-char derived from microalgae on removal of tetracycline from aqueous system

Novel magnetic carbonaceous bio-char was hydrothermal prepared from microalgae under different loadings of iron and its structures and surface chemistry were characterized with Fourier transform infrared (FTIR), X-ray photoelectron spectroscopy (XPS), scanning electron microscopy (SEM), and nitrogen adsorption-desorption isotherm (BET). The morphology of bio-char changed from sheet to particle as iron loading increased and its surface area also increased. When 3.0 g of dried microalgae and 6.0 mmol iron salt ((NH₄)₂SO₄·FeSO₄·6H₂O) were mixed and treated, the obtained bio-char possessing the highest amount of oxygen-containing functional groups resulted in the best adsorption performance on tetracycline (TC). This adsorption process was fitted to Langmuir adsorption isotherm and the maximum adsorption capacity was 95.86 mg/g, which is higher than other bio-char reported. The iron loading contributed to the higher adsorption capacity of bio-char, which may be due to three factors, the high surface area, more hydrogen bonding, and bridging effects of the structural Fe for TC. Our data suggest that bio-char may have more important role in stabilization of pollutants in the environment.     

Abiotic Fe(III) induced mineralization of phenolic substances

The redox process between iron(III) (in dissolved form and as the mineral phase ferrihydrite) and phenolic substances has been examined. We investigated the relationship between the structure and reactivity for the dihydrobenzene reductants catechol, hydroquinone and resorcine, and for the 2-methoxyphenol guaiacol with iron(III), by determining the rate of the Fe(III) reduction as well as the production of CO2. This work demonstrates that catechol and guaiacol will be effectively oxidized to CO2 by reducing iron(III). Hydroquinone shows a reduction of iron(III), but no accompanying mineralization could be determined. In contrast, resorcine showed no reaction with Fe(II). The deciding factor on whether or not mineralization occurs were controlled by the position of the hydroxy groups. It is shown that phenolic substances with two hydroxy groups in the orthoposition or at least one hydroxy group and a methoxy group can be oxidized to CO2 while iron(III) is reduced.     

Adsorption/desorption of copper by a sandy soil amended with various rates of manure, sewage sludge, and incinerated sewage sludge

Organic amendments are sometimes applied to agricultural soils to improve the physical, chemical, and microbiological properties of the soils. The organic fractions in these soil amendments also influence metal reaction, particularly the adsorption and desorption of metals, which, in turn, determine the bioavailability of the metals and hence their phytotoxicities. In this study, a Quincy fine sandy (mixed, mesic, Xeric Torripsamments) soil was treated with 0 to 160 g kg(-1) rates of either manure, sewage sludge (SS), or incinerated sewage sludge (ISS) and equilibrated in a greenhouse at near field capacity moisture content for 100 days. Following the incubation period, the soil was dried and adsorption of copper (Cu) was evaluated in a batch equilibration study at either 0, 100, 200, or 400 mg L(-1) Cu concentrations in a 0.01M CaCl2 solution. The desorption of adsorbed Cu was evaluated by three successive elutions in 0.01M CaCl2. Copper adsorption increased with an increase in manure rates. At the highest rate of manure addition (160 g kg(-1) soil), Cu adsorption was two-fold greater than that by the unamended soil at all rates of Cu additions. With increasing rates of Cu additions, the adsorption of Cu decreased from 99.4 to 77.6% of Cu applied to the 160 g kg(-1) manure amended soil. The desorption of Cu decreased with an increase in rate of manure amendment. Effects of sewage sludge amendments on Cu adsorption were somewhat similar to those as described for manure additions. Likewise, the desorption of Cu was the least at the high rate of SS addition (160 g kg(-1)), although at the lower rates there was not a clear indication of the rate effects. In contrast to the above two amendments, the ISS amendment had the least effect on Cu adsorption. At the highest rate of ISS amendment, the Cu adsorption was roughly 50% of that at the similar rate of either manure or SS amendments, across all Cu rates.