2-丁烯醛生产废水中溶解性有机物的分级解析

采用超滤膜法将2-丁烯醛生产废水中的有机物分为相对分子质量不同的7个级分,并应用溶解性有机碳(dissolved organic carbon,DOC)、紫外吸收光谱(ultraviolet spectrum,UV)、傅里叶变换红外光谱(fourier transform infrared spectrometer,FT-IR)和气相色谱/质谱联用仪(gas chromatography with mass spectrometry,GC-MS)技术对不同相对分子质量区间的有机物所占比例及物质结构进行了研究.结果表明,废水中相对分子质量1×103的有机物所占比例最高,达到88.57%;采用GCMS对废水中相对分子质量1×103的级分进行分析,定性出27种化合物,包含醛、酮、酯、醇、酚、酸、烷烃类及其他苯系物等,其峰面积占有机物峰面积总和的比例分别为6.9%、5.3%、35.4%、13.2%、4.6%、0.4%、1.7%、16.8%,总和为84%.UV和FT-IR分析结果均显示不同相对分子质量区间的光谱吸收特征没有明显差别,级分中存在含有不饱和双键、羟基、羰基化合物及芳香族化合物,与GC-MS检测结果相吻合.研究结果为废水处理工艺的开发与优化提供了重要的指导作用.     

印染废水RO浓水水质分析

以江苏某印染废水处理厂反渗透（RO）浓水为研究对象,采用多种分析手段分析了RO浓水的水质特征.首先采用IC和ICP-MS对水中的无机离子进行了定性和定量分析,采用GC-MS对废水中的半挥发性有机物进行定性和定量分析.结果表明,RO浓水中无机离子以Na⁺、Cl^-和SO₄^2-为主,半挥发性有机物邻苯二甲酸二（2-乙基己）酯（DEHP）为主要成分,其浓度为1.452mg/L.为分析RO浓水中的溶解性有机物（DOM）特征,进一步采用超滤膜分子量分级法和树脂亲疏水分离技术对废水中的DOM进行分离解析,分析了不同组分的溶解性有机碳（DOC）、UV₂₅₄、SUVA含量和分布情况,应用三维荧光光谱对各组分物质进行了定性分析.超滤分级表明,RO浓水中相对分子量<1k的有机物占56.98%,相对分子质量5~10k有机物仅占2.19%,但其芳香化程度较高.树脂分离结果表明,RO浓水中亲水性物质（HPI^*）、疏水性物质（HPO^*）和过渡性物质（TPI^*）的DOC含量差异不大,其中HPO^*的芳香构造化程度最高,含有较多的色氨酸类芳香族蛋白质,而HPI^*中含有较多的溶解性微生物代谢产物类物质.     

造纸废水二级生化出水的电离辐射深度处理

探讨了采用电离辐射对造纸废水二级生化出水进行深度处理的可行性.结果表明,二级生化出水主要由相对分子质量为1000～3000和3000以上的有机物组成,它们对COD的贡献分别为69.5%和6.9%,它们对溶解性有机质（DOC）的贡献分别为40.6%和31.6%.电离辐射促使废水中的一些大分子有机物向小分子有机物转化,相对...     

印染生化尾水电解过程溶解性有机物变化特性

基于荧光激发发射矩阵（EEM）,结合紫外-可见吸收光谱（UV-vis）、红外光谱（IR）和气相色谱质谱联用仪（GC-MS）,精准分析印染生化尾水电解过程溶解性有机物（DOM）结构和组成,揭示宏观水质指标COD、BOD变化的本质.三维荧光光谱PARAFAC分析显示,印染生化尾水存在酪氨酸类（C1）、色氨酸类（C2）、腐植酸类（YC3）3个荧光组分.15mA/cm²电流密度下,经过一定时间电解（如30min）,原荧光强度开始逐渐减弱,C1、C2组分最大荧光强度（Fmax）变化不大,出现最大荧光强度（F_max）降低的DC3色氨酸类组分,废水B/C比从0.27提升至0.42,即尾水可生化性得到提升.进一步分析,电解过程,印染生化尾水DOM的C=C、C=O、C-N、C-O-C结构被降解,原水中烯烃、酮类、胺类、醇类、苯类、卤代烃、酯类等有机化合物被逐步降解为小分子有机酸、烷基酯、烷烃等,这是荧光团转变、可生化性提升的本质原因.三维荧光直观反映了电解过程DOM组成结构的特征光谱,为科学评估电解技术效果和后续印染生化尾水排放溯源提供支撑.     

腐蚀电池-Fenton处理渗滤液溶解性有机物光谱特征

为了研究垃圾渗滤液中溶解性有机物（DOM）在腐蚀电池-Fenton（CCF）深度处理过程中的去除特性,采用XAD-8和XAD-4树脂将DOM分成5种组分（亲水性有机物HPI、疏水性有机酸HPO-A、过渡亲水性有机酸TPI-A、疏水性中性有机物HPO-N、过渡亲水性中性有机物TPI-N）,并用紫外和荧光光谱对各组分的降解...     

稠油废水中溶解性有机物的分离和表征

利用XAD-8大孔吸附树脂将稠油废水中的溶解性有机物进行分离,对稠油废水DOM及各分离组分进行TOC、UV254、硬度、Ca2+、Mg2+浓度等的测定,并采用官能团滴定、红外光谱等分析方法对稠油废水进行表征。结果表明:稠油废水中DOM以包括腐殖酸和富里酸两部分物质的憎水部分为主,两者分别占总TOC的18.64%和43.58%,亲水部分仅占9.35%,同时还有一部分有机物未分离出;紫外吸光度结果表明,稠油废水及各组分的芳香化程度为:腐殖酸>富里酸>稠油废水>亲水部分;官能团滴定结果表明,各组分的总酸度大小为富里酸>腐殖酸>亲水部分;稠油废水中DOM及各组分的硬度和Ca2+、Mg2+分布分析结果表明,腐殖酸和富里酸均和Ca2+、Mg2+发生反应,由此可推断由于腐殖酸和富里酸与交换下来的Ca2+、Mg2+的吸附作用导致两者可能因此粘附在大孔弱酸树脂上,从而影响树脂正常运行;红外光谱分析结果与官能团滴定结果一致。     

北京市道路雨水径流溶解性有机物化学组分特性

为探究北京市道路雨水径流溶解性有机物（DOM）的化学特性,采用三维荧光光谱、紫外-可见吸收光谱及红外光谱技术,对北京市不同交通密度道路雨水径流溶解性有机物的化学组分进行分析.结果表明,北京市道路雨水径流DOM以疏水性组分为主,且主要为疏水中性组分.道路雨水径流DOM亲水性组分主要由类芳香蛋白物质组成,疏水性组分除含大量类芳香蛋白物质外,还含有大量类富里酸物质.道路雨水径流DOM疏水性组分的芳香化程度较高、腐殖化程度较低,亲水性组分与之相反.道路雨水径流DOM酸性组分中含异构化的羧基和苯环等官能团,碱性组分和中性组分中多含醚键、酯基、酚类和醇类等官能团.交通密度对道路雨水径流DOM化学组分的物质组成、特性等无明显影响,仅影响各化学组分中的物质含量;交通密度越大,各化学组分中物质的含量越多和芳香化程度越高,腐殖化程度越低.     

发酵制药废水二级出水中溶解性有机物特性分析

溶解性有机物（DOM）是发酵制药废水二级生化尾水深度处理工艺的主要去除对象,深入解析废水中DOM的特性是将其有效去除的前提和关键.本研究采集氨基酸类、头孢类、抗生素类、维生素类、阿维菌素类5种发酵制药废水二级出水,通过XAD-8树脂亲疏水性分离、凝胶色谱分子量分级、傅里叶变换红外光谱和三维荧光表征对二级出水中的DOM进行特性分析.结果表明,5种发酵制药废水二级出水的盐度和色度高,废水中有机物浓度高、波动大（48.60~245.40 mg·L^-1）.DOM大多数以疏水性组分为主,分子量分布广泛（210~10000 Da）.二级出水DOM均含有大量的不饱和双键、苯环结构,同时含有—OH、—NH₂和C=O等发色团和助色基团,造成废水色度较高.通过对发酵制药废水二级出水进行EEM-PARAFAC分析确定了4种荧光组分特征峰,包括3种腐殖质类（C1、C3、C4）和1种类蛋白类组分（C2）.发酵制药废水二级出水中DOM主要是以类腐殖质有机物为主（C1、C3）.全方面识别和解析发酵制药废水DOM的组成,可为废水深度处理工艺的优化提供指导.     

道路雨水径流溶解性有机物与重金属结合作用分析

为了解道路雨水径流溶解性有机物(DOM)与重金属的相互作用,采用荧光激发-发射矩阵光谱、超滤、离子选择电极法及红外光谱等技术对道路雨水径流溶解性有机物及其组分同Cu~(2+)、Pb~(2+)和Cd~(2+)的络合作用进行了研究.结果表明,道路雨水径流DOM与3种重金属离子的络合作用由强到弱依次是:Cu~(2+)Pb~(2+)Cd~(2+),4种分子量DOM组分与重金属之间均发生了络合反应,且DOM组分分子量越小,与重金属之间的络合作用越强.4个不同分子量区间的DOM组分与Cu~(2+)、Pb~(2+)和Cd~(2+)之间的络合作用由强到弱的顺序为:1 kDa组分、1~10 kDa组分、10~30kDa组分、30 kDa~0.45μm组分.     

保定府河DOM的光谱特征及其来源解析

府河是白洋淀入淀河流中的主要河流,研究府河溶解性有机物分布特征及污染来源对入淀河流的环境管理及水质改善具有重要意义。文章2021年12月对府河干流及支流20个采样点进行采样,通过紫外光谱与三维荧光光谱-平行因子分析技术分析府河水体溶解性有机物,并对溶解性有机物组分来源进行解析。研究发现,府河水体溶解性有机物组分中类腐殖质组分含量高于水体中类蛋白组分含量,且黄花沟中有机组分对府河水体影响较大;大量城市污水处理厂出水汇入府河后类蛋白占比增大,这可能是河内生物活性提升导致,故F9以后自生源贡献升高;荧光光谱分解得到4个组分,C1、C2（类腐殖质）占71.88%,C3、C4（类蛋白）占28.12%,府河干流溶解性有机物主要来源于外源污水厂出水输入、自生源生物类蛋白和陆源农田土壤等;荧光组分与溶解性有机碳、总氮、硝态氮有显著的正相关性,PC1与荧光组分呈现显著正相关。综上,通过对府河水体溶解性有机物荧光特征及来源解析,府河受陆源类腐殖质与生物自生源双重影响,这为府河水体的进一步管理提供了理论参考。     

石化污水厂二级出水溶解性有机物分级解析研究

以某石化污水处理厂二级出水为研究对象,采用大孔吸附树脂将污水中溶解性有机物分离成亲水性物质、疏水酸性物质、疏水中性物质和疏水碱性物质4个组分,分析了各组分的有机物的组成特征、三维荧光光谱特征及红外光谱特征.结果表明,亲水性物质和疏水酸性物质分别占水样中溶解性有机碳的49%和29%,是该石化污水厂二级出水中的主要物质类别.亲水性物质中含有较多的生物源腐殖质类物质,疏水中性物质含有较多的芳香族蛋白质和溶解性微生物代谢产物类物质.4种组分的红外光谱图中600~1200cm-1波数的指纹区波峰数量最多,多为芳香类同分异构体化合物.     

厌氧-缺氧-好氧处理出水中溶解性有机物组分的特征分析

本研究利用XAD-8大孔树脂对某城市污水处理厂的厌氧-缺氧-好氧(A2O)工艺出水中的溶解性有机物进行了组分分离,分析了各组分的溶解性有机碳(Dissolved organic carbon,DOC)、紫外-可见光谱和遗传毒性.结果表明,污水中亲水性物质和疏水酸性物质的DOC含量分别占总DOC含量的65%和24%.亲水性物质组分中的芳香族化合物含量显著高于其它组分,但是单位质量的亲水性物质、疏水酸性物质和疏水碱性物质中的芳香族化合物含量相近.污水具有一定的遗传毒性,主要遗传毒性物质为亲水性物质和疏水酸性物质,而疏水碱性物质和疏水中性物质则未检出遗传毒性.     

Improving biodegradation potential of domestic wastewater by manipulating the size distribution of organic matter

Carbon source is a critical constraint on nutrient removal in domestic wastewater treatment. However, the functions of particulate organic matter (POM) and some organics with high molecular weight (HMW) are overlooked in the conventional process, as they cannot be directly assimilated into cells during microbial metabolism. This further aggravates the problem of carbon source shortage and thus affects the effluent quality. Therefore, to better characterize organic matter (OM) based MW distribution, microfiltration/ultrafiltration/nanofiltration (MF/UF/NF) membranes were used in parallel to fractionate OM, which obtained seven fractions. Hydrolysis acidification (HA) was adopted to manipulate the MW distribution of dissolved organic matter (DOM) and further explore the correlation between molecular size and biodegradability. Results showed that HA pretreatment of wastewater not only promoted transformation from POM to DOM, but also boosted biodegradability. After 8 hr of HA, the concentration of dissolved organic carbon (DOC) increased by 65%, from the initial value of 20.25 to 33.48 mg/L, and the biodegradability index (BOD5 (biochemical oxygen demand)/SCOD (soluble chemical oxygen demand)) increased from 0.52 to 0.74. Using MW distribution analysis and composition optimization, a new understanding on the characteristics of organics in wastewater was obtained, which is of importance to solving low C/N wastewater treatment in engineering practice.     

Heavy metals in rice and garden vegetables and their potential health risks to inhabitants in the vicinity of an industrial zone in Jiangsu, China

Contamination of soil and agricultural products by heavy metals resulting from rapid industrial development has caused major concern. In this study, we investigated heavy metal (Cu, Zn, Pb, Cr, Hg and Cd) concentrations in rice and garden vegetables, as well as in cultivated soils, in a rural-industrial developed region in southern Jiangsu, China, and estimated the potential health risks of metals to the inhabitants via consumption of locally produced rice and garden vegetables. A questionnaire-based survey on dietary consumption rates of foodstuffs showed that rice and vegetables accounted for 64% of total foodstuffs consumed, and over 60% of rice and vegetables were grown in the local region. Average concentrations of Cr, Cu, Zn, Cd, Hg and Pb were 0.75, 2.64, 12.00, 0.014, 0.006 and 0.054 mg/kg dw (dry weight) in rice and were 0.67, 1.18, 4.34, 0.011, 0.002 and 0.058 mg/kg fw (fresh weight) in garden vegetables, respectively. These values were all below the maximum allowable concentration in food in China except for Cr in vegetables. Leafy vegetables had higher metal concentrations than solanaceae vegetables. Average daily intake of Cr, Cu, Zn, Cd, Hg and Pb through the consumption of rice and garden vegetables were 5.66, 16.90, 74.21, 0.10, 0.04 and 0.43 μg/(kg·day), respectively. Although Hazard Quotient values of individual metals were all lower than 1, when all six metal intakes via self-planted rice and garden vegetables were combined, the Hazard Index value was close to 1. Potential health risks from exposure to heavy metals in self-planted rice and garden vegetables need more attention.     

Effect of molecular weight of dissolved organic matter on toxicity and bioavailability of copper to lettuce

To clarify the e ects of molecular weight of dissolved organic matter (DOM) on the toxicity and bioavailability of copper (Cu) to plants, DOM extracted from chicken manure was ultra-filtered into four fractions according to their molecular weights by means of sequential-stage ultrafiltration technique. Lettuce seeds were germinated by being exposed to the solutions containing Cu2+ with or without di erent fractions of DOM. The concentration of copper in roots, leaves, sprouts and the length of roots were investigated. The results showed that not all fractions of DOM could improve copper availability or toxicity. The fraction of DOM with larger molecular weight more than 1 kDa had higher complexation stability with Cu2+ and caused lower concentration of free Cu2+ ion in the solution of copper plus the fraction, resulting in lower availability and toxicity of copper to lettuce, but the fraction with molecular weight less than 1 kDa had the opposite function. Therefore, the molecular weight of 1 kDa may be the division point to determine DOM to increase or decrease copper availability and toxicity.     

Fouling of nanofiltration membrane by effluent organic matter： Characterization using different organic fractions in wastewater

The UF membrane with molecular weight cutoff (MWCO) ranging from 2 kDa to 100 kDa and XAD-8 resin were employed to identify the characteristic of molecular weight (MW) distribution of wastewater effluent organic matter (EfOM) in terms of TOC and UV254, as well as the amounts of the hydrophilic/hydrophobic organic fractions in different MW ranges. Then, the nanofiltration (NF) membrane fouling experiments were carried out using the above fractionated water to investigate the effect of MW distribution and hydrophilic/hydrophobic characteristics of EfOM on the membrane flux decline using the fractionated water samples above. The experimental results have shown that 45.61% of the total organics belongs to the low MW one, among which the percentage of the hydrophilic organics with low MW (less than 2 kDa) was up to 28.07%, while that of the hydrophobic organics was 17.54%. In particular, the hydrophilic fraction was found to be the most abundant fraction in the effluents. MW distribution has a significant effect on the membrane fouling. When the MW was less than 30 kDa, the lower the MW, the larger was the specific flux decline, while in the case of MW higher than 30 kDa, the higher the MW, the larger was the specific flux decline, and the decline degree of low MW organics was larger than the high MW one. With the same MW distribution range, specific flux decline of the hydrophilic organic was considerably slower than that of the hydrophobic organic, which indicated that the hydrophobic organic fractions dominantly contribute to the flux decline.     

Fouling of nanofiltration membrane by e uent organic matter: Characterization using di erent organic fractions in wastewater

The UF membrane with molecular weight cuto (MWCO) ranging from 2 to 100 kDa and XAD-8 resin were employed to identify the characteristic of molecular weight (MW) distribution of wastewater e uent organic matter (EfOM) in terms of TOC and UV254, as well as the amounts of the hydrophilic/hydrophobic organic fractions in di erent MW ranges. Then, the nanofiltration (NF) membrane fouling experiments were carried out using the above fractionated water to investigate the e ect of MW distribution and hydrophilic/hydrophobic characteristics of EfOM on the membrane flux decline using the fractionated water samples. The experimental results have shown that 45.61% of the total organics belongs to the low MW one, among which the percentage of the hydrophilic organics with low MW (less than 2 kDa) was up to 28.07%, while that of the hydrophobic organics was 17.54%. In particular, the hydrophilic fraction was found to be the most abundant fraction in the e uents. MW distribution has a significant e ect on the membrane fouling. When the MWwas less than 30 kDa, the lower the MW, the larger was the specific flux decline, while in the case of MW higher than 30 kDa, the higher the MW, the larger was the specific flux decline, and the decline degree of low MW organics was larger than the high MW one. With the same MW distribution range, specific flux decline of the hydrophilic organic was considerably slower than that of the hydrophobic organic, which indicated that the hydrophobic organic fractions dominantly contribute to the flux decline.     

Effects of ozonation and coagulation on effluent organic matter characteristics and ultrafiltration membrane fouling

Effluent organic matter （EfOM） is the major cause of fouling in the low pressure membranes process for wastewater reuse. Coagulation and oxidation of biological wastewater treatment effluent have been applied for the fouling control of microfiltration membranes. However, the change in EfOM structure by pre-treatments has not been clearly identified. The changes of EfOM characteristics induced by coagulation and ozonation were investigated through size exclusion chromatography, UV/Vis spectrophotometry, fluorescence spectrophotometry and titrimetric analysis to identify the mechanisms in the reduction of ultrafiltration （UF） membrane fouling. The results indicated that reduction of flux decline by coagulation was due to modified characteristics of dissolved organic carbon （DOC） content. Total concentration of DOC was not reduced by ozonation. However, the mass fraction of the molecules with molecular weight larger than 5 kDa, fluorescence intensity, aromaticity, highly condensed chromophores, average molecular weight and soluble microbial byproducts decreased greatly after ozonation. These results indicated that EfOM was partially oxidized by ozonation to low molecular weight, highly charged compounds with abundant electron- withdrawing functional groups, which are favourable for alleviating UF membrane flux decline.