不同粒径活性氧化铝负载CeO_2-Fe_2O_3催化还原脱硫脱硝

运用工业级活性氧化铝作载体,开展CeO2掺杂对不同粒径活性氧化铝负载Fe2O3催化还原烟气脱硫脱硝实验研究。并采用BET和XRD分别对氧化铝载体和催化剂进行表征。实验结果表明:比表面积和孔容相近的不同粒径活性氧化铝载体负载活性组分后,催化还原同时脱硫脱硝的活性表现出粒径较大的铝基催化剂,比粒径较小的铝基催化剂脱硫效果好;不同组分CeO2掺杂10%Fe2O3/Al2O3催化剂中,3mm粒径6%CeO2-10%Fe2O3/Al2O3催化剂脱硫效果最好;将此种催化剂用于模拟烟气(SO2+NO+CO+N2)脱硫脱硝研究,获得较宽的脱硫脱硝温度范围(300~550℃),且NO和SO2转化率均大于92.5%。     

锰铈脱硝催化剂的制备及其再生性能研究

采用等体积浸渍法制备了一系列Mn-Ce-Ox复合氧化物脱硝催化剂用于NH3选择性催化还原(NH3-SCR)NO。考察了Mn/Ce摩尔比、焙烧温度、H2O和SO2对Mn-Ce-Ox复合氧化物脱硝催化剂活性的影响及催化剂中毒再生性能。结果表明:当NH3:NO=1:1,空速为5 000 h-1,550℃焙烧制得的Mn/Ce摩尔比为5∶1的Mn-Ce-Ox复合脱硝催化剂活性最佳,活性温度窗口为100~260℃,在此温度区间内催化剂活性大于90%。200℃时,Mn-Ce-Ox复合催化剂活性最高为97.84%;在10%(V/V)H2O蒸汽和300×10-6SO2共存条件下,200℃时,催化剂活性在开始反应2.5 h内迅速下降至53%左右,并在之后的6 h内没有明显变化;中毒催化剂经常温水洗再生处理、质量分数为3%的硝酸溶液再生处理和550℃焙烧2 h再生处理后200℃活性均能恢复到90%以上,其中中毒催化剂经质量分数为3%硝酸处理后活性恢复率最高。     

V_2O_5/TiO_2催化剂用于烟气同时脱硫脱硝的研究

研究了用V2O5/TiO2催化剂同时脱除烟气中的SO2和NO,考察了H2还原温度及其它反应条件对SO2和NO脱除率的影响。结果表明,经H2还原后所制得的V2O5/TiO2催化剂可以提高脱硫脱硝活性,最佳还原温度为700℃;在450～500℃的烟气温度范围内,该催化剂有较佳的脱硫脱硝活性;在相同反应温度下,空速越大,SO2和NO的脱除率越低;烟气中的氧气可大大提高V2O5/TiO2的脱硫脱硝活性,且氧气体积含量在5%～10%范围内变化时,对SO2和NO脱除率的影响较小。     

废弃SCR脱硝催化剂的再生及其脱硝性能研究

对废弃脱硝催化剂处理后重新加工再生,研究了添加剂对其粉体成型和再生催化剂脱硝活性的影响,探讨了反应温度、空速、n(NH3)∶n(NO)摩尔比、氧含量、H2O和SO2对再生催化剂NH3选择性催化还原(SCR)NO的影响。结果表明:最佳再生条件是使用5%羧甲基纤维素和10%无机粘结剂辅助成型;废弃催化剂再生利用率高达90%;再生催化剂抗压强度为4.73 MPa,优于商用催化剂;空速5 000 h-1、氨氮摩尔比1、氧含量6%时,脱硝活性温度窗口为310⁴50℃,350℃时活性最高为94%;350℃时,单独通入1 000×10-6SO2或10%H2O对再生催化剂活性均有一定抑制作用,最低活性分别为70%和81%,停止通入SO2或H2O后其活性逐渐恢复;同时通入1 000×10-6SO2和10%H2O,再生催化剂活性下降至63%并于1 h内保持相对稳定,停止通入SO2和H2O 2 h后,活性逐渐恢复到73%。     

单斜相纳米氧化锆基低温SCR催化剂脱硝机制研究

以纳米m-ZrO2为载体,用浸渍法制备出MnOx-CeO2/m-ZrO2催化剂,考察反应温度、活性组分负载量对催化剂NH3-SCR脱硝活性影响,探讨催化剂表面织构特征,分析催化剂脱硝活性机制.结果表明,在低温脱硝温度范围,提高反应温度、增加活性组分负载量,有利于催化剂脱硝效率的增加.110℃时,2.5%MnOx-CeO2/m-ZrO2脱硝效率为55.5%,15%MnOxCeO2/m-ZrO2脱硝效率达93.5%.XRD、BET、XPS、H2-TPR表征结果表明,催化剂表面具有良好的氧化还原能力,表面织构对脱硝反应有利.NH3-TPD测试显示,MnOx-CeO2/m-ZrO2催化剂的脱硝反应机制为:NH3吸附在催化剂表面的Lewis酸性位和Brnsted酸性位上,通过反应生成相应中间产物NH2NO或NH4NO2,中间产物进一步分解最终转变为N2和H2O;催化剂总脱硝反应效率中,在Lewis酸性位上的脱硝反应占比较大.     

不同载体对Cu基脱硝催化剂性能的影响研究

文章以TiO₂、ZSM-5和SSZ-39为载体制备了Cu基脱硝催化剂,采用XRD、N₂-吸附脱附、H₂-TPR、XPS、NH₃-TPD、NH₃-DRIFTS等表征手段分析催化剂的物理化学性质,通过固定床微型反应器对比3种催化剂的脱硝活性,并考察了Cu/SSZ-39催化剂的抗SO₂、H₂O性能。结果表明：Cu/TiO₂催化剂的比表面积低、活性组分含量少、O_α/(O_α+O_β)比率低、酸量和酸强低,导致该催化剂的脱硝活性较差。以分子筛为载体所制备的催化剂(Cu/ZSM-5和Cu/SSZ-39),体现了更好的脱硝活性。其中,Cu/SSZ-39催化剂的还原性能和酸量相对较高,催化剂的脱硝活性优于Cu/ZSM-5催化剂。此外,Cu/SSZ-39催化剂还体现了较好的稳定性,在含SO₂、H₂O气氛下,连续运行60 h,脱...     

Pd/ZrO【sub】2【/sub】-Al【sub】2【/sub】O【sub】3【/sub】催化剂加氢脱硫性能的研究

采用等体积浸渍法制备了一系列不同Zr含量的ZrO2-Al2O3复合载体和Pd/ZrO2-Al2O3催化剂,利用连续流动微反装置考察了Pd/ZrO2-Al2O3催化剂的噻吩加氢脱硫(HDS)性能,并运用程序升温还原(TPR),程序升温脱附(H2-TPD,NH3-TPD)和N2物理吸附等技术对载体及催化剂进行了表征.结果表明:ZrO2-Al2O3复合载体中Zr含量对Pd基催化剂的HDS性能有较大影响,加入适量Zr可增大Pd/Al2O3催化剂的分散度及H2吸附量和酸量,减弱活性组分与载体的相互作用,使活性中心和噻吩吸附位增多以及活化能降低,从而有利于Pd基催化剂HDS反应活性的提高,w(Zr)为9%时Pd/ZrO2-Al2O3催化剂的活性最好.     

O2+、O3同时脱硫脱硝实验

针对目前的烟气同时脱硫脱硝方法中存在的投资成本、运行费用、占地面积大等问题,研究强电离放电方法产生高浓度氧活性粒子(O2+、O3)注入烟气外排管道中,进行O2+、O3消除烟气中的NO, SO2转化成HNO3, H2SO4的等离子化学反应.描述强电离介质阻挡放电制取O2+、O3原理和烟道中O2+与H2O反应形成·OH及其氧化脱硫脱硝反应机制,分析回收酸液中的酸根离子种类及浓度.在O2+、O3与NO+SO2的物质的量比为5,烟气温度为65℃,H2O体积浓度为10%,停留时间为1s的实验条件下,脱硝脱硫率分别为97.4%,83.2%.     

Ag/Al2O3催化剂用于碳氢化合物选择性还原NO

比较了富氧条件下CH4、C3H8、C3H6和C2H5OH分别用作还原剂时,NO在Ag/Al2O3催化剂上的还原活性.结果表明, CH4和C3H8还原NO的活性很低,而C3H6和C2H5OH能有效地还原NO.在此基础上,研究了H2O和SO2对C3H6和C2H5OH在Ag/Al2O3催化剂上还原NO活性的影响.结果表明,H2O的存在会降低低温区的NO还原活性,而且这种影响是可逆的.将H2O 和SO2同时加入反应混合气,引起NO还原活性较大幅度降低,结合程序升温脱附实验结果,认为可能是由于存在SO2时,Ag/Al2O3催化剂吸附NO的能力降低.     

O_2~+、O_3同时脱硫脱硝实验

针对目前的烟气同时脱硫脱硝方法中存在的投资成本、运行费用、占地面积大等问题,研究强电离放电方法产生高浓度氧活性粒子(O2+、O3)注入烟气外排管道中,进行O2+、O3消除烟气中的NO,SO2转化成HNO3,H2SO4的等离子化学反应.描述强电离介质阻挡放电制取O2+、O3原理和烟道中O2+与H2O反应形成·OH及其氧化脱硫脱硝反应机制,分析回收酸液中的酸根离子种类及浓度.在O2+、O3与NO+SO2的物质的量比为5,烟气温度为65℃,H2O体积浓度为10%,停留时间为1s的实验条件下,脱硝脱硫率分别为97.4%,83.2%.     

Coupling mechanism of activated carbon mixed with dust for flue gas desulfurization and denitrification

To clarify the effect of coking dust, sintering dust and fly ash on the activity of activated carbon for various industrial flue gas desulfurization and denitrification, the coupling mechanism of the mixed activated carbon and dust was investigated to provide theoretical reference for the stable operation. The results show that coking dust had 34% desulfurization efficiency and 10% denitrification efficiency; correspondingly, sintering dust and fly ash had no obvious desulfurization and denitrification activities. For the mixture of activated carbon and dust, the coking dust reduced the desulfurization and denitrification efficiencies by blocking the pores of activated carbon, and its inhibiting effect on activated carbon was larger than its own desulfurization and denitrification activity. The sintering dust also reduced the desulfurization efficiency on the activated carbon while enhancing the denitrification efficiency. Fly ash blocked the pores of activated carbon and reduced its reaction activity. The reaction activity of coking dust mainly came from the surface functional groups, similar to that of activated carbon. The reaction activity of sintering dust mainly came from the oxidative property of Fe₂O₃, which oxidized NO to NO₂ and promoted the fast selectively catalytic reduction (SCR) of NO to form N₂. Sintering dust was activated by the joint action of activated carbon, and both had a coupling function. Sintering dust enhanced the adsorption and oxidation of NO, and activated carbon further promoted the reduction of NO_x by NH₃; thus, the denitrification efficiency increased by 5%-7% on the activated carbon.     

Synergistic effect of Pt nanoparticles and micro-mesoporous ZSM-5 in VOCs low-temperature removal

Micro-mesoporous ZSM-5 zeolites were obtained by the post-treatment of tetrahydroxy ammonium hydroxide (TPAOH) solution with different concentration. The hierarchical pore structure formed during the desilication process facilitates the dispersion of Pt nanoparticles and Pt/ZSM-5 catalysts exhibit rather high catalytic activity for the deep oxidation of various VOCs at low temperature. The catalyst treated with TPAOH of 0.1 mol/L (Pt/ZSM-5(0.1)) shows the lowest degradation temperature (T_90%) of 128 and 142°C, respectively for benzene and n-hexane. Compared with the untreated Pt/ZSM-5 catalyst, the abundant mesopores, small Pt particle size and finely dispersed Pt contribute to the superior catalytic activity and stability of the Pt/ZSM-5 catalysts for VOCs removal. More importantly, the existence of H₂O in the feed gases hardly affected the activity of Pt/ZSM-5(0.1) catalyst at the low reaction temperature of 128°C, which is very important for VOCs low-temperature removal in the future practical applications.     

硅铝比和NiO对ZSM-5协同低温等离子体降解甲苯的影响

研究了不同硅铝比的ZSM-5与Ni/ZSM-5分子筛协同低温等离子体技术对甲苯降解性能的影响.以Ni O(Nickel Oxide)为活性组分,采用浸渍法对ZSM-5分子筛进行改性,利用氮气吸附脱附(BET)、X射线衍射仪(XRD)、X射线光电子能谱分析(XPS)、H_2程序升温还原(H_2-TPR)、NH_3程序升温脱附(NH_3-TPD)、Toluene程序升温脱附(Toluene-TPD)等技术表征样品的物理化学性质.考察了硅铝比对ZSM-5与Ni/ZSM-5分子筛体系中甲苯的吸附性能,研究了不同放电电压下硅铝比对甲苯降解率、碳平衡及二氧化碳选择性的影响,并采用气相色谱-质谱联用仪(GC-MS)分析了催化剂表面的有机产物.结果表明:硅铝比不但影响分子筛本身的物理化学特性(比表面积、氧化还原性能、表面酸性、疏水性等),还会影响Ni的负载形态和方式,更高的硅铝比与Ni O的负载能促进甲苯深度氧化,减少副产物,提高碳平衡和二氧化碳选择性.     

Cu/Al2O3低温催化氧化H2S研究

高效低成本的催化剂是低温催化氧化脱除硫化氢（H₂S）的研究重点,采用浸渍法研制了Cu/Al₂O₃催化剂,利用N₂物理吸附、XRD（X射线衍射分析）、XPS（光电子能谱）、FT-IR（傅里叶变换红外光谱）等表征手段了解催化剂的表面结构和物相结构,并开展不同温度、相对湿度、Cu负载量条件下的H₂S动态脱附以考察催化剂脱硫性能.结果表明:①催化剂是一种典型的介孔材料,且CuO和Cu₂O高度分散在催化剂表面.②FT-IR结果表明,催化剂在H₂S催化氧化过程中表面Cu_xO和表面结合水中的羟基均参与反应,且有SO₄2-的生成.③XRD、XPS结果表明,脱硫过程中有S单质和CuS的生成.④适宜的温度（50℃）和相对湿度（50%）会显著增强Cu基催化剂的脱硫性能.⑤负载量为3%的Cu基催化剂具有最佳的脱硫性能,穿透硫容量高达220.92 mg/g.研究显示,利用浸渍法可以合成低温催化氧化H₂S的高硫容Cu基催化剂.      

不同光源下TiO2/ACF同时脱硫脱硝实验研究

实验室制备了负载型二氧化钛光催化剂TiO₂/ACF,利用自行设计的光催化反应器,在紫外和可见2种光源下进行了同时脱硫脱硝试验,确定了最佳的试验条件,比较了2种不同光源下的脱除效率.结果表明,烟气中氧含量、反应温度、烟气含湿量、光照强度等是影响光催化的主要因素,在紫外光源的照射下,负载型TiO₂/ACF光催化剂脱除SO₂和NO的效率分别达到99.7%和64.3%,在可见光源的照射下,负载型TiO₂/ACF光催化剂脱除SO₂和NO的效率分别达到97.5%和49.6%, 5次平行试验结果表明,平行数据的标准偏差S较小.通过反应后吸收液的离子色谱分析,推测了2种不同光源下同时脱硫脱硝的反应机制.     

废水同步脱硫脱氮关键工艺参数及微生物群落结构的研究

大量未经处理的含硫化物和硝酸盐废水的排放将带来严重的环境问题.根据以废治废原则,使用厌氧滴滤塔反应器构建的同步脱硫耦联反硝化脱氮反应(SDD)能很好的去除废水中S~(2-)和NO-x-N.其中以聚氨酯泡沫为填料的厌氧滴滤塔反应器中生物活性最强,脱氮脱硫效果最好.体系中功能菌优先将S~(2-)氧化成S0,待S~(2-)去除完全后,再进一步将S0氧化成SO_4~(2-).同时,SDD反应降解NO_3~--N的速率快于NO_2~--N.进水S/N摩尔比越大,产物中SO_4~(2-)相对含量越低.结合实际工程考虑,应控制进水S/N摩尔比在5/3~5/2之间,S~(2-)浓度控制在538 mg·L-1以下.微生物群落结构分析结果表明,Thiobacillus属在4组反应器上占绝对优势,其相对丰度均高于40%.其次相对丰度较高的Rhodanobacter、Arenimonas和Truepera属与厌氧反硝化作用密切相关.对4组反应器中微生物进行Alpha-多样性分析结果表明取得较好脱硫耦联反硝化效果的体系中物种多样性指数也较高.     

碳源对反硝化细菌的反硝化速率和群落结构的影响

为探究碳源类型在反硝化过程中对氮素转化和微生物群落组成的影响,分别建立R1（以C₆H₁₂O₆为碳源）和R2（以CH₃COONa为碳源）反应器,通过分析R1和R2反应器中反硝化过程的氮素转化情况,评价C₆H₁₂O₆和CH₃COONa对脱氮效果的影响,并运用动力学模型对R1和R2反应器中反硝化能力进行评价;同时,采用高通量测序技术表征2种碳源对反应器中微生物群落结构和多样性的影响.结果表明:①运行后期的R1、R2反应器中单位生物量的反硝化速率（以NO₃--N计,下同）分别为8.56、11.26 mg/（g·h）,R1反应器中NO₂--N累积平均值为11.34 mg/L,显著高于R2反应器（0.20 mg/L）,且R1反应器中NH₄+-N累积平均值为6.58 mg/L,是R2反应器（0.65 mg/L）的10.11倍.②反应器中NO₃--N还原过程均符合Haldane模型,其中R1、R2反应器中单位生物量的r_max（最大降解速率）分别为35.61、47.79 mg/（g·h）,表明R2反应器中的反硝化能力强于R1反应器.③微生物经过富集后,其细菌多样性和物种丰度下降,但发挥反硝化作用的微生物相对丰度逐渐增加.R1和R2反应器中共同的优势菌门有Proteobacterias、Bacteroidetes、Firmicutes和Gracilibacters,其在R1反应器中的相对丰度依次为96.14%、2.06%、0.66%和0.47%,在R2反应器中依次为79.75%、6.88%、9.47%和2.13%,优势菌门在不同运行时间的丰度表达上存在消长变化状态.研究显示,C₆H₁₂O₆和CH₃COONa在反硝化过程的氮素转化上存在明显差异,对各类优势菌群的相对丰度有明显影响.      

Metal loaded zeolite adsorbents for hydrogen cyanide removal

Metal(Cu,Co,or Zn) loaded ZSM-5 and Y zeolite adsorbents were prepared for the adsorption of hydrogen cyanide(HCN) toxic gas.The results showed that the HCN breakthrough capacity was enhanced significantly when zeolites were loaded with Cu.The physical and chemical properties of the adsorbents that influence the HCN adsorption capacity were analyzed.The maximal HCN breakthrough capacities were about the same for both zeolites at 2.2 mol of HCN/mol of Cu.The Cu2p XPS spectra showed that the possible species present were Cu2O and CuO.The N1s XPS data and FT-IR spectra indicated that CNwould be formed in the presence of Cu+/Cu2+ and oxygen gas,and the reaction product could be adsorbed onto Cu/ZSM-5 zeolite more easily than HCN.     

Study on methane conversion to syngas over nano Pt-CeO2-ZrO2/MgO catalysts: Structure and catalytic behavior of catalysts prepared by using ion exchange resin method

Nano Pt-Ce0₂-Zr0₂/MgO catalysts with 0.8 wt.% Pt, 3.0 wt.% Ce0₂ and 3.0 wt.% Zr0₂ were prepared by wet impregnation mothod. Support MgO was obtained using ion exchange resin method or using commercial MgO. S_BET, XRD, TEM and C0₂-TPD were used to characterize the supports and catalysts. CH₄-C0₂ reforming to synthesis gas was performed to test the catalytic behavior of the catalysts. The catalysts prepared using ion exchange resin exhibited more regular structure, more basic sites and higher stability of Pt and MgO than prepared from commercial MgO. At 1073 K, atmospheric pressure, and at high gas hourly space velocity of 36,000 mL/(g-hr) with a stoichiometric feed of CH₄ and C0₂, the catalyst supported on the MOH(GD)-IE showed a higher and more stable activity for CH₄-C0₂ reforming reaction than the catalyst prepared using commercial MgO. The characterisation results demonstrated that the high activity and stability of the catalyst stem from the high dispersion of Pt, the stable structure and the high resistance to carbon deposition on the catalyst.     

Effects of aeration method and aeration rate on greenhouse gas emissions during composting of pig feces in pilot scale

The aim of this study was to uncover ways to mitigate greenhouse gas(GHG) emissions and reduce energy consumption during the composting process. We assessed the effects of different aeration rates(0, 0.18, 0.36, and 0.54 L/(kg dry matter(dm)·min)) and methods(continuous and intermittent) on GHG emissions. Pig feces and corn stalks were mixed at a ratio of 7:1. The composting process lasted for 10 weeks, and the compost was turned approximately every 2 weeks. Results showed that both aeration rate and method significantly affected GHG emissions. Higher aeration rates increased NH3 and N2O losses,but reduced CH4 emissions. The exception is that the CH4 emission of the passive aeration treatment was lower than that of the low aeration rate treatment. Without forced aeration,the CH4 diffusion rates in the center of the piles were very low and part of the CH4 was oxidized in the surface layer. Intermittent aeration reduced NH3 and CH4 losses, but significantly increased N2 O production during the maturing periods. Intermittent aeration increased the nitrification/denitrification alternation and thus enhanced the N2 O production. Forced aeration treatments had higher GHG emission rates than the passive aeration treatment. Forced aeration accelerated the maturing process, but could not improve the quality of the end product. Compared with continuous aeration, intermittent aeration could increase the O2 supply efficiency and reduced the total GHG emission by 17.8%, and this reduction increased to 47.4% when composting was ended after 36 days.