超声辅助法制备新型FeMOR分子筛催化NOx还原反应性能研究

采用超声辅助浸渍法成功合成了高铁含量的Fe MOR-5%-UL催化剂,并且测试其催化还原NO性能.研究发现在超声辅助条件下浸渍制得的催化剂可以引入更高比例的离子交换位上的孤立的Fe~(3+),这些铁离子具有更强的NO还原活性,因此超声辅助浸渍法制备的催化剂催化性能显著高于传统的离子交换法和浸渍法.其中活性最高的FeMOR-5%-UL催化剂在添加SO_2等多种气氛时,催化活性下降不显著.并且在持续100 h的汽车尾气条件下进行的稳定性实验中,FeMOR-5%-UL的催化活性没有明显下降.FeMOR-5%-UL的优异的催化活性和稳定性非常具有应用前景和研究价值.     

Pt/CeO2催化氧化甲苯反应机制研究

采用浸渍法制备了Pt/CeO_2和Pt/Al2O_3催化剂,并通过XRD、BET、ICP-OES、H2-TPR、XPS等手段表征其物理化学性质.结果发现,Pt/CeO_2和Pt/Al2O_3催化剂上Pt负载量约为0.6%,Al2O_3载体上Pt颗粒尺寸更小,Pt/CeO_2的可还原性更强.甲苯催化氧化活性评价结果表明,Pt/CeO_2催化剂表现出更好的催化活性,T50=170℃,T90=190℃.通过UV-Raman、甲苯TPD、GC/MS、In-situ FTIR等手段进一步研究发现,Pt/CeO_2活化甲苯及反应供氧的机制与Pt/Al2O_3存在区别,其活性更好是因为:(1)负载在CeO_2表面存在高电子密度的Pt原子,具有更强的活化甲苯能力,可以直接使苯基和甲基间的C—C链发生断裂;(2)Pt的负载促进了CeO_2氧空位形成,进一步提高了CeO_2的储氧性能,加速氧循环.除了Pt解离气相氧之外,CeO_2还可以提供活性氧物种参与催化氧化甲苯的反应,进一步提高甲苯催化氧化效率.     

Influences of pH value in deposition-precipitation synthesis process on Pt-doped TiO2 catalysts for photocatalytic oxidation of NO

This work has been undertaken to study the influences of pH value on the characteristics and activity of photocatalyst by deposition-precipitation method during its preparation process. A series of Pt-modified TiO₂ were prepared by deposition-precipitation method at different pH values as well as wet impregnation method, and characterized by XRD, XPS, TEM, UV-Vis and photoluminescence (PL). It was found that the catalysts had the highest photocatalytic activity for NO conversion when pH value was kept at around 7. And the sample prepared by deposition-precipitation method showed higher activity than that by impregnation method. This was mainly due to their high value in highly-dispersed platinum oxides (PtOx) content on the surface of the catalysts. The results from UV-Vis absorption showed that highest absorbance was obtained for Pt/TiO₂ prepared at pH values of around 7. And PL spectra results indicated that the recombination rate of photogenerated electrons and holes of the samples prepared by deposition-precipitation method was lower than that prepared by impregnation method. And in the zeta potential study, the pH values for the isoelectric point of the preparing slurry of 0.05 wt.%Pt/TiO₂ and 0.5 wt.%Pt/TiO₂ were determined to be 6.5-8.5, which further confirmed the enrichment of PtOx dopants for the catalysts repapered when pH value was around 7.     

Remarkable promotion effect of trace sulfation on OMS-2 nanorod catalysts for the catalytic combustion of ethanol

OMS-2 nanorod catalysts were synthesized by a hydrothermal redox reaction method using MnSO₄ (OMS-2-SO₄) and Mn(CH₃COO)₂ (OMS-2-AC) as precursors. SO₄^2 −-doped OMS-2-AC catalysts with different SO₄^2 − concentrations were prepared next by adding (NH₄)₂SO₄ solution into OMS-2-AC samples to investigate the effect of the anion SO₄^2 − on the OMS-2-AC catalyst. All catalysts were then tested for the catalytic oxidation of ethanol. The OMS-2-SO₄ catalyst synthesized demonstrated much better activity than OMS-2-AC. The SO₄^2 − doping greatly influenced the activity of the OMS-2-AC catalyst, with a dramatic promotion of activity for suitable concentration of SO₄^2 − (SO₄/catalyst = 0.5% W/W). The samples were characterized by X-ray diffraction (XRD), field emission scanning electron microscopy (FE-SEM), transmission electron microscopy (TEM), X-ray photoelectron spectroscopy (XPS), inductively coupled plasma optical emission spectroscopy (ICP-OES), NH₃-TPD and H₂-TPR techniques. The results showed that the presence of a suitable amount of SO₄^2 − species in the OMS-2-AC catalyst could decrease the Mn–O bond strength and also enhance the lattice oxygen and acid site concentrations, which then effectively promoted the catalytic activity of OMS-2-AC toward ethanol oxidation. Thus it was confirmed that the better catalytic performance of OMS-2-SO₄ compared to OMS-2-AC is due to the presence of some residual SO₄^2 − species in OMS-2-SO₄ samples.     

铂、钯蜂窝催化剂高温老化对甲醇深度氧化的影响

本研究对铂、钯蜂窝催化剂及分别添加助化剂CeO_2或WO_3,并于500℃、700℃、900℃或1100℃下经受热老化4h后,考察催化剂比表面、晶相结构及其对甲醇深度氧化活性、产物分布及反应动力学网络变化的情况。实验证明,添加CeO_2后,降低了铂催化剂的耐高温性能,但对钯催化剂无明显影响。添加WO_3,降低了钯催化剂对甲醇的氧化活性。经X-线衍射分析证明,在1100℃高温下,WO_3与堇青石载体中的氧化镁和氧化钙发生强相互作用,生成了相应的钨酸盐。甲醇氧化反应动力学研究表明,甲醇在新鲜和高温热老化的铂催化剂上,反应动力学网络表示式是有区别的。     

The selective catalytic reduction of NO over Ce0.3TiOx-supported metal oxide catalysts

A Ce_(0.3)TiO_xoxide carrier was synthesized via a sol–gel process,and Ce_(0.3)TiO_xsupported metal(M=Cd,Mn,Fe,W,Mo)oxide catalysts were prepared by the method of incipient-wetness impregnation.The catalysts were characterized by means of X-ray diffraction(XRD),Brunauer–Emmett–Teller(BET)analysis,scanning electron microscopy(SEM),transmission electron microscopy(TEM),Fourier transform infrared(FT–IR)spectroscopy,UV–Visdiffusereflectancespectroscopy(UV–VisDRS),and Temperature-programmed reduction with H_2(H_2-TPR).The catalytic activities for de-NO_(x )were evaluated by the NH_3-SCR reaction.Among all the catalysts tested,the 2 wt.%Cd/Ce_(0.3)TiO_xcatalyst exhibited the best NH_3-SCR performance,with a wide temperature window of 250–450°C for NO conversion above 90%.Moreover,the catalyst showed N_2 selectivity greater than 99%from 200 to 450°C.     

Choice of precipitant and calcination temperature of precursor for synthesis of NiCo2O4 for control of CO–CH4 emissions from CNG vehicles

Compressed natural gas(CNG)is most appropriate an alternative of conventional fuel for automobiles.However,emissions of carbon-monoxide and methane from such vehicles adversely affect human health and environment.Consequently,to abate emissions from CNG vehicles,development of highly efficient and inexpensive catalysts is necessary.Thus,the present work attempts to scan the effects of precipitants(Na_2CO_3,KOH and urea)for nickel cobaltite(Ni Co_2O_4)catalysts prepared by co-precipitation from nitrate solutions and calcined in a lean CO-air mixture at 400°C.The catalysts were used for oxidation of a mixture of CO and CH_4(1:1).The catalysts were characterized by X-ray diffractometer,Brunauer–Emmett–Teller surface-area,X-ray photoelectron spectroscopy;temperature programmedreductionandScanningelectronmicroscopycoupledwith Energy-Dispersive X-Ray Spectroscopy.The Na_2CO_3was adjudged as the best precipitant for production of catalyst,which completely oxidized CO-CH_4mixture at the lowest temperature(T_(100)=350°C).Whereas,for catalyst prepared using urea,T_(100)=362°C.On the other hand the conversion of CO-CH_4mixture over the catalyst synthesized by KOH limited to 97%even beyond 400°C.Further,the effect of higher calcination temperatures of 500 and600°C was examined for the best catalyst.The total oxidation of the mixture was attained at higher temperatures of 375 and 410°C over catalysts calcined at 500 and 600°C respectively.Thus,the best precipitant established was Na_2CO_3and the optimum calcination temperature of 400°C was found to synthesize the Ni Co_2O_4catalyst for the best performance in CO-CH_4oxidation.     

Effects of synthesis methods on the performance of Pt + Rh/Ce0.6Zr0.4O2 three-way catalysts

The 0.7 wt% Pt + 0.3 wt% Rh/Ce0.6Zr0.4O2 catalysts were fabricated via different methods, including ultrasonic-assisted membrane reduction(UAMR) co-precipitation, UAMR separation precipitation, co-impregnation, and sequential impregnation. The catalysts were physico-chemically characterized by N2 adsorption, XRD, TEM, and H2-TPR techniques, and evaluated for three-way catalytic activities with simulated automobile exhaust. UAMR co-precipitation- and UAMR separation precipitationprepared catalysts exhibited a high surface area and metal dispersion, wide λ window and excellent conversion for NOx reduction under lean conditions. Both fresh and aged catalysts from UAMRprecipitation showed the high surface areas of ca. 60–67 m2/g and 18–22 m2/g, respectively, high metal dispersion of 41%–55%, and small active particle diameters of 2.1–2.7 nm. When these catalysts were aged, the catalysts prepared by the UAMR method exhibited a wider working window(Δλ = 0.284–0.287) than impregnated ones(Δλ = 0.065–0.115) as well as excellent three-way catalytic performance, and showed lower T50(169.C) and T90(195.C) for NO reduction than the aged catalysts from impregnation processes, which were at 265 and 309.C, respectively. This implied that the UAMR-separation precipitation has important potential for industrial applications to improve catalytic performance and thermal stability. The fresh and aged 0.7 wt% Pt + 0.3 wt% Rh/Ce0:6Zr0:4O2 catalysts prepared by the UAMR-separation precipitation method exhibited better catalytic performance than the corresponding catalysts prepared by conventional impregnation routes.     

CuO/ZSM-5系列催化剂的脱硫脱硝性能研究

采用浸渍法制备了不同质量分数的催化剂x％ CuO/ZSM-5 (x =2、4、6、8、10、12、50),并考察了其在CH4为还原剂条件下的脱硫脱硝性能.同时,采用X射线衍射(XRD)、H2-程序升温还原(H2-TPR)、NH3-程序升温脱附(NH3-TPD)、比表面积(BET)、扫描电子显微镜与能谱分析(SEM-EDS)等测试手段对催化剂进行表征.实验结果表明:10％ CuO/ZSM-5催化剂的活性组分具有较好的晶型结构,且高度分散在ZSM-5骨架中.在CH4+NO+ SO2反应中,10％ CuO/ZSM-5催化剂具有最好的脱硫脱硝活性,最高脱硫率和脱硝率分别为97.4％和94.6％.     

Efficient degradation of chlorobenzene in a non-thermal plasma catalytic reactor supported on CeO2/HZSM-5 catalysts

Chlorobenzene removal was investigated in a non-thermal plasma reactor using CeO₂/HZSM-5 catalysts. The performance of catalysts was evaluated in terms of removal and energy efficiency. The decomposition products of chlorobenzene were analyzed. The results show that CeO₂/HZSM-5 exhibited a good catalytic activity, which resulted in enhancements of chlorobenzene removal, energy efficiency, and the formation of lower amounts of by-products. With regards to CO₂ selectivity, the presence of catalysts favors the oxidation of by-products, leading to a higher CO₂ selectivity. With respect to ozone, which is considered as an unavoidable by-product in air plasma reactors, a noticeable decrease in its concentration was observed in the presence of catalysts. Furthermore, the stability of the catalyst was investigated by analyzing the evolution of conversion in time. The experiment results indicated that CeO₂/HZSM-5 catalysts have excellent stability: chlorobenzene conversion only decreased from 78% to 60% after 75 hr, which means that the CeO₂/HZSM-5 suffered a slight deactivation. Some organic compounds and chlorinated intermediates were adsorbed or deposited on the catalysts surface as shown by the results of Fourier Transform Infrared (FT-IR) spectroscopy, scanning electron microscope (SEM) and energy dispersive X-ray spectroscopy (EDS) analyses of the catalyst before and after the reaction, revealing the cause of catalyst deactivation.     

CuO对贵金属/CeO2/Al2O3催化剂的作用

制备含少量贵金属Ｐｔ、Ｐｄ的不同Ｃｕ和Ｃｅ摩尔含量比（０：１０,１：９,２：８）的催化剂,实验条件十加入ＣｕＯ可以提高Ｐｔ催化剂的二效活性;加入Ｃｕ：Ｃｅ＝２：８的ＣｕＯ降低了Ｐｄ催化剂的顾效性能,然而Ｃｕ：Ｃｅ＝１：９时可以改善Ｐｄ催化剂的三效催化性能。通过结构分析,认为ＣｕＯ的存在可以提高ｄ催化剂的比表面积,ＰｄＯ的分散度。     

SO2气氛下Cu-Ce-O催化剂氧化柴油车排气碳烟的性能

运用程序升温氧化(TPO)对共沉淀法合成的Cu-Ce-O催化剂进行了活性评价,考察了在不同浓度的S0,气氛下cu-Ce-O催化剂氧化模拟碳黑的性能,并用BET、XRD、TPR和FT-IR对催化剂进行了表征.BET和XRD测试显示,cu和ce的结合使催化剂比表面积增大,晶体结构发生变化,形成了复合氧化物;TPO活性测试结果表明,Cu-Ce-O复合催化剂比单一组分的CuO或CeO2具有更好的低温催化活性.复合氧化物cu-Ce-O中Cu原子含量越高,对应硫化后的催化剂氧化碳烟的能力越低,同时催化剂表面生成的硫酸盐越多,即催化剂抗硫中毒能力也降低.浓度低于0.03%的SO2对Cu-Ce-O的催化性能有一定的促进作用,但SO2的体积分数超过0.03%后碳黑燃烧速率变慢;FT-IR初步证实了高体积分数的SO2所产生的大量SO24-可能是抑制催化剂活性的原因.     

Sorbents with high efficiency for CO2 capture based on amines-supported carbon for biogas upgrading

Sorbents for CO_2 capture have been prepared by wet impregnation of a commercial active carbon(Ketjen-black, Akzo Nobel) with two CO_2-philic compounds, polyethylenimine(PEI)and tetraethylenepentamine(TEPA), respectively. The effects of amine amount(from 10 to70 wt.%), CO_2 concentration in the feed, sorption temperature and gas hourly space velocity on the CO_2 capture performance have been investigated. The sorption capacity has been evaluated using the breakthrough method, with a fixed bed reactor equipped with on line gas chromatograph. The samples have been characterized by N_2 adsorption–desorption,scanning electron microscopy and energy dispersive X-ray(SEM/EDX). A promising CO_2 sorption capacity of 6.90 mmol/gsorbenthas been obtained with 70 wt.% of supported TEPA at 70℃ under a stream containing 80 vol% of CO_2. Sorption tests, carried out with simulated biogas compositions(CH_4/CO_2mixtures), have revealed an appreciable CO_2 separation selectivity; stable performance was maintained for 20 adsorption–desorption cycles.     

不同硅铝比Fe-ZSM-5催化剂对氧化亚氮催化分解性能的研究

以不同硅铝比的H-ZSM-5分子筛为载体,采用离子交换法和化学气相沉积法制备Fe-ZSM-5催化剂,并用XRD、BET、TEM、UV-vis和NH3-TPD等表征手段对催化剂进行分析,研究催化剂中铁的存在状态.结果表明,分子筛的硅铝比影响铁在分子筛中的分布形态,化学气相沉积法和热离子交换法制得硅铝比为25的Fe-ZSM-5-25分子筛催化剂上均匀地分布着粒径为8 nm左右的纳米氧化铁颗粒,并且Fe-ZSM-5-25分子筛催化剂比Fe-ZSM-5-300更容易形成Fe3+x O y团簇.制得的Fe-ZSM-5分子筛催化剂催化分解氧化亚氮(N2O),结果表明,相同的制备方法,硅铝比小的Fe-ZSM-5-25催化剂对N2O分解活性更好;相同硅铝比的Fe-ZSM-5催化剂,采用化学气相沉积法制得的对N2O分解活性最好.另外,O2的存在对Fe-ZSM-5上N2O催化分解活性有抑制作用,而NO对N2O催化分解活性展示了一定的正效应.最后,经过100 h的连续反应,Fe-ZSM-5催化剂依然能够保持催化活性.     

Effect of MoO3 on vanadium based catalysts for the selective catalytic reduction of NOx with NH3 at low temperature

The selective catalytic reduction(SCR) activities of the MoO_3 doped V/WTi catalysts prepared by the incipient wetness impregnation method at low temperature were investigated.The results showed that the addition of MoO_3 could enhance the NO_ xconversion at low temperature and the best SCR activity was obtained when the dosage of MoO_3 reached5 wt.%. The NH3-TPD and DRIFTS experiments indicated that the addition of MoO_3 changed the type and number of acid sites on the surface of catalysts and reaction activities of acid sites were altered at the same time. The redox capacity and amount of active oxygen species got improved for V3Mo5/WTi catalyst, which could be confirmed by the H_2-TPR and transient response experiments. Water vapor inhibited the NO_xconversion at low temperature. Deposition of ammonium sulfate or bisulfate might be main reason for the loss of catalytic activity in the presence of SO_2 at low temperature. Choosing the suitable NH_3/NO ratio and elevation of reaction temperature both could weaken the influence of SO_2 on the SCR activity of the V3Mo5/WTi catalyst. Thermal treatment of the deactivated catalyst at350°C could get the low temperature activity recovered. The decrease of GHSV improved the de NO_x efficiency at low temperature and we speculated that the rational technological process and operation parameters could contribute to the application of this kind of catalysts in real industrial environment.     

Mo-modified Pd/Al2O3 catalysts for benzene catalytic combustion

Mo-modified Pd/Al2O3catalysts were prepared by an impregnation method and tested for the catalytic combustion of benzene. The catalysts were characterized by N2 isothermal adsorption, X-ray diffraction（XRD）, X-ray photoelectron spectroscopy（XPS）, temperatureprogrammed desorption of NH3（NH3-TPD）, H2temperature-programmed reduction（H2-TPR）, and high-angle annular dark-field scanning transmission electron microscopy（HAADF-STEM）. The results showed that the addition of Mo effectively improved the activity and stability of the Pd/Al2O3catalyst by increasing the dispersion of Pd active components, changing the partial oxidation state of palladium and increasing the oxygen species concentration on the surface of catalyst. In the case of the Pd-Mo/Al2O3catalyst,benzene conversion of 90% was obtained at temperatures as low as 190°C, which was 45°C lower than that for similar performance with the Pd/Al2O3catalyst. Moreover, the 1.0% Pd-5% Mo/Al2O3catalyst was more active than the 2.0% Pd/Al2O3catalyst. It was concluded that Pd and Mo have a synergistic effect in benzene catalytic combustion.     

OMS-2负载Pt催化剂的制备及其催化氧化性能研究

采用前掺杂法、沉积-沉淀法和浸渍法制备了氧化锰八面体分子筛(OMS-2)负载Pt催化剂(Pt/OMS-2),对所制催化剂进行了结构和织构表征。并研究了不同制备方法和沉积-沉淀法中不同制备(Pt负载量和溶液的pH值)对Pt/OMS-2催化氧化CO性能的影响。结果表明,沉积-沉淀法制备的Pt/OMS-2-DP催化剂活性最好(T100=100℃)。这与Pt/OMS-2-DP催化剂中Pt颗粒大小及OMS-2载体与Pt之间存在强相互作用有关。Pt负载量明显影响Pt/OMS-2-DP催化剂的催化活性,3Pt/OMS-2-DP催化剂(Pt=3.0 wt%)催化活性最高,这是由于适当Pt负载量,Pt颗粒较小,并与载体OMS-2的相互作用较强,能较好地活化OMS-2晶格氧。pH值对Pt/OMS-2-DP催化剂催化性能影响较大,这与OMS-2的等电点和Pt在不同溶液中存在不同Pt配位体形式有关。     

Selective catalytic reduction of nitrogen oxides over a modified silicoaluminophosphate commercial zeolite

Nitrogen oxides(NO_x:NO,NO_2)are a concern due to their adverse health effects.Diesel engine transport sector is the major emitter of NO_x.The regulations have been strengthened and to comply with them,one of the two methods commonly used is the selective catalytic reduction of NO_xby NH_3(NH_3-SCR),NH_3being supplied by the in-situ hydrolysis of urea.Efficiency and durability of the catalyst for this process are highly required.Durability is evaluated by hydrothermal treatment of the catalysts at temperature above 800°C.In this study,very active catalysts for the NH_3-SCR of NO_xwere prepared by using a silicoaluminophosphate commercial zeolite as copper host structure.Characterizations by X-ray diffraction(XRD),scanning electron microscopy(SEM)and temperature programmed desorption of ammonia(NH_3-TPD)showed that this commercial zeolite was hydrothermally stable up to 850°C and,was able to retain some structural properties up to950°C.After hydrothermal treatment at 850°C,the NO_xreduction efficiency into NH_3-SCR depends on the copper content.The catalyst with a copper content of 1.25 wt.%was the most active.The difference in activity was much more important when using NO than the fast NO/NO_2reaction mixture.     

Low-temperature VOCs oxidation performance of Pt/zeolites catalysts with hierarchical pore structure

Different zeolites supported Pt catalysts with micro-mesoporous structure were prepared by organic base tetrapropylammonium hydroxide (TPAOH) treatment and their catalytic oxidation activity for various volatile organic compounds (VOCs) were evaluated. The results reveal that the synergistic effect between Pt nanoparticles and surface acid sites plays an important role in VOCs low-temperature removal. The small size and high dispersion of Pt nanoparticles on the surface of the zeolites would promote the catalytic oxidation of aromatics and alkanes over the Pt/zeolite catalysts, while strong acidity and abundant acid sites of catalysts are in favour of the oxidation of the VOCs containing N and O heteroatoms. In addition, it was found that Pt/ZSM-5 catalyst exhibits the highest oxidation activity for various VOCs low-temperature removal amongst all the catalysts due to the balance of both Pt dispersion and abundant acid sites in the catalyst. This comprehensive consideration should be very helpful when designing and preparing novel catalysts for the low-temperature removal of VOCs.     

Decomposition of hexachlorobenzene over Al2O3 supported metal oxide catalysts

Decomposition of hexachlorobenzene (HCB) was investigated over several metal oxides (i.e., MgO, CaO, BaO, La₂O₃, CeO₂, MnO₂, Fe₂O₃, and Co₃O₄) supported on Al₂O₃, which was achieved in closed system at a temperature of 300°C. Catalysts were prepared by incipient wetness impregnation with different metal oxides loading and impregnating solvents. The decomposition efficiency of different catalysts for this reaction depends on the nature of the metal oxide used, and Al₂O₃ supported La₂O₃ was found to be the most active one. Pentachlorobenzene (PeCB), and all tetrachlorobenzene (TeCB), trichlorobenzene (TrCB), and dichlorobenzene (DCB) isomers were detected after the decomposition reaction, indicating that the decomposition was mainly a dechlorination process. The detection of all lower chlorinated benzenes suggested the complexity of decomposition and the presence of more than one dechlorination pathway.