首页 | 本学科首页   官方微博 | 高级检索  
相似文献
 共查询到20条相似文献,搜索用时 375 毫秒
1.
CeO2–TiO2composite supports with different Ce/Ti molar ratios were prepared by a homogeneous precipitation method, and V2O5–WO3/CeO2–TiO2catalysts for the selective catalytic reduction(SCR) of NOx with NH3 were prepared by an incipient-wetness impregnation method. These catalysts were characterized by means of BET, XRD, UV–Vis,Raman and XPS techniques. The results showed that the catalytic activity of V2O5–WO3/TiO2 was greatly enhanced by Ce doping(molar ratio of Ce/Ti = 1/10) in the TiO2 support.The catalysts that were predominantly anatase TiO2 showed better catalytic performance than the catalysts that were predominantly fluorite CeO2. The Ce additive could enhance the surface adsorbed oxygen and accelerate the SCR reaction. The effects of O2 concentration, ratio of NH3/NO, space velocity and SO2 on the catalytic activity were also investigated. The presence of oxygen played an important role in NO reduction. The optimal ratio of NH3/NO was 1/1 and the catalyst had good resistance to SO2 poisoning.  相似文献   

2.
采用等体积浸渍法制备了锰氧化物负载凹凸棒石(MnOx/PG)低温SCR催化剂,通过SO2暂态响应、程序升温表面反应(TPSR)等实验技术研究了烟气中SO2对催化剂SCR脱硝活性的影响行为.采用程序升温脱附(TPD)、BET比表面及孔径分布测定、XPS等表征技术对催化剂硫中毒的机理及化学本质进行了深入分析.结果表明,低温下烟气中SO2对MnOx/PG催化剂的SCR脱硝活性存在显著的抑制作用,催化剂中毒主要由烟气中SO2的催化氧化引起.一方面SO2氧化为SO3后与NH3及H2O竞争反应形成复杂的硫酸铵盐堵塞催化剂孔道,另一方面与活性组分MnO2结合形成MnSO4使得部分活性组分形态发生变迁.其中硫酸铵盐的形成可通过适当的热处理得以去除,而MnSO4则不可恢复,但催化剂SCR活性却显著增加,表明MnSO4的形成不是催化剂失活的主要因素.吸附态的硫可显著增加催化剂表面酸性,因此对SCR活性有促进作用.催化剂失活主要机理为:由气相SO2的连续氧化并与NH3相结合形成硫酸铵盐,并且在低温下难以分解,以致堵塞催化剂活性中心.  相似文献   

3.
采用共沉淀法合成了TiO_2及TiO_2-Fe_2O_3载体,并对硫酸氢铵与上述载体之间的相互作用及硫酸氢铵的具体分解行为进行了研究.结果表明,催化剂载体表面含硫官能团主要以双齿硫酸盐的形式存在,含氮官能团以铵根离子的形式存在.当硫酸氢铵沉积于催化剂载体表面时,由于硫酸根离子具有较强的电负性,Ti原子及Fe原子处于电子缺失状态.对于TiO_2载体,硫酸根离子主要与Ti原子相连;而对于TiO_2-Fe_2O_3载体,Ti原子及Fe原子均为硫酸根离子主要的附着位点.采用热分析方法及原位红外对硫酸氢铵在TiO_2及TiO_2-Fe_2O_3载体表面的分解行为进行了研究,发现铁氧化物的添加显著促进了硫酸氢铵在低温区间内的分解行为;与铵根离子相比,硫酸根离子具有更高的热稳定性.催化剂稳定性测试结果表明,铁氧化物的添加显著提高了低温抗硫抗水性能,为实现低温SCR技术的工业应用提供了理论基础.  相似文献   

4.
The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.  相似文献   

5.
V2O5/TiO2催化剂中毒机理的试验研究   总被引:1,自引:0,他引:1  
选择性催化还原(SCR)催化剂是SCR烟气脱硝技术的核心,是整个SCR系统脱硝效率和经济性的决定因素.本文工作的主要研究思路是以钒钛SCR催化剂为研究对象,研究了H2O和SO2,以及相同含量下K、Na、Ca、Pb的氧化物对钒钛催化剂NO转化率的影响.H2O的存在会抑制V2O5/TiO2催化剂脱硝活性,而SO2在一定程度上促进(V2O5/TiO2)催化剂的SCR脱硝反应,提高NO转化率;碱金属K对钒钛催化剂的钝化作用都是最强,K2O和Na2O的掺入会抑制钒钛催化剂上V2O5的还原能力,而CaO和PbO的掺入对钒钛催化剂上V2O5的还原能力影响较小.  相似文献   

6.
Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.  相似文献   

7.
为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩(EP)为载体,采用溶胶-凝胶法,在不同煅烧氛围(O2和/或NH3)下制备Fe2O3/TiO2负载EP的光催化复合材料〔Fe2O3-TEP(O2)、Fe2O3-TEP(NH3)、Fe2O3-TEP(O2,NH3)、Fe2O3-TEP(NH3,O2)〕,采用EDS(X-射线色散能谱)、BET(比表面积及孔径分析)、XRD(X射线衍射)、SEM(扫描电子显微镜)、XPS(X射线光电子能谱)等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO2以锐钛矿型存在,Fe2O3的掺杂增强了TiO2对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe2O3-TEP(O2,NH3)的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe2O3-TEP(NH3,O2)、Fe2O3-TEP(O2)和Fe2O3-TEP(NH3)4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe2O3-TEP(O2,NH3)、Fe2O3-TEP(NH3,O2)、Fe2O3-TEP(O2)和Fe2O3-TEP(NH3)相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料(Fe2O3-TEP)经煅烧后所得矿相均一;Fe2O3掺杂TiO2可形成Ti—O—Fe键,减小TiO2固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O2后NH3煅烧条件下所得材料的光催化性能最佳.   相似文献   

8.
Ce-ZrO2 is a widely used three-way catalyst support.Because of the large surface area and excellent redox quality,Ce-ZrO2 may have potential application in selective catalytic reduction(SCR) systems.In the present work,Ce-ZrO2 was introduced into a low-temperature SCR system and CeO2 and ZrO2 supports were also introduced to make a contrastive study.Mn/CeO2,Mn/ZrO2 and Mn/Ce-ZrO2 were prepared by impregnating these supports with Mn(NO3)2 solution,and have been characterized by N2-BET,XRD,TPR,TPD,XPS,FT-IR and TG.The activity and resistance to SO2 and H2O of the catalysts were investigated.Mn/Ce-ZrO2 and Mn/CeO2 were proved to have better low-temperature activities than Mn/ZrO2,and yielded 98.6% and 96.8% NO conversion at 180°C,respectively.This is mainly because Mn/Ce-ZrO2 and Mn/CeO2 had higher dispersion of manganese oxides,better redox properties and more weakly adsorbed oxygen species than Mn/ZrO2.In addition,Mn/Ce-ZrO2 showed a good resistance to SO2 and H2O and presented 87.1% NO conversion,even under SO2 and H2O treatment for 6 hours,and the activity of Mn/Ce-ZrO2 was almost restored to its original level after cutting off the injection of SO2 and H2O.This was due to the weak water absorption and weak sulfation process on the surface of the catalyst.  相似文献   

9.
富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究   总被引:4,自引:2,他引:2  
考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO2/Al2O3催化剂上丙烯选择性还原NOx的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO2/Al2O3催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO2/Al2O3催化剂相比,溶胶-凝胶法制备的5%SnO2/Al2O3催化剂受水蒸汽的抑制作用较弱,并且在水和SO2共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NOx转化率的提高.  相似文献   

10.
SO2对Ag/Al2O3催化剂上CH3OH还原NO性能的影响   总被引:1,自引:0,他引:1  
用溶胶-凝胶混合法制备了Ag负载量为5%的Ag/A12O3催化剂.研究了富氧条件下,SO2对CH3OH在催化剂上还原NO性能的影响.结果表明,反应气不含SO2和H2O时,NO还原活性温度较低,有显著量N2O生成,这被归因为反应过程中,部分氧化态Ag被还原为金属Ag.添加SO2或同时添加SO2和H2相似文献   

11.
The effect of pretreatment on Pd/Al2O3 catalysts for the catalytic oxidation of o-xylene at low temperature was studied by changing the pretreatment and testing conditions. The fresh and pretreated Pd/Al2O3 catalysts were characterized by transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS) and X-ray diffraction (XRD). The results showed that the pretreatment dramatically changed the Pd/PdO ratio and then significantly affected the Pd/Al2O3 activity; while the pretreatment had not much influence on Pd particle size. The Pd/Al2O3 pre-reduced at 300℃/400℃, which has fully reduced Pd species, showed the highest activity; while the fresh Pd/Al2O3, which has fully oxidized Pd species, presented the worst performance, indicating the Pd chemical state plays an important role in the catalytic activity for the o-xylene oxidation. It is concluded that metallic Pd is the active species on the Pd/Al2O3 catalyst for the catalytic oxidation of o-xylene at low temperature.  相似文献   

12.
Carbon-modified titanium dioxide(TiO2) was prepared by a sol-gel method using tetrabutyl titanate as precursor, with calcination at various temperatures, and tested for the photocatalytic oxidation(PCO) of gaseous NH3 under visible and UV light. The test results showed that no samples had visible light activity, while the TiO2 calcined at 400℃ had the best UV light activity among the series of catalysts, and was even much better than the commercial catalyst P25. The catalysts were then characterized by X-ray diffractometry, Brunauer-Emmett-Teller adsorption analysis, Raman spectroscopy, thermogravimetry/differential scanning calorimetry coupled with mass spectrometry, ultraviolet-visible diffuse reflectance spectra, photoluminescence spectroscopy and in situ diffuse reflectance infrared Fourier transform spectroscopy. It was shown that the carbon species residuals on the catalyst surfaces induced the visible light adsorption of the samples calcined in the low temperature range( 300℃). However, the surface acid sites played a determining role in the PCO of NH3 under visible and UV light over the series of catalysts. Although the samples calcined at low temperatures had very high SSA, good crystallinity, strong visible light absorption and also low PL emission intensity, they showed very low PCO activity due to their very low number of acid sites for NH3 adsorption and activation. The TiO2 sample calcined at 400℃ contained the highest number of acid sites among the series of catalysts, therefore showing the highest performance for the PCO of NH3 under UV light.  相似文献   

13.
The present article studies the effect of CeO2 and Al2O3 on the activity of Pd/Co3O4/cordierite catalyst in conversion of NO, CO, CnHm. The catalysts were characterized by temperature programmed reduction with hydrogen, X-ray diffraction, X-ray photoelectron spectroscopy and transmission electron microscopy. It is shown that the effect of CeO2 on the properties of Pd/Co3O4/cordierite catalyst depends on preparation method. The catalyst obtained by co-deposition of cerium and cobalt oxides has higher activity in CO oxidation (CO + O2 and CO + NO) and total hexane oxidation (C6H14 + O2). Such phenomenon is probably caused by more than stoichiometric amount of formed oxygen vacancies, an increase in both mobility of surface oxygen and dispersity of components in the catalytic composition. It is demonstrated that CeO2 addition promotes the SO2 resistance of Pd/Co3O4/cordierite. The second support decreases the activity of Pd/Co3O4/cordierite catalyst in the reactions of CO and C6H14 with oxygen because of CoAl2O4 formation.  相似文献   

14.
This study introduced TiO2-pillared clays (TiO2-PILC) as a support for the catalytic oxidation of NO and analyzed the performance of chromium oxides as the active site of the oxidation process. Cr-based catalysts were prepared by a wet impregnation method. It was found that the 10 wt.% chromium doping on the support achieved the best catalytic activity. At 350℃, the NO conversion was 61% under conditions of GHSV = 23600 hr^-l. The BET data showed that the support particles had a mesoporous structure. Hz-TPR showed that Cr(10)TiP (10 wt.% Cr doping on TiO2-PILC) clearly exhibited a smooth single peak. EPR and XPS were used to elucidate the oxidation process. During the NO + O2 adsorption, the intensity of evolution of superoxide ions (O2^-) increased. The content of Cr^3+ on the surface of the used catalyst was 40.37%, but when the used catalyst continued adsorbing NO, the Cr^3+ increased to 50.28%. Additionally, Oα/Oβ increased markedly through the oxidation process. The NO conversion decreased when SO2 was added into the system, but when the SO2 was removed, the catalytic activity recovered almost up to the initial level. FT-IR spectra did not show a distinct characteristic peak of SO4^2-.  相似文献   

15.
在低温选择性催化还原(SCR)反应条件下考察了烟气残余SO2对Mn/TiO2和Mn-Ce/TiO2催化剂选择性催化还原活性的影响,同时对SO2的影响机理进行了探讨.结果发现,Mn/TiO2催化剂在SO2反应气氛中失活很快,硫铵盐的沉积和活性组分的硫酸化是催化剂失活的重要原因;Ce的加入可以有效地抑制催化剂活性组分的硫酸化,同时还能降低硫酸盐在催化剂表面的稳定性,从而可以提高催化剂的抗硫性.  相似文献   

16.
采用浸渍法制备了一系列不同钒和钨负载量的V2O5-WO3/TiO2催化剂样品,对样品NH3选择性催化还原NO性能进行了评价,并用BET、XRD、XPS等手段对催化剂样品的表面形态进行了表征.研究发现,钒的负载量对催化剂的比表面积和催化活性有显著影响,当钒负载量从1%升高到8%时,催化剂比表面积下降了16 m2/g,最高活性温度降低了约100℃.钨起到稳定剂和助剂的双重作用,当钒负载量为1%时,钨负载量从0升高到6%,催化剂比表面积仅下降了3 m2/g,而活性温度窗口向高温和低温各拓宽了约50℃.研究表明钒和钨负载量都能影响催化剂表面的VOx物种,但对催化剂的表面晶型没有明显影响.  相似文献   

17.
CeO2改性MnOx/Al2O3的低温SCR法脱硝性能及机制研究   总被引:3,自引:2,他引:1  
采用凝胶溶胶法制备大比表面积的Al2O3载体,等体积浸渍法配制负载MnOx和CeO2组分的CeO2-MnOx催化剂.以NH3为还原剂,一定的空气流速及合适的气体配比的条件下,考察所制备的催化剂在70~300℃范围内低温SCR法的脱硝性能及机制,同时分别对催化剂进行BET、XRD、SEM等表征实验,研究催化剂的理化性质....  相似文献   

18.
A series of cobalt doped TiO_2(Co-TiO_2) and Co Oxloaded TiO_2(Co/TiO_2) catalysts prepared by sol–gel and impregnation methods respectively were investigated on selective catalytic reduction with NH_3(NH_3-SCR) of NO. It was found that Co-TiO_2 catalyst showed more preferable catalytic activity at low temperature range. From characterization results of XRD,TEM, Raman and FT-IR, Co species were proved to be doped into TiO_2 lattice by replaced Ti atoms. After being characterized and analyzed by NH_3-TPD, PL, XPS, EPR and DRIFTS, it was found that the better NH_3-SCR activities of Co-TiO_2 catalysts, compared with Co/TiO_2 catalyst, were ascribed to the formation of more oxygen vacancies which further promoted the production of more superoxide ions(O-2). The superoxide ions were crucial for the formation of low temperature SCR reaction intermediates(NO-3) by reacting with adsorbed NO molecule. Therefore, these aspects were responsible for the higher low temperature NH_3-SCR activity of Co-TiO_2 catalysts.  相似文献   

19.
孙正男  杨琦  纪冬丽  郑琳 《环境科学》2015,36(6):2154-2160
以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.  相似文献   

20.
二氧化硫(SO_2)是一种常见的大气污染物,目前关于SO_2对木本植物的毒害作用及相关机制并不清楚.本文以木本植物胡杨的愈伤细胞为材料,研究SO_2衍生物对胡杨细胞的致死效应,以及过氧化氢(H_2O_2)与一氧化氮(NO)在SO_2诱导胡杨细胞死亡中的信号调节作用.研究发现:SO_2衍生物处理(1~5 mmol·L-1)可诱发胡杨细胞死亡,且SO_2衍生物浓度越大、处理时间越长,细胞死亡率越高.2 mmol·L-1SO_2衍生物处理胡杨细胞后,胞内H_2O_2和NO水平显著升高,且H_2O_2水平的升高先于NO.一定浓度的外源H_2O_2或NO供体SNP能够提高SO_2胁迫下胡杨细胞的死亡率;而使用H_2O_2清除剂CAT和ASA、NO清除剂c PTIO、NO合成抑制剂钨酸钠后,SO_2诱导的细胞死亡率明显降低.进一步实验发现,外源H_2O_2可以提高SO_2胁迫下胡杨细胞的硝酸还原酶(NR)活性,促进胞内NO产生;而利用CAT和ASA清除H_2O_2后,细胞NR活性和NO产生均受到明显抑制.此外,SO_2胁迫下,外源SNP能够抑制抗氧化酶(CAT和APX)活性,增加胡杨细胞内的H_2O_2水平,而一定浓度的c PTIO和钨酸钠均可提高CAT和APX活性,降低胞内H_2O_2水平.结果表明:SO_2胁迫下,胡杨细胞快速产生的H_2O_2能够激活硝酸还原酶活性,促进NO生成,同时NO能够通过抑制抗氧化酶活性而提高H_2O_2水平.H_2O_2与NO互作调控SO_2诱导的胡杨细胞死亡.  相似文献   

设为首页 | 免责声明 | 关于勤云 | 加入收藏

Copyright©北京勤云科技发展有限公司  京ICP备09084417号