Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems (CuCr₂O₄, CuCo₂O₄), deposited onto cordierite monoliths of honeycomb structure with a second support (finely dispersed Al₂O₃), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine's gas exhausts (O₂, NO_x, H₂O, CO₂) and O₃ as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO₂. Oxidants used can be arranged with reference to decreasing their activity in a following series: O₃ ? NO₂ > H₂O > NO > O₂ > CO₂. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O₃ occurs intensively (in the presence of copper chromite based catalyst) even at closing to ambient temperatures. Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the “cold start” problem.     

Oxidation of diesel soot on binary oxide CuCr(Co)-based monoliths

Binary oxide systems(Cu Cr2O4, Cu Co2O4), deposited onto cordierite monoliths of honeycomb structure with a second support(finely dispersed Al2O3), were prepared as filters for catalytic combustion of diesel soot using internal combustion engine’s gas exhausts(O2, NOx, H2 O, CO2) and O3 as oxidizing agents. It is shown that the second support increases soot capacity of aforementioned filters, and causes dispersion of the particles of spinel phases as active components enhancing thereby catalyst activity and selectivity of soot combustion to CO2. Oxidants used can be arranged with reference to decreasing their activity in a following series: O3 NO2> H2 O > NO > O2> CO2. Ozone proved to be the most efficient oxidizing agent: the diesel soot combustion by O3 occurs intensively(in the presence of copper chromite based catalyst) even at closing to ambient temperatures.Results obtained give a basis for the conclusion that using a catalytic coating on soot filters in the form of aforementioned binary oxide systems and ozone as the initiator of the oxidation processes is a promising approach in solving the problem of comprehensive purification of automotive exhaust gases at relatively low temperatures, known as the "cold start" problem.     

富氧条件下SnO2/Al2O3催化剂上丙烯选择性还原NOx的研究

考察了分别用浸渍法、共沉淀法和溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂上丙烯选择性还原NO_x的催化活性,发现制备方法与Sn的负载量对其活性有重要影响.溶胶-凝胶法制备的SnO₂/Al₂O₃催化剂活性最高,Sn的最佳负载量为5%.与浸渍法和共沉淀法制备的5%SnO₂/Al₂O₃催化剂相比,溶胶-凝胶法制备的5%SnO₂/Al₂O₃催化剂受水蒸汽的抑制作用较弱,并且在水和SO₂共存的条件下活性最高.此外,反应气中丙烯及氧气浓度的增加有利于NO_x转化率的提高.     

不同方法制备Co3O4催化剂CO-SCR性能及机制

氮氧化物(NOx)是造成细颗粒物、近地面臭氧等大气污染问题的重要前体物.随着大气污染治理行动的深入,对工业锅炉/窑炉烟气排放的NOx进行控制十分重要.采用不同方法制备了一系列Co_3O_4催化剂,考察了不同制备方法对CO选择性催化还原NO(CO-SCR)反应活性的影响,通过BET、XRD、Raman、HR-TEM和SEM等技术对该系列催化剂进行了表征.活性测试表明,以硫酸钴为前驱体用固态研磨法制备的Co_3O_4-S催化剂具有更优异的CO-SCR反应活性,且表现出较好的抗水蒸气性能,以醋酸钴为前驱体用固态研磨法制备的Co_3O_4-C催化剂显示出较好的抗水性能. NO氧化结果显示,催化剂的NO氧化效果越好,CO-SCR活性也越好. Raman表征结果显示,Co_3O_4-S表面可能含有更多的Co2+离子,从而有利于形成氧空位. H2-TPR结果表明,Co_3O_4-S催化剂的氧化还原性较好. HR-TEM表征发现Co_3O_4-S和Co_3O_4-O主要暴露(111)和(220)晶面,而更多(220)晶面的暴露可能更有利于反应的进行.     

纳米Fe3O4/CeO2-H2O2非均相类Fenton体系对3,4-二氯三氟甲苯的降解

以浸渍法制备的新型纳米Fe3O4/Ce O2为催化剂,3,4-二氯三氟甲苯(3,4-DCBTE)为目标污染物,在Fe3O4/Ce O2-H2O2非均相类Fenton体系中对目标污染物的降解进行研究,考察催化剂的催化效果和温度、p H、H2O2投加量等因素对催化剂催化效果的影响.结果表明,以纳米Fe3O4/Ce O2作为催化剂的非均相类Fenton体系对3,4-二氯三氟甲苯的处理效果极佳;随着温度的升高,纳米Fe3O4/Ce O2的催化效果不断提高;在偏酸性环境中,p H越低催化效果越好,p H=2时反应去除效率可达96.67%;随着H2O2投加量的增加,3,4-二氯三氟甲苯的降解效率先提高后降低,投加量为15 mg·L-1时去除效果最好可达99.47%;随着催化剂投加量的增加,同样出现了处理效果先升高后降低的现象,投加量为0.5 g·L-1时催化效果最好可达99.64%.在以纳米Fe3O4/Ce O2为催化剂的非均相类Fenton体系中,3,4-二氯三氟甲苯的降解符合一级反应动力学,反应所需活化能较低只需30.26 k J·mol-1.     

Characterization and performance of Pt/SBA-15 for low-temperature SCR of NO by C3H6

Pt supported on mesoporous silica SBA-15 was investigated as a catalyst for low temperature selective catalytic reduction(SCR) of NO by C 3 H 6 in the presence of excess oxygen.The prepared catalysts were characterized by means of XRD,BET surface area,TEM,NO-TPD,NO/C 3 H 6-TPO,NH 3-TPD,XPS and 27 Al MAS NMR.The effects of Pt loading amount,O 2 /C 3 H 6 concentration,and incorporation of Al into SBA-15 have been studied.It was found that the removal efficiency increased significantly after Pt loading,but an optimal loading amount was observed.In particular,under an atmosphere of 150 ppm NO,150 ppm C 3 H 6,and 18 vol.% O 2,0.5% Pt/SBA-15 showed remarkably high catalytic performance giving 80.1% NOx reduction and 87.04% C 3 H 6 conversion simultaneously at 140°C.The enhanced SCR activity of Pt/SBA-15 is associated with its outstanding oxidation activities of NO to NO 2 and C 3 H 6 to CO 2 in low temperature range.The research results also suggested that higher concentration of O 2 and higher concentration of C 3 H 6 favored NO removal.The incorporation of Al into SBA-15 improved catalytic performance,which could be ascribed to the enhancement of catalyst surface acidity caused by tetrahedrally coordinated AlO 4.Moreover,the catalysts could be easily reused and possessed good stability.     

柴油表征燃料在高浓度CO2氛围下燃烧机理的分析

为研究高浓度CO₂在高温高压情况下对柴油燃烧特性的影响,提出了柴油表征燃料在CO₂/O₂氛围下的燃烧反应机理.通过量子化学计算了化学反应路径并对反应路径进行分析,最后进行柴油表征燃料燃烧的仿真.通过搭建定容燃烧弹试验台架和可视化系统进行试验与仿真分析,结果表明：在50% CO₂+50% O₂氛围下,对仿真与实验的火焰燃烧极限长度和火焰纵截面面积进行对比,最小误差分别为0.39%和0.64%,最大误差分别为8.54%和4.94%,说明此机理适用于高浓度CO₂氛围下柴油燃烧特性的研究;CO₂的化学效应在柴油表征燃料燃烧时具有促进作用,CO₂在2600 K时发生热解,热解产物CO与H自由基等发生反应可以生成着火促进剂·OH;柴油在50% CO₂+50% O₂、43% CO₂+57% O₂和35% CO₂+65% O₂氛围下的燃烧效率比空气氛围分别提高了28.2%、30.4%和33.3%.     

三维有序介孔Co3O4非均相活化单过硫酸氢钾降解罗丹明B

以多孔硅KIT-6为模板,采用纳米浇筑法制备三维有序介孔Co_3O_4,利用比表面积测试仪(BET)、高倍投射电子显微镜(H-TEM)、X射线衍射光谱(XRD)、X射线光电子能谱(XPS)、傅里叶变换红外光谱(FT-IR)等方法进行表征,并首次将其应用于催化单过硫酸盐降解罗丹明B.结果表明,三维有序介孔Co_3O_4具有丰富的空间介孔结构和巨大的比表面积,对单过硫酸盐的催化活性远强于传统纳米级Co_3O_4.较高的催化剂投加量和较高的单过硫酸盐浓度有利于罗丹明B的脱色.在反应体系中出现Cl-和H2PO-4能够加速罗丹明B的脱色,而出现NO_3~-、SO_4~(2-)和HCO_3~-则会抑制罗丹明B的去除.通过自由基鉴定实验发现,硫酸自由基是导致罗丹明B脱色的主导活性自由基.三维有序介孔Co_3O_4经过多次重复使用后仍表现出良好的催化活性.     

过氧化氢存在下HCFC－22光解特性

模拟大气条件研究了ＨＣＦＣ－２２＋Ｈ２Ｏ２在有氧或无氧存在下用低压相进行辐照,在２０ｍ的长光程池中用富里叶红外光仪测量其化学产物,结果表明在没有氧情况下产物为ＣＯＦ２,ＣＯ２,ＨＦ和ＨＣｌ;有氧存在时产物为ＣＯ２,Ｈ２Ｏ,ＨＦ和ＨＣｌ。从这些产物推广其可能的光解机理。     

UV/H2O2氧化降解克拉霉素的反应动力学及影响因素

克拉霉素用量大、检出频率高、生态风险大,已被欧盟列为优先监测污染物.针对传统污水处理厂难以完全去除克拉霉素的问题,主要研究了UV/H_2O_2降解克拉霉素的效果和反应动力学,探讨了pH、天然有机质(NOM)和水中共存阴、阳离子对UV/H_2O_2降解克拉霉素的影响.结果表明:单一UV对克拉霉素的光降解符合准一级反应动力学模型,其反应速率常数为0.0016 min~(-1).UV/H_2O_2对克拉霉素的降解符合准一级反应动力学模型,且克拉霉素的降解速率随H_2O_2浓度的增大而增大,在H_2O_2浓度为40 mmol·L~(-1)时,克拉霉素降解的反应速率常数为0.0284min~(-1).克拉霉素与·OH的二级反应速率常数为(2.36±0.20)×10~(10)L·mol~(-1)·s~(-1).碱性条件有利于克拉霉素的降解;NOM(2~10 mg·L~(-1))会抑制克拉霉素的降解,且随NOM浓度增大而增大;共存阴离子CO_3~(2-)对克拉霉素降解无影响,HCO_3~-、NO_3~-、Cl~-会抑制克拉霉素的降解,抑制程度的大小顺序为NO_3~-HCO_3~-Cl~-;共存阳离子Ca~(2+)、Mg2+、Cu~(2+)、Fe~(3+)会抑制克拉霉素的降解,抑制程度的大小顺序为Fe~(3+)Cu~(2+)Mg2+Ca~(2+).     

Effects of Ce on catalytic combustion of methane over Pd-Pt/Al2O3 catalyst

Activity and stability of 1%Pd-0.2%Pt/Al₂O₃ and 1%Pd-0.2%Pt/0.6%Ce/Al₂O₃ catalysts prepared by impregnation method for catalytic combustion of methane in air were investigated. The catalysts before and after reaction were characterized by BET, CO chemisorption, XRD and XPS techniques. Results showed that the presence of Ce significantly increased the activity and thermal stability of the Pd-Pt/Al₂O₃ catalyst towards methane combustion, which could be attributed to more highly-dispersed active PdO particles over the Pd-Pt/Ce/Al₂O₃ catalyst surface as well as the retarded sintering of PdO and the maintained oxidized state of surface Pd during the combustion process in the presence of Ce.     

Fe2O3/TiO2负载膨胀珍珠岩光催化降解罗丹明B

为获得高效催化活性的光催化材料,研究不同煅烧氛围对材料在可见光下催化性能的影响,以膨胀珍珠岩（EP）为载体,采用溶胶-凝胶法,在不同煅烧氛围（O₂和/或NH₃）下制备Fe₂O₃/TiO₂负载EP的光催化复合材料〔Fe₂O₃-TEP（O₂）、Fe₂O₃-TEP（NH₃）、Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）〕,采用EDS（X-射线色散能谱）、BET（比表面积及孔径分析）、XRD（X射线衍射）、SEM（扫描电子显微镜）、XPS（X射线光电子能谱）等对复合材料进行表征,并研究了其在可见光下对罗丹明B的光催化降解效果.结果表明:①复合材料成功负载了Ti、Fe元素,负载的TiO₂以锐钛矿型存在,Fe₂O₃的掺杂增强了TiO₂对可见光的响应能力;②不同的煅烧氛围明显影响复合材料的晶粒尺寸、比表面积和光催化性能,其中,Fe₂O₃-TEP（O₂,NH₃）的光催化性能最好,4 h后罗丹明B降解率达到87.59%,Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）4 h后对罗丹明B的降解率则分别为65.02%、62.48%和47.48%;③在试验条件下,复合材料的光催化反应符合一阶反应动力学方程,Fe₂O₃-TEP（O₂,NH₃）、Fe₂O₃-TEP（NH₃,O₂）、Fe₂O₃-TEP（O₂）和Fe₂O₃-TEP（NH₃）相应的降解速率常数分别为0.008 3、0.004 3、0.004 3和0.002 7 min-1.研究显示,通过溶胶-凝胶法所制备的复合材料（Fe₂O₃-TEP）经煅烧后所得矿相均一;Fe₂O₃掺杂TiO₂可形成Ti—O—Fe键,减小TiO₂固有的禁带宽度;复合材料光催化性能也受到煅烧氛围的影响,先O₂后NH₃煅烧条件下所得材料的光催化性能最佳.      

温和条件下磁性Pd-MgFe2O4/MgAl(O)催化4-氯苯酚高效加氢脱氯

以镁铁尖晶石MgFe₂O₄为磁核,在磁核表层包覆MgAl水滑石后经高温焙烧形成MgAl （O）复合氧化物包覆的磁性载体MgFe₂O₄/MgAl （O）,进而负载纳米金属Pd制成磁性催化剂Pd-MgFe₂O₄/MgAl （O）.通过X射线衍射（XRD）、X射线光电子能谱分析（XPS）、傅里叶红外光谱（FT-IR）、透射电镜（TEM）、扫描电子显微镜（SEM）、选区电子衍射（SAED）、比表面积（S_BET）和振动样品磁强计（VSM）等手段对催化材料进行表征.结果表明,MgFe₂O₄-LDH转化为磁性MgFe₂O₄/MgAl （O）载体有利于催化材料比表面积的增加、结构稳定性的提升及相应催化活性位点的增加,进而有利于提升4-氯苯酚高效加氢脱氯效率.研究进一步考察了催化剂负载量、催化剂用量、底物浓度、反应温度、反应溶剂等条件对4-氯苯酚降解效率的影响.结果发现,在优化反应条件下催化反应的转换频率TOF （0.04 s^-1）可媲美常温、常压、无碱性添加剂等温和条件下4-氯苯酚高效加氢脱氯反应的最佳文献报道水平.磁性催化剂Pd-MgFe₂O₄/MgAl （O）循环使用4次后仍保持很好的催化活性.     

BiOCl/SiO2/Fe3O4复合材料可见光催化去除水中亚甲基蓝

以FeCl_3·6H_2O、FeCl_2·4H_2O、(C_2H_5)_4SiO_4、Bi(NO_3)_3·5H_2O、KCl为主要原料,采用化学共沉淀法和水热法制备了BiOCl/SiO_2/Fe_3O_4光催化剂,并对其进行EDS、TEM、XRD、FT-IR、UV-Vis表征,最后通过亚甲基蓝降解实验,研究了催化剂在合成过程中pH及催化剂投加量对其光催化性能的影响.结果表明,在pH=6、催化剂初始投加量为0.5 g·L~(-1)时,对亚甲基蓝的可见光催化效果最佳,光照120 min后对10 mg·L~(-1)的亚甲基蓝溶液的脱色率达到93.2%.BiOCl/SiO_2/Fe_3O_4经过简单的无水乙醇和水洗后,可高效重复利用4次.综合表明,BiOCl/SiO_2/Fe_3O_4是一种在处理染料废水中具有应用前景的磁性光催化剂.     

Sulfur evolution in chemical looping combustion of coal with MnFe2O4 oxygen carrier

Chemical looping combustion （CLC） of coal has gained increasing attention as a novel combustion technology for its advantages in CO2 capture. Sulfur evolution from coal causes great harm from either the CLC operational or environmental perspective. In this research, a combined MnFe2O4 oxygen carrier （OC） was synthesized and its reaction with a typical Chinese high sulfur coal, Liuzhi （LZ） bituminous coal, was performed in a thermogravimetric analyzer （TGA）-Fourier transform infrared （FT-IR） spectrometer. Evolution of sulfur species during reaction of LZ coal with MnFeaO40C was systematically investigated through experimental means combined with thermodynamic simulation. TGA-FTIR analysis of the LZ reaction with MnFe2O4 indicated MnFe2O4 exhibited the desired superior reactivity compared to the single reference oxides Mn304 or Fe203, and SO2 produced was mainly related to oxidization of H2S by MnFe2O4. Experimental analysis of the LZ coal reaction with MnFe2O4, including X-ray diffraction and X-ray photoelectron spectroscopy analysis, verified that the main reduced counterparts of MnFe2O4 were Fe304 and MnO, in good agreement with the related thermodynamic simulation. The obtained MnO was beneficial to stabilize the reduced MnFe2O4 and avoid serious sintering, although the oxygen in MnO was not fully utilized. Meanwhile, most sulfur present in LZ coal was converted to solid MnS during LZ reaction with MnFe2O4, which was further oxidized to MnSO4. Finally, the formation of both MnS and such manganese silicates as Mn2SiO4 and MnSiO3 should be addressed to ensure the full regeneration of the reduced MnFe2O4.     

UV/H2O2降解美罗培南的影响因素及毒性研究

利用波长为254 nm的紫外灯活化过氧化氢(H_2O_2)氧化降解美罗培南(MPN),考察了H_2O_2投加量、初始pH值、水中常见共存阴离子(Cl~-、HCO~-_3、NO~-_3)和天然有机化合物(NOM)等重要影响因素对MPN降解的影响.结果表明,紫外光功率为4 W,初始pH为7.0,n(H_2O_2)/n(MPN)=20∶1时,反应20 min后,MPN的降解率达到97.8%.H_2O_2投加量的增加会加快MPN的降解速率,Cl~-和HCO~-_3对UV/H_2O_2体系中MPN去除效果的影响较小,极少量的NO~-_3会促进MPN的降解,当NO~-_3的浓度≥10 mg·L~(-1)时,MPN的降解受到抑制,且离子浓度越高,抑制程度表现越明显.NOM的存在对MPN的降解有抑制作用.与纯水相比,MPN在实际水体中的去除受到抑制,归因于水体基质的影响.大肠杆菌的急性毒性实验研究表明,MPN的中间转化产物保留了一些抗菌性能,但光解的最终产物无抗菌性能.     

基于碳捕集的富氧燃煤烟气联合脱硫脱硝试验研究

富氧燃煤烟气压缩液化CO2的高压低温工况为NO氧化为易溶于水的NO2提供了十分有利的条件.基于小型高压吸收试验装置,采用配制的富氧燃煤模拟烟气,在高压常温下进行了NO、SO2、O2与H2O的吸收反应试验.根据反应前后的气液产物分析,测定了不同组分比例与不同压力下混合气体中NO与SO2的转化率.NO氧化与吸收试验表明,NO转化为HNO3的比率随压力升高而增加,在0.5 ～2 MPa之间增加很快,在2 ～3 MPa之间增速趋丁平缓,压力达3 MPa以上时,90％以上的NO均转化为稀硝酸,且初始NO浓度越高,NO的转化率越大.混合气体中同时存在5O2与NO的联合吸收试验发现,只有少量的NO转化成了NO3-,SO2向H2SO4的转化率随压力升高而增加,初始SO2浓度越大,转化率越高.分析表明,SO2与NO同时存在时SO2先行转化为SO3,NO充当了催化剂,但SO2转化为SO3的一次转化率小于35％,反应酸液产物的多次循环能使SO2的转化率达到90％以上.建议的工艺流程中需采用两座吸收反应塔顺序脱除SO2与NO并回收稀酸溶液,有望在富氧燃煤发电捕集CO2系统中降低脱硫脱硝成本,部分地弥补富氧燃烧机组发电成本的增加.     

Ce-Mn/Al2O3-H2O2催化氧化皮革废水的研究

以浸渍法制备了Ce-Mn/Al_2O_3催化剂,研究该催化剂在H_2O_2非均相类Fenton体系中对皮革废水污染物的催化降解性能.在单因素试验的基础上,以COD去除率为响应值,采用Box-Behnken响应曲面法考察了催化剂投加量、H_2O_2投加量、初始pH、反应时间等4个因素之间的单独作用及交互作用,实验数据用Design-Expert 8.0.6软件进行处理,得到二次响应曲面模型.结果表明,4个独立变量对响应值的影响顺序如下:初始pHH_2O_2投加量催化剂投加量反应时间,数学模型拟合度高(R_(adj)~2=0.9349),利用该模型预测的最大COD去除率为78.86%,最佳反应条件为:催化剂投加量56.63 g·L~(-1),H_2O_2投加量315.15 mg·L~(-1),初始pH3.51,反应时间2 h,经实验验证COD去除率为80.94%,与模型预测值偏差2.08%.     

Activity and hydrothermal stability of CeO2–ZrO2–WO3 for the selective catalytic reduction of NOx with NH3

A series of CeO_2–ZrO_2–WO_3(CZW)catalysts prepared by a hydrothermal synthesis method showed excellent catalytic activity for selective catalytic reduction(SCR)of NO with NH_3 over a wide temperature of 150–550°C.The effect of hydrothermal treatment of CZW catalysts on SCR activity was investigated in the presence of 10% H_2O.The fresh catalyst showed above 90% NO_x conversion at 201–459°C,which is applicable to diesel exhaust NO_x purification(200–440°C).The SCR activity results indicated that hydrothermal aging decreased the SCR activity of CZW at low temperatures(below 300°C),while the activity was notably enhanced at high temperature(above 450°C).The aged CZW catalyst(hydrothermal aging at 700°C for 8 hr)showed almost 80% NO_x conversion at 229–550°C,while the V_2O_5–WO_3/TiO_2 catalyst presented above 80% NO_x conversion at 308–370°C.The effect of structural changes,acidity,and redox properties of CZW on the SCR activity was investigated.The results indicated that the excellent hydrothermal stability of CZW was mainly due to the CeO_2–ZrO_2 solid solution,amorphous WO_3 phase and optimal acidity.In addition,the formation of WO_3 clusters increased in size as the hydrothermal aging temperature increased,resulting in the collapse of structure,which could further affect the acidity and redox properties.     

Cu-Al2O3中骨架铜类芬顿催化去除水中有机污染物

为解决传统铁基芬顿催化剂在水体通常酸碱(pH6)条件下活性低的问题,采用简单共沉淀法制备了Cu掺杂的Al_2O_3类芬顿催化剂.通过X射线衍射(XRD)、X射线光电子能谱(XPS)和紫外可见(UV-vis)吸收光谱分析表明,Cu-Al_2O_3中铜掺杂的质量分数低于4.77%时,催化剂中铜主要以Cu~(2+)和Cu~+的形式共存于Al_2O_3的骨架结构中,形成Al—O—Cu键;过量的铜掺杂会导致外骨架铜物种如铜氧化物团簇的存在.以难降解有机污染物2-氯苯酚(2-chlorophenol,2-CP)和染料罗丹明B(Rhodamine B,Rh B)为目标污染物,对Cu-Al_2O_3的类芬顿催化性能进行了详细地研究.结果表明,骨架铜物种在中性温和条件下对2-CP和Rh B显示出很高的催化去除效率和稳定性,反应2 h,Cu-Al_2O_3(Cu质量分数4.77%)对2-CP的去除率达到54%,相应的TOC去除率达到49%,而铜离子溶出浓度仅为0.025 5 mg·L-1,而Cu-Al_2O_3(Cu质量分数7.58%)由于外骨架铜的存在导致催化活性增加缓慢和稳定性下降.ESR测试结果表明,·OH和HO_2~-/O_2~-·是反应中主要的活性物种.