纳米四氧化三铁对2,4-D的脱氯降解

采用纳米四氧化三铁(Fe3O4)降解水溶液中的2,4-二氯苯氧乙酸(2,4-D),考察了2,4-D初始浓度、纳米Fe3O4投加量、溶液pH和温度等因素对2,4-D降解率的影响.结果表明,纳米Fe3O4对2,4-D有显著的降解效果,初始浓度为10 mg/L的2,4-D, 48 h内降解率可达48%.纳米Fe3O4对2,4-D的降解是一个还原脱氯过程,反应体系中氯离子浓度随2,4-D浓度降低而升高.LC/MS分析表明,2,4-D降解的主要产物是苯酚,其他中间产物是2,4-二氯苯酚(2,4-DCP)、4-氯苯酚(4-CP)和2-氯苯酚(2-CP).溶液中2,4-D的降解符合准一级反应动力学,产物4-CP、2,4-DCP和苯酚的反应速率常数K分别为0.0043、0.0026和0.0032 h -1.环境条件对降解效率有显著影响,2,4-D初始浓度在0～10 mg/L、纳米Fe3O4投加量0～300 mg/L的范围内,2,4-D降解率随初始浓度和纳米Fe3O4投加量的增加而增大;pH对2,4-D的脱氯降解有显著影响,在pH为3.0时,纳米Fe3O4对2,4-D的还原脱氯效果最好;温度升高,可以提高脱氯反应速率.     

电-Fenton氧化降解2,4-二氯酚

以气体扩散电极为阴极,以Ti/SnO₂-Sb₂O₅-IrO₂为阳极,构建了电-Fenton氧化系统降解水中2,4-DCP(2,4-二氯酚),在考察气体扩散阴极产生H₂O₂适宜电位基础上,研究了初始 c (Fe2+)和电化学反应时间对2,4-DCP降解的影响以及反应过程中 c (H₂O₂)、 c (Fe2+)和ρ(Cl-)的变化. 结果表明:该方法联合了电-Fenton氧化和钛基氧化物阳极氧化2种作用共同降解2,4-DCP,在阴极电位为-0.7 V、 c (Fe2+)为0.15 mmol/L、反应60 min时,2,4-DCP去除率为89.1%;反应120 min时,2,4-DCP的吸收特征峰完全消失,去除率达到100%;反应240 min时,ρ(TOC)降至9.15 mg/L,去除率达79.4%. 反应体系中ρ(H₂O₂)与ρ(Fe2+)呈负相关. 2,4-DCP被降解后,其苯环上的氯主要以Cl-的形式存在于溶液中.      

改性Ti/SnO2-Sb电极催化降解1,4-二氯苯废水试验研究

采用聚合物前驱体法制备了未掺杂、掺杂Cu、掺杂Bi、掺杂Ni的4种Ti/Sn O2-Sb电极,运用SEM和XRD分析电极表面形貌及结构,通过线性极化扫描、循环伏安等测试考察其电化学性能,同时进行1,4二氯苯(p-DCB)降解实验进一步探究电极的电催化氧化特性.SEM和XRD结果表明,掺杂金属可改善电极表面形貌,增大其比表面积;电化学测试表明,Ti/Sn O2-Sb电极的析氧电位并未因金属掺杂而有明显改变,掺杂金属后,Ti/Sn O2-Sb电极具有更优的电催化活性和稳定性.p-DCB降解实验表明,改性Ti/Sn O2-Sb电极对p-DCB的降解效率明显提高,其中Ti/Sn O2-Sb-Cu电极的电催化处理效果最优,电解2 h后p-DCB的去除率即达到87.6%,且p-DCB的降解反应遵循一级反应动力学规律.     

热处理对SnO2/Ti电化学催化降解p-苯醌的影响

用热分解方法制备了钛基二氧化锡阳极(SnO₂/Ti),对比研究了空气/氧气2种热处理气氛对电极性能的影响.用扫描电镜(SEM)观察了电极表面形貌,对电极表面主要膜元素的化学状态进行了X射线光电子能谱(XPS)分析,对电极在不同溶液的动电位极化行为进行了测试,研究了2种电极在5mA/cm²恒电流状态下对p-苯醌的电解催化去除性能.SEM观察表明,2种电极表面都为典型的泥裂形貌,但在氧气气氛中退火处理的电极具有更大的活性表面积.XPS分析发现,在氧气气氛中退火处理的电极表面Sn3d_5/2、Sb3d_5/2电子的结合能较在空气气氛中退火处理的低0.15eV.动电位极化测试结果与恒电流电解实验结果都表明,在氧气气氛中退火处理的电极对水中p-苯醌具有更好的电化学催化去除性能.在电解进行至溶液完全脱色的情况下,氧气气氛中退火处理的电极对水中TOC的去除率为76.3%,而空气气氛中退火处理的电极对水中TOC的去除率为63.3%.在2种电极条件下,溶液中TOC浓度随电解时间的变化规律均符合指数变化规律.     

ZVI/EDDS/Air体系降解水中2,4-二氯酚的研究

建立零价铁(ZVI)、乙二胺二琥珀酸(EDDS)和曝气三者组成的类Fenton(ZVI/EDDS/Air)处理体系,考察了初始EDDS浓度、铁粉投加量、曝气速率、2,4-二氯酚(2,4-DCP)浓度、初始pH以及反应温度等对水溶液中2,4-DCP降解的影响.结果表明,该体系能有效降解2,4-DCP,并且其降解规律符合准一级动力学方程.在2,4-DCP质量浓度100 mg·L-1、EDDS浓度0.80 mmol.L-1、铁粉投加量20 g·L-1、曝气速率为2 L.(min.L)-1的最佳实验条件下室温反应1 h,2,4-DCP的降解率达到99%.ZVI/EDDS/Air体系对氯酚的降解较ZVI/EDTA/Air体系具有环境友好、反应条件温和,而且对2,4-DCP的降解效果好等优点.     

纳米级Pd/Fe@SiO2复合颗粒对2,4-DCP的还原脱氯研究

为有效抑制纳米级Pd/Fe颗粒的团聚和钝化及改善其表面特性,将纳米SiO_2包覆在Pd/Fe颗粒表面,超声波辐照下液相还原法制备纳米级Pd/Fe@SiO_2复合颗粒,采用TEM、SEM、XRD、EDX及BET表征其物性,以2,4-二氯苯酚(2,4-DCP)为目标污染物,探究其对2,4-DCP的还原脱氯影响因素、降解机理和动力学,结果表明:制备的纳米级颗粒粒径均匀、分散性好,比表面积大;体系中纳米级Pd/Fe投加量、钯化率、TEOS投加量、反应温度及溶液初始pH均会对2,4-DCP的降解效果产生明显影响;并推测出纳米级Pd/Fe@SiO_2复合颗粒对2,4-DCP的降解机理即快速吸附—逐步脱氯—最终脱附释放,其降解符合拟一级动力学关系.     

Enhanced dechlorination of 2,4-dichlorophenol by recoverable Ni/Fe–Fe3O4 nanocomposites

Ni/Fe-Fe_3O_4 nanocomposites were synthesized for dechlorination of 2,4-dichlorophenol(2,4-DCP). The effects of the Ni content in Ni/Fe-Fe_3O_4 nanocomposites, solution pH, and common dissolved ions on the dechlorination efficiency were investigated, in addition to the reusability of the nanocomposites. The results showed that increasing content of Ni in Ni/Fe–Fe_3O_4 nanocomposites, from 1 to 5 wt.%, greatly increased the dechlorination efficiency; the Ni/Fe–Fe_3O_4 nanocomposites had much higher dechlorination efficiency than bare Ni/Fe nanoparticles. Ni content of 5 wt.% and initial p H below 6.0 was found to be the optimal conditions for the catalytic dechlorination of 2,4-DCP. Both 2,4-DCP and the intermediate product 2-chlorophenol(2-CP) were completely removed, and the concentration of the final product phenol was close to the theoretical phenol production from complete dechlorination of 20 mg/L of 2,4-DCP, after 3 hr reaction at initial p H value of 6.0,3 g/L Ni/Fe-Fe_3O_4 , 5 wt.% Ni content in the composite, and temperature of 22℃. 2,4-DCP dechlorination was enhanced by Cl-and inhibited by NO3-and SO_4~(2-). The nanocomposites were easily separated from the solution by an applied magnetic field. When the catalyst was reused, the removal efficiency of 2,4-DCP was almost 100% for the first seven uses, and gradually decreased to 75% in cycles 8–10. Therefore, the Ni/Fe–Fe_3O_4 nanocomposites can be considered as a potentially effective tool for remediation of pollution by 2,4-DCP.     

电化学氧化PFOA阳极材料筛选及其机制研究

全氟辛酸(PFOA)具有环境持久性及内分泌干扰性,传统的生物降解及高级氧化法对PFOA的去除效果微弱.本研究采用电化学氧化法降解PFOA,选取BDD(掺硼金刚石电极)、Pt、Ti、Ti/RuO2、Ti/RuO2-IrO2、Ti/In2O3、Ti/SnO2-Sb2O5-IrO2、Ti/SnO2-Sb2O5-RhO2、Ti/SnO2-Sb2O5、Ti/SnO2-Sb2O5-CeO2和Ti/SnO2-Sb2O5-Bi2O3这11种阳极材料为备选电极.采用线性扫描伏安法测试析氧电位(OEP),评价11种电极对PFOA的降解效果和脱氟效果,并采用超声-电化学协同方法间接证明PFOA分子在电极表面的直接电子转移是降解反应的第一步.Ti/SnO2-Sb2O5-Bi2O3、Ti/SnO2-Sb2O5-CeO2、Ti/SnO2-Sb2O5和BDD对PFOA有较好的电氧化效果,降解率分别是89.8%、89.8%、93.3%和98.0%.Pt、Ti/SnO2-Sb2O5-RhO2、Ti/SnO2-Sb2O5-IrO2和Ti/In2O3对PFOA的电氧化效果微弱,降解率分别是2.1%、2.3%、12.5%和3.1%.而Ti、Ti/RuO2和Ti/RuO2-IrO2对PFOA没有电氧化能力.PFOA分子经过电极表面的直接电化学氧化发生脱羧反应,后经过逐步脱掉CF2单元的循环生成短链的全氟羧酸类化合物C6F13COO-、C5F11COO-、C4F9COO-和C3F7COO-.     

钛基改性DSA电极氧化法去除水中全氟化合物

为了提高金属氧化物电极(DSA电极)的稳定性及催化活性,实现全氟化合物(PFCs)的高效降解,分别以溶胶涂覆法和电沉积法制备了改性DSA(Ti/SnO_2-ZnO)电极,并用于全氟辛酸(PFOA)和全氟辛烷磺酸(PFOS)的电化学降解过程研究.实验分别考察了电流密度、溶液初始pH、 PFOA与PFOS初始浓度对PFCs降解效果的影响.结果表明:两种方法制备的改性DSA电极表面均匀负载了SnO_2-ZnO复合涂层.在二维电极体系中,极板面积约为65.0 cm~2,电流密度为20.0 mA·cm~(-2),极板间距为15.0 mm,电解质为1.30 g·L~(-1)次氯酸钠溶液以及电解时间为150 min时,溶胶涂覆法和电沉积法所制备的Ti/SnO_2-ZnO电极对初始浓度为100 mg·L~(-1)的PFOA和PFOS分别在pH为3.50和6.50时去除效果最佳,分别达到了90.6%、94.6%和91.0%、93.7%;循环使用电极3次,其降解过程均符合准一级反应动力学,且电沉积法制备的电极效果优于溶胶涂敷法,表现出对PFCs类污染物稳定、高效的去除能力.     

Ti/RuO2-IrO2电极电化学方法降解溶液中TBBPA及其降解机理探究

四溴双酚A(TBBPA)是世界上产量和用量最大的溴代阻燃剂之一,在河流、底泥及污水中持久存在,严重威胁环境和人体健康.探讨了阳极为Ti/RuO_2-IrO_2电极的电化学法对溶液中TBBPA的降解效率,并考察了电流密度(5~20 m A·cm~(-2))、初始pH值(3~11)、极板间距(1~3 cm)及电解质浓度(1~40 mmol·L~(-1))对降解速率的影响.研究结果表明,TBBPA的降解遵循一级动力学方程,在溶液初始浓度为5 mg·L~(-1)、电流密度为10 mA·cm~(-2)、电解质浓度为5 mmol·L~(-1)及极板间距为1 cm的条件下,60 min后TBBPA的降解率可达97.2%,且降解速率常数和半衰期分别为0.060 min~(-1)和11.6 min,能量消耗为105.3 k Wh·m~(-3).同时运用HPLC-MS/MS检测出中间产物双酚A(BPA)和2-溴苯酚,并推断其降解途径主要为在羟基自由基(·OH)作用下连续的脱溴过程中,苯环与异丙基之间的C—C键断裂生成BPA和2-溴苯酚.电化学法是一种高效的、有潜力的降解难降解有机污染物的方法,本文将为今后实际废污水中TBBPA的去除提供基础数据和技术参数.     

Immobilization of self-assembled pre-dispersed nano-TiO2 onto montmorillonite and its photocatalytic activity

The immobilization of pre-dispersed Ti O_2 colloids onto the external surface of the clay mineral montmorillonite(Mt) was accomplished and regulated via a self-assembly method employing the cationic surfactant cetyltrimethylammonium bromide(CTAB). The role of CTAB in the synthesis process was investigated by preparing a series of Ti O_2-CTAB-Mt composites(TCM) with various CTAB doses. The results indicated that a uniform and continuous Ti O_2 film was deposited on the external surface of montmorillonite in the composite synthesized with 0.1 wt.% of CTAB, and the TCM nano-composites showed much higher values for specific surface area, average pore size and pore volume than the raw montmorillonite clay. Then, the formed TCM materials were applied in photocatalytic degradation of 2,4-dichlorophenol(2,4-DCP) in aqueous solution. The degradation efficiency reached as high as 94.7%. Based on the degradation intermediates benezoquinone, fumaric acid and oxalic acid identified by LC–MS analysis, a mechanism for the photocatalytic oxidation of 2,4-DCP on Ti O_2/Mt nano-composites is proposed.     

Immobilization of self-assembled pre-dispersed nano-TiO2 onto montmorillonite and its photocatalytic activity

The immobilization of pre-dispersed TiO₂ colloids onto the external surface of the clay mineral montmorillonite (Mt) was accomplished and regulated via a self-assembly method employing the cationic surfactant cetyltrimethylammonium bromide (CTAB). The role of CTAB in the synthesis process was investigated by preparing a series of TiO₂-CTAB-Mt composites (TCM) with various CTAB doses. The results indicated that a uniform and continuous TiO₂ film was deposited on the external surface of montmorillonite in the composite synthesized with 0.1 wt.% of CTAB, and the TCM nano-composites showed much higher values for specific surface area, average pore size and pore volume than the raw montmorillonite clay. Then, the formed TCM materials were applied in photocatalytic degradation of 2,4-dichlorophenol (2,4-DCP) in aqueous solution. The degradation efficiency reached as high as 94.7%. Based on the degradation intermediates benezoquinone, fumaric acid and oxalic acid identified by LC–MS analysis, a mechanism for the photocatalytic oxidation of 2,4-DCP on TiO₂/Mt nano-composites is proposed.     

Electrochemical oxidation of 1H,1H,2H,2H-perfluorooctane sulfonic acid (6：2 FTS) on DSA electrode：Operating parameters and mechanism

The 6:2 FTS was the substitute for perfluorooctane sulfonate(PFOS) in the chrome plating industry in Japan. Electrochemical oxidation of 6:2 FTS was investigated in this study. The degradabilities of PFOS and 6:2 FTS were tested on the Ti/SnO2–Sb2O5–Bi2O3anode. The effects of current density,potential,and supporting electrolyte on the degradation of 6:2 FTS were evaluated. Experimental results showed that 6:2 FTS was more easily degraded than PFOS on the Ti/SnO2–Sb2O5–Bi2O3anode. At a low current density of 1.42 mA/cm2,6:2 FTS was not degraded on Ti/SnO2–Sb2O5–Bi2O3,while the degradation ratio increased when the current density ranged from 4.25 to 6.80 mA/cm2. The degradation of 6:2 FTS at current density of 6.80 mA/cm2 followed pseudo first-order kinetics with the rate constant of 0.074 hr-1. The anodic potential played an important role in the degradation of 6:2 FTS,and the pseudo first-order rate constants increased with the potential. The surface of Ti/SnO2–Sb2O5–Bi2O3was contaminated after electrolysis at constant potential of 3 V,while the fouling phenomenon was not observed at 5 V. The fouled anode could be regenerated by incinerating at 600°C. The intermediates detected by ultra-performance liquid chromatography coupled with a triple-stage quadrupole mass spectrometer(UPLC–MS/MS) were shorter chain perfluorocarboxylic acids. The 6:2 FTS was first attacked by hydroxyl radical,and then formed perfluorinated carboxylates,which decarboxylated and removed CF2 units to yield shorter-chain perfluorocarboxylic acids.     

Ti/Ti4O7阳极电化学氧化降解水中的美托洛尔

等离子喷涂法制备了钛基亚氧化钛电极(Ti/Ti_4O_7),以该电极为阳极,研究了电化学氧化法对水中美托洛尔的去除效果.考察了电流密度(5~25 mA·cm~(-2))、极板间距(5~25 mm)和初始浓度(3~50 mg·L~(-1))对美托洛尔电化学降解效率的影响;分析美托洛尔电化学降解过程中溶液总有机碳(TOC)和毒性的变化,鉴别反应中间产物并计算其毒性.研究表明:Ti/Ti_4O_7阳极电化学降解美托洛尔反应符合一级反应动力学规律(R20.95),降解效率随电流密度的增大而增大,随极板间距和初始浓度的增大而减小;TOC去除率在反应40 min后可达56.5%;反应过程中产生了质合比为266、250、223和207的中间产物,造成美托洛尔溶液的生物毒性在电化学反应过程中先升高后下降.     

双极电化学氧化降解水中苯胺

采用钛基氧化物涂层材料（Ti/SnO2-Sb2O5）为阳极,石墨为阴极,在含Fe2＋和不含Fe2＋2种电解质条件下研究了苯胺的电化学氧化降解效率和机制.结果表明,Ti/SnO2-Sb2O5阳极氧化降解有机物的电位约2.0 V±0.1 V,而石墨阴极还原O2生成H2 O2的优化电位为-0.65 V.H2 O2单独作用不能...     

水质对UV/H_2O_2降解2,4-二氯酚的影响

研究了UV/H2O2工艺对2,4-二氯酚(2,4-DCP)的去除效果和水中阴离子、腐殖酸对该工艺降解2,4-DCP的影响。结果表明:UV/H2O2工艺可以有效的去除水中2,4-DCP,光降解过程符合一级反应动力学模型;在H2O2投加量为8mg/L,1个30W低压汞灯照射下,2,4-DCP在蒸馏水和自来水中光降解速率常数分别为0.0232/min和0.0162/min;NO3-、Cl-、HCO3-对2,4-DCP光降解有抑制作用;当3种离子浓度为0.5mmol/L、10mmol/L、20mmol/L时,对2,4-DCP光降解的抑制程度为HCO3->NO3->Cl-;随着离子浓度增大,抑制作用增强;自来水中的光降解速率常数低于蒸馏水中的光降解速率常数是由于水中多种离子影响的结果;腐殖酸在低浓度时,促进光降解反应的进行,在高浓度时,2,4-DCP的光降解氧化受到抑制。     

RGO/TiO2光催化降解2,4-二氯苯氧乙酸研究

通过Hummers法及紫外光/热还原工艺制得还原氧化石墨烯(RGO),采用溶胶-凝胶-煅烧法,以RGO和钛酸酊脂为前驱体制备出RGO/TiO2光催化复合材料,并利用XRD、FT-IR等对其进行了表征.对RGO/TiO2光催化降解性能的研究发现,复合光催化剂RGO/TiO2对2,4-二氯苯氧乙酸(2,4-D)的光催化降解活性显著优于纯TiO2,并且发现负载量和pH值对光催化降解性能有较大的影响:RGO/TiO2投加量为1.2g·L~(-1)、RGO负载量2%、pH为3、初始浓度为50 mg·L~(-1)反应12 h,2,4-D去除率达到98.75%;2,4-D降解率随着RGO/TiO2投加量的增大先增大后减小;RGO/TiO2对2,4-D的降解为脱氯还原和催化氧化过程,产生氯酚、苯酚等中间产物.     

腐殖酸在氯离子体系中的电解氧化特性

通过小型实验对腐殖酸模拟废水进行了电解氧化处理,考察了阳极材料、氯离子初始浓度对腐殖酸电解氧化处理效果的影响,探讨了腐殖酸在电解处理过程中分子量分布的变化及电解产生的低分子量产物组成.研究结果表明,PbO2阳极的电解处理效果比 Ru-Ir/Ti阳极的处理效果好,当废水在氯离子体系中电解时.可缩小2种阳极对CODCr去除效果的差距;电解后溶液中溶解性有机物的分子量分布向小分子量方向转变;当溶液中有氯离子存在时,电解过程产生的 ClO-的间接氧化作用可有效地将大分子有机物降解为小分子有机物.腐殖酸在氯离子体系中电解生成的低分子量化合物主要有 CO2、氯仿、乙酸、苯酚、苯乙醇、2H-1,4 氯苯基双氮杂卓-2-1,1-(1,1-二甲基乙基)-萘酚、3-(3-羧基-4-羟基-5-硝基酚)-D-丙氨酸等.     

气升式内循环蜂窝陶瓷反应器降解2,4-二氯酚的研究

从以2,4-二氯酚(2,4-DCP)长期驯化的好氧活性污泥中分离出一株以2,4-DCP为唯一碳源的菌种,将这种菌固定在气升式内循环蜂窝陶瓷反应器内,研究了此反应器在半连续流运行时,对2,4-DCP单基质及其与苯酚共基质时对污染物的降解情况及降解动力学.结果表明,2,4-DCP单基质时,反应器对氯酚的去除效果随着实验次数的增加而加快;2,4-DCP与苯酚共基质时,苯酚的降解速率随着半连续流实验次数的增加而加快,而氯酚的降解速率则表现出下降的趋势.此外,还研究了此反应器在连续流运行时对2,4-DCP的降解,水     

阴极原位产H2O2强化光电催化降解水中EDTA的研究

本研究构建了以活性碳纤维(Activated Carbon Fiber,ACF)为阴极,TiO_2/Ti与Ru O_2/Ti为双阳极的光电催化体系.该体系中,Ru O_2/Ti电阳极和TiO_2/Ti光阳极均有氧化作用,可同时氧化降解污染物;且电阳极具有较强析氧作用,能产生大量O_2;ACF阴极具有还原作用,可将体系中产生的O_2原位还原为H_2O_2;H_2O_2在紫外光下产生·OH,进而强化光电催化与电催化氧化过程,实现对水中乙二胺四乙酸二钠(EDTA)的高效去除.本论文详细考察了电流密度、pH、曝气等因素对EDTA降解效果的影响.结果表明,在EDTA初始浓度为300 mg·L~(-1)、溶液初始pH=4.84、电流密度为12 m A·cm~(-2)和光电流密度为0.012 m A·cm~(-2)的条件下,反应90 min后,EDTA降解率高于90%.该催化体系实现了EDTA的高效降解.